Panasonic Interchangeable Lens For Digital Camera H-x015 Owners Manual

							Owner’s Manual
INTERCHANGEABLE LENS FOR DIGITAL CAMERA
Model No.
H-X015
PP
until 
2014/4/28
Please read these instructions carefully before using this product, and save this manual for future use.If you have any questions, visit: 
USA : www.panasonic.com/support
Canada : www.panasonic.ca/english/support
SQT0243F0414KD0
SQT0243_ENG_SPA.book  1 ページ  ２０１４年４月１１日　金曜日　午前９時３３分 
						

							2SQT0243 (ENG)ContentsInformation for Your Safety ..................................... 2Precautions ........................................................... 4
Supplied Accessories ............................................. 5
Names and Functions of Components ................... 6
Attaching/Detaching the Lens ................................. 7
Cautions for Use ................................................... 10 Troubleshooting .................................................. 10
Specifications........................................................ 11
Limited Warranty................................................... 12-If you see this symbol-
THE FOLLOWING APPLIES ONLY IN CANADA.Information for Your SafetyKeep the unit as far away as possible from 
electromagnetic equipment (such as microwave 
ovens, TVs, video games, radio transmitters, 
high-voltage lines etc.).
≥ Do not use the camera near cell phones because 
doing so may result in noise adversely affecting 
the pictures and sound.
≥ If the camera is adversely affected by 
electromagnetic equipment and stops functioning 
properly, turn the camera off and remove the 
battery and/or the connected AC adaptor. Then 
reinsert the battery and/or reconnect the AC 
adaptor and turn the camera on.
The lens can be used with a digital camera 
compatible with the lens mount standard for the 
“Micro Four Thirds
TM System”.
≥ It cannot be mounted on the Four Thirds
TM mount 
specification camera.
Information on Disposal in other Countries 
outside the European Union
This symbol is only valid in the 
European Union.If you wish to discard this 
product, please contact your 
local authorities or dealer and 
ask for the correct method of 
disposal.
CAN ICES-3(B)/NMB-3(B)
SQT0243_ENG_SPA.book  2 ページ  ２０１４年４月１１日　金曜日　午前９時３３分 
						

							3
(ENG) SQT0243
≥The digital camera illustrations in this owner’s 
manual show DMC-GM1 as an example.
≥ The appearance and specifications of products 
described in this manual may differ from the actual 
products you have purchased due to later 
enhancements.
≥ Micro Four Thirds
TM and Micro Four Thirds Logo 
marks are trademarks or registered trademarks of 
Olympus Imaging Corporation, in Japan, the 
United States, the European Union and other 
countries.
≥ Four Thirds
TM and Four Thirds Logo marks are 
trademarks or registered trademarks of Olympus 
Imaging Corporation, in Japan, the United States, 
the European Union and other countries.
≥ G MICRO SYSTEM is an interchangeable lens 
type digital camera system of LUMIX based on a 
Micro Four Thirds System standard.
≥ LEICA is a registered trademark of Leica 
Microsystems IR GmbH. 
SUMMILUX
 is a 
registered trademark of Leica Camera AG. The 
LEICA DG lenses are manufactured using 
measurement instruments and quality assurance 
systems that have been certified by Leica Camera 
AG based on the company’s quality standards.
≥ Other names of systems and products mentioned 
in these instructions are usually the registered 
trademarks or trademarks of the manufacturers 
who developed the system or product concerned.
THE FOLLOWING APPLIES ONLY IN THE U.S.A.FCC Note:This equipment has been tested and found to comply with the limits 
for a Class B digital device, pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection 
against harmful interference in a residential installation. This 
equipment generates, uses and can radiate radio frequency 
energy and, if not installed and used in accordance with the 
instructions, may cause harmful interference to radio 
communications. However, there is no guarantee that 
interference will not occur in a particular installation. If this 
equipment does cause harmful interference to radio or 
television reception, which can be determined by turning the 
equipment off and on, the user is encouraged to try to correct 
the interference by one or more of the following measures:●Reorient or relocate the receiving antenna.●Increase the separation between the equipment and receiver.●Connect the equipment into an outlet on a circuit different 
from that to which the receiver is connected.●Consult the dealer or an experienced radio/TV technician 
for help.Any unauthorized changes or modifications to this equipment 
would void the user’s authority to operate this device.This device complies with Part 15 of the FCC Rules. Operation is 
subject to the following two conditions: (1) This device may not cause 
harmful interference, and (2) this device must accept any interference 
received, including interference that may cause undesired operation.Responsible Party:
Panasonic Corporation of North America
Two Riverfront Plaza, Newark, NJ 07102-5490
Support Contact: 
http://www.panasonic.com/contactinfo
ENGLISH
SQT0243_ENG_SPA.book  3 ページ  ２０１４年４月１１日　金曜日　午前９時３３分 
						

