Panasonic Dvd Vcr Deck Pv D4763 Operating Instructions

11
VCRTIMER RECHi - FiDIGITDIGITAL
CDDVDMP3
WMA
AM
PMANGLE
REC         1 2 : 0 0AM0 : 25CH 02-0 : 1 2 : 3 4 SPSTEREOSAPMONO
VCR Status & Clock DisplaysBlank Tape/ No Video Signal
Indications
Whenever a blank section of a tape
comes up in Play mode, or when the
selected channel has no broadcast
signal with Weak Signal Display
Feature (p. 33) set to OFF, the TV
screen will turn solid blue.
Function Status
Rec Time Remaining
(OTR mode only,
see p. 21.)
Current Time
Channel
Tape Speed
(See p. 4.) Broadcast...

12For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Connections
1 Disconnect antenna or cable from TV
and connect to DECK.
WARNING
When using “Nut type” RF coaxial cables, tighten with
fingers only. Overtightening may damage terminals.
Basic Connections
Connect DECK and TV with an RF Coaxial Cable a (supplied) or an AV Cable b
(not supplied) as shown in the figure below.
If your TV has AUDIO and VIDEO IN terminals, connect them to DECK for higher...

13
You CannotYou Can
record and view
both scrambled
and unscrambled
channels if
additional
equipment is
added.
This connection
requires: two
converter boxes,
an A/B switch,
and a 2-way
splitter.view a channel
other than the
one selected
for any type of
recording.
do a Timer
recording of a
channel unless
you select it on
the Cable Box.IN FROM ANT.
OUT
 TO TV
IN 1
VHF/UHF
OUT
IN 2 IN 1
Cable Box
OUT IN OUT 2 OUT 1
2-Way Splitter
OUT
A/B Switch IN
  
      
  Connect With Two Cable Boxes
IN FROM...

14For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Connections (continued)
Audio Connections
Ready Checklist
Turn down the volume, then turn DECK, as well as other equipment to be connected,
off before proceeding with connection.
Do not block ventilation holes of any of the equipment and arrange them so that air can
circulate freely.
Read through the instructions before connecting other equipment.
Ensure that you observe the color coding when...

15
Enjoy the powerful movie theater and hall-like sound available with multiple
channel audio found on DVDs by connecting an amplifier and speakers.
There are two types of connection, digital and analog.
Caution for optical digital audio output connector:
When connecting an amplifier (with an Optical Digital Input Connector) which does not
contain the Dolby Digital or DTS decoder, be sure to select “PCM” at “Dolby Digital”
and “PCM” at “dts” of the Settings for DVD Operation “Audio Output” (see p. 54)....

16For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Before doing Initial Setup
Initial Setup for Basic Connections (Ready to Play)
Turn TV on.
See connections a RF Coaxial Cable Connection and b AV Cable Connection on page 12.

  Set TV to channel 3.

Set TV to VIDEO.
[DECK 
➛ ➛➛ ➛
➛ TV]
  Go to “Initial Setup (Ready to Play).” (See below.)
[Cable Box 
➛ ➛➛ ➛
➛ DECK 
➛ ➛➛ ➛
➛ TV], [DSS 
➛ ➛➛ ➛
➛ DECK 
➛ ➛➛ ➛
➛ TV]
  Turn on Cable Box and set it to...

17
*Important:If a remote control button does not work when pressed,
press the VCR button on the remote and try the button again.
Settings are made automatically.
When setup is done, this screen appears.
If “AUTO CLOCK SET IS INCOMPLETE”
appears, manually set clock. See below.
3
6 / 8/ 20 03 SUN    2 : 20PMDST : ONSETT I NG  :   CH   10
AUTO  CLOCK  SET
    
 COMPLETED
If Auto Clock Set was incomplete.
Press ACTION* on remote to display
CLOCK screen.
Press 
 to select the month and SET to
set. In the...

18For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
SELECT :              EXIT         : ACTION SET : SET
                MENU
SET  UP  VCR
SET  CLOCK
SET  UP  CHANNEL
SD  CARD  PLAYBACK
IDIOMA/LANGUE : ENGLISH
VCR’S OUTPUT CH:3
Clock
2)Press  to select
“MANUAL,” and press SET.
(For Auto Clock Set, select
“AUTO CLOCK SET.”)
3) Press 
 and  to
select, then set the date,
time, and DST (Daylight
Saving Time).
4) Press ACTION to 
startClock and exit this...

19
Add or Delete a Channel
To add channel:
Select channel with NUMBER keys
and press ADD/DLT.
To delete channel:
Select channel with CH 
/ or
NUMBER keys and press ADD/DLT.
CHANNEL  08  ADDED
CHANNEL  08  DELE TED
Time Zone Adjust
2)Press  to select
“TIME ZONE ADJUST,”
VCR’s Output
Channel
1) Press  to select
“VCR’S OUTPUT CH.,”
and press SET.
SELECT :                 EXIT         : ACTION SET : SET
               MENU
SET  UP  VCR
SET  CLOCK
SET  UP  CHANNEL
SD  CARD  PLAYBACK
IDIOMA/LANGUE : ENGLISH...

20For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Playback/ Record on a Tape
Insert a tape.21
Playback using DECK buttons
Press PLAY.
Multi Function Display
Press STOP/EJECT to stop
and/ or eject a tape.
Ready Checklist
All connections are made. (pp. 12 ~ 15)TV and DECK are plugged in.TV is on and tuned to CH 3, 4, or VIDEO.Remote is in VCR mode. (Press VCR.)
Insert a tape.
DECK power comes on. If Auto VCR/TV (see
p. 32) is set to “OFF,” press VCR/TV...