Panasonic Dmp B100 Operating Instructions

							Getting started
VQT2H71
11
∫Detaching the battery pack
When not using for long periods of time
≥Detach the battery pack ( >above).
(Even when the unit is turned off, there is a small amount of 
voltage running through the unit, and this may result in a 
malfunction.)
≥ Recharge the battery for re-use.
∫ Recharging the battery pack
Attach the battery pack and connect the AC 
adaptor ( >10).
≥The [CHARGE] indicator lights while charging the battery, 
and the [CHARGE] indicator turns off when battery charging 
is finished.
∫ Approximate recharging and play times 
(Hours)
≥ Play time indicated above may differ depending on the use.
≥ To change the LCD brightness ( >13, “Adjusting the pictures 
on the LCD screen”).
∫ Checking the remaining battery charge
Not displayed when the AC adaptor is in use.
Press [SUB MENU] while the power is On
Remaining charge is displayed for a few seconds at the bottom 
right of the screen.
Charge the battery pack when the display starts to flash.
≥Appears automatically when there is only a few minutes of 
charge remaining. Before connection, consult your car owner’s manual or your 
dealer.
≥
Connect to the cigarette lighter socket of a vehicle that has a 
12 V battery. It is not compatible with a vehicle that has a 
24 V battery.
≥ This is a special negative grounded Car DC Adaptor. Using 
this Car DC Adaptor with a plus grounded car can cause 
malfunction and lead to fire.
1Connect the car DC adaptor to the unit.
2Connect the car DC adaptor to the cigarette 
lighter socket.
Replacing the fuse
Replace only with the specified 125 V/250 V, 3.15 A fuse. 
Use of any other type can cause fire.
1 Open the socket.
2 Replace the fuse.
3 Close the socket.
Cautions
≥To avoid draining your car battery
jDisconnect the Car DC Adaptor from the cigarette lighter 
after use. The Car DC Adaptor continues to consume some 
power even if it is not being used, and if a battery pack is 
attached to this unit, it will start recharging which uses 
more power.
j Do not use the Car DC Adaptor for long periods when the 
engine is not running.
≥ Leave some slack in the cord.
≥ No responsibility will be taken for damage that occurs due to 
faulty installation.
Recharging*1
*1
When the unit is off [at 20oC (68oF)]
Play*2
*2
At room temperature using headphones [at 20oC (68oF)]
LCD brightness level
s 50r5
53.53.253
RELEASE
DETACH ATTACH
Bottom side of this unit 2Slide.
1 Press and hold.
[CHARGE] indicator
(Orange light)
Recharge
(flashing)
Fully charged
Connecting the included Car DC 
Adaptor
12
Car DC Adaptor (included)

