Panasonic Kx Tgd210 Operating Instructions Manual

Resetting to a pre-recorded greeting
m
e
ssage
If you want to use a pre-recorded greeting
message once you record your own greeting
message, you need to erase your own
greeting message.
1 MMENU N#304
2 MYES N a  M OFF N Playing back the greeting
m
e

ssage
1 MMENU N#303
2 To exit, press  MOFF N. Listening to messages
Using the base unit
W
h

en new messages have been recorded:
– M N
 on the base unit flashes.
– “N

ew message ” is displayed.
Press  M N
 (PLAY).
R I

f new messages have been recorded,...

Key Operation
*6 Reset to a pre-recorded
gr
eeting message *1 If pressed within the first 5 seconds of a
me

ssage, the previous message is
played.
*2 To resume playback: Mb N:  “Playback ” a  M SELECT N
*3 You can also erase as follows: MPAUSE N a  M b N:  “Erase ” a
M SELECT N a  M b N:  “Yes ” a  M SELECT NCalling back (Caller ID subscribers
o
n

ly)
1 Press  MPAUSE N during playback.
2 Mb N:  “Call back ” a  M SELECT N
n  Editing the number before calling back
1 Press  MPAUSE N during playback.
2 Mb...

Remote commands
Yo
u can press dial keys to access certain
answering system functions without waiting for
the voice guidance to prompt you. Key Operation
1 Repeat message (during
pl

ayback) *1
2 Skip message (during playback)
4 Play new messages
5 Play all messages
9 Stop playback *
2
S
 tart voice guidance *3
0 Turn answering system off
*4 Erase currently playing message
*5 Erase all messages
*# End remote operation
( o

r hang up) *1 If pressed within the first 5 seconds of a
me

ssage, the previous...

R
To use this unit’s answering system rather
t han the voice mail service provided by
your service provider/telephone company,
please contact your service provider/
telephone company to deactivate your
voice mail service.
If your service provider/telephone company
cannot do this:
– Set this unit’s  “Ring count ” setting so
that this unit’s answering system
answers calls before the voice mail
service of your service provider/
telephone company does. It is necessary
to check the number of rings required...

Voice mail service
V o
ice mail is an automatic answering service
offered by your service provider/telephone
company. After you subscribe to this service,
your service provider/telephone company’s
voice mail system answers calls for you when
you are unavailable to answer the phone or
when your line is busy. Messages are
recorded by your service provider/telephone
company, not your telephone. Please contact
your service provider/telephone company for
details of this service.
Important:
R To use the voice...

Note:
R
If
 the handset still indicate there are new
messages even after you have listened to
all new messages, turn it off by pressing
and holding  # until the handset beeps. Wall mounting
N o

te:
R Make sure that the wall and the fixing
method are strong enough to support the
weight of the unit. Base unit
1
Le

ad the telephone line cord through the
hole in the wall mounting adaptor in the
direction of the arrow. 2
Tuck the telephone line cord inside the
w
 all mounting adaptor ( A). Connect the
AC...

Fit the slots of the unit onto the
c
o
rresponding wall phone plate tabs
for ( ) and ( ) respectively.
To remove the wall mounting adaptor
W
h

ile pushing down the release levers ( A),
remove the adaptor ( B). Charger
D
r

ive the screws ( ) (not supplied) into the
w a

ll.  27.2 mm (1 
1
/1 6 
 inches) For assistance, please visit http://www.panasonic.com/help
37Useful Information
TGD2xx_(en_en)_1209_ver.040.pdf   372013/12/09   10:59:203 4 3
123
4
4 A
BA 1 2 1 2  

Error messages
Display message Cause/solution
Base no power
o r
N
o link. Re-connect base
AC adaptor. R
The handset has lost communication with the base
u nit. Move closer to the base unit and try again.
R Unplug the base unit’s AC adaptor to reset the unit.
Reconnect the adaptor and try again.
R The handset’s registration may have been canceled.
Re-register the handset (page 27).
Busy RThe called unit is in use.
R O

ther units are in use and the system is busy. Try
again later.
R The handset you are...

Troubleshooting
I f
 you still have difficulties after following the instructions in this section, disconnect the base unit’s
AC adaptor, then reconnect the base unit’s AC adaptor. Remove the batteries from the handset,
and then insert the batteries into the handset again. General use
Problem Cause/solution
The handset does not turn on
e v

en after installing charged
batteries. R
Place the handset on the base unit or charger to turn on
t he handset.
The unit does not work. RMake sure the batteries are...

Problem Cause/solution
I fully charged the batteries, but
–  still flashes,
–  is displayed, or
– t
he operating time seems to
be shorter. R
Clean the battery ends ( ,  ) and the charge contacts
wi

th a dry cloth and charge again.
R It is time to replace the batteries (page 10). Making/answering calls, intercom
Problem Cause/solution
 is displayed.
R
The handset is too far from the base unit. Move closer.
R T

he base unit’s AC adaptor is not properly connected.
Reconnect AC adaptor to the base unit.
R...