Panasonic DLP Based Projector PT-DZ8700U PT-DS8500U PT-DW8300U Operating Instructions

							NETWORK menu
ENGLISH - 101
Settings
E-mail setup page 
J
With this projector, if a problem occurs or if the lamp usage time reaches a set value, an \
e-mail message can 
be sent to one or more preset e-mail addresses (maximum two addresses)\
.
Click [Detailed set up], then [E-mail set up] to display the E-mail setu\
p page.
 
Select “Enable” to use the E-mail function.
 Enter the IP address or server name of the E-mail 
server (SMTP). The DNS server must be set if 
the server name is entered.
  Enter the E-mail address of the projector.
  (maximum 63 characters)
 The user can enter the location of, for example, 
the installed projector so that the recipient 
may easily identify the originator of the E-mail. 
(maximum 63 characters)
 The user can modify the minimum time interval 
of temperature warning mail. The default value 
is 60 minutes. In this case, the user cannot 
send another mail for 60 minutes after sending 
previous temperature warning mail even the set 
warning temperature is reached again.
 Enter the E-mail address of your desired 
recipient.
 Select the conditions for sending E-mail.
 MAIL CONTENTS: Select [NORMAL] or [SIMPLE].
ERROR: an error is detected by self-diagnosis.
LAMP1 RUNTIME: remaining lamp service time has reached the value set in the field.
LAMP2 RUNTIME: remaining lamp service time has reached the value set in the field.
FILTER REMAIN: remaining filter service time has reached the value set in the field.
INPUT AIR TEMPERATURE: intake air temperature has reached the value set in the field. 
						

							NETWORK menu
102 - ENGLISH
Settings
 Check these boxes when E-mail is to be sent periodically to the second E-mail address. E-mail will be sent 
at the times and on the days checked. 
						

							NETWORK menu
ENGLISH - 103
Settings
E-mail setup page (continued) 
J
 
Enter the E-mail address to which the E-mail is to be sent when two E-mail addresses are going to be 
used. Do not enter it when the second E-mail address is not going to be \
used.
 Select the conditions for sending E-mail to the second E-mail address.
MAIL CONTENTS: Select [NORMAL] or [SIMPLE].
ERROR: an error is detected by self-diagnosis.
LAMP1 RUNTIME: remaining lamp service time has reached the value set in the field.
LAMP2 RUNTIME: remaining lamp service time has reached the value set in the field.
FILTER REMAIN:
INPUT AIR TEMPERATURE: intake air temperature has reached the value set in the field.
 Check these boxes when E-mail is to be sent periodically to the second E-mail address. E-mail will be sent 
at the times and on the days checked.
 Button to update settings 
						

							NETWORK menu
104 - ENGLISH
Settings
Authentication set up page 
J
The POP/SMTP server is set on this page when POP/SMTP authentication is required for mail transmissions.
Click [Detailed set up], then [Authentication set up] to display the Authentication server setup page.
 
Select the authentication method specified by 
your Internet service provider.
 Set this if SMTP authentication has been 
selected.
  POP server name field
  Available input characters:  
Alphanumeric characters (A - Z, a - z, 0 - 9), 
hyphen (-), period (.)
 POP/SMTP server user name field
 POP/SMTP server password field
 Enter the port number for the SMTP server 
(normally “25”).
 Enter the port number for the POP server 
(normally “110”).
  Button to update settings
Ping test page 
J
This page makes it possible to check whether the network is connected to\
 the E-mail server, POP server, 
DNS server, etc.
Click [Detailed set up], then [Ping test] to display the Ping test page.\
 
Enter the IP address of the server to be tested.
 Button for conducting the test.
Display which appears when the connection 
failed.
Display which appears when the connection 
was successful. 
						