125 V/250 V, 3.15 A type
VQT2H71~Body1_eng.fm  11 ページ  ２００９年１２月２５日　金曜日　午後５時４０分 
						

							VQ T2H71
12
Turning on/off the unit
Press [POWERÍ] (approx. 0.5 sec.).
The unit is turned off when [POWER Í] is pressed again.
≥ The power is shut off if the screen is closed while the power 
is “On”.
≥ When the “Auto Power Off” is set to “On” (initially set to “On”), 
the unit will be turned off automatically after 15 minutes 
(5 minutes when the battery pack is used) when it is in 
stopped status ( >25).
≥ The startup will take time. The operation related to startup of 
the unit after turning on this unit can be quickened by setting 
the initial setup “Quick Start” ( >25) to “On” (initially set to 
“Off”). (The power consumption will increase)
≥ You may hear operational sounds when the unit is turned on, 
but this is due to the initialization of the pickup unit, and it is 
not a malfunction.
After opening the LCD screen and pressing [POWER Í] for 
the 1st time, a screen for the basic settings will appear.
Follow the on-screen instructions and make 
the settings with [ 3,4 ] and [OK].
“On-screen Language” ( >25), “Picture Quality Mode” ( >13) 
and “Quick Start” ( >25) are set.
≥You can perform this setup anytime by selecting “Easy 
Setting” in the Setup menu. ( >25)
≥ You can also change this setting individually. ( >13 , 25)
The unit is turned off automatically after set time has passed.
Switch by pressing the [OFF TIMER].
It will switch every time it is pressed.
Showing FUNCTION 
MENU
Some functions of this unit can be operated from FUNCTION 
MENU.
1Press [FUNCTION MENU].
≥ Functions displayed depend on the media and operating 
conditions.
2Press [ 3,4 ] to select the item and press 
[OK].
Easy Setting
Turn the unit off automatically
Off Timer 0 : 30
e.g., 30 min.
Off1:00
0:30 2:00 3:00 6:0012:00
!Playback ( >14)
! Top Menu ( >14)
! Menu ( >15, 18, 20)
! Viewing Picture  (> 18)
! Viewing Video  (> 14 )
! Listening Music  (> 20)
! Disc  (> 14)
Switches to the disc drive.
! SD card  (> 14)
Switches to the SD drive.
! Other Functions
“Playlists”:
You can play playlists created on DVD-VR.
Press [3,4,2,1] to select the playlist and press [OK].
“Setup” (> 24)
“Card Management” ( >21)
OKRETURN
PlaybackTop Menu
Other Functions
SD card
DISCBlu-ray Disc Player
e.g.,
DMPB100P-VQT2H71_eng.book  12 ページ  ２００９年１２月２４日　木曜日　午後４時５８分 
						

							Getting started
VQT2H71
13
Adjusting the pictures on 
the LCD screen
1Press [LCD MENU].
≥It is also possible to display with the following 
procedures.
2Select the item with [ 3,4].
3Change the setting with [ 3,4,2 ,1 ].
Picture:Adjusting image quality
≥Underlined items are the factory presets.
To exit the screen
Press [EXIT].
Loading the disc or SD 
card
1Press [OPEN].
2Set the disc and close the lid.
≥Set the disc securely until you hear a click, with the 
label side up. (Double-sided disc: place the label side up 
that you want to play back)
≥Some discs may start playing when it is loaded with the unit 
turned on.
≥ About discs with a cartridge
jDVD-RAM, DVD-R: Remove the disc from the cartridge 
and set the disc in the tray. Cartridge discs cannot be used.
j Place the disc back into the cartridge for storage to prevent 
dirt and scratches after use.
≥ Do not touch the lens as it 
may make it dirty.
1Open the cover at the side of the unit.
2Insert the SD card into the SD card slot.
≥With the label side up, insert the card straight in the 
direction shown in the figure, until you hear a sound.
3Close the cover.
To remove the cardIn step 2 above, press the center of the card until it “clicks”, and 
pull the card out straight.
1
Press [SUB MENU].
2 Select “Other Functions” with [ 3,4], and select [OK].
3 Select “LCD Menu” with [ 3,4], and select [OK].
! Standard: Standard
! Dynamic
: Picture with high contrast
! Night: Picture suitable for viewing in dark places
! User jBrightness:  s5 to r 5
j Color:  s5 to  r5
j Tint: s 5 to r5
LCD Menu
PictureDynamic
Brightness
Color
Tint
RETURN
SUB
MENU
Disc
SD card

