Panasonic Home Theater Audio System Sc Zt2 Operating Instructions

							VQT2R70
21
„ Setup menu items
“REMOTE”              “INPUT MODE”        “RESET”
✽“BASS”✽“TREBLE”✽“BALANCE” 
“SPEAKERS”   
✽“DISTANCE”
  
✽“STB AUDIO”
“7.1CH  VS” 
“HDMI” “SOUND DLY”
“DUAL PRG”   “DRCOMP”  “
ATTENUATOR” 
“EXIT”
•  ✽ appears only when audio adjustment can be made.
• Select “EXIT ” and press [OK] to finish the setup mode.
Adjusting sound quality
You can adjust the level of bass and treble.
This setting is effective only when you perform stereo playback 
of 2-channel analog and PCM signals (during Dolby Virtual 
Speaker and Dolby Pro Logic 
 is off).
This setting is not displayed in other conditions. Be sure to make 
this setting in the above condition.
1.  Press and hold [–SETUP, OFF] for about  2 seconds.
The setting items are displayed. (➜ above)
2. Press [ w][
q ] to select “BASS ” or 
“TREBLE ” and press [OK].
3. Press [ e][
r ] for adjustment, and press 
[OK].
Adjustment range: –6 to +6
Factory setting: 0
4. Press [  RETURN] several times to select 
“EXIT ” and press [OK] to fi  nish the 
setting.
Adjusting the volume balance of 
front speakers
You can adjust the balance of the front speakers.
1.  Press and hold [–SETUP, OFF] for about  2 seconds.
The setting items are displayed. ( ➜ above)
2. Press [
w][
q ] to select “BALANCE ” and 
press [OK].
3. Press [ w][
q ] for adjustment, and press 
[OK].
L : Front left
R : Front right
  Move the bar to left and right on the display to adjust. •  As the bar gets closer to “L ”, the sound moves to left front.
•  As the bar gets closer to “R ”, the sound moves to  right front.
4. Press [ RETURN] several times to select 
“EXIT ” and press [OK] to fi  nish the setting.
Note
•  The bar indication is approximate.
•  When using headphones, you cannot adjust the volume 
balance.
Adjusting the surround speaker 
output using the test signal
You can make this setting when using the surround speakers.
You can adjust the surround speaker volume by outputting the 
test signal.
1.  Press [TEST] to output the test signal.
Speaker display
 L  : Front left, R : Front right,
 RS  : Surround right, LS : Surround left
•  The test signal is output from one speaker at a time for two  seconds in the following order. TEST L  p TEST R 
p TEST RS 
p TEST LS
2.  
Press [VOL  +, –] to adjust the volumes 
of front speakers to the normal listening 
level.
 Adjustment range:  0 (Min) to 50 (Max)
3.  Press [CH] to select surround speakers 
for adjustment.
4.  Press [SPEAKER LEVEL +, –] to adjust  each speaker’s output level.
 Adjustment range:  RS, LS : –10 to +10
•  The test signal comes from the speaker being  adjusted.
•  The test signal is output again in the above order 2  seconds after adjustment.
„  Repeat steps 3 and 4 to adjust the level of each speaker.
5.  Press [TEST] to stop the test signal.
Note
•  You can check the audio output of the front speakers. 
(➜  page 14) (When the surround speakers are not used, only 
“TEST L ” and “TEST R ” are displayed and the test signal is 
output alternately.)
•  To adjust the volume balance of left and right front speakers,  see “Adjusting the volume balance of front speakers” 
(➜  right).
•  Even if you adjust each channel level in this adjustment, each  channel level setting in each SFC mode ( ➜ page 17) does 
not change.
•  When you make this adjustment while using the front  speakers only, Dolby Virtual Speaker functions. When 
playing 2-channel sources, Dolby Pro Logic   also works in 
conjunction. (➜ page 17)
•  To adjust the bass volume, do not output the test signal for  adjustment. (➜ page 20)
Functions and settings
Play
5%
						

							VQT2R70
22
Setting distances
You can make this setting when using the surround speakers.
This setting is not displayed under different conditions.
By setting the distance from front/surround speakers to the listening-viewing position, the 
sound delay time is automatically calculated and adjusted so that sound reaches th\
e listener 
at the same time.
1.  Press and hold [–SETUP, OFF] for about 2 seconds.
The setting items are displayed. (➜ page 21)
2. Press [
w][
q ] to select “DISTANCE ” and press [OK].
3. Press [ w][
q ] to select a speaker to set and press [OK].
FRONT : Front speakers
SURR : Surround speakers
4. Press [
e][
r ] to select the distance and press [OK].
Adjustment range:  1.0 to 10.0 meter (3.0 to 30.0 ft (feet))
Factory setting:  Front         3.0 meter (10.0 ft (feet))
Surround 1.5 meter (5.0 ft (feet))
5. Press [ RETURN] several times to select “EXIT ” and press 
[OK] to fi  nish the setting.
Note
Radio waves from this system reach the maximum range of 15 m (49 feet) within the same 
room.
Setting 7.1-channel virtual surround
When playing back 7.1-channel LPCM signals, you can enjoy wider sound fi  eld effects as if 
another speaker is added. Factory setting is “AUTO  ”.
When you do not want to use 7.1-channel virtual surround effect, select “ OFF ” in this setting.
1.  Press and hold [–SETUP, OFF] for about 2 seconds.
The setting items are displayed. (
➜ page 21)
2. Press [
w][
q ] to select “7.1CH VS ” and press [OK].
3. Press [ e][
r ] to select “OFF ” and press [OK].