							NETWORK menu
ENGLISH - 105
Settings
Contents of mail sent 
J
Mail with the contents shown below is sent when the E-mail settings have\
 been  
Q
established.
ùùùÜ			*		/	+	*	%	Ü	,	.	+	&	!		0	+	.Ü	.	!	,	+	.	0äÿ		
						
åÜùùù
		.	+	&	!		0	+	.Ü		5	,	!ÜÜÜÜÜÜÜÜÜÜöÜ		ææææ
		!	.	%		(Ü	
	+ÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜöÜ		íîïðñòó
éééééÜÜ	
é	)		%	(Ü	/	!	0	1	,Ü	 		0	Üééééé
		
				
	ý				
Ü	ý		
		
	Ü		
			Ü
				
						Ü					
ÜÜÜÜÜÜÜÜÜÜÜ		0Ü	Üòì	Ü	)	%	*	1	0	!	/Ü	%	*	0	!	.	2		(Ü
		
			Üý		Ü		
				
	ý				
ÜÜ		2	!	.Ü	ÜðñÿÜëÜííï	Ü	Ü
	
				ÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜ	Ü			Ü	Ü
	ý			íÜ			
					
ÜÜÜÜÜÜÜÜÜÜÜ	Ü			Ü	ÜÜÜ		0Ü		
		ý		
Ü	Üðìì	Ü	Ü
	ý			íÜ			
					
ÜÜÜÜÜÜÜÜÜÜÜ	Ü			Ü	ÜÜÜ		0Ü		
		ý		
Ü	Üîìì	Ü	Ü
	ý			îÜ			
					
ÜÜÜÜÜÜÜÜÜÜÜ	Ü			Ü	ÜÜÜ		0Ü		
		ý		
Ü	Üðìì	Ü	Ü
	ý			îÜ			
					
ÜÜÜÜÜÜÜÜÜÜÜ	Ü			Ü	ÜÜÜ		0Ü		
		ý		
Ü	Üîìì	Ü	Ü
					
	Ü		
		ý		
ÜÜÜÜÜÜÜÜÜÜÜ	Ü			Ü	ÜÜÜ		0Ü		
		ý		
Ü	Üðìì	Ü	Ü
					
	Ü		
		ý		
ÜÜÜÜÜÜÜÜÜÜÜ	Ü			Ü	ÜÜÜ		0Ü		
		ý		
Ü	Üîìì	Ü	Ü
		
			Üý		Ü		
				
	ý				
ÜÜÜ	Ü			Ü	Ü
		
					ÿÜ		
				Ü
		1	*	 		5ÜÜÜÜ	Ü			Ü	ÜÜ			+	*	 		5ÜÜÜÜ	Ü			Ü	ÜÜ		1	!	/	 		5ÜÜÜ	Ü			Ü	ÜÜ		!	 	*	!	/	 		5Ü	Ü			Ü	Ü
		$	1	.	/	 		5ÜÜ	Ü			Ü	ÜÜ		.	%	 		5ÜÜÜÜ	Ü			Ü	ÜÜ			0	1	.	 		5ÜÜ	Ü			Ü	Ü
ììöììÜÜ	Ü			Ü	ÜÜÜÜìíöììÜÜ	Ü			Ü	ÜÜÜÜìîöììÜÜ	Ü			Ü	ÜÜÜÜìïöììÜÜ	Ü			Ü	Ü
ìðöììÜÜ	Ü			Ü	ÜÜÜÜìñöììÜÜ	Ü			Ü	ÜÜÜÜìòöììÜÜ	Ü			Ü	ÜÜÜÜìóöììÜÜ	Ü			Ü	Ü
ìôöììÜÜ	Ü			Ü	ÜÜÜÜìõöììÜÜ	Ü			Ü	ÜÜÜÜíìöììÜÜ	Ü			Ü	ÜÜÜÜííöììÜÜ	Ü			Ü	Ü
íîöììÜÜ	Ü			Ü	ÜÜÜÜíïöììÜÜ	Ü			Ü	ÜÜÜÜíðöììÜÜ	Ü			Ü	ÜÜÜÜíñöììÜÜ	Ü			Ü	Ü
íòöììÜÜ	Ü			Ü	ÜÜÜÜíóöììÜÜ	Ü			Ü	ÜÜÜÜíôöììÜÜ	Ü			Ü	ÜÜÜÜíõöììÜÜ	Ü			Ü	Ü
îìöììÜÜ	Ü			Ü	ÜÜÜÜîíöììÜÜ	Ü			Ü	ÜÜÜÜîîöììÜÜ	Ü			Ü	ÜÜÜÜîïöììÜÜ	Ü			Ü	Ü
éééééÜÜ		$	!		Ü	/	5	/	0	!	)Üééééé
		ý		
Üÿ		Üþ		ÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜ	ÜÜÜ		ÜÜÜ	
	ý	
ÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜ	ÜÜÜ		ÜÜÜ	
		
