Panasonic High Speed Color Scanner Kv S3065 Operating Instructions

							Replacing Consumables
31
11Hold the conveyor using both hands,
and close the conveyor by pushing it
into the unit.
≥When the conveyor is closed, the click-
stop mechanism will operate.
Caution:
If the conveyor is not closed correctly and
the front door is closed, the conveyor may
break.
12Close the front door.
≥Push both sides of the front door down
slowly until it clicks into place.
13Clear the roller replacing counter with
User Utility.
≥Click [Clear Counter] button for [After
Replace Roller] with User Utility.
Indent
Conveyor 
						

							32
Shading Adjustment
¥What is the purpose of the shading adjustment?
The process whereby the variations in the distribution of the lamp’s light quantity are transformed into a fixed output
within the scanning range is known as shading adjustment. It can be carried out by means of the User Utility using
the special shading paper which is provided with this scanner.
¥When shading adjustment is required
Proceed with the compensation when the colors in some parts of the scanned images differ in the extreme, or when
the image quality fails to be improved even after the inside the scanner is cleaned.
¥Before proceeding with the shading adjustment
Before proceeding, be absolutely sure to thoroughly clean the image sensor cover (F). Image sensor cover (B) as
well as the transport path and drive rollers of the scanning unit.
If the shading adjustment is carried out while these par ts are still dirty, it will not be possible to eliminate the lines that
form on the scanned images.
¥Shading adjustment procedure
1. Start the User Utility.
2. Click “User Shading” on the main menu, and operate as the image display dictates. For further details, refer to 
section 4.6 in the User Utility Reference Manual.
¥Caution
If the scanned images are still lined after the shading adjustment has been performed and if these lines are not elim-
inated even after the image sensor cover areas have been cleaned, it means that the shading has not been compen-
sated properly. Clean the parts again, and then proceed with the shading adjustment. 
						

							33
Repacking Instructions
It is highly recommended that you keep the original carton and ALL packing materials. If you need to transport or
ship your scanner, please follow these instructions.
≥Please use the original carton and all of the original packing materials.
≥Improper repacking of the scanner may result in a service charge to repair the unit.
≥The scanner should be handled in the correct (horizontal) position.
Materials Required :
≥Original Scanner Carton & Packing Materials
≥Shipping Tape and Scissors
1Disconnect your scanner from the electrical outlet and the interface cable.
2Fold the plastic part of the exit stopper and put the exit stopper into the exit extension
tray. Slide the exit extension tray into the pre-imprinter door if it is pulled out.
3Open the pre-imprinter door and tighten the screw.
4Pack the scanner.
Pre-imprinter door
Screw
≥CD-ROM 1 piece
Operating Instructions
Driver Software
Power Cord
≥Installation manual
≥Maintenance manual
≥Roller cleaning paper 
(3 pieces)
≥Shading chart
Joint ≥Blower
USB cable 
						