AUTO : The setting is switched between ON and OFF depending on the input 
signals.
Only when 7.1-channel LPCM signals are input, 7.1-channel virtual surrou\
nd 
is ON (When other signals are input, this setting is OFF).
OFF : 7.1-channel virtual surround is always OFF.
Factory setting: AUTO
4. Press [  RETURN] several times to select “EXIT ” and press 
[OK] to fi  nish the setting.
Reducing Standby power consumption 
(In Standby condition (HDMI off mode))
Standby through function (
➜ pages 9, 28) does not work in this mode if you have connected 
through the HDMI terminal.
VIERA Link “HDAVI Control” ( ➜ page 18) will not function when this system is off.
1.  Press and hold [–SETUP, OFF] for about 2 seconds.
The setting items are displayed. (
➜ page 21)
2. Press [
w][
q ] to select “HDMI ” and press [OK].
3. Press [ w][
q ] to select “STNBY ” and press [OK].
4. Press [ e][
r ] to select “OFF ” and press [OK].
OFF :  Standby power consumption reduced 
(approx. 0.2 W) 
ON :  “Standby through” is activated when this system is turned off. (N\
ormal power  consumption)
Factory setting: ON
5. Press [  RETURN] several times to select “EXIT ” and press 
[OK] to fi  nish the setting.
Functions and settings
Play
Functions and settings
To return to the previous display/
To cancel during setting operation: 
Press [
 
RETURN].
5%
						

							VQT2R70
23
Switching between dual sounds
You can switch between dual sounds of Dolby Digital signals.
1.  Press and hold [–SETUP, OFF] for about 2 seconds.
The setting items are displayed. ( ➜ page 21)
2. Press [
w][
q ] to select “DUAL PRG ” and 
press [OK].
3. Press [ e][
r ] to select the audio and press 
[OK].
MAIN : Main audio    SAP : Sub channel audio output
M+S : Main + Sub channel audio output
Factory setting: MAIN
4. Press [  RETURN] several times to select 
“EXIT ” and press [OK] to fi  nish the 
setting.
Clear audio at low volume
Dynamic range compression function for Dolby Digital. 
It compresses the dynamic range so that you can still hear 
dialog and leave the sound fi  eld unaffected.
Use this function when you have to turn the volume down, such 
as late at night.
1.  Press and hold [–SETUP, OFF] for about  2 seconds.
The setting items are displayed. ( ➜ page 21)
2. Press [
w][
q ] to select “DRCOMP ” and 
press [OK].
3. Press [ e][
r ] to select the setting and 
press [OK].
OFF : Normal playback
STANDARD : The best suited playback for each audio 
source
MAX : Always compressed at the maximum level    
Factory setting: OFF
4. Press [  RETURN] several times to select 
“EXIT ” and press [OK] to fi  nish the 
setting.
Switching the attenuator
Switch the attenuator “ON ” when big sounds become distorted 
while playing an analog input source.
1.  Press and hold [–SETUP, OFF] for about  2 seconds.
The setting items are displayed. (➜ page 21)
2. Press [ w][
q ] to select “ATTENUATOR ” 
and press [OK].
3. Press [ e][
r ] to select “ON ” and press 
[OK].
ON, OFF
Factory setting: OFF
4. Press [  RETURN] several times to select 
“EXIT ” and press [OK] to fi  nish the 
setting.
VIERA Link “HDAVI Control” 
setting
When you do not wish to use VIERA Link “HDAVI Control” 
( ➜  page 18), you can set the unlinked operation by selecting 
“OFF ”.
The normal setting is “ON ” (Linked operation).
1.  Press and hold [–SETUP, OFF] for about  2 seconds.
The setting items are displayed. ( ➜ page 21)
2. Press [
w][
q ] to select “HDMI ” and press 
[OK].
3. Press [ w][
q ] to select “CTRL ” and press 
[OK].
4. Press [ e][
r ] to select “ON ” or “OFF ” 
and press [OK].
ON : When the operation is linked
OFF : When the operation is not linked
Factory setting: ON
5. Press [  RETURN] several times to select 
“EXIT ” and press [OK] to fi  nish the 
setting.
Note
• When “CTRL OFF ” is set, the ARC function will be disabled.
Be sure to make the optical digital connection or analog 
connection. (➜ page 9)
Adjusting the time lag between 
audio and video by delaying 
audio output
You can reduce audio and video time lag by adjusting sound 
delay.
1.  Press and hold [–SETUP, OFF] for about  2 seconds.
The setting items are displayed. (➜ page 21)
2. Press [ w][
q ] to select “SOUND DLY ” and 
press [OK].
3. Press [ e][
r ] to select the setting and 
press [OK].
AUTO, OFF, 10, 20, 30, 40, 60, 80, 100, 120, 140,160, 
180, 200
Factory setting: AUTO
4. Press [  RETURN] several times to select 
“EXIT ” and press [OK] to fi  nish the 
setting.
Note
•  If delaying audio output is not necessary, select “OFF ”.
• “AUTO  ” is effective only when connecting the Panasonic TV 
(VIERA) supporting HDAVI Control 3 and later versions. (Auto 
Lip Synchronization Function)
•  When you connect the Panasonic TV incompatible with  HDAVI Control 3 and later versions or non-Panasonic TV, if 
“AUTO  ” is set, “40 ” (msec) is set.
Functions and settings
Play
5%
						

							VQT2R70
24
Functions and settings
Switching the input signal detection setting
Most sources can be played with “AUTO ” (factory setting).
However, in the following cases, change the input signal detection setting.
