Home > Panasonic > Video Recorder > Panasonic Dvd Vcr Deck Pv D4762 Operating Instructions

Panasonic Dvd Vcr Deck Pv D4762 Operating Instructions

    Download as PDF Print this page Share this page

    Have a look at the manual Panasonic Dvd Vcr Deck Pv D4762 Operating Instructions online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							31
      Playback
    When  playing  back  recording  which  have  been
    marked using  feature, you can
    either  set  VCR  to  automatically  advance  through
    marked commercial blocks, or set it so that
    commercials  are  only  skipped  on  your  command.
    AUTO :VCR  will  automatically  advance  through
    marked  commercial  blocks  recorded  on  the
    tape  and  then  resume  playback.
    MANUAL :VCR  will  advance  through  commercials  only
    when  CA/ZERO  is  pressed.  Playback  will
    resume  when  the  end  mark  of  a  commercial
    block  is  found,  or  a  new  recording  or  blank
    portion  is  detected,  or  after  8  minutes.
    • The  selection  mode  in  step  3  remains  set  unless  there  is  a  power  outage  in  which  case  the
    original  factory  setting  will  be  restored.
    • If  playback  is  started  in  the  middle  of  a  commercial,  only  a  single  commercial  is  shown,  or  an
    individual  commercial  is  longer  than  1  minute,  a  commercial  may  not  be  skipped.
    Press  FF  to  quickly  advance  through  the  commercial.
    • Part  of  a  recorded  program  may  be  skipped  over  if  the  program  portion  between  commercials
    is  less  than  1  minute  or  there  are  frequent  dark  and  quiet  scenes  during  the  program.  To  view
    the  portion  of  tape  being  incorrectly  skipped,  press  PLAY  while  the  VCR  is  skipping,  reverse
    the tape to a point just prior to where the skipping began and press PLAY again. This time the
    group will not be automatically skipped. Automatic skipping will be re-enabled when the end of
    the  marked  group  is  detected.
    4
    Press ACTION twice
    to return to normal screen.
    PLAY
    *Important:If a remote control button does not work when pressed, press
    the VCR button on the remote and try the button again.
     and are
    registered  trademarks  of  SRT,  Inc.
    A  Jerry  lggulden  invention  licensed
    in  association  with  Arthur
    D.  Little  Enterprises,  Inc.
    U.S.Pat.  No.  5,333,091;
    5,692,093;  5,696,866
    other  patents  pending
    Notes
    VCR
      Operation
    SETNUMBER
    keys
    SELECT 
    ACTION
    CA/ZERO
    Press 
    to select “SET UP
    COMMERCIAL ADV.,”
    and press SET to
    display.
    Press 
    to select “C/A
    PLAYBACK,”
    and press SET to set
    “AUTO” or “MANUAL”.
    2
    31
    Press  ACTION
    to display MENU.
    SELECT :              EXIT          : ACTION    SET:SET
                    MENU
    SET  UP  VCR
    SET  CLOCK
    SET  UP  CHANNEL
    SET  UP  C
    OMMERC I AL  ADV.  
    IDIOMA/LANGUE : ENGL I SH
    VCR’S  OUTPUT  CH:3
    SELECT :              SET : SET 
    EXIT      : ACT I ON     
      SET  UP  COMMERCIAL  ADV.
    C/A  RECORD            :ON
    C/A  PLAYBACK        :AUTO
    FF 
    						