							34
Specifications
Item
Model No.KV-S3065CLKV-S3065CW
ScannerScanning face Duplex scanning
Scanning methodFront side : CIS (Contact Type Color Image Sensor)
Back side : CIS (Contact Type Color Image Sensor)
Scanning width 227 mm (8.9 in.) 302 mm (11.9 in.)
Readout speedSimplex scanning :
Approx. 65 sheets/min. (Letter, fed lengthwise, 200 dpi)
Approx. 60 sheets/min. (A4, fed lengthwise, 200 dpi)
Duplex scanning :
Approx. 60 sheets/min. (Letter, fed lengthwise, 200 dpi)
Approx. 55 sheets/min. (A4, fed lengthwise, 200 dpi)
ResolutionMain scanning direction : 100~600 dpi (1 dpi step)
Sub-scanning direction : 100~600 dpi (1 dpi step)
(Same as main scanning direction)
The optical resolution is 600 dpi.
Tonal gradationBinary mode, Grayscale mode (8 bit), 64-step gradation 
(dither) mode, Error diffusion mode
Image controlImage emphasis, Dynamic threshold, Automatic separation, 
Invert, White level from paper
Compression MH (G3), MR, MMR (G4), JPEG
PaperSize* 48k70 mm (1.9k2.75 in.) to 297k431 mm (11.7k17 in.)
ThicknessSingle paper feeding : 0.025 to 0.2 mm (1.0 to 7.9 mils)
Continuous paper feeding : 0.06 to 0.2 mm (2.4 to 7.9 mils)
Note: 1 mil = 1/1000 in.
WeightSingle paper feeding : 20 to 157 g/m
2 (5.3 to 42 lbs.)
Continuous paper feeding : 40 to 157 g/m2 (11 to 42 lbs.)**
Smaller than A7 size : 157 g/m2 only
Hopper capacitySmaller than Letter/A4 portrait : 300 sheets (64 g/m
2) 17 lbs.
Wider than Letter/A4 portrait  : 200 sheets (64 g/m2) 17 lbs.
UnitExternal dimensions 
(WidthkDepthkHeight)495k575k288 mm (19.5k22.7k11.4 in.)
Mass (Weight) 24 kg (53 lbs.)
Power requirementAC100 – 120 V, 50/60 Hz
AC220 – 240 V, 50/60 Hz
Power
consumptionMaximum
(Scanning)1.4 A (AC100 – 120 V)
0.6 A (AC220 – 240 V)
Minimum
(Standby)0.6 A (AC100 – 120 V)
0.3 A (AC220 – 240 V)
Sleep mode8 W (AC100 – 120 V)
8 W (AC220 – 240 V)
“Weight in pounds” of paper represents the weight of 500 [17k22 inches (432k559 mm)] sheets.
* The scanning size depends on the memory installed in the scanner. Refer to PIE Reference Manual for details.
** For scanning thin paper (with paper weight less than 50 g/m
2), the optional roller exchange kit for thin paper is
recommended. 
						

							Specifications
35
Operating
EnvironmentOperating temperature and 
humidity15 °C to 30 °C (59 °F to 86 °F), 20% to 80% RH
Storage
EnvironmentStorage temperature and 
humidity0 °C to 35 °C (32 °F to 95 °F), 10% to 80% RH
OptionRoller exchange kit (KV-SS017)
Roller exchange kit for thin paper (KV-SS018)
Imprinter option (KV-SS014)
Roller cleaning paper (KV-SS03)
Ink cartridge (KV-SS021)
Item
Model No.KV-S3065CLKV-S3065CW 
						

							36
Troubleshooting
If a problem occurs while the unit is being used, check the following items and check the scanner status with the User
Utility. If the unit still malfunctions, turn it OFF, unplug the power cord and call for service.
SymptomPossible CauseRemedy
The front door cannot be
opened.The screw is not loosened.Open the pre-imprinter door and
loosen the screw. (Refer to the
Installation Manual on page 19.)
The LED does not light when
the power switch is turned
ON.The power cord is not plugged in. Insert the power plug firmly.
Problem with power supply.Disconnect the scanner from the
electric outlet and call for service.
The computer does not
recognize the scanner.The scanner is not connected to the
computer correctly.Connect the cables correctly.
The scanner is not registered 
correctly.Uninstall the scanner from the
computer. 
Register the scanner hardware again.
(Refer to the Installation Manual on
pages 25 and 26.)
SCSI 
connectionThe computer cannot recognize the
SCSI card.Check your computer whether the
SCSI card is installed correctly using
the device manager’s property. Refer
to the Installation Manual on page 24.
The same ID number is used for the
scanner and the other device.Use the different SCSI ID numbers for
each devices. (See page 12.)
The scanner was turned on after the
computer was turned on.Turn the computer OFF. Turn the
scanner ON, and then turn the
computer ON again.
USB  
connectionThe USB interface of the computer is
not installed correctly.Check the computer whether the USB
interface of your computer is installed
correctly using the device manager’s
property.
The scanner is connected via USB
hub.Do not connect via USB hub.
The cable without High-Seed logo is
used.Use the cable with High-Speed logo.
Scan speed is slow at USB
connection.The scanner is connected with USB
1.1.Connect with USB 2.0.
The document has been
loaded on the hopper tray.
But the scanner does not
start scanning.The document is not loaded 
properly.Load the document correctly.
(See pages 13–16.)
The sensor cannot detect the
document as the edge of the document
is curled.Flatten the document and load it again. 
						