•  When the beginning of the song is cut during playback of CD, set to “PCM ” (PCM FIX).
•  When the signal is not detected during playback of DTS sources, set to “DTS ” (DTS FIX).
•  When noise occurs, return the setting to “AUTO  ”.
1.  Press and hold [–SETUP, OFF] for about 2 seconds.
The setting items are displayed. (
➜ page 21)
2. Press [
w][
q ] to select “INPUT MODE ” and press [OK].
3. Press [ w][
q ] to select the input and press [OK].
Input: TV, DVD, AUX1, AUX2
4. Press [
e][
r ] to select the detection method of input signal 
and press [OK].
AUTO :  Automatic detection
PCM : PCM (from CDs) digital input fi  xed
DTS : DTS digital input fi  xed
Factory setting: AUTO
  „  Repeat steps 3 and 4 to change setting.
5. Press [ RETURN] several times to select “EXIT ” and press 
[OK] to fi  nish the setting.
Reset (factory settings)
The operation settings for the system will be initialized to the settings made at the time of shipment.
1.  Press and hold [–SETUP, OFF] for about 2 seconds.
The setting items are displayed. (
➜ page 21)
2. Press [
w][
q ] to select “RESET ” and press [OK].
3. Press [ e][
r ] to select “YES ” and press [OK].
YES : Choice for resetting    NO : Choice against resetting
•  To cancel, select “NO ”.
Note
• All the settings are reset when you select “YES ” and the Input Selector automatically switches to “BD/DVD ”.
•  If you select “NO ”, you will return to step 2. To exit setup mode, press [ 
RETURN] a few 
times to display “EXIT ”, and then press [OK].
•  The contents of the speaker setting are not reset. However, the contents set at “Changing  the number of speakers to 4” (➜ page 15) are reset.
When using this system’s remote control, other equipment may operate. In this case, switch 
this system’s remote control code to “REMOTE 1 ”. Do the following to set the same code 
number for this main unit and remote control.
Setting the main unit
1.  Press and hold [–SETUP, OFF] for about 2 seconds.
The setting items are displayed. ( ➜ page 21)
2. Press [
w][
q ] to select “REMOTE ” and press [OK].
3. Press [ e][
r ] to select “1 ” and press [OK].
Factory setting: 2
• 
You cannot fi
 nish the setting mode until the setting on the remote control is changed\
. Go to step 4.
•  To set the remote control code to 2, select “2 ” in step 3 and press [OK].
Setting the remote control
4. 
Press and hold [OK], and then press [TV] (more than 2 seconds).
TV: Remote control code 1
BD/DVD: Remote control code 2 (factory setting)
•  Select the same number as the code number you have selected in step 3.
•  To set the remote control code to 2, press and hold [OK] in step 4, and then press 
[BD/DVD] more than 2 seconds.
5. Press [ RETURN] several times to select “EXIT ” and press 
[OK] to fi  nish the setting.
Note
If different codes are set between the main unit and remote control, the error message 
“REMOTE 2 ” or “REMOTE 1 ” is displayed.
Play
Functions and settings
To return to the previous display/
To cancel during setting operation: 
Press [
 
RETURN].
When other equipment (mini component system, AV amp, etc.) manufacture\
d 
by Panasonic operates with the remote control operations of this system
5%
						

							VQT2R70
25
Troubleshooting and other information
Error messages/Using with headphones/Specifi  cations
Error messages
DisplayCheck point/Cause/Countermeasure Pages
CANCEL MUTE FUNCTION (Scrolling)•  The test signal is not output while muting is on. Cancel muting for operation. 20
MUTE (Blinking) •  This is always displayed while muting is on. 20
NOT POSSIBLE FOR
THIS INPUT SOURCE (Scrolling) •  You cannot use Dolby Virtual Speaker, SFC and Dolby Pro Logic   for dual 
sounds. —
NOT POSSIBLE FOR
THIS PCM SOURCE (Scrolling) •  You cannot use Dolby Virtual Speaker, SFC and Dolby Pro Logic   effect with 
PCM signals with sampling frequency of over 48 kHz. 17
NOT POSSIBLE WHEN USING 
HEADPHONES (Scrolling) •  You cannot use the sound field effects when using headphones.
25
REMOTE 2
REMOTE 1 • 
Set the same remote control code for this main unit and remote control. When “REMOTE 2 ” 
is displayed, set the code to “2 ” on the remote control in step 4 of procedure “When other 
equipment (mini component system, AV amp, etc.) manufactured by Panasonic operates 
with the remote control operations of this system”. When “REMOTE 1 ” is displayed, set the 
code to “1 ” on the remote control in step 4 in the same way.24
SWITCH OFF POWER 
(Scrolling) • 
While “F70 …………” is displayed, all operations but turning ON/OFF operation are not 
available. Turn off the system, unplug the AC power supply cord, and consult your dealer.—
TURN OFF DTS FIX MODE 
(Scrolling) •  When each input is fixed to DTS (DTS FIX), the sound field effects cannot be 
canceled even if you press [–SETUP, OFF]. Cancel DTS FIX. 24
U701 • 
The equipment connected by the HDMI cable is not compatible with this system’s copyright protection technology.—
U703 •  A problem has occurred with the HDMI connection. Try the following to correct 
the problem. Consult your dealer if the error code remains on the display.
  – Turn the connected equipment off and on again.
  – Disconnect the HDMI cable then reconnect it.
  – Do not connect more than 2 sets of equipment to this system’s output. —
U704 •  The system received incompatible video signals through HDMI connection. 