    							32For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
    Tape Operation (continued)
    The  most  commonly  asked  questions  about   are  answered  below.
    Question
    How  fast  does  the  VCR  advance
    through  commercials?
    Are  commercials  advanced  through  only
    when  I  playback  a  recording?
    Are  commercials  still  recorded  on  the
    tape  in  case  I  choose  to  view  them
    sometime?
    Does 
      work  in
    all  recording  speeds?
    Does  the  VCR  advance  through
    commercials  each  time  I  playback  tapes
    which  were  recorded  using
    ?
    After  marking  commercials,  does  the
    VCR stop at the end of the tape, or
    rewind to the beginning?
    Can  I  play  my 
    recordings  in  non-
      VCRs?
    Does  the  marking  process  interfere  with
    other  programmed  recordings?
    What happens if I cancel the marking in
    progress  so  I  can  use  the  VCR?
    What  if  part  of  my  program  is  advanced
    through  along  with  the  commercials?
    Answer
    The  VCR  advances  through  a  3-minute  commercial
    block  in  about  8  to  12  seconds  if  the  tape  speed  is
    SLP.  In  SP,  it  takes  about  25  to  35  seconds.
    Yes.  The  commercials  are  not  marked  until  after  the
    recording  is  finished.
    Yes. By setting the C/A PLAYBACK to MANUAL (see
    page  31),  you  can  view  or  advance  through
    commercials  as  desired.
    Yes. 
     works in SP, LP, and
    SLP.
    Yes.  As  long  as  C/A  PLAYBACK  is  set  to  AUTO  (see
    page  31),  the  VCR  should  advance  through
    commercials  each  time  the  tape  is  played  back.
    The  tape  stops  at  the  end  of  the  recording  so  that
    any  additional  timer  recordings  can  be  performed.
    Yes. 
      marked  recordings  will
    play in non-
     VCRs, but
    commercials  will  not  be  advanced  through.
    No.  If  the  interval  between  2  or  more  timer  programs
    is  not  sufficient  to  mark  the  recording,  marking  will  be
    done  after  all  recordings  are  complete  and  the  power
    goes  off.
    Marking  will  be  resumed  when  the  VCR's  power  is
    turned  off  as  long  as  the  tape  has  not  been  ejected.
    Please see the 3rd note on page 31.
    Additional  Notes:
    • Because  of  the  various  ways  in  which  commercials  are  broadcast,  the  VCR  may  not  be  able
    to  recognize  all  commercials.
    • If a timer recording is scheduled for the middle of the night, please be aware that the VCR will
    make  some  noise  as  it  rewinds  and  fast  forwards  the  tape  while  marking  commercials.
      and   are  registered  trademarks  of  SRT,  Inc.
    A  Jerry  lggulden  invention  licensed  in  association  with  Arthur  D.  Little  Enterprises,  Inc.
    U.S.Pat.  No.  5,333,091;
    5,692,093;  5,696,866
    other  patents  pending 
    						
    							33
      helps  you  locate  certain
    parts  of  prerecorded  movies  (rented  or
    purchased). The feature works in two ways.
    • You can go to the beginning of the movie.
    •  You  can  skip  from  one  preview  to  the  next.
     works only on tapes
    recorded in SP speed with the record tab
    removed.
    Insert a tape
    without record tab.
    Press SEARCH/ M/A SKIP* three times to
    display MOVIE ADVANCE.
    Select “GO TO START MOVIE,” if you want
    to  advance  directly  to  beginning  of  the
    movie.
    ➛ ➛➛ ➛
    ➛continue with step 4.
    Select “GO TO PREVIEW,” if you want to
    view the first (next) preview.
    ➛ ➛➛ ➛
    ➛go to “To Search for Preview” at right.
    Press  FF
    to start searching.
    • To  cancel,
    press  STOP.
    Press  PLAY
    to start playback.
    When the movie is found...
    • To  cancel,
    press  STOP.
    1
    2Start preview searching.
    When a preview is detected, VCR
    will start playback.
    To Search for Preview.
    Start next preview searching. 1) In step 3 at left, select “GO
    TO PREVIEW.”
    2)Press FF.
    Press SEARCH/ M/A SKIP.
    • To  cancel, press  STOP.
    You can override the operation of SEARCH FOR
    PREVIEWS mode by pressing SEARCH/ M/A
    SKIP during tape searching.
     works by searching
    the tape past each preview and then reversing
    back  to  the  start  of  the  detected  preview.
    While the tape is reversing back, if SEARCH/ M/
    A SKIP is pressed, 
     will
    begin searching for the next preview.
    While searching for the next preview, if you see
    the start of a preview which you wish to watch,
    press SEARCH/ M/A SKIP and
     will immediately
    reverse  back  to  the  start  of  that  preview,
    instead of searching further past the preview
    start point. Once the VCR is playing a preview,
    press SEARCH/ M/A SKIP to advance to the
    next preview, long commercial or the start of
    the movie (whichever is next).
    • If  you  want  to  playback, press  PLAY.
    2
    3 1
    4
    Press   to  select
    “GO TO START
    MOVIE” or “GO TO
    PREVIEW.”
    5
    *Important:If a remote control button does not work when pressed, press
    the VCR button on the remote and try the button again.
    Ready Checklist
    All  connections  are  made.
    One  time  Setup  completed.
    VCR is plugged in.
    TV  is  turned  on  and  set  to  CH3,  4
    or Video on TV.
    GO  TO  START  MOVIE
    GO  TO  PREVIEW
    SEARCH  START : FF
    SELECT               :
    EXIT     :
     SEARCH  M/A  SK I P MOVIE  ADVANCE
    SEARCHING  FOR  START 
    OF  MOVIE
    CANCEL     :
     STOP MOVIE  ADVANCE
    THE  MOVIE  IS  READY 
    START     :
     PLAY  
    CANCEL     :
     STOP MOVIE  ADVANCE
    VCR
      Operation
    SETSTOP
    SELECT 
    SEARCH/
    M/A SKIP
    PLAY 
    						
