Panasonic Electronic Board Ub 780bp Operating Instructions

							Included AccessoriesCheck that all of the following items are included with your elite Panaboard.
In the event that an item is missing, please contact your dealer.
List of AccessoriesUSB Cable
(5 m [16 ft. 4  7
/8  in.])1Software CD-ROM1AAA Battery (LR03)
(Disposable)1Electronic Pen1Penpoint
(Replacement)2
Operating Instructions
(For Basic Operations) (this document)
1
Warranty1
Note
•Stand is sold separately.
• Store the extra penpoint along with this operating manual.
• The warranty may not be included depending on country/area.
About Using the CD-ROM
To prevent damage to the CD-ROM:
• Do not touch or write on the surface of the disc.
• Do not leave the disc out of the protective case.
• Do not leave the disc in the direct sunlight or near heat sources.
• Do not place heavy objects on the disc case or drop the case.
• To clean the disc, hold the disc by its edges and wipe it from the center to the edges with a dry, soft
cloth.Operating Instructions (For Basic Operations)11
1
UsageUsage        
						

							Names and Uses of the Parts
Screen Front ViewNotice•The elite Panaboard is designed exclusively for projector images. Do not write on the screen board
with a white-board marker.12Operating Instructions (For Basic Operations)UsagePosition Sensor
Detects the position of the electronic pen. Do 
not block the sensor while operating the elite
Panaboard.
Screen Board
Project the contents of a computer screen using a 
projector.
Pen Tray
Push the center of the door to open the pen tray, 
which can hold up to 2 electronic pens.
Status LEDs
Left: Power LED (green)
Lights green when the power is on.
Right: Error LED (red)
Blinks red when an error occurs. 
USB Port
Directly connect a computer using a USB cable 
(included).  
						

							Electronic Pen
Notice•Use the electronic pen by holding it at a right angle to the screen board.
Holding it at an angle can cause its position to be read incorrectly.
• Do not use multiple pens at the same time. This can result in erroneous operation.
• Do not push the penpoint while holding the pen close to the elite Panaboard. Doing so can cause
erroneous behavior.
Note
•The electronic pen switches to power-save mode after about 30 minutes.
• When waking up the pen from power-save mode by pushing the penpoint, the pen’s reaction may be
slow.
• When operating the electronic pen, you will hear a buzzing sound due to the pen emitting ultrasonic
waves for location detection. This sound does not have any negative effects for nearby people or
devices. It will not cause electrical shocks.
Operating Instructions (For Basic Operations)13
1
UsagePenpoint
When you push down on the penpoint, ultrasonic waves 
and infrared signals are transmitted, and equivalent of a 
left mouse click is performed.
Ultrasonic Emitter
Do not block this area with your fingers.
Doing so will prevent the elite Panaboard from correctly 
detecting the electronic pens position.
Infrared Emitter
Do not block this area with your fingers.
Doing so will prevent the elite Panaboard from correctly 
detecting the electronic pens position.
Pen Button
Performs the same function as a right-click with a mouse.
Battery Cover   
						

							Inserting (Replacing) Batteries1. Remove (replace) the battery cover.
•When replacing the cover, follow the procedure in
reverse.
2. Insert (exchange) the battery and replace the
cover.
• Make sure to use a AAA alkaline battery, and
ensure that 
 and  face the correct
directions.
14Operating Instructions (For Basic Operations)Usage     
						

							Connecting External Components1.Connect the elite Panaboard to a computer using the USB cable (included).
• Be sure the elite Panaboard software is installed on the computer before connecting it to the elite
Panaboard.
• elite Panaboard: Plug the B connector (smaller connector) into the elite Panaboard's USB port.
Computer: Plug the A connector (larger connector) into a USB port on the computer.
• Do not connect the elite Panaboard via a USB hub. This could result in erroneous operation.
2.Connect the computer to a projector.
• For instructions on connecting your computer and projector, refer to the respecting instruction manuals.
About the Usage Location •Do not place the elite Panaboard where it is directly exposed to sunlight, near a stove, near to a heating/
cooling vent or exposed to strong winds.
• Do not use the elite Panaboard in a location less than 10 °C (50 °F) or in a location subject to extreme
changes in temperature.
Note
•The elite Panaboard may not work properly when used in one of the above locations.
Operating Instructions (For Basic Operations)15
1
UsageUSB Cable
(Included)
Video CableProjector
Computer To USB Port
AC
AC  
						

							Moving the elite Panaboard When Using the Stand (Sold Separately)1.Disconnect the USB cable from the elite Panaboard.
2. Release the locks on the casters.
3. Move the elite Panaboard, avoid banging or shaking the board.
Notice
•Always move the elite Panaboard with 2 people.
• Do not drag or step on the cable.
4. Lock the casters.
16Operating Instructions (For Basic Operations)Usage 
						

