Panasonic Interchangeable Lens For Digital Camera H-ps45175 Operating Instructions

							Operating Instructions
INTERCHANGEABLE LENS FOR DIGITAL CAMERA
Model No.
H-PS45175
Before connecting, operating or adjusting this product, please read the instructions completely.
For USA and Puerto Rico assistance, please call: 1-800-211-PANA(7262) or, contact us via the web at: http://www.panasonic.com/contactinfoFor Canadian assistance, please call: 1-800-99-LUMIX (1-800-995-8649) or 
                                    send e-mail to: [email protected]
PP
VQT3R89
until 
2011/10/3
VQT3R89_ENG_SPA.book  1 ページ  ２０１１年８月２日　火曜日　午前１０時４８分 
						

							2VQT3R89ContentsInformation for Your Safety ..................................... 2Precautions ........................................................... 4
Supplied Accessories ............................................. 5
Attaching/Detaching the Lens ................................. 5
Names and Functions of Components ................... 7
Cautions for Use ..................................................... 9 Troubleshooting .................................................. 10
Specifications........................................................ 11
Limited Warranty................................................... 12-If you see this symbol-
THE FOLLOWING APPLIES ONLY IN CANADA.Information for Your SafetyKeep the unit as far away as possible from 
electromagnetic equipment (such as microwave 
ovens, TVs, video games, radio transmitters, 
high-voltage lines etc.).
≥ Do not use the camera near cell phones because 
doing so may result in noise adversely affecting 
the pictures and sound.
≥ If the camera is adversely affected by 
electromagnetic equipment and stops functioning 
properly, turn the camera off and remove the 
battery and/or the connected AC adaptor. Then 
reinsert the battery and/or reconnect the AC 
adaptor and turn the camera on.
Information on Disposal in other Countries 
outside the European Union
This symbol is only valid in the 
European Union.If you wish to discard this 
product, please contact your 
local authorities or dealer and 
ask for the correct method of 
disposal.
This Class B digital apparatus complies with 
Canadian ICES-003.
VQT3R89_ENG_SPA.book  2 ページ  ２０１１年８月２日　火曜日　午前１０時４８分 
						

							3
VQT3R89
The lens can be used with a digital camera 
compatible with the lens mount standard for the 
“Micro Four Thirds
TM System”.
≥ It cannot be mounted on the Four Thirds
TM mount 
specification camera.
≥ The digital camera illustrations in these operating 
instructions show DMC-G3 as an example.
≥ The appearance and specifications of products 
described in this manual may differ from the actual 
products you have purchased due to later 
enhancements.
≥
Micro Four Thirds
TM and Micro Four Thirds Logo 
marks are trademarks or registered trademarks of 
Olympus Imaging Corporation, in Japan, the United 
States, the European Union and other countries.
≥ Four Thirds
TM and Four Thirds Logo marks are 
trademarks or registered trademarks of Olympus 
Imaging Corporation, in Japan, the United States, 
the European Union and other countries.
≥ G MICRO SYSTEM is a lens exchange type 
digital camera system of LUMIX based on a Micro 
Four Thirds System standard.
≥ Other names of systems and products mentioned 
in these instructions are usually the registered 
trademarks or trademarks of the manufacturers 
who developed the system or product concerned.
THE FOLLOWING APPLIES ONLY IN THE U.S.A.FCC Note:This equipment has been tested and found to comply with the limits 
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection 
against harmful interference in a residential installation. This 
equipment generates, uses and can radiate radio frequency 
energy and, if not installed and used in accordance with the 
instructions, may cause harmful interference to radio 
communications. However, there is no guarantee that 
interference will not occur in a particular installation. If this 
equipment does cause harmful interference to radio or television 
reception, which can be determined by turning the equipment off 
and on, the user is encouraged to try to correct the interference 
by one or more of the following measures:●Reorient or relocate the receiving antenna.●Increase the separation between the equipment and receiver.●Connect the equipment into an outlet on a circuit different 
from that to which the receiver is connected.●Consult the dealer or an experienced radio/TV technician 
for help.Any unauthorized changes or modifications to this equipment 
would void the user’s authority to operate this device.This device complies with Part 15 of the FCC Rules. Operation is 
subject to the following two conditions: (1) This device may not cause 
harmful interference, and (2) this device must accept any interference 
received, including interference that may cause undesired operation.Responsible Party:
Panasonic Corporation of North America
One Panasonic Way
Secaucus, NJ 07094
Support Contact:
Panasonic Consumer Electronics Company
Telephone No.: 1-800-211-PANA (7262)
ENGLISH
VQT3R89_ENG_SPA.book  3 ページ  ２０１１年８月２日　火曜日　午前１０時４８分 
						