    							34For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
    Index Search
    Note
    • If  Index  Search  is  started  very  close  to  an
    index  mark,  that  index  mark  may  not  be
    counted  in  the  search.
    1
    2
    Tape  Operation
    Search  System
    For  each  recording,  an  invisible  index  mark  is  placed  on  the  tape.  A  program  index  and
    information are also included for timer recordings. These marks are used to access or
    scan  recordings.
    1
    Program End Search
    2
    Fig. 1
    Fig. 2
    Fig. 3
    Note
    Locates  end  point  of  recording  for  continuity.
    Examples of Program End Search.
    If  search  exceeds
    a  few  seconds  in
    BLANK  area.
    ➛ ➛➛ ➛
    ➛search continues 7 sec. past end point,
    ➛ ➛➛ ➛
    ➛tape rewinds to 10 sec. before end point,
    ➛ ➛➛ ➛
    ➛tape plays to end point and stops. Upon locating end point,
    • If  Program  End  Search  is  started  very  close  to
    an  index  mark,  that  mark  may  be  skipped  over.
                             
         PROGRAM END SEARCH
    SEARCH START : FF
    EXIT     :SEARCH
    Program 2 or BLANK Program 1 
    the current tape position 
    Press SEARCH button
    FF
    INDEX
    End Point
    Program  2 Program 1 the current tape position 
    Press SEARCH button
    INDEXINDEX BLANK BLANK
    FFEnd Point
    Program  2 Program 1 
    the current tape position 
    Press SEARCH button
    BLANKINDEX
    FFEnd Point
                       
                INDEX   SEARCH   ENTER   INDEX  NUMBER  :1USING   1- 9 KEYS
    FORWARD  SEARCH :FF
    REVERSE  SEARCH :REW
    NEXT     :SEARCH/ M/AEXIT     :STOP
               INDEX  SEARCH
    FORWARD SEARCH  : FF
    REVERSE SEARCH  : REW      
    Press  SEARCH/
    M/A SKIP*
    to  display  SEARCH
    in Stop or Play
    mode,  and  then
    press  NUMBER
    keys
    to  select  recording
    number.
    • To  calculate
    number,  see  below.
    Press FF/SLOW+
    or REW/SLOW- on
    the remote to start
    search.Press SEARCH/ M/A SKIP twice
    to display SEARCH in Stop or Play
    mode.
    Press FF/SLOW+
    on the remote to
    start PROGRAM
    END  SEARCH.• To  cancel, press
    PLAY or STOP.
    Play  begins  at
    search  end.
    To  search  forward
    or back 1 index,
    press FF/SLOW+ or
    REW/SLOW- on the
    remote  while
    screen left is
    displayed  (10  sec.).
    • To  cancel, press
    PLAY or STOP.
     To Calculate Index Number
    Example  1:
    To  go  to  rec.  2  from  rec.  4,  enter  3  and  press  REW.
    Example  2:To  go  to  rec.  6  from  rec.  2,  enter  4  and  press  FF.
    NOTE: 
      indicates  start  points  of  each  recording.
    6157234
    17534 62 
    						
