Panasonic E 37 V Dome Camera Operation Manual

							                                              
 36 
Parameter  Function  
Host Name  It is to set current host device name. It max supports 15 
characters.   
Ethernet Card Please select the Ethernet port. Default is wired.  
Please note you can modify the default Ethernet card if there is 
more than one card. . 
Please note the device needs to reboot to activate the new 
setup once you modify the default setup.  
Mode There are two modes: static mode and the DHCP mode. Select 
DHCP mode, it auto searches IP, and you cannot set IP/subnet 
mask/gateway. Select static mode, you must manually set 
IP/subnet mask/gateway.  
Mac Address  It is to display hose Mac address.  
IP Version  It is to select IP version. IPV4 or IPV6. 
You can access the IP address of these two version. 
IP Address  Please use the keyboard to input the corresponding number to 
modify the IP address and then set the corresponding subnet 
mask and the default gateway.  
Preferred DNS DNS IP address. 
Alternate DNS  Alternate DNS IP address.   
						

							                                              
 37 
Enable 
ARP/Ping set 
device IP 
address service.  
You can use ARP/Ping command to modify or set the device IP 
address if you know the device MAC address.  
Before the operation, please make sure the network camera 
and the PC in the same LAN. This function is on by default.  
You can refer to the steps listed below.  
Step 1: Get an IP address. Set the network camera and the PC 
in the same LAN. 
Step 2: Get the physical address from the label of the network 
camera. 
Step 3: Go to the Run interface and then input the following 
commands.  
arp  –s       
ping  –l  480  –t   
Such as：arp  -s  192.168.0.125  11-40-8c-18-10-11 
ping  -l  480  -t  192.168.0.125 
Step 4: Reboot the device.  
Step 5: You can see the setup is OK if you can see there are 
output information such as “Reply from 192.168.0.125 …” from 
the command output lines.  Now you can close the command 
line.  
Step 6: Open the browse and then input http://. 
Click the Enter button, you can access now.  
 
4.1.5 Connection  
4.1.5.1 Connection 
The connection interface is shown as in Figure 4-17. 
 
  
						

							                                              
 38 
 
Figure 4-17 
Please refer to the following sheet for detailed information.  
Parameter  Function  
Max 
connection  
It is the max Web connection for the same device. The value ranges from 1 
to 20. Default connection amount is 10. 
TCP port  Port range is 1025~65534. The default value is 37777. You can input the 
actual port number if necessary.  
UDP port  Port range is 1025~65534. The default value is 37778. You can input the 
actual port number if necessary. 
HTTP port  Port range is 1025~65524. The default value is 80. You can input the 
actual port number if necessary. 
RTSP port  The default value is 554. Please leave blank if use default. User uses 
QuickTime or VLC can play the following formats. BlackBerry can play 
too.  
 Real-time monitoring URL format, please require real-time RTSP 
media server, require channel no., bit stream type in URL. You may 
need username and password.  
 User uses BlackBerry need to set encode mode to H.264B, resolution 
to CIF and turn off audio.  
URL format is: 
rtsp://username:password@ip:port/cam/realmonitor?channel=1&subtype=0 
username/password/IP and port.  
The IP is device IP and the port default value is 554. You can leave it in 
blank if it is the default value.  
Follow standard RTP protocol and when encode mode is MJPEG, the max 
resolution only supports 2040*2040.  
 HTTPs 
Enable  
Check HTTPs enable, login as https://ip:port. Protect data. Default port is 
https://ip . It is disabled by default.  
HTTPs 
Port 
HTTPs communication port, range is 1025~65534, default is 443.  
Note: 
 0～1024, 37780～37880, 1900, 3800, 5000, 5050, 9999, 37776, 39999, 42323 are all special ports. 
User cannot modify them.  
 Avoid using default port value of other ports.  
  
						

							                                              
 39 
4.1.5.2 ONVIF 
ONVIF（Open Network Video Interface Forum），this standard describes network video mode, 
interface, data type and data interaction mode. ONVIF Standard’s aim is to achieve a network video 
frame agreement and makes the network video products (including video front-end, video equipment, 
etc.) from different manufacturers completely compatible.  
ONVIF function default is closed. 
 
 
Figure 4-18 
4.1.6 PPPoE 
The PPPoE interface is shown as in Figure 4-19. 
 
Input the PPPoE user name and password you get from the IPS (internet service provider) and enable 
PPPoE function. Please save current setup and then reboot the device to get the setup activated.  
Device connects to the internet via PPPoE after reboot. You can get the IP address in the WAN from 
the IP address column. When PPPoE is on, please disable UPnP to avoid influence on dial-up.  
When you Check PPPoE enable, please disable UPnP.  
Please note, you need to go to the IP address item to via the device current device information. 
You can access the client-end via this address.  
  
