Panasonic Digital Video Cassette Recorder AG DV2000P Operating Instructions

							Select Start Assemble to start editing,
and then press OK.
Editing begins after the playback unit and the
recording VCR both rewind their tapes to the edit
start points.
After completing editing, select Review,
and then press OK.
The edited pictures are played back.
To interrupt editing or Review:
Press EDIT MENU.
Notes:
The Preview function cannot be used with the Assemble
function.
Up to ±1 second of slight deviation in the specified edit
start/end position can be corrected. See pages 62-63 for
Edit Timing Adjustment.
51 
						

							Program Insert
This function is used to replace the picture and sound on a recorded tape.
Preparations
Complete necessary connections and settings.
See pages 24-33.
Example: Video Insert
Operations
Press EDIT MENU.
On Screen Display
Select  Program Editing,  and then
Press OK.
Notes:
Program Editing can be performed using either the tape
counter or Time code display.
If you attempt to switch to the tape counter display in order to
perform editing after setting the editing points using the Time
code display, the Erase all programs screen is displayed.
(The Erase all programs screen is also displayed when you
change from the tape counter display to the Time code
display.)
After setting a program, if you attempt to set another program in a different editing mode, the set contents for the
previous editing mode remain on the setting screen. In
order to prevent editing errors, perform the Erase all
programs operation (page 61) whenever you set a program
under a different editing mode.
Program Editing can not be performed with a movie camera
that has a 4-digit counter. Video Insert and Audio Insert are not possible in the
following cases:
When the tape in the recording VCR (this unit) is:
Recorded in LP mode;
Blank, or contains a blank portion in the middle.
52 
						

							Select the desired editing operation, and
then press OK.
To insert picture: Video Insert.
To insert sound: Audio Insert.
To insert picture and sound: AV Insert.
Press PLAYER and JOG/SHUTTLE.
The picture from the playback unit appears on the
screen.
Search for the edit start point on the
playback unit and press MARK IN.
Search for the edit end point on the
playback unit and press MARK OUT.
(Continued on next page)
AV Insert is not possible in the following cases:
When the tape in the recording VCR (this unit) is:
Recorded in 16bit audio mode;
Recorded in LP mode:
Blank, or contains a blank portion in the middle.
When INPUT SELECT is set to DV IN.
Notes on editing point setting
The Program Insert and Audio Dubbing functions require
the setting of only three editing points: the in and out points
on the playback unit and the in point on the recording unit,
or the in point on the playback unit and the in and out points
on the recording unit.
If both in and out points are set on both the playback unit
and the recording unit, and the times between the points do
not match, editing stops at the first out point that is reached.In order to ensure that the editing operation is performed
properly, the editing points should be set at least 20
seconds after the beginning of the tape.
The editing operation may not be performed correctly if the
set duration of a program is less than 4 seconds.
On video equipment whose Time code display or tape
counter display does not show the frame value, the area
where the frame value is displayed appears as “00f” or it
remains blank.
With some units, the frame value may be displayed when
MARK IN or MARK OUT is pressed in steps 5 and 6 even if
the unit concerned does not show the frame value.
53 
						

							Program Insert (continued)
Press RECORDER  and JOG/
SHUTTLE.
The picture from the recording VCR appears on the
screen.
On Screen Display
Search for the edit start point on the
recording VCR and press  MARK IN.
Press OK.
To check and change programs:
Select Confirm/Change  and then press OK.
To confirm, change, insert or erase editing programs,
see pages 60-61.
To continue setting programs:
1  Press  EDIT MENU.
2  Press  PLAYER.
3  Using
select the program number.
The program number changes each time these buttons are
pressed.
Up to 10 programs can be set.
4  Repeat steps  4-9.
54 
						

							Select Preview to confirm the editing
operation before performing actual
editing, and then press OK.
Preview begins after the playback unit and the
recording VCR both rewind their tapes to the edit
start points.
Select Start Insert to start editing, and
then press OK.
Editing begins after the playback unit and the
recording VCR both rewind their tapes to the edit
start points.
After completing editing, select Review,
and then press OK.
The edited pictures are played back.
To interrupt editing, Preview or Review:
Press EDIT MENU.
Note:
Up to ±1 second of slight deviation in the specified edit start/
end position can be corrected. See pages 62-63 for Edit
Timing Adjustment.
55 
						