							4VQT3R89∫Lens Care≥Sand and dust can damage the lens. Make 
sure that no sand or dust gets inside the lens 
or the terminals when using the lens on a 
beach, etc.
≥ This lens is not waterproof. If drops of water 
get onto the lens, wipe the lens with a dry 
cloth.
≥ Do not press the lens with excessive force.
≥ When there is dirt (water, oil, and fingerprints, etc.) 
on the surface of the lens, the picture may be 
affected. Lightly wipe the surface of the lens with a 
soft, dry cloth before and after taking pictures.
≥ Do not place the lens mount facing downwards. 
Do not allow the lens contact points  1 to become 
dirty.
∫ About Condensation (Fogging of the 
Lens)≥Condensation occurs when there are differences 
in temperature and humidity as described below. 
Condensation can cause the lens to become dirty 
and lead to mold and malfunctioning, so exercise 
caution in the following situations:
– When the camera is brought indoors from outside 
during cold weather
– When the camera is brought into an air- conditioned car
– When cold air from an air conditioner is directly  blown onto the lens
– In humid places
≥ Put the camera into a plastic bag to allow it to 
acclimatize to the surr ounding temperature in 
order to prevent condensation. If condensation 
occurs, turn the power off and leave it for about 
two hours. Once the camera acclimatizes to the 
surrounding temperature the condensation will go 
away naturally.
PrecautionsVQT3R89_ENG_SPA.book  4 ページ  ２０１１年８月２日　火曜日　午前１０時４８分 
						

							5
VQT3R89
Supplied Accessories[Inspection to be performed when you unpack 
the unit]
When removing the unit from its packing box, check 
that the main unit and the supplied accessories are 
there and also check their external appearance and 
functions to verify that they have not sustained any 
damage during distribution and transportation.
If you discover any trouble, contact your vendor 
before using the product.
Product numbers correct as of August 2011. These 
may be subject to change.1
Lens Storage Bag
2
Lens Hood
3
Lens Cap
4
Lens Rear Cap(The lens rear cap and lens cap are attached to 
the interchangeable lens at the time of purchase.)
Attaching/Detaching the Lens≥Refer also to the camera’s operating instructions 
for attaching and detaching the lens.∫ Attaching the Lens≥Check that the camera is turned off.1 Turn the lens rear cap 
to detach it.A: Lens Rear Cap2Align the lens fitting 
marks
 B (red marks)
 on 
the camera body and the 
lens and then rotate the 
lens in the direction of 
the arrow until it clicks.
• Do not press the lens 
release button  C when you 
attach a lens.
• Do not try to attach the lens when holding it at an  angle to the camera body as the lens mount may 
get scratched.
• Check that the lens is attached correctly.
VFC4430 VFC4697 VYF3463123
VFC46054



VQT3R89_ENG_SPA.book  5 ページ  ２０１１年８月２日　火曜日　午前１０時４８分 
						

							6VQT3R89∫Detaching the Lens≥Check that the camera is turned off.While pressing on the 
lens release button  D, 
rotate the lens toward 
the arrow until it stops 
and then remove.• Attach the lens rear cap so  that the lens contact point 
does not get scratched.
• Attach the body cap to the camera so no dirt or  dust will get inside the main unit.∫ Attaching and Detaching 
the Lens Cap
Pinch the lens cap as 
shown in the figure to 
attach or detach.• Be careful not to lose the lens cap.
∫ Attaching the Lens Hood 
(Supplied Accessory)
Insert the lens hood into 
the lens, and turn in the 
direction of the arrow 
until it stops.E: Fit to the mark∫Temporarily Storing the Lens Hood1 Turn the lens hood in the direction of the 
arrow to detach it.2 Reverse the lens hood and then attach it 
in the same way as shown previously.
 
VQT3R89_ENG_Body.fm  6 ページ  ２０１１年８月３日　水曜日　午後１２時１３分 
						

							7
VQT3R89
• When taking pictures with the flash with the lens hood attached, the lower portion of the screen 
may turn dark (vignetting effect) and the control 
of the flash may be disabled because the photo 
flash may be obscured by the lens hood. We 
recommend detaching the lens hood.
• When using the AF assist lamp in the dark, 
detach the lens hood.∫ Attaching Filters≥Vignetting may occur if using 2 or more 
MC protectors (optional: DMW-LMC46), 
PL filters (optional: DMW-LPL46) or ND filters 
(optional: DMW-LND46), or if using thick 
protectors and/or filters.
≥ The filter may become impossible to remove if 
excessively tightened, so please refrain from 
tightening it too strongly.
≥ It is possible to attach the lens cap with the filter 
already attached.
≥ You cannot attach a conversion lens or adaptor to 
this lens. A filter may be used, but attaching any 
other element may cause damage to the lens.
Names and Functions of Components1 Lens surface
2 Focus ring
Rotate to focus when taking pictures with 
manual focus.
5 6
2
1
34
VQT3R89_ENG_SPA.book  7 ページ  ２０１１年８月２日　火曜日　午前１０時４８分 
						

