Panasonic Dmc G1 Operating Instructions Manual

							31VQT1U32
Preparation
If there are any white saturated areas, we 
recommend compensating the exposure towards 
negative (P63) referring to the histogram (P56) and 
then taking the picture again. It may result in a better 
quality picture.
There may be white saturated areas if the distance 
between the camera and the subject is too close 
when taking pictures with the flash. 
If [HIGHLIGHT] is set to [ON] in this case, the area directly illuminated by the photo flash will 
become white saturated and appear blinking in black and white.
Press the shutter button halfway or turn the camera off and on to cancel [POWER SAVE].[POWER SAVE] is set to [5MIN.] in the Intelligent auto mode.[POWER SAVE] is fixed to [2MIN.] when [AUTO LCD OFF] is set to [15SEC.] or [30SEC.].Press any button to turn on the LCD monitor again.
Adjust the brightness of the screen with  3/4, contrast and saturation 
with  2/1 or the front dial.
It will adjust the LCD monitor when the LCD monitor is in use, and the 
viewfinder when the viewfinder is in use.
 [HIGHLIGHT]
When the Auto Review function is activated or when playing back, 
white saturated areas appear blinking in black and white.
[OFF]/[ON]
q  [ECONOMY]
You can conserve the battery life by setting these menus.
Also, it will turn off the LCD monitor automatically when not in use 
to prevent discharge of the battery.
p [POWER SAVE]:
The camera is automatically tur ned off if the camera has not been 
used for the time selected on the setting.
[OFF]/[1MIN.]/[2MIN.]/[5MIN.]/[10MIN.]
 [AUTO LCD OFF]:
The LCD monitor is automatically turned off if the camera has not 
been used for the time selected on the setting.
[OFF]/[15SEC.]/[30SEC.]
  [MONITOR]/
[VIEWFINDER]Brightness and color of the LCD monitor/viewfinder can be 
adjusted in 7 steps.
 [LCD MODE]
These menu settings make it easier to see the LCD monitor when 
you are in bright places.
[OFF]
„  [AUTO POWER LCD]:
The brightness is adjusted autom atically depending on how bright 
it is around the camera.
…  [POWER LCD]:
The LCD monitor becomes brighter and easier to see even when 
taking pictures outdoors.
[ON] [OFF]
LCD 
						

							VQT1U3232
Preparation
The brightness of the pictures displayed on the LCD monitor is increased so some subjects 
may appear differently from actuality on the LCD monitor. However, this does not affect the 
recorded pictures.
The LCD monitor automatically returns to normal brightness after 30 seconds when recording 
in Power LCD mode. Press any button to make the LCD monitor bright again.
If the screen is difficult to see because of light from the sun etc. shining on it, use your hand or 
another object to block the light.
The number of recordable pictures decreases in Auto power LCD and Power LCD modes.
The folder number is updated and the file number starts from 0001. (P119)A folder number between 100 and 999 can be assigned.
When the folder number reaches 999, the number cannot be reset. We recommend formatting 
the card (P34) after saving the data on a PC or elsewhere.
To reset the folder number to 100, format the card first and then use this function to reset the 
file number.
A reset screen for the folder number will then appear. Select [YES] to reset the folder number.
When [SETUP] menu settings are reset, the following settings are also reset. In addition, 
[FAVORITE] (P111) in [PLAYBACK] mode menu is set to [OFF], and [ROTATE DISP.] (P112) is 
set to [ON].
–Film mode (P81)–The birthday settings for [BABY1]/[BABY2] (P93) and [PET] (P94) in scene mode.–The [WORLD TIME] (P133) setting.The folder number and the clock setting are not changed.
This will work when the video cable is connected. 
v [NO.RESET]Reset the file number of the next recording to 0001.
w [RESET]The [REC] or [SETUP]/[CUSTOM MENU] menu settings are reset 
to the initial settings.
[BEEP]
Set the focus confirmation beep, the self-timer beep and the 
alarm beep.
[s ] (Muted)
[t ] (Low)
[u ] (High)
 [TV ASPECT]
Set to match the type of TV.
[W ]: When connecting to a 16:9 screen TV.
[X ]: When connecting to a 4:3 screen TV. 
						