Lens ( A)
DMPB100P-VQT2H71_eng.book  13 ページ  ２００９年１２月２４日　木曜日　午後４時５８分 
						

							VQ T2H71
14
Playback
Basic play (Playing video 
contents)
Instructions for operations are generally described using the 
remote control in these operating instructions.
Insert a disc or SD card (>13).
Play starts.
≥If play does not start, press [ 1](PLAY).
≥ If a media with data in different file formats is inserted, the file 
selection  menu is displayed. Press [ 3,4 ] to select the 
desired file format and press [OK] .
≥ If the menu is displayed, press [3 ,4 ,2, 1] to select the 
item and press [OK].
≥ If the screen prompting you to use the color buttons appears, 
continue to operate with the color buttons on the remote 
control.
≥DISCS CONTINUE TO ROTATE WHILE MENUS ARE DISPLAYED. 
Press [∫] when you fi nish to preserve the unit’s motor.
≥The producers of the disc can control how discs are played, so you 
may not always be able to control play as described in these 
operating instructions. Read the disc’s instructions carefully.
≥When playing a set of two or more BD-Video discs, the menu 
screen may continue to display even if the disc has been ejected.
≥ The start of playback may take time depending on the disc or 
SD card.
≥ The sound of rotation may be audible during disc playback, 
but this is not a malfunction.
Press [VOL j] or [VOL i].
≥When using headphones, turn down the volume before connection.
Press [DISC/SD] to select “DISC” or “SD”.
≥ If a media is inserted while the unit is stopped, the drive 
switches automatically depending on the inserted media.
[BD-V]  [AVCHD]  [DVD-VR]  [DVD-V]
Press [DIRECT NAVIGATOR/TOP MENU].
≥ Total title number may not be displayed properly on +R/+RW. [BD-V]
The Pop-up menu is a special feature available with some BD-
Video discs. This menu may vary with discs. For the operating 
method, refer to the instructions for the disc.
1
Press [POP-UP MENU].
2 Press [ 3,4, 2,1] to select the item and press [OK].
≥ Pop-up menu also appears by pressing [SUB MENU] and 
selecting “Pop-up Menu”.
≥ Press [POP-UP MENU] to exit the screen.
[AVCHD]  [MPEG2]
It is possible to play the HD (High Definition) video recorded on 
the Panasonic High definition Video Camera on the DVD-RAM/
R/RW/R DL/+R/+RW/+R DL or SD card, and SD (Standard 
Definition) Video recorded on the Panasonic SD Video Camera 
on the SD card.
1Insert a disc or SD card ( >13).
≥“Video (AVCHD)” or “Video (MPEG-2)” screen is 
displayed.
≥ If a media containing data in different file formats is 
inserted, the file selection menu may be displayed.
Press [ 3,4] to select “Play Video (AVCHD)” or “Play 
Video (MPEG-2)” and press [OK].
2Press [ 3,4 ,2 ,1 ] to select the title and 
press [OK].
≥ Total title number may not be displayed properly on +R/
+RW.
To return to the menu screen
Press [DIRECT NAVIGATOR/TOP MENU].
To exit the menu screen
Press [EXIT].
To adjust the volume
To switch drives
To show menus
DIRECT NAVIGATOR Title ViewVideoPicture
01
02
03
04
05
06
07
08
09
10 9/  5
9/  5
9/  5
9/  6
9/  6
9/  6
9/  7
9/  7
9/  7
9/  7
Wed
Wed
Wed
Thu
Thu
Thu
Fri
Fri
Fri
Fri IN 2
IN 2
VHS
VHS  
 
 
IN 2
IN 2 10:00AM
11:30AM11:59PM
10:00AM 11:30AM11:59PM
10:00AM
10:30AM
11:30AM11:59PMRec. Length
No. Date Day
Channel
StartTitle NameDVD-RAM(VR)
RGSUB
MENU PlayPrevious NextRETURNVideo
PictureBYPage  01/02
0:15 (SP)
e.g., DVD-RAM
To show Pop-up menu
Playing HD Video or SD Video
SD Card
Play Video (AVCHD)
Select an action or press [RETURN].
Play Pictures (JPEG)
Play Video (MPEG-2)
OK
RETURN
SUB
MENU
e.g., 
DIRECT NAVIGATORVideo (MPEG-2)Video
001
002
003
004
005
006
007
008
009
0109/  5
9/  5
9/  5
9/  6
9/  6
9/  6
9/  7
9/  7
9/  7
9/  7 Wed
Wed
Wed
Thu
Thu
Thu
Fri
Fri
Fri
Fri  
 
 
10:00AM
11:30AM11:59PM
10:00AM 11:30AM11:59PM
10:00AM
10:30AM
11:30AM11:59PMRec. Length
No. Date Day
Start Title NameSD CARD
SUB
MENU PlayPrevious NextRETURNPage  01/02
0:15.47
e.g.,
DMPB100P-VQT2H71_eng.book  14 ページ  ２００９年１２月２４日　木曜日　午後４時５８分 
						