							4SQT0243 (ENG)∫Lens Care≥Sand and dust can damage the lens. Make 
sure that no sand or dust gets inside the lens 
or the terminals when using the lens on a 
beach, etc.
≥ The lens is neither waterproof nor splash-
proof. If drops of water get onto the lens, wipe 
the lens with a dry cloth.
≥ Do not press the lens with excessive force.
≥ When there is dirt (water, oil, and fingerprints, etc.) 
on the surface of the lens, the picture may be 
affected. Lightly wipe the surface of the lens with a 
soft, dry cloth before and after taking pictures.
≥ Do not place the lens mount facing downwards. 
Do not allow the lens contact points  1 to become 
dirty.
∫ About Condensation (Fogging of the 
Lens)≥Condensation occurs when there are differences 
in temperature and humidity as described below. 
Condensation can cause the lens to become dirty 
and lead to mold and malfunctioning, so exercise 
caution in the following situations:
– When the camera is brought indoors from outside 
during cold weather
– When the camera is brought into an air- conditioned car
– When cold air from an air conditioner is directly  blown onto the lens
– In humid places
≥ Put the camera into a plastic bag to allow it to 
acclimatize to the surr ounding temperature in 
order to prevent condensation. If condensation 
occurs, turn the power off and leave it for about 
two hours. Once the camera acclimatizes to the 
surrounding temperature the condensation will go 
away naturally.
PrecautionsSQT0243_ENG_SPA.book  4 ページ  ２０１４年４月１１日　金曜日　午前９時３３分 
						

							5
(ENG) SQT0243
Supplied Accessories[Inspection to be performed when you unpack 
the unit]
When removing the unit from its packing box, check 
that the main unit and the supplied accessories are 
there and also check their external appearance and 
functions to verify that they have not sustained any 
damage during distribution and transportation.
If you discover any trouble, contact your vendor 
before using the product.
Product numbers correct as of April 2014. These 
may be subject to change.≥
The lens cap, lens rear  cap, and decoration ring 
are attached to the lens at the time of purchase. In 
addition, the lens hood cap is attached to the lens 
hood.VFC4456
:SFC0191 :SFC0190:SFC0090
:SFC0089
:SFC0133
:SFC0093
SYF0001
2
1
6
5 34
VFC4605
1
Lens Pouch 4Lens Cap
2 Lens Hood
A: Black
B : Silver 5
Lens Rear Cap
3 Lens Hood Cap
A: Black
B : Silver 6
Decoration ring
A: Black
B : Silver
SQT0243_ENG_SPA.book  5 ページ  ２０１４年４月１１日　金曜日　午前９時３３分 
						

							6SQT0243 (ENG)Names and Functions of Components1Lens surface
2 Decoration ringRemove this cover when using the lens hood.3Aperture ringRotate this to adjust the aperture value.
≥If you set the camera to Aperture-Priority AE 
Mode or Manual Exposure Mode, the aperture 
value of the ring will be enabled.
≥ If you set the position of the aperture ring to [A], 
the aperture value of the camera will be enabled.
≥ When the aperture ring is enabled, check if the 
aperture value has changed after attaching or 
removing the decoration ring.
4 Focus ringRotate to focus when taking pictures with manual 
focus (MF).5[AF/MF] switchThis allows you to switch between Auto Focus (AF) 
and Manual Focus (MF). If you set [MF], you can 
use the focus ring to adjust the focus.
≥When either the [AF/MF] switch of the lens or the 
setting of the camera is set to [MF], Manual Focus 
(MF) is enabled.6 Lens fitting mark
7 Contact points
Note
≥ When using this lens and the flash to record a 
subject very close to the camera, it is possible that 
a darker shadowed area may appear in the lower 
portion of the picture. This situation is not a 
malfunction and is caused when the flash is 
partially blocked by the l ens. This situation may be 
worsened when the lens hood is used.
≥In very quiet situations Auto Focus operating sounds 
may be recorded during motion picture recording. 
This is not a malfunction. In such situations, 
switching to Manual Focus will improve the situation.≥ The aperture can be adjusted with the aperture 
ring only when a Panasonic digital camera is 
attached to the lens. (As of April 2014)
1234 5 6 7
SQT0243_ENG_SPA.book  6 ページ  ２０１４年４月１１日　金曜日　午前９時３３分 
						

							7
(ENG) SQT0243
Attaching/Detaching the LensCheck that the camera is 
turned off.
≥Remove the lens rear cap 
from the lens.∫ Attaching the LensAlign the lens fitting 
marks
 A on the 
camera body and the 
lens and then rotate 
the lens in the 
direction of the 
arrow until it clicks.
• Do not press the lens release button  B when 
you attach a lens.
• Do not try to attach the lens when holding it at an  angle to the camera body as the lens mount may 
get scratched.
• Check that the lens is attached correctly.
• Be sure to remove the lens cap when recording.
∫ Detaching the LensWhile pressing on the 
lens release button  B, 
rotate the lens toward 
the arrow until it stops 
and then remove.• Attach the lens rear cap 
so that the lens contact point does not get 
scratched.
• Attach the body cap to the camera so no dirt or 
dust will get inside the main unit.
SQT0243_ENG_SPA.book  7 ページ  ２０１４年４月１１日　金曜日　午前９時３３分 
						

