Panasonic Hybrid Control Panel Aw Rp501 Operating Instructions

							Hybrid Control PanelAW-RP501
Before attempting to connect or operate this product,
please read these instructions completely.
â 
						

							Warning:
This equipment generates and uses radio frequency ener-
gy and if not installed and used properly, i.e., in strict
accordance with the instruction manual, may cause harmful
interference to radio communications.    It has been tested
and found to comply with the limits for a Class A computing
device pursuant to Subpart J of Part 15 of FCC Rules,
which are designed to provide reasonable protection
against such interference when operated in a commercial
environment.
This digital apparatus does not exceed the Class A limits for
radio noise emissions from digital apparatus set out in the
Radio Interference Regulations of the Canadian Department
of Communications.
WARNING:
TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOIS
TURE.
The lightning flash with arrowhead sym-
bol, within an equilateral triangle, is
intended to alert the user to the pres-
ence of uninsulated dangerous voltage
within the products enclosure that may
be of sufficient magnitude to constitute a
risk of electric shock to persons.
The exclamation point within an equilat-
eral triangle is intended to alert the user
to the presence of important operating
and maintenance (servicing) instructions
in the literature accompanying the appli-
ance.The serial number of this product may be found on the bot-
tom of the unit.
You should note the serial number of this unit in the space
provided and retain this book as a permanent record of your
purchase to aid identification in the event of theft.
Model No.
Serial No.
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR BACK). NO USER SER-
VICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PER-
SONNEL.
CAUTIONRISK OF ELECTRIC SHOCK
DO NOT OPEN
SA 1965
SA 1966
For U.S.A
For CANADA 
						

							-1-
CONTENTS
FEATURES .......................................................................................................................................................................................... 2
PRECAUTIONS ................................................................................................................................................................................... 3
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS  ............................................................................................................ 4
INSTALLATION OF PAN/TILT HEAD  ................................................................................................................................................. 18
CONNECTIONS .................................................................................................................................................................................. 21
OPERATING PROCEDURES  .............................................................................................................................................................. 25
RACK MOUNTING  ............................................................................................................................................................................. 33
SPECIFICATIONS ............................................................................................................................................................................... 35
ACCESSORIES ................................................................................................................................................................................... 36 
						

							-2-
FEATURES• The Hybrid Control Panel AW-RP501 controls the
Pan/tilt Head (AW-PH300) and Color Video Camera
(WV-E550 or AW-E560).  With three coaxial cables (5C-
2V) and a single 10BASE-T straight cable (UTP catego-
ry 5), this panel performs various kinds of control on the
camera and pan/tilt head, and sends and receives
camera video signals and genlock signals.
• The maximum distance from this control panel to the
camera and pan/tilt head is 500 meters.• Head pan/tilt and lens zoom/focus can be controlled at
varying speeds with the servo control, and can be pre-
set at up to 10 points.
• With the auxiliary control input connector (AUX CON-
TROL IN), pan/tilt, zoom, focus, and iris operations can
be externally controlled. 
						

							-3-
• Use only with AC Adaptor, Model AW-PS301.
• Handle the control panel with care.
Dropping the control panel or subjecting it to a strong
shock can cause a failure or an accident.
• Operating temperature range –10°C to +45°C
Avoid using it in a cold place below –10°C or a hot
place above +45°C because low or high temperature
will adversely affect the parts inside.
• Switch power off before power cable connection or
disconnection.
Be sure to switch power off before connecting or dis-
connecting the power cable.
• Avoid outdoor use.
• Install the control panel more than 1 meter away
from the monitors.• Care
Pull out the power cable plug, and wipe the control
panel clean with a dry cloth. If it is extremely dirty, dip
a cloth into a diluted solution of kitchen detergent,
squeeze it hard, and wipe the product surfaces care-
fully.PRECAUTIONS
• Do not use benzine, paint thinner, or other volatile
liquids.
• When using a chemical duster, carefully read the
caution notes on its use.Note
Set the power control switch to the OFF position after
setting the lamp switch to the OFF position.  Halogen
lamp power will not be switched off if the AC adapter for
the AW-RP501 is disconnected or if the main circuit
breaker is opened while the halogen lamp is in use.Precautions in Using Halogen Lamp 
						

							-4-
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS
SPEED FOUCUS PA N  /  T I LT
ZOOM
TELE
WIDEFA R
LEFT
RIGHT UP
DOWN
NEAR
DEFON
OFF
POWEROPERATE
IRIS
BAR
CAMMODEGAIN AWC
SCENE
FILEABC
AT W
A
B
AUTO/AIW
ELC LOW MID
MANUON SC H
OFF HIGH AGC
OFF 1 / 100SHUTTER
ON
OFF
LAMP
MEMORY
ON
OFF AUTO
MANUON
OFFON
OFFON
OFF ON
OFFON
OFF
WIP
EXT ND OPH / F
1 .
2 .
3 .
4 .
G/L PHASE
PRESET
T.PED
CABLE COMP
Hybrid Control Panel AW-RP501
2 1345
67891090¡   180¡
0¡        270¡
LEVEL
TALLY
YC
nControl Panel 
						

