Panasonic Dmc G2k Operating Instructions Manual

							21VQT2S30
Preparation
∫Optical Image Stabilizer
The lens included in DMC-G2K has a stabilizer function.
•
There is no [O.I.S.] switch on the 14 – 42 mm/F3.5 – 5.6 lens included in DMC-G2K. Set the 
[STABILIZER] settings in the [REC] Mode menu. (P129)
Attach the lens cap.
Press the lens release button  D while 
turning the lens as far as possible in the 
direction of the arrow to detach it.
•Always attach the body cap to the camera body so 
that dirt or dust does not get inside.
•Attach the lens rear cap so that the lens contact 
point does not get scratched.
Note
•Change lenses where there is not a lot of dirt or dust. Refer to P186 when dirt or dust gets on 
the lens.
•When you turn the camera off or carry the camera, attach the lens cap to protect the surface of 
the lens.
•Be careful not to lose the lens cap, the lens rear cap and the body cap.
When using a lens with an [O.I.S.] switch, it is 
possible to set to enable the Optical Image Stabilizer 
by switching the [O.I.S.] switch on the lens to [ON].
•
You can change the Optical Image Stabilizer Mode in 
the [REC] Mode menu. (P129) It is set to [MODE1] at 
the time of purchase.
•It is recommended to disable the Optical Image 
Stabilizer when using a tripod. [ ] is displayed on 
the screen at that time. Example when a lens with the 
[O.I.S.] switch is mounted.
Detaching a lens from the camera body
DMC-G2KPP-VQT2S30_eng.book  21 ページ  ２０１０年４月１３日　火曜日　午後９時２０分 
						

							VQT2S3022
Preparation
Attaching the Lens Hood
In bright sunlight or backlight, the lens hood will minimize lens flare and ghosting. The lens 
hood cuts off excess lighting and improves the picture quality.
•
Check that the camera is turned off.•Close the flash.
To attach the lens hood (flower shape) that came with the 14 – 42 mm/F3.5 – 5.6 lens 
included in DMC-G2K
Insert the lens hood into the lens 
with the short sides at the top and 
bottom, and turn in the direction 
of the arrow until it stops.
AFitting to the mark.
∫Temporarily storing the lens hood
1Turn the lens hood in the direction of the arrow to 
detach it.
2Reverse the lens hood and then attach it in the same 
way as shown previously.
•
Attach the lens cap.•When temporarily storing the lens hood, check that it is firmly 
attached and that it does not appear in the picture.
Note
•Hold the short sides of the flower shaped lens hood when attaching or detaching it.•When taking pictures with flash with the lens hood attached, the lower portion of the photo may 
turn dark (vignetting effect) and the control of the flash may be disabled because the photo 
flash may be obscured by the lens hood. We recommend detaching the lens hood.
•When using the AF Assist Lamp in the dark, detach the lens hood.
DMC-G2KPP-VQT2S30_eng.book  22 ページ  ２０１０年４月１３日　火曜日　午後９時２０分 
						

							23VQT2S30
Preparation
Attaching the Shoulder Strap
•We recommend attaching the shoulder strap when using the camera to prevent it from 
dropping.
Pass the shoulder strap through the 
shoulder strap eyelet on the camera body.
A: Shoulder strap eyelet
Pass the end of the shoulder strap through 
the ring in the direction of the arrow and 
then pass it through the stopper.
Pass the end of the shoulder strap through 
the hole on the other side of the stopper.
Pull the other side of the 
shoulder strap and then check 
that it will not come out.
•Perform steps 1 to 4 and then attach 
the other side of the shoulder strap.
Note
•Attach the shoulder strap so that the “LUMIX” LOGO is on the outside.•Use the shoulder strap around your shoulder.–Do not wrap the strap around your neck.–It may result in injury or accident.•Do not leave the shoulder strap where an infant can reach it.–It may result in an accident by mistakenly wrapping around the neck.
DMC-G2KPP-VQT2S30_eng.book  23 ページ  ２０１０年４月１３日　火曜日　午後９時２０分 
						

