Panasonic DP 8020E User Manual

							11
Getting To KnowYour Machine
Manufacturer’s Name 
and Address Factory ID
• ATTENTION:Hot Surface• ATTENTION:Zone chauffée• ACHTUNG   :Heiße Oberfläche• ATENCION :Superficie caliente•                     •  FDA1992
■
 Laser Safety
■  Caution Label
LASER SAFETY
This unit employs a laser. Only qualified service personnel
should attempt to service this device due to possible eye
injury.
CAUTION:
USE OF CONTROLS, ADJUSTMENTS OR
PERFORMANCE PROCEDURES OTHER THAN THOSE
SPECIFIED HEREIN MAY RESULT IN HAZARDOUS
RADIATION EXPOSURE.
Precautions
Precautions
This product has a fluorescent lamp that contains a small amount of merc\
ury. It also contains lead in some
components.
Disposal of these materials may be regulated in your community due to en\
vironmental considerations.
For disposal or recycling information please contact your local authorit\
ies, or the Electronics Industries Alliance:

.
CAUTION
Downloaded From ManualsPrinter.com Manuals 
						

							12
Getting To Know Your Machine
Precautions
Installation
■The maximum power consumption is 1.3 kW.
A properly wired (grounded), dedicated, 12 A, 120 V AC outlet is required. Do not use an extension
cord.
The power cord on this machine must be used to disconnect the main power.
Please ensure that the machine is installed near a wall outlet and is ea\
sily accessible.
Supplies
■ Store the Toner and paper in cool areas with low humidity.
● Use high quality 16 - 24 lb (60 - 90  g/m2) (Sheet Bypass: 15 - 34 lb (55 - 133  g/m2)) paper.
●
For optimum performance, it is recommended that only Panasonic Brand sup\
plies are used in
the machine.
●
Certain types of transparency film may not be compatible and may damage \
your machine.
Consult with an authorized Panasonic dealer for advice regarding non-sta\
ndard paper types.
(Panasonic has tested “3M PP2500” transparency film and found it to be compatible.)
●
Panasonic recommends using high quality 16 - 24 lb (60 - 90  g/m
2) paper, using an inferior paper
may cause excessive paper curl, requiring you to empty out the Output Tray more often to avoid
paper jams.
■ Use of other than genuine Panasonic supplies can damage the machine. This may void the warranty
of the machine and supplies. Be sure to use only genuine Panasonic Toner designed for the machine.
■ The machine should not be installed in areas with the following conditio\
ns:
●
Extremely high or low temperature and humidity.
The machine should be installed under the following ambient conditions: Temperature: 50-86  °F (10 - 30  °C)
Relative humidity: 30-80 %
●
In areas with chemical fume concentration.
●
With unstable or uneven conditions (floors, etc.).
●
Direct exposure to sunlight or fluorescent light.
●
In areas of high dust concentration.
●
Directly in the air conditioning flow.
●
In areas of poor ventilation.
●
In areas with extreme vibration.
Illegal Copies
It is unlawful to make copies of certain documents.
Copying certain documents may be illegal in your country. Penalties of fines and/or imprisonment may
be imposed on those found guilty. The following are examples of items that may be illegal to copy in
your country.
● Currency
●
Bank notes and checks
●
Bank and government bonds and securities
●
Passports and identification cards
●
Copyright material or trademarks without the consent of the owner
●
Postage stamps and other negotiable instruments
This list is not inclusive and no liability is assumed for either its completeness or accuracy.
In case of doubt, contact your legal counsel.
Notice:
Install your machine near a supervised area to prevent illegal copies from being made.
Others
Panasonic is not responsible for data loss and any consequence caused by\
 computer virus infection
or external shocks.
Downloaded From ManualsPrinter.com Manuals 
						