Check the settings of the connected equipment. —
Specifi
 cations
Using with headphones
Note
•  Avoid listening for prolonged periods of time to prevent hearing 
damage.
•  Multi-channel signals are forcibly converged to 2-channel and  output. (2CH MIX)
  However, for DVD audio, the front left and right signals are output.
Turn down the volume closest to the minimum value.
•  Plug type: ø 3.5 mm (1/8 in.) stereo mini plug
g PRE AMPLIFIER SECTION
Input sensitivity / Input impedance
TV, AUX3  600 mV / 47 kΩ
S/N ratio (IHF A) BD/DVD, TV, AUX1, 
AUX2 (Digital Input)  80 dB (IHF 66)
Tone controls BASS  50 Hz, + 6 to –6 dB
TREBLE  20 kHz, + 6 to – 6 dB
Input/Output terminal
Audio Input Analog Input  ( TV, AUX3 )  2
Optical Digital Input  ( TV, AUX2 )  2
Audio Output Audio Output  ( Front L/R, Surround L/R )  4
Subwoofer Output  1
Headphone Output      ( 16 to 64 Ω )  1
Video/Audio
HDMI Input  ( BD/DVD, AUX1 )  2
HDMI Output  ( TO TV (ARC))  1
This system supports “HDAVI Control 4” function. g MAIN UNIT GENERAL
Power supply 
AC 120 V, 60 Hz
Power consumption  16 W
In standby condition   0.5 W
In standby condition  ( HDMI off mode )   0.2 W
Dimensions ( W x H x D )  430 mm x 59 mm x 262 mm
  (16-15/16 x 2-5/16 x 10-5/16)
Mass [ Weight ]  Approx. 2 kg (4.4 lb.)Operating temperature range  0°C to 40 °C (32°F to 104 °F)
Operating humidity range  20 % to 80 % RH (no condensation)
g WIRELESS SECTIONFrequency of the using band  2.4000 GHz to 2.4835 GHzNumber of using channels  3
The reaching distance  15 m (49 ft)∗1
∗1  It is under the condition as follows.
At same room indoor, there is not an obstacle 
between the main unit and the speaker.
And installing a main unit in the position with 
equal to or more than 50 cm height.
SPEAKER
g POWER AMPLIFIER SECTION
∗2
RMS output power 10 % total harmonic distortionWoofer Speaker ch  60 W (100 Hz, 3 Ω)
Mid High Speaker ch  20 W (1 kHz, 8 Ω)
System Total Power
∗3  160 W (80 W x 2) FTC output power
1.0 % total harmonic distortion
50 Hz to 250 Hz  Woofer Speaker ch 37 W (3 Ω)
250 Hz to 20 kHz  Mid High Speaker ch 13 W (8 Ω)
System Total Power∗3  100 W (50 W x 2)
g SPEAKER SECTION∗2
2-way 5 speakers system (Bass reflex type) Woofer part  12 cm cone type x 1
Mid High part  2.4 x 10 cm flat type x 4
g SPEAKER GENERAL
∗2
Power supply  AC 120 V, 60 Hz
Power consumption  20 W
Wireless Link Standby  0.8 W
In Standby condition  0.1 W
Dimensions ( W x H x D ) 290 mm x 1231 mm x 290 mm
  (11-13/32 x 48-15/32 x 11-13/32)
Mass [ Weight ] Approx. 3.9 kg (8.6 lb.)Operating temperature range  0°C to 40°C (32°F to 104°F)Operating humidity range 20 % to 80 % RH (no condensation)∗2:  per 1 speaker
∗3:  use 2 speakers
Note: 1.  Specifications are subject to change 
without notice.
 2.   Total harmonic distortion is measured by 
the digital spectrum analyzer.
 3.   Total harmonic distortion is measured by 
using AES17 filter.
MAIN UNIT
W
 (Headphone) jack
Headphones
(not included)
5%
						

							VQT2R70
26
Troubleshooting guide
Troubleshooting and other information
Before requesting service, make the following checks.
If you are in doubt about some of the check points, or if the remedies indicated in the chart do not solve the problem, refer to “Customer Services Directory 
(United States and Puerto Rico)” on page 30 if you reside in the U.S.A. or Puerto Rico, or refer to “Product information” on page 29 if you reside in Canada.
Troubleshooting guide
Problem Possible solutionPages
Common problems
No power.•  Ensure the AC power supply cord is connected. 12
“2CH SEARCH ” or “4CH SEARCH” 
does not go off on the display 
while setting the speakers.•  Make sure that the speakers are on.
DIf the display does not go off even when the speakers are on, consult your 
dealer. 13,15
No sound or image after 
playback starts. •  Select the correct source.
•  Turn the muting off.
•  Check that the digital signals can be decoded by this system.
With the optical fiber connection, cannot play back PCM signal with sampling 
frequency of over 96 kHz.
•  Check connections to other equipment.
•  (When the audio is not heard from TV) The optical fiber cable or stereo  connection cable is necessary to connect with a TV incompatible with ARC. 
For details, refer to the operating instructions for the connected TV.
• Set “AUTO  ” in “Switching the input signal detection setting”.
•  Turn this system off then on again.
•  Make sure that the speakers are on.
•  Make sure that the speakers have been properly set.
•  Adjust the speakers.
•  If the connections are normal, this may be a cable-related problem. Use other  cables and make connections again. 16
20
27
9 to 12 9
24 —
13,15 14
20,21 —
The remote control does 
not work. •  Replace the batteries if they are worn.