							Playback
VQT2H71
15
(If the media contains data in different file formats)
1Press [FUNCTION MENU].
2 Press [ 3,4] to select “Menu” and press [OK].
3 Press [ 3,4] to select “Play Video (AVCHD)” or “Play 
Video (MPEG-2)” and press [OK].
≥ It may pause for a few seconds on the break of images when 
editing such as partial deletion is performed.
≥ High definition video (transfer rate of 18 Mbps or faster) 
cannot be played back correctly if it was recorded on a DVD 
compatible to double speed or slower. [DVD-VR]
 [AVCHD]
1Insert a disc or SD card ( >13).
2Press [ 3,4 ] to select the title and press 
[SUB MENU].
3Press [ 3,4 ] to select “View Chapters” and 
press [OK].
4Press [ 3,4 ,2 ,1 ] to select the chapter 
and press [OK].
To return to the previous screen
Press [RETURN].
To exit the screen
Press [EXIT].
To switch from other menus to AVCHD or 
MPEG2 menuChapter playback
Properties
View Chapters
To display the title properties 
(recording date, etc.)
To select the chapter
e.g., 
[AVCHD]
DIRECT NAVIGATORChapter ViewSD CARD
Play
RETURN
2009.11.15Video
Page  01/01
001
---
---
---
---
---
---
---0:00.00002003004
005
e.g.,  [AVCHD]
DMPB100P-VQT2H71_eng.book  15 ページ  ２００９年１２月２４日　木曜日　午後４時５８分 
						

							VQ T2H71
16
These functions may not work depending on the media and 
contents.
The stopped position is memorized.
Resume play function
Press [1] (PLAY) to restart from this position.
≥ The memorized position is cleared in the following instances:
j[∫ ] is pressed several times
j The disc or SD card is removed
j The unit is turned off due to such occurrences as power 
outage, the removal of the AC adaptor or waste of the 
battery pack’s remaining power when the unit is turned on
≥ [BD-V] : On BD-Video discs including BD-J ( >33), the resume 
play function does not work.
≥ [MPEG2] : The position is cleared if the unit is turned off.
≥ Press [ ;] again or [ 1] (PLAY) to restart play.
The speed increases up to 5 steps.
≥ Press [ 1] (PLAY) to revert to normal playback speed.
≥ For some discs, the speed may not change.
Search
While playing, press [ 6] or [ 5].
≥ [DVD-VR]  [DVD-V]: Audio is heard during the first step of 
forward search.
≥ [BD-V]  [AVCHD]  [MPEG2] : Audio is not heard during all steps of 
search.
≥ [CD]  [MP3]: The speed is fixed to a single step.
Slow-motion
While paused, press [ 6] or [ 5].
≥ [BD-V]  [AVCHD] : Forward direction [ 5] only.
≥ [DVD-VR] : If continued for approx. 5 minutes, slow-motion play 
pauses automatically. Skip to the title, chapter or track you want to play.
≥
Each press increases the number of skips.
During playback, you can access specific recordings or scenes 
through direct entry of the numbered buttons. 
Play starts from the selected title or chapter.
≥ While stopped (the image on the right is 
displayed on the screen), the title is 
designated. While playing, the chapter is 
designated.
While paused, press [ 2] (2; ) or [ 1] (;1 ).
Each press shows the next frame.
≥ Press and hold to change in forward or backward 
succession.
≥ Press [ 1] (PLAY) to revert to normal playback speed.
≥ [BD-V]  [AVCHD]  : Forward direction [ 1] (;1) only.
Other operations during play
Stop
Pause
Search/Slow-motion
Skip
Direct Play
[BD-V]  [AVCHD]
e.g.,   5: [0]  B [0]  B [5]
15: [0]  B [1]  B [5] [DVD-V]
e.g.,   5: [0] 
B [5]
15: [1]  B [5]
Frame-by-frame
DMPB100P-VQT2H71_eng.book  16 ページ  ２００９年１２月２４日　木曜日　午後４時５８分 
						