							-5-
qPower Indicator [POWER]
Lights red when POWER ON/OFF Switch wis in the
ON position, and goes out when the same switch is set
to the OFF position.
wPower Control Switch [POWER, ON/OFF]
The camera and pan/tilt head are switched on when
this switch is set to the ON position.  (The power indica-
tor lights.)  The camera and pan/tilt head are partially
switched off when this switch is set to the OFF position.
Note:When the switch is set to the OFF position, the
camera is totally switched off but the communica-
tion line between the pan/tilt head and this control
panel remains live.  To disconnect all power sup-
ply, pull out the power plug from the electrical out-
let.
eOperating Indicator [OPERATE]
Lights green when communication begins normally
between the camera and the control panel, and goes
out if a communication error occurs.
rMode Selection Switch [MODE, BAR/CAM]
Used to select camera color bar signals or camera
video signals.  With the switch set to BAR, the control
panel outputs color bar signals from the video output
terminal.  When the switch is set to CAM, it outputs
camera video signals.tAGC Selection Switch [GAIN, AGC/MANU]
Keep this switch in the AGC position if you want to
keep automatic gain control.  When this switch is at
AGC, GAIN H/M/L Switch yis invalid.
yHigh Gain Selection Switch [GAIN, HIGH/MID/LOW]
This switch is valid only when GAIN AGC/MANU
Switch tis in the MANU position.  Normally, keep it in
the LOW position.  When the camera is used in a dark
place or when video output level is not high enough
even if the iris is wide open, set the switch to the MID
or HIGH position.
uElectronic Shutter Speed Selection Switch
[SHUTTER, ELC/ 1/100 /OFF]
Used to select a mode of camera electronic shutter
control.  With the switch in the ELC position, the elec-
tronic shutter is controlled and the camera sensitivity is
automatically adjusted when using the camera in a
bright place.  The shutter speed is 1/100 second when
the switch is in the 1/100 position.  The electronic shut-
ter is off when the switch is in the OFF position.
iWhite Balance ATW Selection Switch 
[AUTO/ATW, ATW]
When the switch is depressed, the camera keeps auto-
matically adjusting white balance.  The switch lights
when it is selected. 
						

							-6-
oWhite Balance Ach Selection Switch 
[AUTO/ATW, A]
When this switch is depressed, white balance will be
as stored in Channel A of the camera.  The switch
lights when it is selected.  When AWC Switch !1is
pressed after selecting AUTO/ATW, A, white balance
is automatically adjusted and stored in Channel A.
!0White Balance Bch Selection Switch 
[AUTO/ATW, B]
When this switch is depressed, white balance will be
as stored in Channel B of the camera.  The switch
lights when it is selected.  When AWC Switch !1is
pressed after selecting AUTO/ATW, B, white balance
is automatically adjusted and stored in Channel B.
!1Auto White Start Switch [AWC]
If this switch is pressed when AUTO/ATW A Switch o
or AUTO/ATW B Switch !0is selected, white balance is
automatically adjusted.  The adjustment results are
stored in Channel A or B.  This switch is invalid if the
MODE BAR/CAM Switch r is in the BAR position.
Auto Set Indicator !3flashes while AWC is in opera-
tion, and goes out when white balance has been prop-
erly adjusted.  Auto Set Indicator !3remains lit if white
balance adjustment fails.
Note:White balance may not be adjustable if there is
no white in the image being taken by the camera.
For details, refer to the Operating Instructions for
the Camera.!2Auto Black Start Switch [ABC]
When this switch is depressed, the lens iris is automat-
ically closed to set black balance.  Be sure to keep the
IRIS AUTO/MANU Switch @5in the AUTO position in
setting black balance.  Auto Set Indicator !3flashes
while ABC is in operation, and goes out when black
balance has been properly adjusted.  Auto Set
Indicator !3remains lit if black balance adjustment
fails.  Black balance adjustment may fail if the total
pedestal is too low.  In such a case, adjust the total
pedestal with T.PED Control !9(referring to the OPER-
ATING PROCEDURES at page 25) and try to adjust
black balance again.
!3Auto Set Indicator
This LED flashes during white balance or black bal-
ance adjustment with AWC Switch !1or ABC Switch !2
depressed, and goes out when the adjustment has
ended normally.  The LED remains lit if balance adjust-
ment fails.
!4Scene File Selection Switch [SCENE FILE, 1/2/3/4]
Select a scene file preset on the camera side.
Remember, however, that [4] is camera scene file
USER A or USER B (provided that WV-E550 or AW-
E560 is connected). 
						