•  Make sure the remote control code has been properly set. 7
24
No sound from microphone 
connected to DVD player (karaoke)
. • 
No sound is output from microphone if this system is digitally connected\
 with DVD 
player. Change to analog connection and input. Make analog connection to AUX3.11,12
There is no DTS audio output. 
There is audio output, but the 
DTS decoder indicator is not lit.•  Set the DTS Digital Audio Output setting on the DVD player, Blu-ray Disc 
player or DVD recorder to Bitstream.
• Set “DTS ” in “Switching the input signal detection setting”. —
24
Sound is not heard when 
playing DVD audio. • 
This may occur due to digital copyright protection of the disc if using optical digital connection. 
This system may not be able to play sources with sampling frequency of over 48 kHz.—
“F70  †††† ” appears on 
the display.
(“DSP ” or “HDMI ” is 
displayed in  †.) •  Turn off the system, unplug the AC power supply cord, and consult your 
dealer. —
“F76 ” appears on the display.
(After displayed, the system turns off.)•  Unplug the AC power supply cord, and consult your dealer.
—
This system switches to 
standby mode. •  This system is automatically turned off when no signal is input and no 
operation is performed for approx. 30 minutes. —
Sound fi
 eld
No sound in surround 
mode •  Set to Dolby Virtual Speaker, Dolby Pro Logic  or SFC.
17
Cannot use Dolby Virtual 
Speaker, Dolby Pro Logic   
or SFC. •  You cannot use these features with PCM signals with sampling frequency of 
over 48 kHz. Make analog connection to AUX3.
•  You cannot use for Dolby Digital dual sounds. 11,12
—
HDMI
When using an HDMI 
connection, the fi  rst few 
seconds of sound is cut off. •  This may occur if you start play from a chapter on a DVD. The following will 
correct the problem.
1  Change the audio output setting on the Blu-ray Disc player, DVD recorder\
 or  DVD player from Bitstream to PCM.
2 
Change input signal setting to “PCM ” in “Switching the input signal detection setting”.
—
24
The system does not work 
properly. •  The system does not work properly if you have connected the HDMI input and 
output terminals incorrectly. Turn the system off, unplug the AC power supply 
cord, and make the connection again. 9
Could watch TV (VIERA) 
when installed, but now 
cannot watch TV.•  When using this system in combination with the TV (VIERA) only, check if 
HDMI cable is not connected to “BD/DVD IN” of this system. If it is connected 
to “BD/DVD IN”, connect to “TO TV (ARC) OUT”. —
The sounds of the fi
 rst few 
seconds are cut off when 
playing back 7.1-channel 
LPCM signals.•  This may occur when playing back 7.1-channel LPCM signals of a Blu-ray 
disc. Press [ u SKIP] on the remote control of recorder or player to play back 
again from the beginning. —
5%
						

							VQT2R70
27
Maintenance
Unplug the AC power supply cord from the household AC outlet and wipe the system using a soft and dry cloth.
•  When the system is very dirty, wring the cloth soaked in water thoroughly, wipe the dirt and wipe moisture off with a dry cloth.
•  Do not use solvents such as benzine, thinner, alcohol, etc. because they may cause casing to deform and coating to come off.
•  Before using chemically treated cloth, read the instructions that come with the cloth carefully.
Digital signals that can be played on this system
Note
•  With HDMI connection, this system can play back multi-channel LPCM signals with sampling frequencies of over 48 kHz and PCM signals of over 96 kHz in 
addition to multi-channel LPCM of up to 48 kHz and PCM of up to 96 kHz. (If 
frequency exceeds these figures, playback equipment performs down-sampling 
and plays back as 48 kHz signals. However, playback may be impossible 
depending on the discs. See operating instructions of playback equipment for 
more information.)
• 
With the optical fiber connection, this system can play multi-channel LPCM signals 
with sampling frequencies of up to 48 kHz and PCM signals of up to 96 kH\
z.
• See “Glossary” (➜ page 28) for more detailed information on each signal.
„
 Dolby  Digital
  Blu-ray disc, DVD etc.
„  DTS
  Blu-ray disc, DVD etc.
„  PCM  (2-channel)
  CD, DVD audio etc.
„  Multi-channel LPCM (Linear PCM)
  Blu-ray disc, DVD audio etc. 
„  This system supports 3D, X.V. Color or 
Deep Color.
Troubleshooting and  other information
Troubleshooting guide/Digital signals that can be played on this system/\
Maintenance
Problem Possible solutionPages
HDMI
VIERA Link 
“HDAVI Control” does 
not function properly.
•  Confirm “VIERA Link “HDAVI Control” setting” is set to “ON ” (when the 
operation is linked).
  When it is “OFF ”, change to “ON ”.
• 
VIERA Link “HDAVI Control” does not function in Standby condition (HDMI off mode) 
when this system is turned off. See “Reducing Standby power consumption (In Standby 
condition (HDMI off mode))” and set to “ON ” (normal power consumption).
•  Check VIERA Link “HDAVI Control” settings of the connected equipment.
•  VIERA Link “HDAVI Control” may not function when you change the  connections for HDMI equipment, insert and remove the outlet, or during 
blackout. Do the following operations in this case:
 –   Turn on the TV (VIERA) again while all the equipment connected with HDMI 
cables is on. 
 –
  Set “VIERA Link “HDAVI Control” (HDMI equipment control)” of the TV (VIERA) to “OFF” and 
then set to “ON” again. (For details, refer to the operating instructions for the TV (VIERA).)
 –   Connect this system to the TV (VIERA) using the HDMI cable, switch the TV 
(VIERA) on, unplug this system’s AC power supply cord, and insert it into a 
household AC outlet again. 23
22
—
—
Even if multi-channel audio 
sources, such as DVD, Blu-ray 
disc, are played back, 
“ 
 DIGITAL” or “DTS” is not 
displayed.