    							35
     Auto Play
    Insert a tape ➛ Power comes on,
    ➛ Play starts if no record tab
    (see p. 6).
     Auto Rewind
    Play
    Fast Forward
     Play Auto Eject
    (Repeat Play must be off)
    Play 
    ➛  ➛ ➛  ➛ 
    ➛ Tape end ➛  ➛ ➛  ➛ 
    ➛ Rewind
    ➛  ➛ ➛  ➛ 
    ➛ Tape ejects if no record tab
    Auto  Operation  Functions
    *Important:If a remote control button does not work when pressed,
    press the VCR button on the remote and try the button again.
    REW/SLOW-
    FF/SLOW+ PLAY
    SEARCH/
    M/A SKIP
    NUMBER
    keys
    CA/ZERO
    STOP
    VCR
      Operation
    ➛ Tape end ➛ Rewind
    Zero Search
    To  quickly  return  to  a  specified  tape  location.
    Continue  to  record,  playback  etc.
    Press STOP.
    • DECK will go into FF or REW mode and stop
    at the last point the Counter was set to 0:00:00.
    5 4 3 2 1
    PLAY       1 2 : 0 0AM 0 : 0 0 : 0 0 SP
    Press  DISPLAY during  play
    to  display  Counter.
    Press  COUNTER  RESET
    at  desired  position to  reset
    to “0:00:00”.
    Press CA/ZERO in Stop
    mode to start Zero Search.
    REW        1 2 : 3 0AM          CH  02 0 : 30 : 30 SP
    STOP       1 2 : 3 1AM          CH  02 0 : 0 0 : 0 0 SP
    COUNTER
    RESET DISPLAY 
    						
    							36For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
    Tape Operation (continued)
    Repeat Play
    Set  to  playback  a  recording  over  and  over.
    32 1
    SELECT :              EXIT          : ACTION    SET:SET
                    MENU
    SET  UP  VCR
    SET  CLOCK
    SET  UP  CHANNEL
    SET  UP  C
    OMMERC I AL  ADV.  
    IDIOMA/LANGUE : ENGL I SH
    VCR’S  OUTPUT  CH:3
    Press  ACTION*
    to display MENU.
    Press 
    to select “SET UP VCR,” and
    press SET.
    • Play  repeats  at  tape  end  or  if  unrecorded  portion
    over  30  sec.  is  detected.
    Press ACTION twice
    to return to normal screen.
    ACTION
    SET4
    Press 
    to select “REPEAT PLAY,”
    and press SET
    to set “ON” or “OFF.”REPEATREPEAT  PLAY                   : OFFREMOTE  WARN I NG            : ONAUTO  SHUT-OFF               : OFF
    SELE
    CT :                 SET: SETEND       : ACT I ON     
       SET  UP  VCR  
    SELECT 
    Note
    • For repeat play in DVD mode, see page 46. 
    						