							-7-
!5566Genlock Phase Control Switch 
[G/L PHASE, ON/OFF]
Used to adjust the genlock phase in operating the
camera in external sync mode.  Set the switch to the
ON position only when adjusting the genlock subcarri-
er phase or genlock horizontal phase.  Otherwise,
keep the switch in the OFF position.
!66Genlock Subcarrier Phase Coarse Switch 
[G/L PHASE, 0°/90°/180°/270°]
Used for coarse adjustment of the color phases of
genlock input and video output signals in operating the
camera in external sync mode.  Used in combination
with G/L PHASE SC Control !7, the switch has an
adjustment range of over 360°.  Set G/L PHASE
ON/OFF Switch !5to the ON position before adjusting
the color phases with this switch.
!7Genlock Subcarrier Phase Fine Control 
[G/L PHASE, SC]
Used for fine adjustment of the color phases of gen-
lock input and video output signals in operating the
camera in external sync mode.  Use this switch in
combination with G/L PHASE Coarse Switch !6.  Set
G/L PHASE ON/OFF Switch !5to the ON position
before adjusting the color phases with this switch.
!8G/L Horizontal Phase Adjustment Control 
[G/L PHASE, H]
Used to adjust the horizontal phases of genlock input
and video output signals in operating the camera inexternal sync mode.  Set G/L PHASE ON/OFF Switch
!5to the ON position before adjusting the horizontal
phases with this switch.
!9Total Pedestal Level Control [T. PED]
The set pedestal level of the camera’s Y (luminance)
signal can be adjusted.  This control is used in a sys-
tem of two or more cameras to adjust the pedestal lev-
els of these cameras.  The control may operate not
continuous sometimes due to digital signal processing.
@0Cable Compensation Luminance Control
[CABLE COMP, Y]
Used to adjust the Y (luminance) signal level of video
output signals as appropriate to the cable length
between the pan/tilt head and this control panel.  To
adjust it, first set MODE BAR/CAM Switch rto the
BAR position, then connect a waveform monitor, vec-
torscope, or other measuring instrument to the video
signal output.  If the cable between the pan/tilt head
and this control panel is longer than 300 meters, set
the cable compensation switch on the pan/tilt head to
the ON position in advance.  (For details, refer to the
OPERATING PROCEDURES at page 25 or to the
Operating Instructions for the Pan/tilt Head.)  First,
adjust the Y (luminance) signal level with this control,
then adjust the C (chrominance) signal level with
CABLE COMP C Control @1.  Repeat this until the video
output level of this control panel matches the camera
output level.
Turning this control changes not only the Y (luminance)
signal level but also the whole video signal level. 
						

							-8-
@1Cable Compensation Chrominance Control 
[CABLE COMP, C]
Used to adjust the C (chrominance) signal level of
video output signals as appropriate to the cable length
between the pan/tilt head and this control panel.  To
adjust it, first set MODE BAR/CAM Switch rto the
BAR position, then connect a waveform monitor, vec-
torscope, or other measuring instrument to the video
signal output.  If the cable between the pan/tilt head
and this control panel is longer than 300 meters, set
the cable compensation switch on the rotary head to
the ON position in advance.  (For details, refer to the
OPERATING PROCEDURES at page 25 or to the
Operating Instructions for the Pan/ Tilt Head.)  First,
adjust the Y (luminance) signal level with CABLE
COMP Y Control @0, then adjust the C (chrominance)
signal level with this control.  Repeat this until the video
output level of this control panel matches the camera
output level.
@2Tally Indicator [TALLY]
Lights red when a tally signal is input to TALLY
Terminal #9from a Special Effect Generator (SEG) or
video switcher.
@3Lamp Indicator [LAMP]
Lights red when LAMP ON/OFF Switch @4is in the ON
position.  Flashes if the lamp connected to the AC
Adapter (AW-PS300) for pan/tilt head is broken.  Goes
out when LAMP ON/OFF Switch @4is set to the OFF
position.Note:Use a halogen lamp of 250 W to 500 W to connect to
the Pan/tilt Head AC Adapter  (AW-PS300).  If a lamp
of lower than 250 W is connected to it, the LED may
flash when LAMP ON/OFF Switch @4is in the ON
position even though the lamp is not broken.
@4Lamp Switch [LAMP, ON/OFF]
Switches on and off the halogen lamp connected to
the lamp AC receptacle of the Pan/tilt Head AC
Adapter (AW-PS300).  Set it to the ON position to
switch the halogen lamp on (in which case, the lamp
LED flashes).  Set it to the OFF position to switch the
halogen lamp off.
@5Lens Iris Selection Switch [IRIS, AUTO/MANU]
When this switch is in the AUTO position, the lens iris is
automatically controlled according to the quantity of
light entering the lens.  When the switch is in the
MANU position, the iris can be manually controlled
over the range from the closed position to the fully
open position using IRIS LEVEL Control @6.
Set the switch to the MANU position in storing iris data
in PRESET Switches @8with MEMORY Switch @7.  If the
switch is in the AUTO position, iris data will not be
stored in the memory.