			Üý		Ü		
				
	ý				
ÜÜÜÜÜÜÜÜÜ	ÜÜÜ		ÜÜÜ	
				ÿ	Ü							
Ü		
				
	ý				
ÜÜÜÜÜ	ÜÜÜ		ÜÜÜ	
ý				
	Ü	ý			Ü		
				
	ý				
ÜÜÜÜÜÜÜ	ÜÜÜ		ÜÜÜ	
Mail with the contents shown below is sent when an error has occurred. 
Q
ùùùÜ			*		/	+	*	%	Ü	,	.	+	&	!		0	+	.Ü	.	!	,	+	.	0ä	
				åÜùùù
		.	+	&	!		0	+	.Ü		5	,	!ÜÜÜÜÜÜÜÜÜÜöÜ		ææææ
		!	.	%		(Ü	
	+ÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜöÜ		íîïðñòó
éééééÜÜ		$	!		Ü	/	5	/	0	!	)Üééééé
		ý		
Üÿ		Üþ		ÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜ	ÜÜÜ		ÜÜÜ	
	ý	
ÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜ	ÜÜÜ		ÜÜÜ	
		
			Üý		Ü		
				
	ý				
ÜÜÜÜÜÜÜÜÜ	ÜÜÜ		ÜÜÜ	
				ÿ	Ü							
Ü		
				
	ý				
ÜÜÜÜÜ	ÜÜÜ		ÜÜÜ	
ý				
	Ü	ý			Ü		
				
	ý				
ÜÜÜÜÜÜÜ	ÜÜÜ		ÜÜÜ	
	ý			íÜ		
		ý		
Ü					
ÜÜÜÜÜÜÜÜÜÜÜÜÜ	ÜÜÜ		ÜÜÜ	
	ý			îÜ		
		ý		
Ü					
ÜÜÜÜÜÜÜÜÜÜÜÜÜ	Ü	ý			
	Ü	
	ý			íÜ		ý			ÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜ	ÜÜÜ		ÜÜÜ	
	ý			îÜ		ý			ÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜ	ÜÜÜ		ÜÜÜ	
ý		
					
äÿ		
		ý		é						
	åÜÜÜÜ	ÜÜÜ		ÜÜÜ	
		
			Üý		Ü		
			ê		
	
			ÜÜÜÜÜÜÜÜÜ	ÜÜÜ		ÜÜÜ	
				ÿ	Ü							
Ü		
			ê		
	
			ÜÜÜÜÜ	ÜÜÜ		ÜÜÜ	
ý				
	Ü	ý			Ü		
			ê		
	
			ÜÜÜÜÜÜÜ	ÜÜÜ		ÜÜÜ	
þý			
		ÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜ	ÜÜÜ		ÜÜÜ	
ý						Ü		
	
			ÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜ	ÜÜÜ		ÜÜÜ	
ÿ			
	Ü			
	
ÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜ	ÜÜÜ		ÜÜÜ	
þ						
	
		Ü		
	
			ÜÜÜÜÜÜÜÜÜÜÜÜÜ	ÜÜÜ		ÜÜÜ	
ýÿ	Ü		
		ÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜ	ÜÜÜ		ÜÜÜ	
					
	Ü		
		ý		
ÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜ	ÜÜÜ		ÜÜÜ	
ýÿÜ				
	ÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜ	ÜÜÜ		ÜÜÜ	
ä	
	.	.	+	.Ü		+	 	!ÜìíÜììÜììÜììÜììÜììÜììÜììå
		*	,	1	0Ü		%	.Ü	0	!	)	,	!	.		0	1	.	!ÜÜÜÜÜÜöÜíôÜ	 	!	#ÿÜëÜÜòðÜ	 	!	#	
		,	0	%		/Ü	)	+	 	1	(	!Ü	0	!	)	,	!	.		0	1	.	!ÜÜöÜîìÜ	 	!	#ÿÜëÜÜòôÜ	 	!	#	
ý	.	+	1	*	 Ü	(		)	,Ü	0	!	)	,	!	.		0	1	.	!ÜÜÜÜöÜîñÜ	 	!	#ÿÜëÜÜóóÜ	 	!	#	
		