•  When using VIERA Link “HDAVI Control” and the speaker is set to “TV”, press 
the VIERA Link button on the remote control of the TV (VIERA) and set the 
speaker to “Home Cinema”. 18
This system’s input automatically 
switches to “AUX2 / STB ”, but 
sound is not heard. 
Or unexpected sound from other 
equipment is heard.
•  After “Setting for automatically switching the input source to STB”, the 
connection might have been changed. Select OFF once and SET again. 10
Speakers
[WIRELESS LINK] 
indicator on the speakers 
does not light green.
Sounds are interrupted.•  When the [WIRELESS LINK] indicator is off, check the connection of the AC 
power supply cord of the speakers and check that each speaker is “ON”.
• 
If the [WIRELESS LINK] indicator does not change from red to green, the main unit and speakers 
are not linked. Make sure that the main unit is “ON”. Or make the speaker settings again.
• You may be using wireless headphones or the wireless LAN may be operating near this 
system. These symptoms may be remedied by slightly moving this system’s position.
12,13,15
13,15 —
Sound stops.
(The indicator blinks red 
and green alternately.)
The protection circuit 
is activated when some 
abnormality is detected, 
and turns off the system 
automatically.
•  Amplifier output is abnormal.
•  Straining of the speakers through excessive volume or power.
•  This may occur if you use the system in an extremely hot environment.
  D  Determine and correct the cause, then turn the system on.
(The protection circuit is reset.)
(Consult your dealer if the problem persists.) —
—
—
5%
						

							VQT2R70
28
Glossary
Optical
Using an optical fi ber cable for digital signal input/output from 
DVD, CD, etc., provides better sound quality for playback or 
recording compared to analog. Only possible with equipment 
that has an optical terminal.
PCM (Pulse Code Modulation)
This is one of the methods that enable analog sounds to be 
converted to digital sounds without compression. 
This method is used for music CD, etc.
Sampling frequency
Sampling is the process of converting the heights of sound wave 
(analog signal) samples taken at set periods into digits (digital 
encoding). Sampling frequency is the number of samples taken 
per second, so larger numbers mean faithful reproduction of the 
original sound.
Standby through function
When this system and the TV and Blu-ray Disc player/DVD 
recorder etc. are connected with HDMI cables, image/audio from 
Blu-ray Disc player/DVD recorder etc. can still be transmitted to 
the TV through this system even though the system is turned off.
This is useful when you want to enjoy late night viewing only 
with the television speakers.
Images recorded with x.v.Color or Deep Color are also 
supported.
Surround signal
Audio signal made up with front speakers, center speaker 
and surround speakers. For this system, surround signal is 
automatically played by Dolby Virtual Speaker.
WHISPER-MODE SURROUND
Even when the sound volume level is low, you can enjoy 
dynamic surround playback similarly as during normal playback. 
This is convenient when listening at night.
x.v.Color
This is a name of products compliant with ISO Standard for 
wider color space: “xvYCC”. This system supports x.v.Color.
1080p
This is one of the digital hi-vision images.
1080 is the number of effective scanning lines that constitute 
the actual screen. This enables every detail to be beautifully 
expressed. Images are less fl  ickered with progressive method 
that scans in order from the top. This system supports 1080p.
5.1-channel surround
Monaural and stereo use one channel and two channels 
respectively to reproduce sound, but 5.1-channel surround 
uses 5 speakers and 1 subwoofer. The 5 channels are: 1 center 
speaker, 2 front speakers, and 2 surround speakers at the 
side of or to the rear of the sitting position. Sound output of the 
subwoofer is much narrower than the other speakers, and so 
is considered as 0.1. This is called 5.1-channel surround when 
played through all 5.1 channels, and with this system you can 
achieve a similar effect with Dolby Virtual Speaker.
7.1-channel virtual surround
When playing back 7.1-channel LPCM signals with this function, 
you can enjoy wider sound fi  eld effects as if another speaker is 
added.
ARC (Audio Return Channel)
This function was added to HDMI Ver.1.4.
This sends digital audio signals from the HDMI input terminal of 
the TV, etc. to the HDMI output terminal of this system.
CPPM (Content Protection for Prerecorded Media)
This is the copyright protection technology which prevents fi
 le 
copy of DVD audio.
Decoder, Decode
Decoder is the device to enable us to hear audio data that is 
encoded on DVD, etc., as a normal audio signal. This process 
is called Decode.
Deep Color
This system can reproduce greater color gradation (4096 steps) 
when connected to a compatible TV and recorder, etc.
You can enjoy exceptionally rich, natural-looking colors, with 
smooth, detailed gradation and minimal color banding.
Dolby Digital
Digital sound compression technology developed by Dolby 
Laboratories.
Compatible with surround sound as well as 2-channel stereo 
sound. With this technology, you can keep massive amount of 
audio data in a disc effi  ciently.
Dolby Pro Logic 
This system can process not only Dolby Surround, but also 
other 2-channel sources to produce a 5.1-channel sound for 
a more realistic sound fi  eld. It is also possible to enhance old 
movies recorded in stereo with this dynamic 5.1-channel sound. 
This system uses Dolby Pro Logic   to add surround effects to 
stereo sources such as video cassettes and CDs.
Dolby Virtual  Speaker
This system allows you to enjoy a surround effect with two 
front speakers. This is not merely a “virtual surround” effect, but 
rather uses the optimal speaker arrangements and listening 
positions for 5.1-channel sound.
