Panasonic Kx Taw848 Installation Manual

2.2 Installation of the PBX
Installation Manual 41
Cable Handling
1.
Attach the strap included with the card to one of the connected cables.
2.Bind all the connected cables together using the strap.
3.Repeat the procedure for other cards.
Strap 

2.2 Installation of the PBX
42 Installation Manual
4.Attach the main strap (included with the PBX) to any of the 5 rails depending on your preference.
1
2
Main Strap 

2.2 Installation of the PBX
Installation Manual 43
5.Bind all the connected cables together using the main strap, and then close the cable cover. For 
how to close the cable cover, refer to 2.2.3 Opening/Closing the Covers.
Notes
 For safety reasons, do not stretch, bend, or pinch the cables.
 If you prefer, you can cut the other side of the cable cover and run the cables through that 
opening. For safety reasons, smooth the cut edges.
Cable Cover
Main Strap 

2.2 Installation of the PBX
44 Installation Manual
Removing the Optional Service Cards
1.Loosen the extension bolt.
2.Holding the protrusions of the card, pull the card in the direction of the arrows. 
CAUTION
When removing the optional service cards, do not put pressure on any parts of the main board. Doing 
so may result in damage. 

2.2 Installation of the PBX
Installation Manual 45
2.2.7 Types of Connectors
Connector Type Pin Number Used for
(Twisted pair cable) DPH4 (TAW84861)
 HLC4 (TAW84871)
 SLC8 (TAW84874)
 PLC4 (TAW84875)
 PLC8 (TAW84876)
 LCOT4 (TAW84880)
 Hybrid Ports (Main Board)
 DPH4 (KX-TAW84861)
 Main Board
 Main Board
 Main Board (Pager port, MOH port)
RJ11
4       1
10-pin
Terminal Block8-pin
Terminal Block8 1
10 1
RS-232C
6           9 1                5
USB
2
 31
 4
Mini Plug+
- 

2.2 Installation of the PBX
46 Installation Manual
2.2.8 Wall Mounting (KX-TAW848)
Mounting on Wooden Wall
1.Place the reference for wall mounting on the wall to mark the three screw positions.
2.Install the screws and washers (included) in the wall.
Notes
 Make sure that the screw heads are at the same distance from the wall.
 Install the screws perpendicular to the wall.
3.Hook the main unit on the screw heads.
Notes
 Do not block the openings of the cabinet. Leave at least 20 cm (8 in) of space...

2.2 Installation of the PBX
Installation Manual 47
Mounting on Concrete or Mortar Wall
CAUTION
Drive mounting screws into the wall. Be careful to avoid touching any metal laths, wire laths or metal 
plates in the wall.
1.Place the reference for wall mounting on the wall to mark the three screw positions.
2.Install three anchor plugs (user-supplied) in the wall.
3.Install the screws (included) in the wall.
4.Hook the main unit on the screw heads.
250 mm
(9-13/16 in)
130 mm (5-1/8 in)
HammerAnchor Plug8...

2.2 Installation of the PBX
48 Installation Manual
Notes
 Do not block the openings of the cabinet. Leave at least 20 cm (8 in) of space above and 10 cm (4 
in) to the sides of the PBX for ventilation.
 Make sure that the surface behind the cabinet is flat and free of obstacles, so that the openings on 
the back of the cabinet will not be blocked.
 Be careful not to drop the cabinet.  

2.2 Installation of the PBX
Installation Manual 49
2.2.9 Wall Mounting (AC Adaptor)
Mounting on Wooden Wall
1.Place the reference for wall mounting (on the following page) on the wall to mark the two screw 
positions.
2.Install the screws and washers (included) in the wall.
Notes
 Make sure that the screw heads are at the same distance from the wall.
 Install the screws perpendicular to the wall.
3.Hook the AC adaptor on the screw heads.
Note
Be careful not to drop the AC adaptor.
110 mm
(4-5/16 in)...

2.2 Installation of the PBX
50 Installation Manual
Mounting on Concrete or Mortar Wall
CAUTION
Drive mounting screws into the wall. Be careful to avoid touching any metal laths, wire laths or metal 
plates in the wall.
1.Place the reference for wall mounting (on the following page) on the wall to mark the two screw 
positions.
2.Install two anchor plugs (user-supplied) in the wall.
3.Install the screws (included) in the wall.
4.Hook the AC adaptor on the screw heads.
Note
Be careful not to drop the AC...