	Ü			
					
ÜÜÜÜÜÜîìììÜ	
				
	Ü		
ÜÜÜÜÜÜÜÜÜÜíììÜ	0	%	)	!	/
	ý			íÜ		
ÜÜÜÜÜÜÜÜÜÜíììÜ	0	%	)	!	/
	ý			íÜ			ÜÜÜÜÜÜÜÜÜÜÜìÜ	
	ý			íÜ				ÜÜÜÜÜÜÜîìììÜ	
	ý			íÜ		
		ý		
ÜÜÜÜÜÜÜÜìÜ	
	ý			îÜ		
ÜÜÜÜÜÜÜÜÜÜÜÜìÜ	0	%	)	!	/
	ý			îÜ			ÜÜÜÜÜÜÜÜÜÜÜìÜ	
	ý			îÜ				ÜÜÜÜÜÜÜÜÜÜìÜ	
	ý			îÜ		
		ý		
ÜÜÜÜÜîìììÜ	
éééééééÜ		!	)		%	*	%	*	#Ü		%	(	0	!	.Üéééééééé
	
	ý	
				ÜÜÜÜÜÜÜÜÜÜíììÜá
ý						êÜ					
ÜÜÜíììììÜ	
ééééééééÜÿ	1	.	.	!	*	0Ü	/	0		0	1	/Üééééééééé
		ý		
Ü		
					
ÜÜÜÜÜÜÜÜÜíêììÜ
	
	
					Ü		
					
ÜÜÜÜÜÜíêìì 
						

							NETWORK menu
106 - ENGLISH
Settings
 
JAdjust clock page
Click [Detailed set up], then [Adjust clock] to display the Adjust clock page.
 
Time zone selection
 Button to update time zone setting
  Turn this [ON] to set the date and time 
automatically.
 When setting the date and time automatically, 
input the IP address or name of the NTP server.  
(When inputting the server name, the DNS server 
must be set.)
 New date field
 New time field
 Button to update time and date settings
Note
If the time becomes incorrect immediately after setting the correct time\
, then the battery needs to be changed.  
 
z
Contact the dealer where you bought the projector to have the battery ch\
anged.
 
JNetwork config page
Click [Detailed set up], then [Network config] to display the Network config page.
If [Network config] is clicked, the "CAUTION!" screen is displayed.
 
z
If the [Next] button is clicked, the current settings are displayed. 
z
If the [Change] button is clicked, the following setting change screen i\
s displayed.  
z
  Enter the name of the projector here. Enter the 
host name here if it is required when the DHCP 
server is going to be used, for instance.
 Set this to ON to enable the DHCP client function.
  Enter the IP address if DHCP server is not used.
 Enter the SUBNET MASK if DHCP server is not 
used.
 Enter the gateway address if DHCP server is not 
used.
 DNS server address (primary) field
  Available input characters:  
Numeric characters (0 - 9), period (.)  
(Example: 192.168.0.253)
 DNS server address (secondary) field
  Available input characters:  
Numeric characters (0 - 9), period (.)  
(Example: 192.168.0.254)
 When all options are filled, click [NEXT]. The 
confirmation screen will be displayed.  
Click [Submit] button to update. 
						

							ENGLISH - 107
Maintenance
Monitor Lamp indicators
Managing the indicated problems
If a problem should occur with the projector, the indicators will inform you. Manage the indicated problems as 
follow.Attention
 
JLAMP1/LAMP2 indicator
Lamp 
indication Information
Check point Remedial measure
Lighting in red Indicates the time 
for replacing the 
lamp unit. Did you notice a “REPLACE 
 
z
LAMP” message on the screen 
when turning on the projector 
power supply? This lamp monitor lights up when the 
 
z
lamp unit used hours have reached 
2 800 hours (when [HIGH] is selected 
as the [LAMP POWER] setting).
Request the dealer to replace the lamp 
 
z
unit.
Blinking in red   (once) Lamp unit is not 
installed. Check the lamp unit 
 
z
compartment. Install the lamp unit.
 
z
When lamp unit is installed and still  
z
having the indicator lights, contact to 
the dealer.
Blinking in red   (3 times) Error is detected 
in the lamp circuit. Did you turn the power back 
 
z
on immediately after turning it 
off? Wait until the lamp has cooled off, and 
 
z
then turn on the power.
Some error has arisen in the 
 
z
lamp circuit.
Check for fluctuation (or drop) 
 
z
in the source voltage. Turn off the MAIN POWER switch 
 
z
using the procedure on page 40 and 
consult the dealer.
Note
If no problem is found or the problem remains, do not turn on the projec\
tor. Instead contact your dealer.
 