							13
Getting To KnowYour Machine
Handling
■ Do not turn the Power Switch Off, or open the Front Cover during copying/printing.
■ Sleep/Shutdown Mode Notice
● The following functions will not work if the Sleep/Off Mode setting is set to the Shutdown mode.
When using any of the following functions, we recommend that you leave t\
he Sleep/Off Mode in the
initial factory default setting (Sleep mode).
-Turn OFF the Power Switch on the Right Side of the machine.
- Printer Function (Local Parallel Port and Network Connections)
- Internet Fax/Email Function
- Facsimile Function (Option)
When the LAN cable is not connected and DHCP Default is Yes
■ Key Operator Password
● The Initial Machine Modes can be checked or changed with the Function Mo\
des, however, these modes
require the Key Operator Password.
■ User Authentication
The User Authentication works for this machine under the management of the Window\
s Server. As a result,
users must be authenticated before they can use the functions of the machine (copying, faxing, scanning,
and printing). The supported authentication protocol is NTLM v2.
Users
- Users login to this machine using their Windows account (user name and \
password).
System Administrator
- The system administrator can manage user account by using Windows Server.
- User authentication can be set independently for each function (copying, faxing, scanning, and printing).
■ Dept. (Departmental) Code
When the Department Counter function is set up, the Dept. (Department) Code input screen is displayed on
the LCD Display. A registered Department Code (1 to 8- digit) is required to gain access\
 to each secured
function, or the secured Copy/Fax/Scanner function(s) cannot be used. \
Please consult with the Key Operator
regarding the Department Code(s) for the desired function.
Procedures  :
 1  Input a registered department code (1 to 8-digit).
 2  Press the SET or START key.
■ Maximum Copies Limitation
After setting the maximum allowed number of copies for each department, \
consult with your Key Operator
when the total copy count reaches the designated limit and the “DEPT.MAXIMUM COPIES HAS BEEN
REACHED” message appears on the LCD.
■ Power Switch
If you are not going to use the copier for long periods of time, turn OF\
F the Power Switch on the Right Side of
the machine.
If the Hard Disk Drive Unit (DA-HD18) is installed, to prevent a Scan \
Disk Function from being performed
(similar to Windows OS when the power is abruptly interrupted), it is \
important to follow the step sequence
below when turning OFF the Power Switch on the machine.
1. If the machine is in the “ENERGY SAVER (Shutdown Mode)” you may turn the Power Switch on the Right
Side of the machine to the OFF position. If it is not in the “ENERGY SAVER (Shutdown Mode)”, continue
to step 2 below.
2. Press “FUNCTION” and “ENERGY SAVER” keys simultaneously first. The Energy Saver Key will light.
3. Turn the Power Switch on the Right Side of the machine to the OFF positio\
n.
■ Auto Reset Time
As the initial setting for Auto Reset Time is 1 minute, the selected operation mode goes back to default
operation mode after 1 minute. If you wish to change the Auto Reset Time, consult with your Key Operator.
Downloaded From ManualsPrinter.com Manuals 
						

							14
Getting To Know Your Machine
INVINVLT RLGLLDR
LTR
LDR INV
LTR
LGL INV
LTR
INV
INV-R
LTR-R LGL
LDR
W idth Guides
Face Down
Until it stops
Upper Limit Guides
Until it stops
Sheet Bypass
PUSH
Paper Tray
Max Level
Indicator
Paper Tray
∗
∗ ∗
∗
∗Hold the guides by the center when
adjusting the width
Operation Chart
If set to other
function mode
(DP-8020E/8020P
only)
F ace Up
A
B
C
From
ADF/i-ADF
(Option)
From
Platen Face Down
●If the original is not positioned
properly, a portion of the original
may not be copied.
● For originals smaller than Invoice
size, position the original within
the Invoice area and select
Invoice.
or
● Adding Paper (Paper Tray)
The following steps are for Paper Tray-1, use the same procedures for other optional Paper Trays.
●  Adding Paper (Sheet Bypass)
Copying on Special Paper, etc. Load Paper: Face Up
Paper Weight: 16 - 24 lb (60 - 90 
g/m2)
Paper Capacity: 550 Sheets (20 lb (80  g/m2))
Adjust the width guides.
Incorrect adjustment may cause the
paper to wrinkle, misfed, or skew.
Original Guides
■  Quick Operation Chart
NOTE:
To  change the paper size, refer to
page 62.
1
123
Adding PaperT urn the Power
Switch to the
ON position
Original Guides ∗
∗ ∗
∗
∗
Adjust to the
originals width
T ray
(Max. 50 Letter
size originals)
INV: Invoice, LTR: Letter
LGL: Legal, LDR: Ledger
4
4Load Paper
(Do not exceed limit guides)
Paper Weight: 15-34 lb (55 - 133  g/m2)
Paper Capacity: 50 sheets/20 lb (80  g/m2)
To  add paper to the Sheet Bypass,
remove the leftover paper from the
tray, and align it with the additional
paper, then load them together onto
the tray.
NOTE: Load the paper properly, and ensure
that it does not exceed the Max. Level
indicator.
2
123
(ON)
(OFF)
Downloaded From ManualsPrinter.com Manuals 
						

							15
Getting To KnowYour Machine
Reduction/
Enlargement
only
■  Problem Solving
34
Number of
Copies
(Max. 999)
5
Select desired settings
(See pages 24-51)
Interrupt
(See page 48)
Sort
(See page 42) Zoom Mode   (See page 25)
Adding Paper
Replacing Toner Bottle/Toner Waste Container (See page 16)
Checking Toner (See below)Removing Misfed Paper
(See page 16)
U## (User Error Code) (See page 20)
J## (Jam Error Code) (See page 21)
E## (Machine Error Code) (Call your Service provider)
REPLACE DRUM UNIT (Call your Service provider)
LTR->INV [INV ]
ZOOM: 65% COPIES:001LTR->LTR [LTR ]
ZOOM:100% COPIES:001
2 Page Copy
(See page 34)
N in 1
(See page 32) Erase
(See page 38)
Effects
(See page 40)
Double
Exposure
(See page 36)
2-Sided/Original
      Copy
(See pages 26-31)
2-Sided Copy:
DP-8020E onlyT
ype of
Original
(See page 25) Manual
Exposure
From
Platen only
●
 T oner Level Check Operation
When CHECKING TONER PLEASE WAIT message appears, the machine is checking the toner level, and no
operation through control panel is accepted.
●  Memory Full
If the memory overflows while scanning originals, the message “MEMORY FULL CONTINUE? 1:YES 2:NO”
will appear on the LCD. If this occurs, follow the instructions on the L\
CD.
If this occurs frequently, adding optional memory is recommended, consult with an authorized Pana\
sonic dealer.
Downloaded From ManualsPrinter.com Manuals 
						

