Panasonic EYFR02 Operating Instructions
Have a look at the manual Panasonic EYFR02 Operating Instructions online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 9
- 9 -
• About menu
Allows you to check the software’s version.
Installing the assembly qualifier
Installation method
Mount the assembly qualifier securely with screws using the four mountin\
g holes.
NOTE
Before mounting the assembly qualifier, test it where you plan to install it to ensure
that there are no communications issues.
CAUTION
Verify that the assembly qualifier is not affected by other wireless equipment before
mounting it.](http://img.usermanuals.tech/thumb/58/62068/w64_ey-fr02_en_om_d-8.png "Page 9
- 9 -
• About menu
Allows you to check the software’s version.
Installing the assembly qualifier
Installation method
Mount the assembly qualifier securely with screws using the four mountin\
g holes.
NOTE
Before mounting the assembly qualifier, test it where you plan to install it to ensure
that there are no communications issues.
CAUTION
Verify that the assembly qualifier is not affected by other wireless equipment before
mounting it.")
![Page 10
- 10 -
III. OPERATION
Registering the tool with the assembly qualifier
● Preparing the assembly qualifier
1. Connect the power cord to the assembly qualifier.
. Plug the power cord into a wall outlet.
3. Turn on the assembly qualifier.
All indicators will turn on and off, leaving only the power indicator on.
4. Insert a mode switching key into the key lock and turn to the left.
The power indicator will flash, and the assembly qualifier will enter to\
ol
registration standby mode.
●...](http://img.usermanuals.tech/thumb/58/62068/w64_ey-fr02_en_om_d-9.png "Page 10
- 10 -
III. OPERATION
Registering the tool with the assembly qualifier
● Preparing the assembly qualifier
1. Connect the power cord to the assembly qualifier.
. Plug the power cord into a wall outlet.
3. Turn on the assembly qualifier.
All indicators will turn on and off, leaving only the power indicator on.
4. Insert a mode switching key into the key lock and turn to the left.
The power indicator will flash, and the assembly qualifier will enter to\
ol
registration standby mode.
●...")
- 11 - Setting the beep volume Set the beep volume with the volume switch. Low volume (Approx. 70 dB) OFFHigh volume (Approx. 85 dB) NOTE The beep mode setting is configured while the assembly qualifier is connected to a computer. See page 7. Using the software 1. Turn on the assembly qualifier’s power switch. All indicators will turn on and off, leaving only the power indicator on. 2. Use the registered tool to perform fastening work. Status of tool’s fastening confirmation indicator Assembly qualifier indicators GreenFastening PASS indicator RedFastening FAIL indicator Finishing work Turn off the assembly qualifier’s power switch. I/O connector Pin no.Description 1Reset input pin (input) Reset input pin (common) 3Relay output pin (common) 4Relay output pin (fastening PASS) 5Relay output pin (fastening FAIL)
- 1 - 5-pin connector schematic and pin out To connect to the 5-pin connector, you will need: A commercially available round connector (manufacturer: Amphenol ; model no.: T3360 001) System wiring 1. Unplug the assembly qualifier and turn off the power switch. 2. Connect the assembly qualifier to an external device (sequencer, etc.). Example connection Assembly qualifier External device Input Rated: 4V/60mA Rated input: 4V/60mA Input Rated: AC50V/5ARated output: DC30V/5A Input Rated: AC50V/5ARated output: DC30V/5A PLC, etc. Input signal for analyzing output Relay Relay PLC, etc. CAUTION Exercise caution not to exceed the rated load as doing so may damage internal circuitry.
- 13 - IV. SPECIFICATIONS ModelEYFR0 Rated supply voltage100/40, 50/60 Hz Rated supply current 0.1 A Frequency.410 GHz to .465 GHz Recommended communications range10 m* No. of connected devices1 External connection output5A at AC50V or 5A at DC30V Operating temperature range–10ºC (14ºF) to 60ºC (140ºF) Compatible toolsEYFLA4AR, EYFLA5AR, EYFLA5QR, EYFLA6JR, EYFLA6PR, EYFMA1JR, EYFMA1PR Dimensions 10 mm × 60 mm × 70 mm Weight1.1 kg * Communications range varies with operating environment. The presence of metal walls, people, or other objects may result in decreased range. Radio Information: Indoor/Urban Range 100 ft./30 m Transmit Power 1 mW (0 dBm) Receiver Sensitivity -9 dBm (1% B0 packet error) FCC Part 15.47 OUR-XBEE Industry Canada 414A XBEE FCC Statement: Contains FCC ID: OUR-XBEEThe enclosed device complies with Part 15 of the FCC Rules. Operation is\ subject to the following two conditions: (i.) this device may not cause harmfu\ l interference and (ii.) this device must accept any interference received, including\ interference that may cause undesired operation. Channel Frequencies: Channel 1 .410 GHz Channel .415 GHz Channel 3 .40 GHz Channel 4 .45 GHz Channel 5 .430 GHz Channel 6 .435 GHz Channel 7 .440 GHz Channel 8 .445 GHz Channel 9 .450 GHz Channel 10 .455 GHz Channel 11 .460 GHz Channel 1 .465 GHz
PANASONIC CONSUMER ELECTRONICS COMPANYOne Panasonic Way, Secaucus, New Jersey 07094 EN EY9811FRZ01 H110 Printed in Japan