						

							                                              
 40 
 
 
Figure 4- 19 
4.1.7 DDNS 
The DDNS interface is shown as in Figure 4-20. 
The DDNS is to set to connect the various servers so that you can access the system via the server. 
Please go to the corresponding service website to apply a domain name and then access the system 
via the domain. It works even your IP address has changed. When the device connects to WLAN, you 
should disable UPnP.  
 
Figure 4-20  
						

							                                              
 41 
Please refer to the following sheet for detailed information.  
Parameter  Function  
Server Type You can select DDNS protocol from the dropdown list: CN99 
DDNS, NO-IP DDNS, Dyndns DDNS, QUICK DDNS, the QUICK 
DDNS function is realized according to the customized private 
protocol.  
Server Address DDNS server IP address 
CN99 DDNS 
Server address: www.3322.org 
NO-IP DDNS 
Server address: dynupdate.no-ip.com 
Dyndns DDNS 
Server address: members.dyndns.org 
QUICK DDNS 
Server address: www.quickddns.com  
Domain Name  Customized domain name by users 
Username The user name you input to log in the server. 
Password The password you input to log in the server 
Refresh Period  The refresh period of the connection between the device IP and 
the server, default is 10 minutes. 
 
The QUICK DDNS interface is shown as in Figure 4-21.  
 
Figure 4-21  
						

							                                              
 42 
 
Parameter  Function  
Server Type You can select QUICK DDNS protocol  
Server Address Under QUICK DDNS the default server address is “www.quickddns.com” 
Mode  Default is auto, manual is optional.  
Domain Name The default is “MAC address.quickddns.com” for both auto and manual, for manual 
users can set prefix by themselves.  
Test  It is to test if the domain name can be used or not. The parameter exists only when 
selecting “manual” in “Mode”.  
Username The user name you input to log in the server, optional.  
 
4.1.8 IP filter 
The IP filter interface is shown as in Figure 4-22. 
You can enable IP filter function so that some specified IP/MAC user can access the network camera.  
You can add IP address or IP address section.  
If you do not check the box here, it means there is on access limit.  
Here you can add IP address and MAC address. You must add these addresses before enabling the 
trusted sites.  
Please note: You must set MAC address in the same network segment.  
 
 
Figure 4-22 
  
						

							                                              
 43 
4.1.9 SMTP （e-mail) 
The SMTP interface is shown as in Figure 4-23. 
 
Figure 4-23 
Please refer to the following sheet for detailed information. 
Parameter  Function  
SMTP Server  Input server address and then enable this function.  
Port  Default value is 25. You can modify it if necessary. 
Anonymity  For the server supports the anonymity function. You can auto 
login anonymously. You do not need to input the user name, 
password and the sender information.   
User Name The user name of the sender email account. 
Password The password of sender email account. 
Sender Sender email address. 
Authentication 
(Encryption 
mode)  
You can select SSL, TLS or none.  
Title (Subject) Input email subject here.  
 
Attachment  System can send out the email of the snapshot picture once 
you check the box here.  
Mail receiver Input receiver email address here. Max three addresses. 
  
						

							                                              
 44 
Parameter  Function  
Interval  The send interval ranges from 0 to 3600 seconds. 0 means 
there is no interval. 
Please note system will not send out the email immediately 
when the alarm occurs. When the alarm, motion detection or 
the abnormity event activates the email, system sends out the 
email according to the interval you specified here. This 
function is very useful when there are too many emails 
activated by the abnormity events, which may result in heavy 
load for the email server. 
Health mail 
enable  
Please check the box here to enable this function.  
 
Email test  The system will automatically sent out a email once to test the 
connection is OK or not .Before the email test, please save 
the email setup information.  
 
4.1.10 UPnP 
It allows you to establish the mapping relationship between the LAN and the public network. 
Here you can also add, modify or remove UPnP item. For UPnP on different routers, you must disable 
UPnP function. See Figure 4-24. 
In the Windows OS, From Start->Control Panel->Add or remove programs. Click the “Add/Remove 
Windows Components” and then select the “Network Services” from the Windows Components Wizard.  
Click the Details button and then check the “Internet Gateway Device Discovery and Control client” and 
“UPnP User Interface”. Please click OK to begin installation.  
Enable UPnP from the Web. If your UPnP is enabled in the Windows OS, the network camera can auto 
detect it via the “My Network Places”. 
Under manual mode, you can modify external port. Under auto mode, select idle port for auto port 
mapping without user modification. 
  
						

							                                              
 45 
 
Figure 4-24 
 
4.1.11 Bonjour 
The Bonjour interface is shown as below. See Figure 4-25. 
Bonjour is based on the multicast DNS service from the Apple. The Bonjour device can automatically 
broadcast its service information and listen to the service information from other device. 
You can use the browse of the Bonjour service in the same LAN to search the network camera device 
and then access if you do not know the network camera information such as IP address.   
You can view the server name when the network camera is detected by the Bonjour. Please note the 
safari browse support this function. Click the “Display All Bookmarks: and open the Bonjour, system can 
auto detect the network camera of the Bonjour function in the LAN.