							8VQT3R893Zoom ring
Rotate the zoom ring to the [T] 
(Tele side) or [W] (Wide side).
[T]: To make subjects appear 
closer use (Tele)
[W]: To make subjects appear  further away use (Wide)
• The zoom speed varies depending on the 
speed to rotate the ring.
4 Zoom lever
Move the zoom lever to the [T] 
(Tele side) or [W] (Wide side).
[T]: To make subjects appear 
closer use (Tele)
[W]: To make subjects appear 
further away use (Wide)
• The zoom speed varies depending on the  range over which the z oom lever is moved.
• If you take your finger off the zoom lever during  zoom operation while recording a motion 
picture, the operation sound may be recorded. 
When returning the zoom lever to the original 
position, move it quietly.
5 Contact points
6 Lens fitting mark
Note
≥ Zoom speed will be slower than normal when 
recording a motion picture.
≥ When flash recording with a close subject, the 
light of the flash will be blocked by the lens and 
part of the picture may be dark. Check the 
distance from the subject when recording.
≥ There is no indication of focal length on the lens. 
The focal length is displayed on the screen of the 
digital camera when attached to the compatible 
digital camera. Focal length is not displayed on 
the digital camera that is not compatible. For 
details on the digital camera used, refer to the 
website.
http://panasonic.jp/support/global/cs/dsc/
 
(This Site is English only.)
5
8
TW
VQT3R89_ENG_SPA.book  8 ページ  ２０１１年８月２日　火曜日　午前１０時４８分 
						

							9
VQT3R89
Cautions for UseTake care not to drop or knock the lens. Also 
take care not to put a lot of pressure on the lens.
≥Take care not to drop the bag that you inserted the 
lens in as it may damage the lens. The camera 
may stop operating normally and pictures may no 
longer be recorded.
When using pesticides and other volatile 
substances around the camera make sure that 
they do not get onto the lens.
≥If such substances get  onto the lens they can 
damage the exterior case or cause the paint to peel.Do not carry the unit when it is still attached to 
the camera body.
≥ Under no circumstances should the unit be stored 
in any of the following locations since doing so 
may cause problems in operation or 
malfunctioning.
– In direct sunlight or on a beach in summer
– In locations with high temperatures and humidity  levels or where the changes in temperature and 
humidity are acute – In locations with high concentrations of sand, 
dust or dirt
– Where there is fire
– Near heaters, air conditioners or humidifiers
– Where water may make the unit wet
– Where there is vibration
– Inside a vehicle
≥ Refer also to the operating instructions of the 
digital camera.
≥ When the unit is not going to be used for a 
prolonged period, we recommend storing with a 
desiccant (silica gel). Failure to do so may result in 
performance failure caused by mold, etc. It is 
recommended that you check the unit’s operation 
prior to use.
≥ Do not leave the lens in  contact with rubber or 
plastic products for extended periods of time.
≥ Do not touch the lens contact point. Doing so can 
cause failure of the unit.
≥ Do not disassemble or alter the unit.VQT3R89_ENG_SPA.book  9 ページ  ２０１１年８月２日　火曜日　午前１０時４８分 
						

							10VQT3R89Do not use benzine, thinner, alcohol or other 
similar cleaning agents to clean the lens glass or 
exterior cabinet.
≥Using solvents can damage  the lens or cause the 
paint to peel.
≥ Wipe off any dust or fingerprints with a soft, dry 
cloth.
≥ Use a dry, dust cloth to remove dirt and dust on 
the zoom ring and focus ring.
≥ Do not use a household detergent or a chemically 
treated cloth. A sound is heard when the camera is turned on 
or off.
≥
This is the sound of lens or aperture movement 
and is not a malfunction.
When this lens is attached to digital camera, 
stabilizer function cannot be turned off or 
stabilizer function does not work.
≥ The Optical Image Stabilizer function of this lens 
only works correctly with supported cameras.
> When older Panasonic digital cameras (DMC-
GF1, DMC-GH1, DMC-G1) are used, 
[STABILIZER] in the [REC] mode menu cannot be 
set to [OFF]. It is recommended to update the 
firmware of the digital camera at the following 
website. 
http://panasonic.jp/support/global/cs/dsc/
download/
>When using this lens with another make of digital 
cameras, the Optical Image Stabilizer function will 
not work. (As of August 2011)
For details, contact the respective company.Troubleshooting
VQT3R89_ENG_SPA.book  10 ページ  ２０１１年８月２日　火曜日　午前１０時４８分