							Troubleshooting
37
Double feeding problems
occurs frequently or the
scanner stops loading while
scanning.The rollers are dirty. Clean all of the rollers. (See page 23.)
The rollers have reached their life
expectancy.Replace the paper feed roller module
and the retard roller module. (See
page 27 and page 29.)
The document is curled or folded.Flatten the document and load it again
after reducing the pages.
The irregular type document is to be
scanned.Make a copy of the document on
specified paper (see page 13) and
scan the copy.
The document has a length of less
than 70 mm (2.75 in.).Make a copy of the document on paper
of the specified size and scan the copy.
(See page 13.)
A paper jam occurs
frequently.The ADF/manual feed selector is not
set in the correct position.Set the ADF/manual feed selector
correctly. (See page 17.)
Scanned image is aslant.The document guides are not adjusted
to the size of the document to be
scanned.
The document to be scanned is set
aslant on the hopper tray.Adjust the document guides properly to
the size of the document to be
scanned.
Right and left sides of the document to
be scanned are not the same in height,
because of curl and fold.Remove curl and fold then reduce the
amount of the document.
The scanned document is
blank.The document to be scanned was
loaded face down (upside down).Load the document correctly. 
(See page 15.)
Vertical lines appear on the
scanned document.The image sensor covers are dirty.Clean the image sensor covers (F and
B). (See page 26.)
The scanning density is
uneven.The image sensor covers are dirty.Clean the image sensor covers (F and
B). (See page 26.)
The quantity distribution of light varies.Adjust shading. Please refer to section
4.6 of a user utility reference manual.
The color of the scanned
document is extremely
different from the original
document.The settings of the computer monitor is
wrong.Adjust the computer monitor settings.
Dark spots or noise appear
on the scanned documents.The image sensor covers are dirty.Clean the image sensor covers. (See
page 26.)
Scanned image has moire
fringes such as stripe or
wavy pattern noise.It is caused by printing pattern of the
document and the congeniality of the
scanning resolution.Please use the moire reduction
function or change the resolution and
try to scan.
SymptomPossible CauseRemedy 
						

							38
Pag e Pa ge
Index
A
AC inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Acceptable documents . . . . . . . . . . . . . . .  13
ADF / manual feed selector  . . . . . . . .   10, 17
B
Belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  24
Blower . . . . . . . . . . . . . . . . . . . . . . . . . . . .  26
C
CD-ROM . . . . . . . . . . . . . . . . . . . . . . . . . 1,  9
Cleaning the unit . . . . . . . . . . . . . . . . . . . .  22
Component identification  . . . . . . . . . . . . .  10
Control sheet  . . . . . . . . . . . . . . . . . . . . . .  18
Conveyor  . . . . . . . . . . . . . . . . . . . . . .   29, 31
Conveyor rollers . . . . . . . . . . . . . . . . . . . .  24
CPU  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2
D
DIP switch . . . . . . . . . . . . . . . . . . . . . . . . . 12
Document guide . . . . . . . . . . . . . .  10, 13 , 14
Documents to avoid  . . . . . . . . . . . . . . . . .  13
Double feed detector  . . . . . . . . . . . . . . . .  26
Drive rollers. . . . . . . . . . . . . . . . . . . . . . . .  24
E
Energy Star . . . . . . . . . . . . . . . . . . . . . . . . .  2
Exit document guide . . . . . . . . . . . . . . . . .  10
Exit extension tray  . . . . . . . . . . . .  10, 16 , 33
Exit path  . . . . . . . . . . . . . . . . . . . . . . . . . .  21
Exit stopper . . . . . . . . . . . . . . . . . . . . .  10, 16
Exit substopper . . . . . . . . . . . . . . . . . .   10, 16
Exit tray . . . . . . . . . . . . . . . . . . . . . . . .  10, 13
F
Fan exhaust vent . . . . . . . . . . . . . . . .   10, 22
Free rollers . . . . . . . . . . . . . . . . . . . . . . . .   24
Front door  . . . . . . . . .   10, 19 , 21 , 23 , 25 , 27
Front door release . . .   10, 19 , 21 , 23 , 25 , 27
G
Green levers  . . . . . . . . . . . . . . . . . . .   27, 28
H
Hopper . . . . . . . . . . . . . . . . . . . . . . . . . . .   10
Hopper extension tray  . . . . . . . . . . . .   10, 16
Hopper tray  . . . . . . . . . . . . . . . . . . . . . . .   13
I
Image sensor cover . . . . . . . .  22, 24 , 26 , 32
Imprinter option  . . . . . . . . . . . . . . . . . . . .   35
Indent . . . . . . . . . . . . . . . . . . . . . . . . .   29, 31
Ink cartridge . . . . . . . . . . . . . . . . . . . . . . .   35
Interface . . . . . . . . . . . . . . . . . . . . . . . . . . .   2
L
Landscape . . . . . . . . . . . . . . . . . . . . . . . .  15
LED  . . . . . . . . . . . . . . . . . . . . . . . . . .   11, 36
Limit mark  . . . . . . . . . . . . . . . . . . . . .   13, 15
Loading documents . . . . . . . . . . . . . . . . .   13
M
Memory  . . . . . . . . . . . . . . . . . . . . . . . . . . .   2
Multiple sheets . . . . . . . . . . . . . . . . . . . . .   14
N
Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   4 
						