Down-sampling
This is the process of resampling by reducing the sampling rate 
of a signal that was sampled at a certain rate.
DTS (Digital Theater Systems)
Surround system used in most movie theaters. Separation 
works well between channels, resulting in realistic surround 
effects.
Dynamic range
Dynamic range is the difference between the lowest level of 
sound that can be heard above the noise of the equipment and 
the highest level of sound before distortion occurs.
HDMI (High Defi  nition Multimedia Interface)
HDMI enables you to transmit digital audio and video signals 
using a single cable.
You can also transmit control signals using HDMI connections.
Multi-channel LPCM (Linear PCM)
This is the uncompressed audio signal encoded digitally. Multi-
channel LPCM signals used for Blu-ray Disc, DVD audio, etc. 
offer playback with higher-sound quality. 
Up to 7.1-channel LPCM signals can be input to this system.
Glossary
Troubleshooting and  other information
5%
						

							VQT2R70
29
-If you see this symbol-
Information on Disposal in other Countries outside the 
European UnionThis symbol is only valid in the European Union. 
If you wish to discard this product, please contact 
your local authorities or dealer and ask for the 
correct method of disposal.
1.  Damage requiring service — The unit should be serviced by qualifi  ed service personnel if:
(a) The AC power supply cord or the plug has been damaged; or
(b) Objects or liquids have gotten into the unit; or
(c) The unit has been exposed to rain; or
(d)  The unit does not operate normally or exhibits a marked change  in performance; or
(e) The unit has been dropped or the cabinet damaged.
2.  Servicing — Do not attempt to service the unit beyond that  described in these operating instructions. Refer all other servicing to 
authorized servicing personnel.
3.  Replacement parts — When parts need replacing ensure the  servicer uses parts specifi  ed by the manufacturer or parts that 
have the same characteristics as the original parts. Unauthorized 
substitutes may result in fi  re, electric shock, or other hazards.
4.  Safety check — After repairs or service, ask the servicer to perform  safety checks to confi  rm that the unit is in proper working condition.
The servicer will require all components to service your system.
Therefore, should service ever be necessary, be sure to bring the 
entire system.
For product information or assistance with product operation:
In the U.S.A. and Puerto Rico, refer to “Customer Services Directory 
(United States and Puerto Rico)” on page 30.
In Canada, contact the Panasonic Canada Inc. Customer Care Centre 
at 1-800-561-5505, or visit the website (www.panasonic.ca), or an 
authorized Servicentre closest to you. DATE OF PURCHASE  __________________________________
DEALER NAME  _______________________________________
DEALER ADDRESS  ____________________________________
_____________________________________________________
TELEPHONE NUMBER  _________________________________
User memo:
The model number and serial number of this product can be found 
on either the back or the bottom of the unit.
Please note them in the space provided below and keep for future 
reference.
MODEL NUMBER  _______________________________________
SERIAL NUMBER  _______________________________________
SC-ZT2
Troubleshooting and 
other information
Product Service/Listening caution
Selecting fi  ne audio equipment such as the unit you’ve just purchased 
is only the start of your musical enjoyment. Now it’s time to consider 
how you can maximize the fun and excitement your equipment offers. 
This manufacturer and the Electronic Industries Association’s
Consumer Electronics Group want you to get the most out of your 
equipment by playing it at a safe level. One that lets the sound come 
through loud and clear without annoying blaring or distortion-and, most 
importantly, without affecting your sensitive hearing.
We recommend that you avoid prolonged exposure to excessive noise.
Sound can be deceiving. Over time your hearing “comfort level” adapts 
to higher volumes of sound. So what sounds “normal” can actually be 
loud and harmful to your hearing. 
Guard against this by setting your equipment at a safe level BEFORE 
your hearing adapts.
To establish a safe level:
Start your volume control at a low setting. 
Slowly increase the sound until you can hear it comfortably and 
clearly, and without distortion.
Once you have established a comfortable sound level: Set the dial and leave it there.
Taking a minute to do this now will help to prevent hearing damage or 
loss in the future. After all, we want you listening for a lifetime. •
•
•
EST. 1924
Manufactured under license from Dolby Laboratories. 
Dolby, Pro Logic, and the double-D symbol are trademarks of 
Dolby Laboratories. HDMI, the HDMI Logo, and High-Defi  nition Multimedia 
Interface are trademarks or registered trademarks of HDMI 
Licensing LLC in the United and other countries.
HDAVI Control™ is a trademark of Panasonic Corporation.
Manufactured under license under U.S. Patent #’s: 5,451,942; 
5,956,674; 5,974,380; 5,978,762; 6,487,535 & other U.S. and 
worldwide patents issued & pending. DTS and the Symbol 
are registered trademarks & DTS Digital Surround and the 
DTS logos are trademarks of DTS, Inc. Product includes 
software. © DTS, Inc. All Rights Reserved.
EZ Sync™ is a trademark of Panasonic Corporation.
VIERA Link™ is a trademark of Panasonic Corporation.
Product Service
Listening caution
   Product information
5%
						

							VQT2R70
30
Limited Warranty (ONLY FOR U.S.A. AND PUERTO RICO)
Limited Warranty (ONLY FOR U.S.A. AND PUERTO RICO)
Panasonic Consumer Electronics Company,
Division of Panasonic Corporation of North America
One Panasonic Way, Secaucus, New Jersey 07094
Panasonic Home Audio ProductsLimited Warranty
Limited Warranty Coverage (For USA and Puerto Rico Only)
If your product does not work properly because of a defect in materials or workmanship, 
Panasonic Consumer Electronics Company (referred to as “the warrantor”) will, for the 
length of the period indicated on the chart below, which starts with the date of original 
purchase (“warranty period”), at its option either (a) repair your product with new or 
refurbished parts, (b) replace it with a new or a refurbished equivalent value product, or 
(c) refund your purchase price. The decision to repair, replace or refund will be made by 
the warrantor.