							Playback
VQT2H71
17
When black bars are shown at the top, bottom, left, and right 
sides of the screen, you can enlarge the image to fill the 
screen.
1Press [SUB MENU].
2 Press [ 3,4] to select “Other Functions” and press [OK].
3 Press [ 3,4] to select “Screen Aspect” and press [OK].
4 Press [ 2,1] to select “Side cut” or “Zoom”.
≥ Please note that the top, bottom and sides of the image will 
be cut off in images with no black bars.
≥
Screen aspect will return to “Normal” in the following instances:
j The drive is switched
j The unit is turned on/off
≥ [BD-V]  [DVD-V] : “Side cut” does not have any effect.
The status messages give you information about what is 
currently being played. Each time you press [STATUS], the 
information displayed will change.
≥ It is also possible to display with the following procedures:
1 Press [SUB MENU].
2 Select “Status” with [3, 4], and select [OK]. ≥
It is also possible to display with the following procedures:
1 Press [SUB MENU].
2 Select “Other Functions” with [ 3,4], and select [OK].
3 Select “Audio” with [ 3,4], and select [OK].
[BD-V]  [DVD-V]
You can change the audio channel number each time you 
press [AUDIO] or [ 3,4]. This allows you to change the 
soundtrack language ( >22, “Soundtrack”), etc.
[DVD-VR]  [MPEG2]
AudioLR >AudioL >Audio R
^---------------------------------}
You can change soundtracks each time you press [AUDIO].
Screen Aspect
! Normal: Normal output
! Side cut: The black bars on the right and left sides of 
the 16:9 image disappear and the image is 
enlarged. Please note that the right and left 
sides of the image are cut off when the 
black bar is not displayed.
! Zoom: The black bars on the top and bottom sides 
of the 4:3 image disappear and the image is 
enlarged. Please note that the top and 
bottom sides of the image are cut off when 
the black bar is not displayed.
Status messages
PlayBD-Video
 T1     C1     0:05.140:20.52
T: Title
C: Chapter
PL: Playlist Items change 
depending on the 
disc played.
No display
Current position
Type of disc
Play status
Elapsed time in the title
e.g., 
[BD-V]
Depending on the kind of media or the playback status, this 
display may not appear. Total time
Changing audio
Soundtrack 1 ENG Digital  3/2.1ch
English is selected.
e.g., 
[DVD-V]
Play DVD-RAM(VR) 
AudioLR 
 “AudioLR” 
is selected e.g., 
DMPB100P-VQT2H71_eng.book  17 ページ  ２００９年１２月２４日　木曜日　午後４時５８分 
						