							Program Audio Dubbing
This function is used to add new sound on the STEREO2 track of previously recorded tape.
Preparations
Complete necessary connections and settings.
See pages 24-33.
Operations
Press EDIT MENU.
On Screen Display
Select  Program Editing,  and then
Press OK.
Notes:
Program Editing can be performed using either the tape
counter or Time code display.
If you attempt to switch to the tape counter display in order
to perform editing after setting the editing points using the
Time code display, the Erase all programs screen is
displayed.
(The Erase all programs screen is also displayed when you
change from the tape counter display to the Time code
display.)
Program editing can not be performed with a movie camera
that has a 4-digit counter. After setting a program, if you attempt to set another
program in a different editing mode, the set contents for the
previous editing mode remain on the setting screen. In
order to prevent editing errors, perform the Erase all
programs operation (page 61) whenever you set a program under a different editing mode.
Audio Dubbing is not possible in the following cases:
When the tape in the recording VCR (this unit) is:Recorded in 16bit audio mode;
Recorded in LP mode;
Blank, or contains a blank portion in the middle
When INPUT SELECT is set to DV IN.
56 
						

							Select Audio Dubbing, and then press
OK.
Press PLAYER and JOG/SHUTTLE.
The picture from the playback unit appears on the
screen.
Search for the edit start point on the
playback unit and press MARK IN.
Search for the edit end point on the
playback unit and press MARK OUT.
(Continued on next page)
Notes on editing point setting
The Program Insert and Audio Dubbing functions require
the setting of only three editing points: the in and out points
on the playback unit and the in point on the recording unit,
or the in point on the playback unit and the in and out points
on the recording unit.
If both in and out points are set on both the playback unit
and the recording unit, and the times between the points do
not match, editing stops at the first out point that is reached.
In order to ensure that the editing operation is performed
properly, the editing points should be set at least 20
seconds after the beginning of the tape.The editing operation may not be performed correctly if the
set duration of a program is less than 4 seconds.
On video equipment whose Time code display or tape
counter display does not show the frame value, the area
where the frame value is displayed appears as “00f” or it
remains blank.
With some units, the frame value may be displayed when
MARK IN or MARK OUT is pressed in steps 5 and 6 even if
the unit concerned does not show the frame value.
57 
						

							Program Audio Dubbing (continued)
Press RECORDER  and JOG/
SHUTTLE.
The picture from the recording VCR appears on the
screen.
Search for the edit start point on the
recording VCR and press  MARK IN.
Press OK.
To check and change programs:
Select Confirm/Change  and then press OK.
To confirm, change, insert or erase editing programs,
see pages 60-61.
To continue setting programs:
1  Press  EDIT MENU.
2  Press  PLAYER.
3  Using
select the program number.
The program number changes each time these buttons
are pressed.
Up to 10 programs can be set.
4  Repeat steps  4-9.
58 
						

							Select Preview to confirm the editing
operation before performing actual
editing, and then press OK.
Preview begins after the playback unit and the
recording VCR both rewind their tapes to the edit
start points.
Select Start Dubbing to start editing,
and then press OK.
Editing begins after the playback unit and the
recording VCR both rewind their tapes to the edit
start points.
After completing editing, select Review,
and then press OK.
The edited sounds are played back.
To interrupt editing, Preview or Review:
Press EDIT MENU.
To monitor the edited audio after Audio
Dubbing
Press STEREO SELECT during playback and select
STEREO2.
Note:
Up to ±1 second of slight deviation in the specified edit start/
end position can be corrected. See pages 62-63 for Edit
Timing Adjustment.
59 
						

							Other Editing Functions
These functions are used to confirm, change, etc. programs.
Once all program settings are completed, the screen
shown at right is displayed.
Example: Video Insert
This portion varies,
depending on the
editing function that
was programed.
On Screen Display
To check/change programs:
1  Select  Confirm/Change,  and then press OK.
The program list for the playback unit is displayed.
To check the program list for the recording unit, press
RECORDER.
To just confirm the program settings, press EDIT MENU.
If corrections are needed, continue with the procedure
described below.
2  Select the program number for which changes are to be
made, and then press OK.
The Program Change screen for the selected program
number is displayed.
3  Press  JOG/SHUTTLE.
4  Use the Jog Dial/Shuttle Ring to search for the editing
point that is to be corrected.
5  To change an edit start point, press  MARK IN.
To change an edit end point, press MARK OUT.
6 Once all changes are completed, press  OK.
7  Press  EDIT MENU.
On Screen Display
60