							8SQT0243 (ENG)∫Attaching the Lens Hood 
(Supplied Accessory)≥Before attaching the lens 
hood, make sure to remove 
the lens cap. The lens hood 
cannot be attached unless 
you remove the lens cap.1 Rotate the decoration ring 
C in the 
direction of the arrow to remove it.
2 Align the mounting index 
D on the lens 
hood with the mark on the tip of the lens.
3 Rotate the lens hood in the direction of  the arrow until it clicks into place, and 
align the stop position 
E on the lens 
hood with the index on the tip of the lens.
Note
≥ When using this lens and the flash to record a 
subject very close to the camera, it is possible that 
a darker shadowed area may appear in the lower 
portion of the picture. This situation is not a 
malfunction and is caused when the flash is 
partially blocked by the l ens. This situation may be 
worsened when the lens hood is used.
≥ When using the AF assist lamp in the dark, detach 
the lens hood.
≥ Make sure to remove the lens hood cap when 
recording an image.
23
SQT0243_ENG_SPA.book  8 ページ  ２０１４年４月１１日　金曜日　午前９時３３分 
						

							9
(ENG) SQT0243
∫Attaching the decoration ring≥Before attaching the decoration ring, make 
sure to remove the lens cap.1 Align the mounting position
 G
 on the 
decoration ring with a position 
approximately 90 x away from the lens 
fitting mark 
F 
to fit the decoration ring 
into place.
2 Rotate the decoration ring in the  direction of the arrow to align the 
mounting position 
G on the decoration 
ring with the lens fitting mark 
F. ∫
Attaching Filters
≥Vignetting may occur if using 2 or more 
MC protectors (optional: DMW-LMC46), PL filters 
(optional: DMW-LPL46) or ND filters (optional: 
DMW-LND46), or if using thick protectors and/or 
filters.
≥ The filter may become impossible to remove if 
excessively tightened, so please refrain from 
tightening it too strongly.
≥ It is possible to attach the lens cap with the filter 
already attached.
≥ When the lens hood is attached to this lens, you 
cannot attach a filter to it.
≥ You cannot attach a conversion lens or adaptor to 
this lens. A filter may be used, but attaching any 
other element may cause damage to the lens.
12SQT0243_ENG_SPA.book  9 ページ  ２０１４年４月１１日　金曜日　午前９時３３分 
						

							10SQT0243 (ENG)Cautions for UseTake care not to drop or knock the lens. Also 
take care not to put a lot of pressure on the lens.
≥Take care not to drop the bag that you inserted the 
lens in as it may strongly shock the lens. The camera 
may stop operating normally and pictures may no 
longer be recorded. Also, the lens may be damaged.≥When carrying the digital camera with the lens 
attached, hold both the digital camera and the lens.When using pesticides and other volatile 
substances around the camera make sure that 
they do not get onto the lens.
≥If such substances get onto the lens they can 
damage the exterior case or cause the paint to peel.Do not point the lens at the sun or other strong 
light sources.
≥This could cause the lens to collect an excessive 
amount of light, resulting in fire and malfunction.
≥Under no circumstances should the unit be stored in 
any of the following locations since doing so may 
cause problems in operation or malfunctioning.– In direct sunlight or on a beach in summer– In locations with high temperatures and humidity levels or  where the changes in temperature and humidity are acute– In locations with high concentrations of sand, dust or dirt– Where there is fire
– Near heaters, air conditioners or humidifiers
– Where water may make the unit wet
– Where there is vibration – Inside a vehicle
≥
Refer also to the owner’s manual of the digital camera.≥When the unit is not going to be used for a prolonged 
period, we recommend storing with a desiccant (silica 
gel). Failure to do so may result in performance 
failure caused by mold, etc. It is recommended that 
you check the unit’s operation prior to use.≥ Do not leave the lens in contact with rubber or 
plastic products for extended periods of time.
≥ Do not touch the lens contact point. Doing so can 
cause failure of the unit.
≥ Do not disassemble or alter the unit.
Do not use benzine, thinner, alcohol or other 
similar cleaning agents to clean the lens glass or 
exterior cabinet.
≥ Using solvents can damage the lens or cause the 
paint to peel.
≥Wipe off any dust or fingerprints with a soft, dry cloth.≥ Use a dry, dust cloth to remove dirt and dust on 
the focus ring and the aperture ring.
≥ Do not use a household detergent or a chemically 
treated cloth.When I turn on or off the camera or when I shake the 
lens, I hear a sound, for example a rattling sound.
When I take pictures of a bright subject, such as a 
subject outside, or when I take pictures with a large 
aperture value, the lens makes a sound.≥This is the sound of lens or aperture movement and is 
not a malfunction.Troubleshooting
SQT0243_ENG_SPA.book  10 ページ  ２０１４年４月１１日　金曜日　午前９時３３分