							VQT2S3024
Preparation
Charging the Battery
∫About batteries that you can use with this unit
The battery that can be used with this unit is DMW-BLB13PP.
•
Use the dedicated charger and battery.•The camera has a function for distinguishing batteries which can be used safely.  The 
dedicated battery  (DMW-BLB13PP) supports this function. The only batteries suitable 
for use with this unit are genuine Panasonic products and batteries manufactured by 
other companies and certified by Panasonic. (Batteries which do not support this 
function cannot be used). Panasonic cannot in any way guarantee the quality, 
performance or safety of batteries which have been manufactured by other companies 
and are not genuine Panasonic products.
∫ Charging
•The battery is not charged when the camera is shipped. Charge the battery before use.•Charge the battery with the charger indoors.•Charge the battery in a temperature between 10 oC to 30 oC (50 oF to 86 oF). (The battery 
temperature should also be the same.)
It has been found that counterfeit battery packs which look very similar to the 
genuine product are made available to purchase in some markets. Some of these 
battery packs are not adequately protected with internal protection to meet the 
requirements of appropriate safety standards. There is a possibility that these 
battery packs may lead to fire or explosion. Please be advised that we are not 
liable for any accident or failure occurring as a result of use of a counterfeit 
battery pack. To ensure that safe products are used we would recommend that a 
genuine Panasonic battery pack is used.
Connect the AC cable.
•The battery cannot be charged when the DC cable 
(DMW-DCC3; optional) is connected to the AC adaptor.
Attach the battery with attention to the 
direction of the battery.
•Disconnect the charger from the electrical socket and 
detach the battery after charging is completed.
DMC-G2KPP-VQT2S30_eng.book  24 ページ  ２０１０年４月１３日　火曜日　午後９時２０分 
						

							25VQT2S30
Preparation
∫ About the [CHARGE] indicator
•
When the [CHARGE] indicator flashes–The battery temperature is too high or too low. Please charge the battery again in a 
temperature between 10 oC to 30 oC (50 oF to 86 oF).
–The terminals of the charger or the battery are dirty. In this case, wipe them with a dry cloth.
∫ Charging time
•
The indicated charging time is for when the battery has been discharged completely. 
The charging time may vary depending on how the battery has been used. The charging 
time for the battery in hot/cold environments or a battery that has not been used for a 
long time may be longer than normal.
Charging time and number of recordable pictures with the optional battery pack 
(DMW-BLB13PP) are the same as above.
∫ Battery indication
The battery indication is displayed on the screen.
[It does not appear when you use the camera with the AC adaptor (P181) connected.]
•
The indication turns red and blinks if the remaining battery power is exhausted. (The status 
indicator also blinks) Recharge the battery or replace it with a fully charged battery.
Note
•Do not use any other AC cables except the supplied one.•The battery becomes warm after using it and during and after charging. The camera also 
becomes warm during use. This is not a malfunction.
•The battery can be recharged even when it still has some charge left, but it is not 
recommended that the battery charge be frequently topped up while the battery is fully 
charged. (Since characteristic swelling may occur.)
•Do not leave any metal items (such as clips) near the contact areas of the power plug. 
Otherwise, a fire and/or electric shocks may be caused by short-circuiting or the 
resulting heat generated.
The [CHARGE] 
indicator turns on: The [CHARGE] indicator A is turned on and charging will start.
The [CHARGE] 
indicator turns off: The [CHARGE] indicator 
A of the charger will turn off once the 
charging has completed without any problem.
Charging time Approx. 155 min
DMC-G2KPP-VQT2S30_eng.book  25 ページ  ２０１０年４月１３日　火曜日　午後９時２０分 
						