							33VQT1U32
Preparation
Interlace method/progressive method
i= interlace scanning is scanning the screen with half of the effective scanning lines every 1/60 
seconds, where p= progressive scanning is a high density image signal that is scanning the 
screen with all the effective scanning lines every 1/60 seconds.
The [HDMI] terminal on this unit is compatible  with high definition output [1080i]. It is necessary 
to have a compatible TV to enjoy progressive and high definition images.
If the images are not output on the TV when the setting is [AUTO], match with the image format 
your TV can display, and select number of effective scanning lines. (Please read the operating 
instructions for the TV.)
This will work when the HDMI mini cable (optional) is connected.Refer to P125 for details.
This will work when the HDMI mini cable (optional) is connected.Refer to P126 for details.
If you set a different language by mistake, select [ ~] from the menu icons to set the desired 
language.
[–. –] is displayed as the lens firmware when the lens is not mounted.
[HDMI MODE]
Set the format for the HDMI output when playing back on the 
HDMI compatible high definition TV connected with this unit using 
the HDMI mini cable (optional).
[AUTO]:
The output resolution is automatically set based on the 
information from the connected TV.
[1080i]:
The interlace method with 1080 available scan lines is used for 
output.
[480p]:
The progressive method with 480 av ailable scan lines is used for 
output.
[VIERA Link]
Setup so this unit can be controlled by the remote control of the 
VIERA by automatically coupling this unit with the VIERA Link 
compatible equipment using HDMI mini cable (optional).
[OFF]: Operation is performed with the buttons on this unit.
[ON]: Remote control operation of the VIERA Link 
compatible equipment is enabled. (Not all operations 
are possible)
Button operation of the main unit will be limited.
~ [LANGUAGE]Set the language displayed on the screen.
[ENGLISH]/[FRANÇAIS]/[ESPAÑOL]/[PORTUGUÊS]
 [VERSION DISP.]This enables the firmware versions of the camera and lens to be 
checked. 
						

							VQT1U3234
Preparation
When [PC] is selected, the camera is connected via the “USB Mass Storage” communication 
system.
When [PictBridge(PTP)] is selected, the camera is connected via the “PTP (Picture Transfer 
Protocol)” communication system.
Use a battery with sufficient battery power or the AC adaptor (P132) when formatting. Do not 
turn the camera off during formatting.
If the card has been formatted on a PC or other equipment, format it on the camera again.If the card cannot be formatted, consult your nearest Service Center.
} [SCENE MENU]
Set the screen that is displayed when the mode dial is set to  , 
, , ,  and .
[OFF]: The recording screen in the currently selected 
advanced scene mode (P88) or scene mode (P92) 
appears.
[AUTO]: The advanced scene mode or scene mode menu 
screen appears.
x [USB MODE]
Select the USB communication system after or before connecting 
the camera to your PC or y our printer with the USB connection 
cable (supplied).
y  [SELECT ON CONNECTION]:
Select either [PC] or [PictBridge(PTP)] if you connected the 
camera to a PC or a printer supporting PictBridge.
z  [PC]:
Set after or before connecting to a PC.
{  [PictBridge(PTP)]:
Set after or before connecting to a printer supporting PictBridge.
 [FORMAT]The card is formatted. 
Formatting irretrievably deletes all the data so check the data 
carefully before formatting.
For Canadian assistance, please call:
1-800-99-LUMIX (1-800-995-8649) or 
send e-mail to: [email protected] USA assistance, please call:
1-800-211-PANA(7262) or, contact us via the web at: 
http://www.panasonic.com/contactinfo          
						

							35VQT1U32
Preparation
About LCD monitor/Viewfinder
This is convenient as it allows you to take pictures from  various angles by adjusting the 
LCD monitor. (P13)
∫ Taking pictures at a normal angle
LCD Monitor
∫Taking pictures at a high angle
Open the LCD monitor 180 o toward you, 
and adjust the angle.

This is convenient when there is someone in 
front of you and you cannot get close to the 
subject.
∫ Taking pictures at a low angle
Open the LCD monitor 180 o toward you, 
and adjust the angle.

This is convenient when taking pictures of 
flowers etc. that are in a low position. 
						

							VQT1U3236
Preparation
∫Taking pictures with the camera held vertically
Open the LCD monitor and rotate it to an angle that makes it easy to see.