							VQ T2H71
18
Playing still pictures
[JPEG]
Playback of the BD-RE, DVD-RAM/R/R DL or CD-R/RW with 
still pictures recorded. This unit can also play still pictures 
recorded on the SD card.
(About structure of folders >27, “Structure of folders that can 
be played in this unit”)
1Insert a disc or SD card ( >13).
∫ BD-RE, DVD-RAM
“Album View” screen is displayed.
≥When the “Title View” screen is displayed, press the [G] 
button to switch to the “Album View” screen.
≥
If the DVD-RAM containing both JPEG and AVCHD format 
is inserted, the file selection menu may be displayed.
∫ DVD-R/R DL, CD-R/RW, SD card
≥If the media containing data in different file formats is 
inserted, the file selection menu may be displayed.
Press [3,4] to select “Play Pictures (JPEG)” and press [OK].
“Picture View” screen is displayed.
B  Go to step 3
2Press [ 3,4 ,2 ,1 ] to select the album and 
press [OK].
3Press [ 3,4 ,2 ,1 ] to select the still 
picture and press [OK].
≥ Press [ 2,1] to display the previous or next still picture.
≥ Press [ :, 9 ] to show other pages.
≥ Playback is not possible for pictures other than JPEGs.
≥ Black bars may be displayed on the top, bottom or sides 
depending on the picture aspect ratio.
To return to the previous screen
Press [RETURN].
To exit the screen
Press [EXIT]. (If the media contains data in different file formats)
1
Press [FUNCTION MENU].
2 Press [ 3,4] to select “Menu” and press [OK].
3 Press [ 3,4] to select “Play Pictures (JPEG)” and press 
[OK].
You can display still pictures one by one at a constant interval.
∫ BD-RE, DVD-RAM
1While the “Album View” screen is displayed
Press [ 3,4 ,2 ,1 ] to select the album and 
press [SUB MENU].
≥ You can also start slideshow by pressing [ 1](PLAY) 
after selecting the album.
2Press [ 3,4 ] to select “Start Slideshow” 
and press [OK].
∫ DVD-R/R DL, CD-R/RW, SD card
1While the “Picture View” screen is displayed
Press [SUB MENU].
2Press [ 3,4 ] to select “Start Slideshow” 
and press [OK].
To stop slideshow
Press [ ∫].
In step 2 in Start Slideshow ( >above)
1Press [ 3,4 ] to select “Slideshow 
Settings” and press [OK].
2To change the display interval
Press [ 3,4] to select “Display Interval” and press [ 2,1] 
to select the interval (“Long”, “Normal” or “Short”).
≥ When a still picture with a large number of pixels is 
played, the display interval may become longer. Even if 
the setting is changed, the display interval may not 
become shorter.
To set display method
Press [ 3,4] to select “Transition Effect” and press [ 2,1] 
to select “Fade”, “Motion” and “Random”.
SD Card
Play Video (AVCHD)
Select an action or press [RETURN].
Play Pictures (JPEG)
Play Video (MPEG-2)
OK
RETURN
SUB
MENU
e.g.,
Â
RG
 Total 8
106_DVD
 Total 13
2006  9 12
SUB
MENU
DIRECT NAVIGATORAlbum ViewDVD-RAM(VR)Video Picture
OK Press [OK] to go to Picture View.
Previous Next SlideshowRETURNVideo
PictureBYPage  02/02
e.g.,
SUB
MENU Play
RETURNPage  001/001
DIRECT NAVIGATORPicture View
2006  9  12Video PictureDVD-RAM(VR)
0005
0009 0006
00070008
0001
0002 0003 0004
e.g.,
To switch from other menus to JPEG menu
Useful functions during still 
picture play
Start Slideshow
Slideshow settings
!Fade: Pictures are changed by fading out and 
fading in.
! Motion: Pictures are changed by fading out and 
fading in, while they are enlarged, reduced, 
or moved up or down.
! Random: In addition to the “Motion”, pictures are 
changed by various methods.
DMPB100P-VQT2H71_eng.book  18 ページ  ２００９年１２月２４日　木曜日　午後４時５８分 
						

							Playback
VQT2H71
19
To repeat slideshow
Press [3,4] to select “Repeat Play” and press [ 2,1] to 
select “On” or “Off”.
To listen to Background Music (SD card only)
The music CD can be played back as Background Music 
during the slideshow.
Press [ 3,4] to select “Soundtrack” and press [ 2,1 ] to 
select “On” or “Off”.
≥ You cannot search or skip on the music.
≥ When the slideshow stops, the playback of the music 
also stops.
3Press [ 3,4 ,2 ,1] to select “Set” and 
press [OK].
1While playing (except for slideshow)
Press [SUB MENU].
2Press [ 3,4 ] to select “Rotate Right” or 
“Rotate Left” and press [OK].
≥ The rotation information will be stored until the unit is turned 
off or the media is removed.
This function is only available for small-sized still pictures.
1While playing (except for slideshow)
Press [SUB MENU].
2Press [ 3,4 ] to select “Zoom out” and 
press [OK].
≥ The zoom-out information will not be stored.
To cancel “Zoom out”
1 Press [SUB MENU].
2 Select “Zoom in” and press [OK].
∫BD-RE, DVD-RAM
To switch to another higher folder
(Only if there is a multiple number of higher folders 
recognizable)
1While the “Album View” screen is displayed
Press [SUB MENU].
2Press [ 3,4 ] to select “Select Root folder” 
and press [OK].
3Press [ 2,1 ] to select the higher folder and 
press [OK].
∫ DVD-R/R DL, CD-R/RW
1While the “Picture View” screen is displayed
Press [SUB MENU].
2Press [ 3,4 ] to select “Select Folder” and 
press [OK].
3Press [ 3,4 ] to select a folder and press 
[OK].
While playing
Press [STATUS] twice.
≥ It is also possible to display with the following procedures:
1 Press [SUB MENU].
2 Select “Status” with [ 3,4], and select [OK].
To exit, press [STATUS].
Rotate
Zoom out
To select the still pictures in another folder
To show the picture properties
\JPEG\DCIM001
Select Root folder
Change the Album folder to be accessed.
Press [OK] to confirm
e.g.,
PicturesFolder selection
CD(JPEG)
    001 
        002 
        003 
        004 
        005 
        006  
        007 
        