							VQT2S3026
Preparation
∫Recording still pictures (when using the LCD monitor) (By CIPA standard in 
Program AE Mode)
∫ Recording still pictures (when using the viewfinder) (By CIPA standard in 
Program AE Mode)
Recording conditions by CIPA standard
•
CIPA is an abbreviation of [Camera & Imaging Products Association].•Temperature: 23 oC (73.4oF)/Humidity: 50% when LCD monitor is on.•Using a Panasonic SD Memory Card (2 GB).•Using the supplied battery.•Starting recording 30 seconds after the camera is turned on.•Recording once every 30 seconds  with full flash every second recording.•Turning the camera off every 10 recordings and leaving it until the temperature of the battery 
decreases.
The number of recordable pictures varies depending on the recording interval time. 
If the recording interval time becomes longer, the number of recordable pictures 
decreases. [For example, if you were to take one picture every two minutes, then the 
number of pictures would be reduced to approximately one-quarter of the number 
of pictures given above (based upon one picture taken every 30 seconds).]
Approximate operating time and number of recordable pictures
When the 14 – 42 mm/F3.5 – 5.6 lens included in DMC-G2K is 
used
Number of recordable  pictures Approx. 360 pictures
Recording time
Approx. 180 min
When the 14 – 42 mm/F3.5 – 5.6 lens included in DMC-G2K is 
used
Number of recordable  pictures Approx. 390 pictures
Recording time
Approx. 195 min
DMC-G2KPP-VQT2S30_eng.book  26 ページ  ２０１０年４月１３日　火曜日　午後９時２０分 
						

							27VQT2S30
Preparation
∫Recording motion pictures (when using the LCD monitor)
–[AVCHD Lite] (Recording with picture quality set to [SH] ([ ]))
–[MOTION JPEG] (Recording with picture quality set to [HD] ([ ]))
•These times are for an ambient temperature of 23 oC (73.4oF) and a humidity of 50%. Please 
be aware that these times are approximate.
•Actual recordable time is the time available for recording when repeating actions such as 
switching the power supply [ON]/[OFF], starting/stopping recording etc.
¢ Motion picture recorded continuously in [MOTION JPEG] is up to 2 GB. Only the maximum 
recordable time for 2 GB is displayed on the screen.
∫Playback (when using the LCD monitor)
Note
•
The operating times and number of recordable pictures will differ according to the 
environment and the operating conditions.
For example, in the following cases, the operating times shorten and the number of recordable 
pictures is reduced.
–In low-temperature environments, such as on ski slopes.–When using [AUTO POWER LCD] or [POWER LCD] (P36).– When flash is used repeatedly.•When the operating time of the camera becomes extremely short even after properly charging 
the battery, the life of the battery may have expired. Buy a new battery.
When the 14 – 42 mm/F3.5 – 5.6 lens included in DMC-G2K is 
used
Continuous 
recordable time
(motion pictures) Approx. 180 min
Actual recordable time
(motion pictures) Approx. 100 min
When the 14 – 42 mm/F3.5 – 5.6 lens included in DMC-G2K is 
used
Continuous 
recordable time
(motion pictures) Approx. 180 min¢
Actual recordable time
(motion pictures) Approx. 100 min¢
When the 14 – 42 mm/F3.5 – 5.6 lens included in DMC-G2K is 
used
Playback time Approx. 330 min
DMC-G2KPP-VQT2S30_eng.book  27 ページ  ２０１０年４月１３日　火曜日　午後９時２０分 
						

							VQT2S3028
Preparation
Inserting and Removing the Card (optional)/the 
Battery
•Check that this unit is turned off.•Close the flash.•We recommend using a Panasonic card.
Slide the release lever in the direction of 
the arrow and open the card/battery 
door.
•Always use genuine Panasonic batteries 
(DMW-BLB13PP).
•If you use other batteries, we cannot guarantee 
the quality of this product.
Battery: Insert until it is locked by the 
lever A being careful about the direction 
you insert it. Pull the lever  A in the 
direction of the arrow to remove the 
battery.
Card: Push it fully until it clicks being 
careful about the direction you insert it. 
To remove the card, push the card until it 
clicks, then pull the card out upright.
B : Do not touch the connection terminals of the 
card.
•
The card may be damaged if it is not fully inserted.
1:Close the card/battery door.
2:Slide the release lever in the direction 
of the arrow.
•If the card/battery door cannot be completely 
closed, remove the card, check its direction and 
then insert it again.
Note
•Remove the battery after use.•Do not remove the battery while the power is on as the settings on the camera may not be 
stored properly.
•The supplied battery is designed only for the camera. Do not use it with any other equipment.•The battery will be exhausted if left for a long period of time after being charged.•Before removing the card or battery, turn the camera off, and wait until the status indicator has 
gone off completely. (Otherwise, this unit may no longer operate normally and the card itself 
may be damaged or the recorded pictures may be lost.)
DMC-G2KPP-VQT2S30_eng.book  28 ページ  ２０１０年４月１３日　火曜日　午後９時２０分 
						

