Panasonic Electronic Board Ub-8325 Operating Instructions

Specifications
81
Help
Specifications
Model No.UB-8325
GeneralPower supply Refer to the name plate on the printer
Power consumption
(Operational)Refer to the name plate on the printer
External dimensions 
(Height × Width × Depth, 
without stand)1,388 mm × 1,550 mm × 264 mm 
(4 6 
21/32 × 5 1 1/32 × 10  13/32 )
Mass (without stand) 34.0 kg (75 lbs.)
Ambient operating conditions Interactive Function
Temperature: 15–30°C (59–86
°F)
Humidity: 30–80% RH
Other than Interactive Function
Temperature: 10–35°C...

Specifications
82
*1Letter size is for U.S.A. and Canada models.
•The markers (big) and the eraser are used for other than the interactive function.
•The markers for interactive (small) are used while inserted in the pen holder.
The Electronic Pen [a marker for interactive (small) inserted in the pen holder] and the Electronic Eraser are used 
with the interactive function.
Interactive 
FunctionEffective Area
(Height x Width)Projector mode: 850 x 1,330 mm (2 915/32 × 4 43/8 )
* The position cannot be...

83
Before installing this set, please read this manual completely.
CLASS 1 LED PRODUCT
Installation
Installation Manual
(for qualified service personnel)
Table of Contents
page
For Your Safety  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
●Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  84
Assembling the Electronic Board . . . . . . . . . . . . . . . . . . . . . . . 85
●Accessories for assembling . . . . . . . . . . . ....

84
For Your Safety
To prevent severe injury and loss of life, read this 
section carefully before using the unit to ensure proper 
and safe operation of your unit.
The following graphic symbols are used in this 
Installation Manual.
Safety check must be done by qualified 
service personnel after installing this option.
Be sure to disconnect the power cord while 
installing the unit. Otherwise, it may cause 
electric shock or injury.
Be sure to use the specified parts for the 
installation. Otherwise, it...

85
Installation
Assembling the Electronic Board
■Accessories for assembling
The package includes the parts for setting up the electronic board shown below. Make sure that all of these parts 
are included in the package before proceeding.
No.Part NameIllustrationQ’tyRemarks
Power cord1
Wall-mounting 
template1 For wall-mounting 

Assembling the Electronic Board
86
■Assembly
1Assemble the optional stand or wall-mounting kit.
■If you are using a stand, refer to page 92.
■If you are using a wall-mounting kit, refer to page 96.
2Remove the electronic board from the shipping box.
Remove the joints, then remove the electronic board from the shipping box.
•Do not touch the screen film surface, as this may damage it.
•The shipping box, cushioning material, and other packing material will be necessary if you ever need to 
repackage the...

Assembling the Electronic Board
87
Installation
3Install the electronic board.
Install the electronic board using the stand (option) 
or wall-mounting kit (option). 
■Using the stand (option)
1) Hang the electronic board on the optional 
stand.
•The electronic board can be mounted 
200 mm (7 
7/8”) higher than hang position A 
by hanging it with the wing bolts B.
2) Secure the stand fixture to the electronic 
board using the two wing-bolts [M5 x 12 mm 
(15/32”)] provided with the stand (option).
■Using...

Assembling the Electronic Board
88
4Connect the power cord.
1) Securely fit the supplied power cord into the 
AC inlet on the printer unit.
2) Fasten the power cord through the center 
cable holder, as well as the left or right cable 
holder depending on the location of the AC 
outlet (see below).
•Left Location
When fastening through the left cable holder, 
fasten the power cord through the cable 
holders as shown below:
•Right Location
When fastening through the right cable holder, 
fasten the power...

89
Installation
Electronic Board Operations Check
After assembling the electronic board, perform the procedures presented in the following table to make sure it 
functions properly.
StepPoints to Check
SymptomSolutions
1Turn on the power switch.“ ” flashes after “ ” lights up. (Normal operation)
(If not) Check power cord. (See step 
4 on page 88.)
2Open the printer door and attach the 
accessory thermal transfer film, then 
close the printer door.
•Installing Thermal Transfer Film 
procedure (refer to...

Electronic Board Operations Check
90
*1Contact the store or dealer from which the unit was purchased.
■Interactive Operations Check
1Install the software on the computer and connect the supplied USB cable according 
to “Installing Drivers / Interactive Panaboard Software” on page 28.
2Check that the interactive function operates.
•If the Electronic Pen position shifts, adjust the position according to the instructions on page 36.
10Press .Two screens are copied 
properly.(Normal operation)
(If not)
*1...