008        009 
        010 
      
    103 
        104 
        105
021216_0026   F  2/25
OK RETURN
e.g.
                                     
Photo     11/12/2009            Total        3/9
e.g., JPEG on DVD-RAM
Shooting date
DMPB100P-VQT2H71_eng.book  19 ページ  ２００９年１２月２４日　木曜日　午後４時５８分 
						

							VQ T2H71
20
Playing music
[CD] [MP3]
You can play generally available music CDs or MP3 files 
recorded onto a DVD-R/R DL and CD-R/RW.
(About structure of folders  >27, “Structure of folders that can 
be played in this unit”)
1Insert a disc ( >13).
“Music list” screen is displayed.
≥If the media containing data in different file formats is 
inserted, the file selection menu may be displayed. Press 
[3 ,4] to select “Play Music (MP3)” and press [OK].
2Press [ 3,4 ] to select the track and press 
[OK].
Play starts on the selected track.
≥ Playback for some discs may start automatically.
≥ You can use search and skip functions. ( >16 )
≥ The screen switches to Screen Saver mode if there is no 
operation for 2 minutes after starting playback. (Playback 
continues.) (If the media contains data in different file formats)
1
Press [FUNCTION MENU].
2 Press [ 3,4] to select “Menu” and press [OK].
3 Press [ 3,4] to select “Play Music (MP3)” and press [OK].
[MP3]
1While the “Music list” is displayed
Press [SUB MENU].
2Press [ 3,4 ] to select “Select Folder” and 
press [OK].
3Press [ 3,4 ] to select a folder and press 
[OK].
≥ You cannot select folders that contain no compatible tracks.
To return to the previous screen
Press [RETURN].
CD
Select an action or press [RETURN].OK
RETURN
SUB
MENU
Play Pictures (JPEG)Play Music (MP3)
e.g.,
 0.09  4.30
01
02
03
04
05
DIRECT NAVIGATORMusic listCD
No.
Track Name Play Time Track1
Track1 4min30sec 
3min41sec 
4min30sec 
3min11sec 
5min  2sec 
Track2
5 Tracks / Total Play Time 20min54sec
Track3
Track4
Track5
Play
RETURN
“ ” indicates the track currently playing.
e.g.,  [CD]
To switch from other menus to MP3 menu
Playing a track in another folder
DIRECT NAVIGATORSelect Folder
CD(MP3)
    001 My favorite
        002 Brazilian pops
        003 Chinese pops
        004 Czech pops
        005 Hungarian pops
        006 Liner notes
        007 Japanese pops
        
008 Mexican pops        009 Philippine pops
        010 Swedish pops
            011 Momoko
    012 Standard number
        013 Piano solo
        014Vocal
MP3 music   F  6/25
OK RETURN
Selected folder 
No. /Total folders
If the folder has no 
track, “– –” is 
displayed as folder 
number.
e.g.,
DMPB100P-VQT2H71_eng.book  20 ページ  ２００９年１２月２４日　木曜日　午後４時５８分