    							37
    SELECT :              EXIT          : ACTION    SET:SET
                    MENU
    SET  UP  VCR
    SET  CLOCK
    SET  UP  CHANNEL
    SET  UP  C
    OMMERC I AL  ADV.  
    IDIOMA/LANGUE : ENGL I SH
    VCR’S  OUTPUT  CH:3
    ACTION
    SET
    Special VCR  Features
    SELECT 
    *Important:If a remote control button does not work
    when pressed,  press the VCR button
    on the remote and try the button again.
    When  set  to  ON,  all  operations
    except  for  timer  record  and  tape
    eject  are  prohibited.  Useful  for
    households  with  small  children.
    VCR Lock Feature
    VCR  LOCK  ACT I VATED
    VCR  LOCK  OFF
    • VCR  Lock  cancels  in  24  hours  if
    clock  is  set.
    To turn off, repeat above. To turn on, hold down REC o n
    DECK in Stop mode with no
    tape inserted for 7 seconds.
    (Please  ignore  “NO  CASSETTE”
    warning.)
    REC
    SELECT :              EXIT          : ACTION    SET:SET
                    MENU
    SET  UP  VCR
    SET  CLOCK
    SET  UP  CHANNEL
    SET  UP  C
    OMMERC I AL  ADV.  
    IDIOMA/LANGUE : ENGL I SH
    VCR’S  OUTPUT  CH:3
    VCR
      Operation
    Weak Signal Display Feature
    When  “ON,”  picture  is  displayed  regardless  of  signal
    strength.
    • ON: Picture  is  displayed  regardless  of  signal
    condition,  and  may  not  always  be  clearly  visible.
    OFF:Screen  turns  solid  blue  when  signal  is  weak  or
    non-existent.
    • Selecting  ON  has  no  effect  on  connected  equipment
    with  blue  back  feature.
    Press ACTION twice
    to return to normal screen.
    4 3 2
    Press 
    to select “SET UP
    CHANNEL,”  and
    press SET.
    Press 
    to select “WEAK SIGNAL
    DISPLAY,” and
    press SET
    to set “ON” or “OFF.”
    1Press  ACTION
    to display MENU.
    Auto  Shut-Off  Feature
    The  power  shuts  off  at  a  preset  time.
    3 1
    4
    Press 
    to select “AUTO SHUT-OFF.”
    Press SET  repeatedly  to
    change shutoff time as
    shown  below.
    Press ACTION twice
    to return to normal screen. Press  ACTION
    to display MENU.
    2
    Press 
    to select “SET UP VCR,” and
    press SET.
    • The  shut-off  countdown  will  not
    function  during  Play  or  Record.
    Note
    SELECT :                 SET: SETEXIT       : ACT I ON    
    ANTENNA  :   CABLE
    AUTO   SETWEAK  S I GNAL  D I SPLAY:OFF
    SET  UP  CHANNEL
    REPEAT  PLAY                : OFFREMOTE  WARN I NG         : ONAUTO  SHUT-OFF            : OFF
    SELE
    CT :                   SET: SETEXIT       : ACT I ON   
    SET  UP  VCR
    OFF
    2 Hours
    6 Hours4 Hours 
    						
    							38For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
    Special VCR  Features  (continued)
    INPUT
    ACTION
    SET
    TAPE
    POSITION
    SELECT 
    If  Multi-brand  feature  is  used  (p.  28),  and  this  feature  is
    set  to  on,  a  warning  appears  whenever  an  invalid  key
    is  pressed  in  TV,  DSS  or  CABLE  mode.
    4 31
    • If  “OFF,”  remote  warning  will  not  appear
    when  invalid  key  is  pressed.
    Press  ACTION*
    to display MENU.
    Press 
    to select
    “REMOTE WARNING,” and
    press SET
    to set “ON” or “OFF.”
    Press ACTION twice
    to return to normal screen.
    Remote Warning Feature
    2
    Press 
    to select “SET UP VCR,”
    and
    press SET.
    SELECT :              EXIT          : ACTION    SET:SET
                    MENU
    SET  UP  VCR
    SET  CLOCK
    SET  UP  CHANNEL
    SET  UP  C
    OMMERC I AL  ADV.  
    IDIOMA/LANGUE : ENGL I SH
    VCR’S  OUTPUT  CH:3
    REPEAT  PLAY                   :  OFFREMOTE  WARN I NG            :  ONAUTO  SHUT-OFF               :  OFF
    SELE
    CT :                 SET: SETEXIT       : ACT I ON    
    SET  UP  VCR
    *Important:If a remote control button does not work
    when pressed,  press the VCR button
    on the remote and try the button again.
    PAUSE/
    STILLSTOP
    REC
    To find out the present tape position and amount of tape remaining.
    Tape  position  is  displayed  for  VHS-C  Cassettes  type,  tapes
    under  30  minutes,  and  some  other  tapes,  but  the  position  is
    not  correct.
    • Tape remaining time display may not be
    precise.
    1
    BEG I N                END
                                                    SP
                                     R 120 M
     I  N.
    • “DETECTING  TAPE  POSITION”  is  displayed
    only  when  a  cassette  is  first  inserted,  and  it
    takes  several  seconds  for  correct  tape
    position  to  appear.
    Tape Position and Tape Status Feature
    Press TAPE POSITION
    to return to normal screen.
    2
    • The  present  tape  position  indication  and
    amount  of  tape  remaining  (according  to
    tape  speed)  is  displayed.
    DETECTING   TAPE   POSITION
    Press TAPE POSITION
    to detect current tape position.
    This  function  cannot  display  exact  amount  of  tape  remaining  for
    tapes  30  minutes  or  less,  or  for  tapes  over  120  minutes  in  length.
    Note 
    						