							29VQT2S30
Preparation
About the Card
Access to the card
The access indication lights red when pictures are being recorded 
on the card.
The following cards which conform to the SD video standard can be used with this unit.
(These cards are indicated as card in the text.)
•
Only cards bearing the SDHC logo (indicating that the card conforms to SD video standards) 
may be used as 4 GB to 32 GB cards.
•Only cards bearing the SDXC logo (indicating th at the card conforms to SD video standards) 
may be used as 48 GB to 64 GB cards.
•Use a card with SD Speed Class¢ with “Class 4” or higher when recording motion pictures in 
[AVCHD Lite]. Also, use a card with SD Speed Class with “Class 6” or higher when recording 
motion pictures in [MOTION JPEG].
¢ SD Speed Class is the speed standard regarding continuous writing.
•Please confirm the latest information on the following website.http://panasonic.jp/support/global/cs/dsc/(This Site is English only.)
Note
•Do not turn off the power or remove the battery, card, or the DC cable (DMW-DCC3; 
optional) (when the AC adaptor is in use), while the access indicator is lit, while writing, 
reading, or deleting the picture, formatting (P39), etc. Also, do not apply vibration, 
shock, or static electricity to the unit.
The card or the data on the card may be damaged, and this unit may no longer operate 
normally.
If operation fails due to vibration, impact or static electricity, perform the operation 
again.
•Write-Protect switch A provided (When this switch is set to the [LOCK] position, 
no further data writing, deletion or formatting is possible. The ability to write, delete 
and format data is restored when the switch is returned to its original position.)
•The data on the card may be damaged or lost due to electromagnetic waves, static 
electricity or breakdown of the camera or the card. We recommend storing 
important data on a PC etc.
•Do not format the card on your PC or other equipment. Format it on the camera 
only to ensure proper operation. (P39)
•Keep the Memory Card out of reach of children to prevent swallowing.
Card
Type of card which can be  used with this unitRemarks
SD Memory Card 
(8 MB to 2 GB)•SDHC Memory Card can be used with SDHC Memory Card 
or SDXC Memory Card compatible equipment.
•SDXC Memory Card can only be used with SDXC Memory 
Card compatible equipment.
•Check that the PC and other equipment are compatible when 
using the SDXC Memory Cards.
http://panasonic.net/avc/sdcard/information/SDXC.html
SDHC Memory Card 
(4 GB to 32 GB)
SDXC Memory Card 
(48 GB to 64 GB)
2
A
DMC-G2KPP-VQT2S30_eng.book  29 ページ  ２０１０年４月１３日　火曜日　午後９時２０分 
						

							VQT2S3030
Preparation
Setting Date/Time (Clock Set)
•The clock is not set when the camera is shipped.
Turn the camera on.
A[MENU/SET] button
Press [MENU/SET].
Press  2/1 to select the items (year, month, 
day, hour, minute, display sequence or time 
display format), and press  3/4 to set.
A: Time at the home area
B : Time at the travel destination (P125)
‚ : Cancel without setting the clock.
•
Select either [24HRS] or [AM/PM] for the time display 
format.
•AM/PM is displayed when [AM/PM] is selected.•When [AM/PM] is selected as the time display format, midnight is displayed as 
AM 12:00 and noon is displayed as PM 12:00. This display format is common in the US 
and elsewhere.
Press [MENU/SET] to set.
Press [MENU/SET].
•Press [‚] to return to the settings screen.•Turn the camera off after finishing setting the clock. Then turn it on and check that the 
clock setting is correct.
•When [MENU/SET] has been pressed to complete the settings without the clock having 
been set, set the clock correctly by following the “Changing the clock setting” procedure.
Select [CLOCK SET] in the [SETUP] menu, and press  1. (P32)
•It can be changed in steps 3, 4 and 5 to set the clock.•The clock setting is maintained for 3 months using the built-in clock battery even 
without the battery. (Leave the charged battery in the unit for 24 hours to charge the 
built-in battery.)
Changing the clock setting
ON
OFF
:
:
DMC-G2KPP-VQT2S30_eng.book  30 ページ  ２０１０年４月１３日　火曜日　午後９時２０分