Panasonic Home Network System Window Door Sensor Kx Hns101 Installation Guide

Temporary placement
Before installing the window/door sensor, temporarily place it in the desired
location and confirm that it operates properly by pressing  M
N.
Important:
R Attach the sensor unit to the outer frame of the window or door, and the magnet
unit to the inner frame.
R Attach both units so that the “
” marks point toward each other and are within
25.4 mm (1 inch) of each other.
R The window/door sensor will not operate properly if the “
” marks are too far
apart or are facing the wrong way....

Example 1: Installed on the left of the windowCorrectIncorrect
 “” marks point directly at each
other and are within 25.4 mm (1 inch). “” marks are not aligned. Magnet
unit is too high/too low.
 “” marks are aligned but units
are too far apart.
12For assistance, please visit www.panasonic.com/support
Setup 1  1
{xC}
GREEN  2  2
{xC}
RED 3  3
{xC}
RED  

Example 2: Installed on the right of the windowCorrectIncorrect
 “” marks point directly at each
other and are within 25.4 mm (1 inch). “” marks are not aligned. Magnet
unit is too high/too low.
 “” marks are aligned but units
are too far apart.
For assistance, please visit www.panasonic.com/support13
Setup 1  1
{xC}
GREEN  2  {xC}
RED2 3  3
{xC}
RED  

Installation
Install the window/door sensor in the same position where proper operation was
confirmed (page 11). You can install the window/door sensor using screws or
double-sided tape, depending on your preference or the material of the installation
area.
Note:
R When installing, make sure the battery is inserted properly and the sensor unit
cover is completely closed.
R Use screws when installing on a wooden surface. Do not use double-sided tape.
Securing with screws
1 Remove the covers from each...

2Sensor unit:
Attach the sensor unit.
 Screws 86.2 mm (3 25/64 inches)
Magnet unit:
Attach the magnet unit.
 Screws 24.4 mm (31/32 inches)
3 Attach the covers.
Important:
R
 Align the “” marks on the sensor unit and the magnet unit so that they
point directly at each other and are no more than 25.4 mm (1 inch) apart.
For assistance, please visit www.panasonic.com/support15
Setup1 2 3 4 24 1
13
3
5 5   

Securing with double-sided tape
Note:
R Make sure the surfaces of the sensor unit, magnet unit, and the installation area
are clean and dry before applying double-sided tape.
1 Check that the sensor unit cover and magnet unit cover are attached.
2 Affix double-sided tape to the sensor unit and magnet unit.
R Make sure the tape covers the screw holes on the back of each unit.
3 Install the sensor unit and magnet unit.
R Press firmly on each unit to ensure solid adhesion to the installation surface....

Testing the window/
door sensor
You can check the window/door
sensor’s LED indicator and test the
performance of the window/door
sensor.
1 Remove the sensor unit cover.
2 Press  M
N on the sensor unit.
3 Open and close the window or
door several times.
R Make sure that the LED
indicator lights in green when
you close the window or door.
4 Press  M
N again.
Note:
R If the LED indicator lights in red
when the window or door is closed,
the window/door sensor is not
installed properly. Re-evaluate the...

Specifications
R Frequency range
DECT: 1.92 GHz – 1.93 GHz
R RF transmission power
DECT: 115 mW (max.)
R Power source
Lithium battery CR2 (1  ´ 3.0 V,
850 mAh)
R Operating conditions
-10 °C – 40 °C (14 °F – 104 °F)
R Battery life
Approx. 2 years (when window/door
is opened and closed 10 times a
day, in an environment of 25 °C
(77 °F))
R Dimensions
Sensor unit:  Approx. 102 mm  ´
31 mm  ´ 22 mm (4 inches  ´ 1 7/32
inches  ´ 7/8 inches)
Magnet unit:  Approx. 37 mm  ´
14 mm  ´ 14 mm (1 15/32 inches  ´
9/16...

FCC and other
information
This device complies with Part 15 of
the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful
interference, and (2) this device must
accept any interference received,
including interference that may cause
undesired operation.
Privacy of communications may not be
ensured when using this phone.
CAUTION:
Any changes or modifications not
expressly approved by the party
responsible for compliance could void
the user’s authority to...

Notice:
R FCC ID can be found inside the
sensor unit.20For assistance, please visit www.panasonic.com/support
Appendix