    							39
    Copying Your Tapes (Dubbing)
    1Insert a pre-recorded tape.
    2
    Insert a blank tape with record tab.
    Press REC, then PAUSE/STILL
    immediately  to  enter  REC/PAUSE
    mode.
    3
    Press INPUT to set DECK Input mode to
    LINE for Video Input.
    (See  “Selecting  the  Input  Mode”  below.)
    4
    Press PLAY to start dubbing.
    Playing  VCR  starts  playback.Press PAUSE/STILL to start dubbing.
    DECK  starts  recording.
    Press STOP to stop dubbing.
    Caution:• Unauthorized  exchanging  and/or  copying  of  copyrighted  recordings  may  be
    copyright  infringement.
    • Please  note  that  some  tapes  cannot  be  dubbed  on  DECK.  Also,  it  is  not
    possible  to  dub  DVD/  Video  CD/  CD  to  VHS  tapes  using  DECK.
    Playing  (Source)  VCRRecording  (Editing)  DECK
    5
    To Monitor Dubbing on  TV
    1Turn  TV  on  and  tune  to  the  Recording
    VCR  channel  (CH  3  or  CH  4).
    2Set  the  VCR/TV  Selector  on  DECK  to
    “VCR.”
    Note• Dubbing  tapes  protected  with  Copy
    Guard  will  have  poor  quality  results.
    Connection
    Press STOP to stop dubbing. Press PLAY, then PAUSE/STILL
    immediately  to  enter  PLAY/PAUSE
    mode.
    The  operation  of  steps  4  and  5  must  be  done  on  both
    playing  and  recording  VCRs  at  the  same  time.
    Connect VIDEO OUT terminal on Playing VCR to VIDEO IN terminal on DECK.
    To monitor the dubbing, also connect TV as shown.
    Connect “L” and “R” AUDIO OUT terminals on Playing VCR to “L” and “R”
    AUDIO IN terminals on DECK.
    In place of Playing VCR, you can use other equipment, such as a Camcorder.
    Simply  connect  the  unit’s  Audio/Video  outputs  to  DECK.
     Selecting the Input Mode
    Method  1:Press  INPUT  repeatedly.Channel Number 
    ↔ ↔↔ ↔
    ↔ LINE1 
    ↔ ↔↔ ↔
    ↔ LINE2Method  2:Press CH /.
    Display  will  change  as  below.
    Front of DECK
     VIDEO IN 2L-AUDIO  IN2-R
    (Audio/Video  In  Terminals
    on  the  front  of  DECK  are
    available)
    IN FROM ANT.
    OUT
     TO TV
    IN 1
    VHF/UHF
    OUT
    TV
    OUT
    VHF/
    UHF
    DVD/VCR DECK
     VIDEO
     AUDIO
    1L
    R
    VCR/ Camcorder (Hi-Fi)
     VIDEO
     AUDIOL
    R
    • “L1” or “L2” lights up on Multi Function Display
    (about 4 seconds) when LINE1 or LINE2 is selected.
    • LINE1:  For rear audio/video connection.
    LINE2:  For front audio/video connection.
    1
    2
    VCR
      Operation
    1
    23
    125
    LINE1(CABLE)69(TV)orLINE2Press
    Press 
    						
