Panasonic DLP Based Projector PT-D7500U PT-D7600U Operating Instructions

31
An interface (D-SUB BNC) is necessary to connect the projector with a PC using an analog RGB signal input
module.
1. Connecting analog RGB signals

PC
R/PRG/Y B/PBH/H·VV
D-
SUB     BNC
R    G    B            V
RGB signal input module (optional)
ET-MD95RGB
RGB Module
ET-MD95RGB
H/ H.
V
• The module does not support the three value
synchronizing input to the H/H•V and V terminals.
• Do not supply synchronizing input signals to H/H•V and V
terminals when supplying SYNC ON GREEN signals.
Attention
(Please...

32
1. Connecting the video signals
Image signalLuminance
 signalColor 
signal
Monitor TV Video signal input module (optional)
ET-MD95VM2
DVD player Video deck (TBC built-in)
LINE/Cr IN
C/Cb IN LINE OUT
Y  IN
S terminal    BNC
S terminal
Video Module
ET-MD95VM2
BS digital HD tuner
Image signal
• An optional slot selector (AUX) button toggles between the LINE and Y/C input.
(Example)  Each time AUX button is pressed,
LINE input Y/C input
The above cycle is repeated.
• When connecting with a video deck, be...

33
2. Connecting the component signals
Color-difference 
signals Cb
DVD player
LINE/Cr IN
C/Cb IN LINE OUT
Y  INVideo Module
ET-MD95VM2
Video signal input module (optional)
ET-MD95VM2
Color-difference 
signals CrLuminance signals Y
Video deck (TBC built-in)
• For details on switching between the video signals connection and the component signals connection, refer
to the section for switching the signals of ET-MD95VM2 (optional) on page 67. 

34
• Insert the input module suitable for the input signal specifications.
• Use the SYSTEM SELECTOR button to toggle the systems of the input module that supports two types of
signal specifications. Upon toggling, the input signals are displayed on the screen and cleared automatically.
SD signal
SD signal output
(active through) Serial digital input module (optional)
ET-MD95SD1 (for 480i/576i)
IN  OUT
Business digital
 video deck
480i Module
ET-MD95SD1  SERIAL
Connecting the signal to the serial digital...

35
1. For 480p dual link (4:2:2p) SMPTE294M-compliant, 720x483 active line 59.94 Hz
progressive scan 270 Mbps
• Insert the input module that meets the input signal specifications.
• Use the SYSTEM SELECTOR button to select the input module that meets desired one of the above four
types of signal specifications.  While toggling through those four types, input signal and other information
are displayed and cleared on the screen automatically.
• Normally, use SYSTEM SELECTOR in “AUTO”.
• Automatic detection...

36
• Insert the input module that meets the input signal specifications.
• Use the SYSTEM SELECTOR button to select the input module that meets desired one of the eight types
(14 formats) of signal specifications (SMPTE292M).
While toggling through those eight types, input signal and other information are displayed and cleared on the
screen automatically.
• Normally, use SYSTEM SELECTOR in “AUTO”.
• Automatic detection may malfunction if connection is made in any other way than listed above or if any...

37
DVI-D IN DVI-D OUTDVI Module
ET-MD75DV
ET-MD75DV DVI-D input module (optional)
 DVI signal
PC with DVI output
Connecting signals to the DVI signal input module
External view
• Pin assignments and signal names of DIV-D input
terminal are listed in the table at right (terminal for
TMDS-equipped PC). Pin No. Pin No.      Signal
TMDS data 2–
TMDS data 2+
TMDS data 2 / 4
shield
T.M.D.S data 4–
T.M.D.S data 4+
DDC clock
DDC data 
T.M.D.S data 1–
T.M.D.S data 1+
T.M.D.S data 1/3
shield
T.M.D.S data 3–...

38
How to install and remove the projection lens(optional)
How to install the
projection lens
While pressing the lock button on the
projection lens cover, pull the cover
forward to remove it. (Figure 1)
Pull and remove the dustproof sheet on
the back of the projection lens cover.
Insert while aligning the projection lens
side mark (orange) with the set side
mark. (Figure 2)
Turn the lens clockwise until it clicks.
Insert the tab at the left of the
projection lens cover into the projector
and while...

39
Powering up the projector
Connect the supplied power cable. 
(120 V AC, 50 Hz/60 Hz)
Press the “I” marked side of the MAIN
POWER switch to turn on the power.
The power indicator lamp on the projector will flash
in red.  After a short period, the indicator will
illuminate and the projector will enter standby
mode.
Press the “l” button. [on the main unit
or the remote control]
The power indicator lamp illuminates in green and
soon the image is projected on the screen.
Making adjustment and
selection...

40
Powering off the projector
Press the POWER OFF “” button.
Select “EXECUTE” with  or  button
and press the ENTER button.
(or press the POWER OFF “” button
again.)
A message “UNDER SHUTDOWN 20 SECONDS”
appears and the projection of the image stops
when the count turns to zero.
(The power indicator lamp of the main unit turns to
orange. The cooling fan keeps running still after
the projection stopped.)
Wait until the power indicator lamp of
the main unit turns to red (i.e., until the
cooling fan stops)....