z
Filter indicator (FILTER)
Temperature indicator (TEMP)
Lamp2 indicator (LAMP2)
Lamp1 indicator (LAMP1)Power indicator  
(STANDBY (R) / ON (G)) 
						

							Monitor Lamp indicators
108 - ENGLISH
Maintenance
 
JTEMP indicator
Lamp 
indication Information
Check point Remedial measure
Lighting in red Warm-up status
Did you turn on the power when 
 
z
the ambient temperature was 
lower than approx. 0 °C (32 °F)? Wait about 5 minutes in the current 
 
z
status.
Install the unit in a location having 
 
z
an ambient temperature from 0 °C 
(32 °F) - 45 °C (113 °F).
High temperature 
inside. (WARNING) Check the ventilation port is 
 
z
blocked.
Is the room air temperature too 
 
z
high?
Is the filter indicator lighted? 
 
z
Remove the object that is blocking  
z
the ventilation port.
Move the projector to a temperature 
 
z
of 0 °C (32 °F) - 45 °C (113 °F) and 
the humidity of 20 % to 80 % (no 
condensation).
Turn off the MAIN POWER switch 
 
z
using the procedure on page 40 and 
replace the ACF unit.
Blinking in red  
(once) The filter is 
excessively dirty 
and the ventilation 
is poor.
Blinking in red   (twice) High temperature 
inside.  
(Standby condition)
Blinking in red   (3 times) Cooling fan has 
been stopped.
—Turn off the MAIN POWER switch 
 
z
using the procedure on page 40 and 
consult the dealer.
Note
If no problem is found or the problem remains, do not turn on the projec\
tor. Instead contact your dealer.
 
z
 
JFILTER indicator
Lamp 
indication Information
Check point Remedial measure
Lighting in red The ACF unit has 
run out. Check the [REMAINING 
 
z
FILTER] of [STATUS] in 
[PROJECTOR SETUP] menu. 
(
Æpage  83) Replace the ACF unit.
 
z
Blinking in red The ACF unit is not 
installed. Check the ACF unit  
z
compartment. Replace the ACF unit. 
z
Lighting in 
orange The ACF unit 
remains few. The 
remaining use time 
of the ACF unit is 
approximately 200 
hours. Check the [REMAINING 
 
z
FILTER] of [STATUS] in 
[PROJECTOR SETUP] menu. 
(
Æpage  83) Request the dealer to purchase the 
 
z
new ACF unit.
Blinking in  orange The ACF unit cannot 
operate properly. Is foreign object blocking the 
 
z
ACF unit operation? Remove the foreign object from the 
 
z
ACF unit.
When the foreign object still 
 
z
remained, contact the dealer.
Note
If no problem is found or the problem remains, do not turn on the projec\
tor. Instead contact your dealer.
 
z
When the ACF unit is not installed, the filter indicator will blink in red and the power will turn off in 10 minutes. 
 
z
When the FILTER indicator is flashing green, the Auto Cleaning Filter (ACF) is normally rolling up.
 
z
When the ACF unit is operating, operational sound may be heard.
 
z
The usable time after lighting of the orange lamp may be shortened in a \
dusty environment. The time of about 200 hours is 
 
z
for reference only. Contact the dealer to purchase the new ACF unit earlier.
If the projector is used at elevations higher than 1 400 m above sea level with the [HIGH ALTITUDE MODE] at [OFF], the 
 
z
lamp life or life of other components will be shortened.
Before the FILTER indicator blinks in orange when operational malfunction, mechanical \
sound of the clutch may be heard.
 
z
If the Smoke Cut Filter is installed, the green lamp, which takes longer to turn ON/OFF , will flash.
 
z
If the filter is running low, only one lamp lights even if [DUAL] is selected. The lamps will light as normal once the filter has 
 
z
been replaced and the residual filter has been reset.  
						