Do not cover the AF assist lamp (P10) with your fingers or other objects.
Taking pictures at a normal angle
Pictures recorded with the camera held vertical ly are played back vertically (rotated). (Only 
when [ROTATE DISP.] (P112) is set to [ON])

Pictures may not be displayed vertically if they were taken with the camera aimed up or down.You can only use the direction detection function when using a compatible lens. (P14)
(Refer to the catalog, website etc. for compatible lenses.)
Taking pictures at a high angle Taking pictures at a low angle
Direction detection function 
						

							37VQT1U32
Preparation
∫About the eye sensor automatic switching
Eye sensor is active when the [LVF/LCD AUTO] (P105) in the [CUSTOM MENU] menu is 
set to [ON], switching automatically to view finder display when an eye or object is moved 
closer to the viewfinder, and to LCD monitor display when it is moved away.
A AF assist lamp
When the LCD monitor turns on, the 
Viewfinder turns off (and vice versa).
Eye sensor might not work properly depending 
on the shape of your eyeglasses, the way you 
hold the camera, or bright light shining around 
the eyepiece. Switch manually in that case.
Press [LVF/LCD] to switch the 
monitor screen.
It is possible to switch between the LCD (LCD 
monitor) and LVF (viewfinder) display 
manually.
“LVF” is abbreviation of “Live View Finder” and 
it represents the viewfinder display.
B Viewfinder
C Eye sensor
D LCD monitor
E [LVF/LCD] button
∫Diopter adjustment
Adjust the diopter to suit your vision so that 
you can see the Viewfinder clearly.
Look at the display on the Viewfinder and 
rotate the diopter adjustment dial to 
where the screen is clearest.
Switching the LCD monitor/Viewfinder
99PPAWBAWBAWB100100100µ330µ330 
						

							VQT1U3238
Preparation
Mode switching
Selecting the [REC] Mode
When the [REC] mode is selected, the camera can be set to the Intelligent auto mode in 
which the optimal settings are established in line with the subject to be recorded and the 
recording conditions, or to the scene mode which enables you to take pictures that match 
the scene being recorded.
Turn the camera on.
Switching the mode by rotating the mode 
dial.
Align a desired mode with part  A.
Rotate the mode dial slowly and surely to adjust 
to each mode. (The mode dial rotates 360 o)
∫Basic
Intelligent auto mode (P40)
The subjects are recorded using settings  automatically selected by the camera.
Program AE mode (P44)
The subjects are recorded  using your own settings.
ON
OFF 
						

							39VQT1U32
Preparation
∫Advanced
∫ Advanced scene mode
Aperture-priority AE mode (P84)
The shutter speed is automatically deter mined by the aperture value you set.
Shutter-priority AE mode (P84)
The aperture value is automatically  determined by the shutter speed you set.
Manual exposure mode (P85)
The exposure is adjusted by the aperture value and the shutter speed which are 
manually adjusted.
Custom mode (P97)
Use this mode to take pictures with previously registered settings.
My color mode (P95)
Easily check the color of light, brightness, and vividness of color when the picture is 
taken.
Scene mode (P92)
This allows you to take pictures that match the scene being recorded.
Portrait mode (P89)
Use this mode to take pictures of people.
Scenery mode (P89)
Use this mode to take pictures of scenery.
Sports mode (P90)
Use this mode to take pictures of sporting events, etc.
Close-up mode (P90)
Use this mode to take picture of close-by subject.
Night portrait mode (P91)
Use this mode to take pictures of night scenes and people with night time scenery. 
						

							VQT1U3240
Basic
[REC] mode: ñ
BasicTaking pictures using the automatic function 
(ñ: Intelligent Auto Mode)
The camera will set the most appropriate settings to match the subject and the recording 
conditions so we recommend this mode for beginners or those who want to leave the 
settings to the camera and take pictures easily.

The following functions are activated automatically.–Scene detection /[D.RED-EYE]/ Face detection /Intelligent ISO sensitivity control/
[I.EXPOSURE]/[LONG SHTR NR]/ [QUICK AF]/ [FOCUS PRIORITY]/
Backlight Compensation
Set the mode dial to  [ ].
Set the focus mode dial to [AFS] or [AFC].
Refer to P45 for [AFS] and [AFC].
Hold this unit gently with both hands, keep your 
arms still at your side and stand with your feet 
slightly apart.
A AF assist lamp
The status indicator  3 lights when you turn this 
unit on  2. (1: Shutter button)
ON
OFF