							16
Getting To Know Your Machine
Misfed Paper
● Removing Misfed Paper (Paper Transport/Fusing Area) (J01, J30, J31, J33, J45, J48, J95)
REMOVE MISFED PAPER
J48
Left Cover
Misfed Paper
Lift Upward and Pull Out
Paper Tray
Jam RemovalKnobLeft Cover
Corona Cleaner
Toner Bottle (New)
Toner Waste  Container
Front Cover
7
Operation Chart
■  Problem Solving
●  Removing Misfed Paper (Paper Exit Area) (J46)
● Replacing Toner Bottle/Toner Waste Container
12
REMOVE MISFED PAPER
J46
ATTENTION
● For optimum copy quality
use the recommended
Panasonic Toner. Store
Toner Bottle  in a cool
dark place. Do not unseal
the Toner Bottle unless
you are ready to use it.
Shake it well
6
NOTE:
Do not reuse the toner from the
Toner Waste Container.
12
12
65
Slide the Corona Cleaner in and out, 3
or 4 times slowly, then return the Corona
Cleaner Handle to the original position.
(Ex.)
(Ex.)
A TTENTION
● Do not scratch or touch the
surface of the OPC Drum
(Green) with bare hands.
The OPC Drum is sensitive
to light. To prevent optical
exposure problems, do not
expose the OPC Drum to
direct sunlight or bright light.
Downloaded From ManualsPrinter.com Manuals 
						

							17
Getting To KnowYour Machine
Toner Waste 
Container (New)
Cap
Toner Waste Container
Paper Tray
Lift Upward and 
insert the TrayLeft Cover
Heat Roller Cover
Jam Removal Knob
Misfed Paper
Left Cover
Misfed Paper
Corona Cleaner Handle
Toner Bottle (New)
Toner Bottle (New)
T oner Bottle (Empty)
4
6
3
5
8910
5
87
4
43
Close the Front Cover .
To
Release
To
Lock
3
Downloaded From ManualsPrinter.com Manuals 
						

							18
Getting To Know Your Machine
Paper Tray
Misfed PaperFeed Cover
ADF TrayExit Unit
Misfed PaperADF Cover
Misfed PaperADF Cover
Operation Chart
■  Problem Solving
●  Removing Misfed Paper (ADF: Option for DP-8020E/8020P/8016P) (J70, J\
71, J79, J92, J93)
12
REMOVE MISFED PAPER
J70
● Removing Misfed Paper (i-ADF: Option for DP-8020E) (J70, J71, J72, J\
73, J76, J78, J79, J92, J93)
REMOVE MISFED PAPER
J70
67
● Removing Misfed Paper (2nd/3rd/4th Paper Tray: Option)
(J02, J03, J04, J07, J08, J09, J12, J13, J14, J22, J23, J24)
REMOVE MISFED PAPER J02
Feed Cover
Lift Upward 
and insert 
the Cover
12
67
12
(Ex.) (Ex.)
(Ex.)
Downloaded From ManualsPrinter.com Manuals 
						

							19
Getting To KnowYour Machine
Misfed Paper
Misfed Paper
Lift Upward and Pull OutP aper Tray
1
2
Misfed Paper
Misfed Paper
Exit UnitADF Tray
ADF CoverMisfed Paper
ADF
34
5
6
6
34
89
534
ADF Cover
10
Downloaded From ManualsPrinter.com Manuals 
						

							20
Getting To Know Your Machine
Code Check PointsU20 ADF Cover is open.
U21 ADF/i-ADF was opened while scanning from
ADF/i-ADF.
U25 Toner hardened inside the Toner Bottle. Remove
the Toner Bottle, and shake it well.
U90 Battery requires replacement.
(See page 80)
Misfed PaperLeft Cover
■  Problem Solving
●  Removing Misfed Paper (J19, J32, J82, J85, J87: ADU for DP-8020E only)
12
REMOVE MISFED PAPER
J82
EX.
Code Check Points
U01 Front and/or Left Cover is open.
U07 Feed Cover is open. (See page 18)
U13 Low Toner, or Out of Toner.
U14 Toner Waste Container is full.
U15 Toner Waste Container is incorrectly installed.
U16 Developer Unit is incorrectly installed.
Call your Service Provider.
● User Error Codes (U Code)
U20
U21
U90
U01
U13
U14
U15
U16
U25
U07
Operation Chart
Downloaded From ManualsPrinter.com Manuals