During the “Labor” warranty period there will be no charge for labor. During the “Parts” 
warranty period, there will be no charge for parts. This Limited Warranty excludes both 
parts and labor for non-rechargeable batteries, antennas, and cosmetic parts (cabinet). 
This warranty only applies to products purchased and serviced in the United States or 
Puerto Rico. This warranty is extended only to the original purchaser of a new product 
which was not sold “as is”. 
Carry-In or Mail-In Service
To find a service center please visit http://www.panasonic.com/help or call 
1-800-211-PANA (7262).
When shipping the unit, carefully pack, include all accessories, and send it prepaid, 
adequately insured and preferably in the original carton. If Lithium Ion batteries are 
shipped by air the package must be labeled “Contains Lithium Ion Battery (No lithium 
metal)”. Damaged batteries are prohibited from shipment by US Mail. Batteries must be 
securely packed in a manner to prevent short-circuiting and a package cannot contain 
more than 3 Lithium Ion batteries.  Include a letter detailing the complaint, a return 
address and provide a daytime phone number where you can be reached. A valid 
registered receipt is required under the Limited Warranty.
IF REPAIR IS NEEDED DURING THE WARRANTY PERIOD, THE PURCHASER 
WILL BE REQUIRED TO FURNISH A SALES RECEIPT/PROOF OF PURCHASE 
INDICATING DATE OF PURCHASE, AMOUNT PAID AND PLACE OF PURCHASE. 
CUSTOMER WILL BE CHARGED FOR THE REPAIR OF ANY UNIT RECEIVED 
WITHOUT SUCH PROOF OF PURCHASE.
Limited Warranty Limits And Exclusions
This warranty ONLY COVERS failures due to defects in materials or workmanship, and 
DOES NOT COVER normal wear and tear or cosmetic damage. The warranty ALSO 
DOES NOT COVER damages which occurred in shipment, or failures which are caused 
by products not supplied by the warrantor, or failures which result from accidents, 
misuse, abuse, neglect, mishandling, misapplication, alteration, faulty installation, set-
up adjustments, misadjustment of consumer controls, improper maintenance, power 
line surge, lightning damage, modification, introduction of sand, humidity or liquids, 
Customer Services Directory (United States and Puerto Rico)
Obtain Product Information and Operating Assistance; locate 
your nearest Dealer or Service Center; purchase Parts and 
Accessories; or make Customer Service and Literature requests 
by visiting our Web Site at:
http://www.panasonic.com/help
or, contact us via the web at:
http://www.panasonic.com/contactinfo
You may also contact us directly at:
1-800-211-PANA (7262)
Monday-Friday 9am-9pm, Saturday-Sunday 10am-7pm EST
For hearing or speech impaired TTY users, TTY: 1-877-833-8855
Accessory Purchases (United States and Puerto Rico)
Purchase Parts, Accessories and Instruction Books online for all 
Panasonic Products by visiting our Web Site at: 
http://www.pstc.panasonic.com
Or, send your request by E-mail to:
[email protected]
You may also contact us directly at:
1-800-332-5368 (Phone)  1-800-237-9080 (Fax Only)
(Monday-Friday 9am-9pm EST)
Panasonic Service and Technology Company
20421 84th Avenue South, Kent, WA 98032
(We accept Visa, MasterCard, Discover Card, American Express, and 
Personal Checks)
For hearing or speech impaired TTY users, TTY: 1-866-605-1277
As of November 2009
Product or Part Name PartsLabor
Audio Products (except items below) 1 year1 year
DVD Home Theater System 1 year1 year
USB Reader-writer, PC Card Adapters 
(defective exchange) 1 year Not Applicable
Accessories: Headphones, cartridges, 
Microphones, Adapters 90 days 90 days
Rechargeable Batteries, DVD-RAM Disc 
(defective exchange)10 days Not Applicable
SD Memory Cards, Rechargeable Battery 
Packs (defective exchange)90 days Not Applicablecommercial use such as hotel, office, restaurant, or other business or rental use of the 
product, or service by anyone other than a Factory Service Center or other Authorized 
Servicer, or damage that is attributable to acts of God.
THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER “LIMITED 
WARRANTY COVERAGE”.
THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES 
RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH 
OF THIS WARRANTY. 
(As examples, this excludes damages for lost time, travel to and from the servicer, loss of or 
damage to media or images, data or other memory or recorded content. The items listed are 
not exclusive, but for illustration only.)
ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF 
MERCHANTABILITY, ARE LIMITED TO THE PERIOD OF THE LIMITED WARRANTY.
Some states do not allow the exclusion or limitation of incidental or consequential damages, 
or limitations on how long an implied warranty lasts, so the exclusions may not apply to you.
This warranty gives you specific legal rights and you may also have other rights which 
vary from state to state. If a problem with this product develops during or after the warranty 
period, you may contact your dealer or Service Center. If the problem is not handled to your 
satisfaction, then write to the warrantor’s Consumer Affairs Department at the addresses 
listed for the warrantor.
PARTS AND SERVICE, WHICH ARE NOT COVERED BY THIS LIMITED WARRANTY, ARE 
YOUR RESPONSIBILITY.
Troubleshooting and 
other information
5%