Panasonic Electronic Board UB-2815C, UB-2315C Operating Instructions

Precautions
11
Before You StartBatteryIf battery is used improperly, battery may leak, causing corrosion to the unit, or it may burst. 
To prevent this, always follow the precautions given below.
•Always insert battery with its polarity properly oriented.
•
If the battery has run out, remove it immediately and dispose of it according to local regulations.
Leaving drained battery may result in leakage.
•Do not disassemble battery or place it in a fire.
•Do not short battery.
 
CD-ROMTo prevent damage to...

Part Names and Functions
12
* This is a diagram of the UB-2815C.
UB-2315C is equipped with one board stopper and one board stopper lever.
Part Names and Functions
Scanner White Balance
Area
Control BoxBoard Stopper LeverBoard Stopper
Tr a y
Whiteboard White Balance
Area
Stand
Stand
Caster  
with Lock
Caster  
with Lock
CasterCaster
Fall-prevention  
Extension Leg
Fall-prevention  
Extension Leg
AC Inlet Power Cord
Battery Holder
Power SwitchOFF ON
Control Panel
USB Connector-A
for USB Flash 
Memory...

Part Names and Functions
13
Before You Start
Control Panel
NameDescription
Display
When in standby mode, the display shows the current status of the unit as follows:
•The time is shown on the top left corner of the display.
•The scanning mode is shown on the icons on the left side of the display.
•The destination for scanned images is show in the center of the display.
Mode Key
Press repeatedly to select the scanning mode. The selected mode will be indicated 
next to the icons on the left side of the...

Scanning
14
It is possible to output scanned images to a USB flash 
memory device, SD memory card, or external printer.
If multiple output devices are connected to this unit at 
the same time, the output destination will be selected 
in the following priority:
1. USB flash memory device
2. SD memory card
3. External Printer.
The current destination is shown on the display.
For information on scanning images using a 
computer, refer to “Computer Interfacing” on page 22.
Note
•When there is no appropriate...

Scanning
15
Using
1
Set the power switch to on ( I ).
•The scanner will move to the home position 
and stop.
2
Connect the USB flash memory device to 
“USB Connector-A for USB Flash Memory 
Device”.
•When the USB flash memory device is 
connected, a USB flash memory icon will 
blink on the display. Once the unit recognizes 
the device, the icon will stop blinking.
The display below is an example of the unit 
in standby mode.
Note
•You cannot use a USB flash memory device 
that is equipped with certain...

Scanning
16
1
Set the power switch to on ( I ).
•The scanner will move to the home position 
and stop.
2
Open the SD memory card cover and insert 
the SD memory card into the SD memory card 
slot until it is locked. Then close the SD 
memory card cover.
•The SD memory card icon is shown on the 
display.
The display below is an example of the unit 
in standby mode.
Note
•If an SD memory card has been formatted 
(ex. by the general formatting software of a 
computer), it oftentimes cannot be 
recognized by...

Scanning / Moving the Electronic Board
17
Using
1
Set the power switch to on ( I ).
•The scanner will move to the home position 
and stop.
2
Turn the external printer on and load the 
paper.
3
Connect the external printer to “USB 
Connector-A for Printer” with a USB cable.
•The printer icon is shown on the display.
The display below is an example of the unit 
in standby mode.
4
Press the Mode Key   to select the scanning 
mode.
5
Press the Multi-Copy Key   repeatedly to 
select the number of copies (1 to...

Rotating the Whiteboard
18
The whiteboard can be used on both sides.
•Rotate the whiteboard carefully and slowly. 
Otherwise, a finger can get caught or the whiteboard 
may strike the person resulting in injury.
•When rotating or fastening the whiteboard, be 
careful not to get your fingers caught between the 
whiteboard and the stoppers as this may result in 
injury.
•After rotating the whiteboard, make sure that it is 
correctly fastened with the board stoppers. 
Otherwise, the whiteboard may turn...

Setting the Unit
19
Using
The following settings can be made using the control 
panel.
It is possible to select whether the time that an image 
is scanned is displayed on the image.
1
Press the Set-up Key  .
•The set-up screen is displayed.
2
Press the Multi-Copy Key ( ) repeatedly to 
select   (On) or   (Off).
•When the scanning time display is set to 
off, the following screen is displayed.
3
Press the Mode Key ( ) to return to standby 
mode.It is possible to select the file format for outputting...

Setting the Unit
20
When images are scanned in full size mode, they are 
stretched and enlarged in order to utilize the entire 
space of a page. 
1
Press the Set-up Key  .
•The set-up screen is displayed.
2
Press the Set-up Key ( ) twice.
•Image size set-up is selected.
3
Press the Multi-Copy Key ( ) repeatedly to 
select   (Regular) or   (Full size).
4
Press the Mode Key ( ) to return to standby 
mode.It is possible to set the current time for the unit clock.
1
Press the Set-up Key  .
•The set-up screen...