							Index39
Pag e Pa ge
O
Operating environment . . . . . . . . . . . . . . .  35
Option . . . . . . . . . . . . . . . . . . . . . . . . . . . .  35
OS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2
P
Paper feed roller . . . . . . . . . . . . . . . . . . . . 24
Paper feed roller block shaft . . . . . . . . . . .  27
Paper jam sensor . . . . . . . . . . . . . . . . . . .  26
Paper jams . . . . . . . . . . . . . . . . . . . . . . . .  21
Paper path selector. . . . . . . . . . . .  10, 17 , 24
Paper sensor  . . . . . . . . . . . . . . . . . . . . . .  26
Pointer  . . . . . . . . . . . . . . . . . . . . . . . . . . .  24
Portrait  . . . . . . . . . . . . . . . . . . . . . . . . . . .  15
Post-imprinter door . . . . . . . . . . . . . . . . . .  10
Power cord . . . . . . . . . . . . . . . . . . . . . .  4, 10
Power indicator . . . . . . . . . . . . . . . . . . . . .  10
Power switch. . . . . . . . . . . . . .  10, 11 , 22 , 27
Precautions . . . . . . . . . . . . . . . . . . . . . . . . .  7
Pre-imprinter door . . . . . . . . . . . . . . . . . . .  10
R
Reference plate  . . . . . . . . . . . . . . . . . . . . 19
Reference plate lever . . . . . . . . . . . . . . . .  19
Reflector . . . . . . . . . . . . . . . . . . . . . . . . . .  26
Repacking . . . . . . . . . . . . . . . . . . . . . . . . .  33
Replacing consumables . . . . . . . . . . . . . .  27
Retard roller  . . . . . . . . . . . . . . . . . . . . . . .  24
Retard roller module . . . . . . . . . . . . . .   29, 30
Roller cleaning paper  . . . . . . . . . . .  4, 22 , 35
Roller exchange kit . . . . . . . . . . . . . . . . . .  35
S
SCSI connection  . . . . . . . . . . . . . . . . . . . .   2
SCSI connector  . . . . . . . . . . . . . . . . . . . .   10
SCSI ID setting  . . . . . . . . . . . . . . . . . . . .   12
Separation roller. . . . . . . . . . . . . . . . . . . .   24
Separation sheet  . . . . . . . . . . . . . . . . . . .   18
Shading  . . . . . . . . . . . . . . . . . . . . . . .   32, 37
Skew sensor  . . . . . . . . . . . . . . . . . . . . . .   26
Specifications . . . . . . . . . . . . . . . . . . . . . .   34
Starting sensor . . . . . . . . . . . . . . . . . . . . .   26
STOP/START button . . . . . . . . . . . . . . . .   10
System requirements . . . . . . . . . . . . . . . . .   2
T
Troubleshooting . . . . . . . . . . . . . . . . . . . .  36
U
USB connection . . . . . . . . . . . . . . .  2, 11 , 12
USB connector . . . . . . . . . . . . . . . . . . . . .   10
USB hub. . . . . . . . . . . . . . . . . . . . . . . .   2, 36
User utility  . . . . . . . . . . . . . . . . . .   11, 25 , 32
W
Waiting sensor . . . . . . . . . . . . . . . . . . . . .   26 
						

							Panasonic Digital Document Company
A Unit of Matsushita Electric Corporation of America
Two Panasonic Way, Secaucus, New Jersey 07094
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga, Ontario, L4W 2T3
Matsushita Electric Industrial Co., Ltd.
http://www.panasonic.co.jp/global/
© 2004 Panasonic Communications Co., Ltd. All Rights Reserved.
E-04091007