							ENGLISH - 109
Maintenance
Replacement
Before replacing the unit
Turn off the POWER switch of the projector in proper way and disconnect the pow\
er plug from the wall outlet.  
z
(Æpages  38, 40)
Be sure to observe the procedure “Powering off the projector” 
 
z(Æpage  40) when performing power supply 
operation.
Replacing the unit
 
JACF (Auto Cleaning Filter) unit
ACF unit is an optional accessory.
You can check the remaining amount of the ACF unit in [REMAINING FILTER] of [STATUS] in PROJECTOR 
SETUP menu. (
Æpage
 83)
Contact an Authorized Service Center to purchase a Replacement filter unit (ET-ACF310).
 
z
 
JProcedure of ACF unit replacement
Loosen “ACF cover fixing screw” (1 
1  ) 
screw) until the screws turn freely and 
remove the “ACF cover”.
Slide out the “ACF unit” from the 
2  ) 
projector slowly.
When you replace the “ACF unit”, clean the  
z
compartment and/or the air exhaust port if you 
need to.
Insert the new “ACF unit” into the 
3  ) 
compartment in correct direction and 
slightly push until it clicks.
Attach the “ACF cover” and tighten 
4  ) 
“ACF cover fixing screw” (1 screw) 
securely.
Select [FILTER COUNTER RESET] 
5  ) 
in [PROJECTOR SETUP] menu, and 
press  button.  (
Æpage 85)
Press ◄► to select [OK], and press 
6  ) 
 button.
Note
When the ACF unit is not installed, the filter indicator will 
 
z
blink in red and the power will turn off in 10 minutes. (The 
time before the power is turned off is indicated by the unit 
of 1 minute.)
The replacement timing of the ACF depends on 
 
z
environment of usage.
When resetting is performed, the filter will be wound.
 
z
The part numbers of accessories and separately sold 
 
z
components are subject to change without notice.
Always install the ACF unit when using the projector.
 
z
Attention
When installing the ACF unit, take care not to touch the 
 
z
filter surface.
Be sure to install the ACF unit when using the projector.
 
z
The ACF unit to be replaced should be an unused 
 
z
product.
ACF cover
ACF cover fixing screw
ACF unit
CANCEL
OK
EXECUTE CHANGE
[ENTER]
RESET FILTER COUNTER? 
						

							Replacement
110 - ENGLISH
Maintenance
 
JLamp unit
The LAMP unit is consumable product. You can check the duration of usage time using [LAMP1/LAMP2] of 
[STATUS] (
Æpage
 83) in the [PROJECTOR SETUP] menu.
Replacement of the lamp unit should be carried out by a qualified technician.
Contact the dealer to purchase a replacement lamp unit (ET-LAD310:1 bulb unit, ET-LAD310W: 2 bulb units).
 
JPrecautions on lamp unit replacement
Handle the lamp unit with special care as the lamp is made of glass. Dro\
pping or giving it a shock may  
z
cause it to burst or damaged.
Phillips screwdriver is necessary when replacing a lamp unit.
 
z
When replacing the lamp unit, be sure to hold it by the handle. 
z
The lamp may burst. Replace the lamp unit carefully so that the broken p\
ieces of the lamp glass will not  
z
scatter. When the projector is mounted on the ceiling, do not work directly und\
er the projector or put your 
face closer to the projector.
For disposition of used lamps, request an industrial waste disposal cont\
ractor.
 
z
Attention
Do not attempt replacement with an unauthorized lamp unit.
 
z
The part numbers of accessories and separately sold components are subje\
ct to change without notice.
 
z
Wait for more than 1 hour and make sure the lamp unit and the surrounding\
s are cooled enough.
 
z
Prior to replacing the lamp unit, allow it to cool down to prevent the r\
isk of burns, damage and other hazards.
 
z
 
JWhen to replace the lamp unit
When the lamp is consumed, the brightness may decrease over time. 3 000 hours of use is the replacing 
time as a rough guide, and that might be shortened by the usage conditio\
ns, characteristics of the lamp 
unit or environmental conditions.  Therefore, it is strongly recommended for the user to keep a spare lamp.\
 
If the lamp unit has not been replaced after 3 000 hours of operation have elapsed, the power will turn off 
automatically approximately 10 minutes after it is turned on.
On screenLAMP indicator
LAMP
Over 2 800 hours [REPLACE LAMP] is displayed on the upper left 
of the screen for 30 seconds. Press any button to 
clear the screen, or disappears after 30 seconds.
Lights in red.
Over 3 000 hours [REPLACE LAMP] is displayed on the upper left 
of the screen, and it will stay until you respond. To 
clear the screen, press any button.
Note
The guide times, 
 
z 3 000 hours, are rough estimates based on certain conditions and are not a\
 guaranteed time.
REPLACE LAMP