    							40For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
    AUDIO:3  ESP
    Dolby  Digital  3/2.1ch
    SELECT:  SET:SET
    Hola
    AUDIO:1  ENG
    Dolby  Digital  3/2.1ch
    SELECT
    :  SET:
    T:SET
    Hello
    ESPESP
    Te amoTe amo
    • If  after  several  presses  of  the  button  the  language  does  not
    change,  language  selection  is  not  offered  on  the  disc.
    • When  power  is  turned  on again  or  disc  is removed,  subtitles
    revert to initial setting language. If the initial language is not
    recorded  on  the  disc,  the  disc’s  priority  language  will  appear. You  can  select  a  different  subtitle  language  (if  offered)  than
    the  one  set  at  the  Settings  for  DVD  Operation.
    (See  p.  49.)
    Press 
    to  select  a  language.
    Press  (or  )
    to set.
    Press 
    to select “ON” or “OFF.”
    Subtitle Language (DVD only)
    • Display  disappears  after
    5  seconds.
    • When  no  subtitles  are  offered,
    “-” will be displayed instead of
    the  language  number.
    Press SUB TITLE*
    in  Play  mode  to  display
    the  subtitle  selection
    on-screen.
    ENG
    FRA
    DEU
    ITA
    ESP
    NLDEnglish
    French
    German
    Italian
    Spanish
    Dutch
    SVE
    NOR
    DAN
    POR
    RUS
    JPNSwedish
    Norwegian
    Danish
    Portuguese
    Russian
    Japanese
    CHI
    KOR
    MAL
    VIE
    THA
     ∗
    Chinese
    Korean
    Malay
    Vietnamese
    Thai
    Other
    [Subtitle language (No.)]
    [Audio sound track language (No.)]
    • Change  the  No.  by pressing ,
    and press SET.
    Ready  Checklist
    Please  read  “Basic  DVD  Operation”
    on p. 22.
    You  can  change  the  audio  soundtrack  language,  selected
    at the Settings for DVD Operation, to a different language
    if available. (See p. 49.)
    (This  operation  works  only  with  discs  on  which  multiple
    audio  soundtrack  languages  are  recorded.)
    Press AUDIOin Play mode to display the
    audio  selection  on-screen.
    Audio Soundtrack Language (DVD only)
    Audio attribute 1 type,
    sampling  frequency,  bit  No.  of
    the  disc.
    [Audio attribute 1 type, sampling
    frequency, bit No. of the disc (see
    p. 50.)]
    Disc  Operation
    1
    2
    1
    2
    Number  of  subtitle  language  being  played  back.
    Press 
    to  select  desired  language.
    Number  of  the  audio  soundtrack
    language  being  played  back.• If,  after  several  presses  of  the
    AUDIO  button  the  language  does  not
    change,  language  selection  is  not
    offered  on  the  disc.
    • When power is turned on again or
    disc  is  removed,  language  reverts  to
    initial setting. If this language is not
    recorded  on  the  disc,  the  language
    recorded  will  be  heard.
    LPCM
    Dolby DigitalDTS96KHz
    or
    48KHz
    1ch - 5.1ch
    1ch - 5.1ch16bit
    20bit
    24bitLinear PCM disc
    Dolby Digital disc
    DTS disc
    Notes
    Notes
    • Display  disappears  after
    5  seconds. 
    						
    All Panasonic manuals Comments (0)

    Related Manuals for Panasonic Dvd Vcr Deck Pv D4762 Operating Instructions