							Installing the elite
Panaboard software
You need to install the elite Panaboard software on the
computer that will be used with the elite Panaboard.
To install the elite Panaboard software, follow the
procedure below.
Notice
•Do not connect the USB cable until the
installation is completed.
• Do not connect more than 1 elite Panaboard to
the same computer.
(Doing so can cause erroneous behavior on the
computer.)
1. Turn on your computer and start the Windows
operating system.
• Log into an account with Administrator
privileges.
2. Insert the included CD-ROM into the CD-ROM
drive.
• The setup screen will be displayed.
• If the setup screen does not appear, select your
CD-ROM drive in Explorer and double-click
[Menu.exe].
• In Windows  Vista or Windows  7, if the Autoplay
dialog box is displayed, click [Run Menu.exe].
3. When the "Welcome" screen has been
displayed, click [Next].
4. When the "Model Selections" screen is
displayed, click the type of device you are
using.
5. Click [Install elite Panaboard].
6.If you agree to the terms in the "License
Agreement", click [Yes].
• In Windows Vista, if the "User Account
Control"  window is displayed, click [Continue] to
continue with the installation.
• In Windows 7, if the "User Account Control"
window is displayed, click [Yes] to continue with
the installation.
7. When the following screen is displayed, confirm
that the USB cable is not connected to your
computer or the elite Panaboard, and click  [OK].
• If the USB cable is connected to the elite
Panaboard, disconnect the cable, and click
[OK].
• If .NET Framework 2.0 or later is not installed,
an installation screen will be displayed. Follow
the on-screen directions to install these
components.
8. When the installation wizard is displayed, follow
the on-screen instructions and continue with
the installation.
9. When installation has finished, click [Finish].
• Restart your computer if you are prompted to do
so.
• The group [elite Panaboard] will be created in
the [Panasonic] group in the program menu.
• The following items will appear in the [elite
Panaboard] group:
– elite Panaboard software
– elite Panaboard book
– Operating Instructions for Basic Operations
– Operating Instructions for Software
– Download the latest version
Operating Instructions (For Basic Operations)17
1
Usage   
						

							Setting the Projector
Set up your projector as instructed below.
About Positioning the Image
• When you are projecting an image, make sure that
the edge of the projected image is at least 5 mm
( 1
/4  in.) from the screen frame. The electronic pen
may not function correctly within 50 mm (2 in.) of the
position sensor in the upper-left corner of the screen
board.Project the Image as a Rectangle• Adjust the location of the projector to project at a
right angle with the elite Panaboard.18Operating Instructions (For Basic Operations)UsageProjectable Area
5 mm (1/4 in.)
5 mm
(1/4 in.)
50 mm (2 in.)
5 mm (
1/4 in.)   
						

							•If the image is projected trapezoidally, the
position of the electronic pen may not be read
correctly. Adjust the projector so that the
projected image is a rectangle. Refer to your
projector's documentation for information on
adjusting the projected image.
Set the Proper Resolution
• Set your computer's and projector's resolutions to
the most appropriate setting.
If the resolution is not set properly, the image will be
difficult to see. Particularly, if the projector's
resolution is lower than the computer's, thin lines
can appear cut or broken. Refer to your projector's
documentation for information on adjusting the
resolution.
Do Not Look Directly into the Projector Lamp
• When using a projector, try to avoid looking directly
into the projector lamp. Doing so can hurt your eyes.
Setting Your System
(Calibration)
About Calibration
Calibration is setting up the elite Panaboard and
projector so that lines and comments drawn on the
screen board with the electronic pen will be correctly
displayed on the image projected onto the screen
board. Be sure to perform calibration before use.
After you have set up the elite Panaboard, project an
image onto the screen board and use the elite
Panaboard software installed on your computer to
perform calibration.
After Calibration
Do Not Move the elite Panaboard or the
Projector
• The position of projected image and electronic pen
will become misaligned in the following cases,
requiring you to re-calibrate their positions.
– The location of the projector changed.
– The location of the elite Panaboard changed.
– The image area or placement was changed due
to changes in the zoom, focus, etc.
– The resolution of the projector or the computer
changed.
• If you are using the elite Panaboard installed on a
stand, be aware that accidentally hitting the elite
Panaboard or pushing too strongly with the
electronic pen while operating can move the stand's
position, which will result in misalignment of the
projected image and the electronic pen's position.
• Make sure to lock the stand’s casters when using
the elite Panaboard, as failing to do so can cause
misalignment.Operating Instructions (For Basic Operations)19
1
Usage  
						

							Starting the elite
Panaboard software and
Performing Calibration
1. Connect the elite Panaboard to your computer
with the USB cable.
• The elite Panaboard software starts
automatically.
• When you start the elite Panaboard software for
the first time, the calibration screen is displayed.
• Restart your computer if you are prompted to do
so. After the computer has restarted, connect
the elite Panaboard to your computer with the
USB cable.
2. Perform calibration.
3. Press the electronic pen at a right angle against
the board at the intersecting points of each
circle until it disappears (about 2 seconds).
Repeat in the order shown in the illustration
below.
• Hold and press the electronic pen at a right
angle to the screen board.
• When you push down on the penpoint, the
electronic pen makes a buzzing sound.
• When the position of the indicated point has
been determined correctly, calibration
automatically moves to the next point.
• When calibration has finished normally, a
completion dialog box is displayed.
4. Click [OK].
• If the elite Panaboard and projector are fixed so
that they will not move (Wall mounted case),
select the [Always use this calibration
information.] check box, and click [OK] to skip
calibration from the next time you start the elite
Panaboard software.
20Operating Instructions (For Basic Operations)UsageAB
C D
E