Panasonic Kx Tge210 Operating Instructions Manual

							Troubleshooting
I f you still have difficulties after following the instructions in this section, disconnect the base unit’s
AC adaptor, then reconnect the base unit’s AC adaptor. Remove the batteries from the handset,
and then insert the batteries into the handset again. General use
Problem Cause/solution
The handset does not turn on
e
 ven after installing charged
batteries. R
Place the handset on the base unit or charger to turn on
the handset.
The unit does not work. RM
ake sure the batteries are installed correctly (page 10).
RFully charge the batteries (page 11).
R Check the connections (page 10).
R Unplug the base unit’s AC adaptor to reset the unit.
Reconnect the adaptor and try again.
R The handset has not been registered to the base unit.
Register the handset (page 35).
I cannot hear a dial tone. RT
he base unit’s AC adaptor or telephone line cord is not
connected. Check the connections.
R Disconnect the base unit from the telephone line and
connect the line to a known working telephone. If the
working telephone operates properly, contact our service
personnel to have the unit repaired. If the working
telephone does not operate properly, contact your service
provider/telephone company.
I cannot use the Smart function
k
 ey even if the   indicator is
f
lashing slowly. R
Another unit is in use. Wait and try again later.
The base unit beeps. RN
ew messages have been recorded. Listen to the new
messages (page 40). Menu list
Problem Cause/solution
The display is in a language I
c
 annot read. R
Change the display language (page 14).
I cannot register a handset to a
b
 ase unit. R
The maximum number of handsets (6) is already
registered to the base unit. Cancel unused handset
registrations from the base unit (page 35). For assistance, please visit http://www.panasonic.com/help
51Useful Information
TGE21x23x24x(en)_1122_ver031.pdf51   512013/11/22   14:22:30  
						

							Battery recharge
Problem Cause/solution
The handset beeps and/or  flashes.
R
Battery charge is low. Fully charge the batteries (page 11).
I fully charged the batteries, but
–  still flashes,
–  is displayed, or
–

the operating time seems to be shorter. R
C
lean the battery ends ( ,  ) and the charge contacts
w
ith a dry cloth and charge again.
R It is time to replace the batteries (page 10). Making/answering calls, intercom
Problem Cause/solution
 is displayed.
R
T
he handset is too far from the base unit. Move closer.
RThe base unit’s AC adaptor is not properly connected.
Reconnect AC adaptor to the base unit.
R The handset is not registered to the base unit. Register it
(page 35).
Noise is heard, sound cuts in
a
 nd out. R
You are using the handset or base unit in an area with
high electrical interference. Re-position the base unit and
use the handset away from sources of interference.
R Move closer to the base unit.
R If you use a DSL/ADSL service, we recommend
connecting a DSL/ADSL filter between the base unit and
the telephone line jack. Contact your DSL/ADSL provider
for details.
The handset does not ring. RT
he ringer volume is turned off. Adjust the ringer volume
(page 18, 29).
R Silent mode is turned on. Turn it off (page 33).
The base unit does not ring. RT
he ringer volume is turned off. Adjust the ringer volume
(page 18).
R Silent mode is turned on. Turn it off (page 33).
I cannot make a call. RT
he dialing mode may be set incorrectly. Change the
setting (page 16).
I cannot make or answer a call. RA
n outside line is being used after a cell locator feature is
used.
– KX-TGE230 series: To end the call, press  MLOCATES
CELL N on the base unit.
– KX-TGE240 series: To end the call if someone answers using the cellular phone, press  MZ N on the
base unit.
I cannot make long distance
c
 alls. R
Make sure that you have long distance service. 52
For assistance, please visit http://www.panasonic.com/helpUseful Information
TGE21x23x24x(en)_1122_ver031.pdf52   522013/11/22   14:22:30       
						

							Caller ID/Talking Caller ID
Problem Cause/solution
Caller information is not
d isplayed. R
You must subscribe to Caller ID service. Contact your
service provider/telephone company for details.
R If your unit is connected to any additional telephone
equipment such as a Caller ID box or cordless telephone
line jack, plug the unit directly into the wall jack.
R If you use a DSL/ADSL service, we recommend
connecting a DSL/ADSL filter between the base unit and
the telephone line jack. Contact your DSL/ADSL provider
for details.
R The name display service may not be available in some
areas. Contact your service provider/telephone company
for details.
R Other telephone equipment may be interfering with this
unit. Disconnect the other equipment and try again.
Caller information is displayed
o
 r announced late. R
Depending on your service provider/telephone company,
the unit may display or announce the caller’s information
at the 2nd ring or later.
R Move closer to the base unit.
Caller information is not
a
 nnounced. R
The handset or base unit’s ringer volume is turned off.
Adjust it (page 18, 29).
R The Talking Caller ID feature is turned off. Turn it on
(page 29).
R The number of rings for the answering system is set to  “2
rings ” or  “Toll saver ”. Select a different setting
(page 44).
R If the base unit and another handset are having an
intercom call, your handset does not announce caller
information.
The caller list/incoming phone
n
 umbers are not edited
automatically. R
The Caller ID number auto edit feature is turned off. Turn
it on and try again (page 31).
R You need to call back the edited number to activate Caller
ID number auto edit.
I cannot dial the phone number
e
 dited in the caller list. R
The phone number you dialed might have been edited
incorrectly (for example, the long distance “1” or the area
code is missing). Edit the phone number with another
pattern (page 38).
Time on the unit has shifted. RI
ncorrect time information from incoming Caller ID
changes the time. Set the time adjustment to  “Manual ”
(off) (page 29). For assistance, please visit http://www.panasonic.com/help
53Useful Information
TGE21x23x24x(en)_1122_ver031.pdf53   532013/11/22   14:22:30 
						

							Problem Cause/solution
The 2nd caller’s information is
n ot displayed during an outside
call. R
In order to use Caller ID, call waiting, or Call Waiting
Caller ID (CWID), you must first contact your service
provider/telephone company and subscribe to the desired
service.
After subscribing, you may need to contact your service
provider/telephone company again to activate this specific
service, even if you already subscribed to both Caller ID
and Call Waiting with Caller ID services (CWID). Answering system
Problem Cause/solution
The unit does not record new
m
 essages. R
The answering system is turned off. Turn it on (page 39).
RThe message memory is full. Erase unnecessary
messages (page 40).
R The recording time is set to  “Greeting only ”. Change
the setting (page 44).
R Your service provider/telephone company’s voice mail
service may be answering your calls before the unit’s
answering system can answer your calls. Change the
unit’s number of rings setting (page 44) to a lower value,
or contact your service provider/telephone company.
I cannot operate the answering
s
 ystem remotely. R
The remote access code is not set. Set the remote
access code (page 43).
R You are entering the wrong remote access code. If you
have forgotten your remote access code, enter the
remote access code setting to check your current code
(page 43).
R The answering system is turned off. Turn it on (page 43).
The unit does not emit the
s
 pecified number of rings. R
If the first ring is turned off, the number of rings decreases
by 1 from the specified number of rings. Voice mail
Problem Cause/solution
“ V
oice mail msg. via
phone co. ” is shown on the
handset display. How do I
remove this message from the
display? R
This notification is displayed when your service provider/
telephone company’s voice mail service (not the unit’s
answering system) has recorded a message for you.
Typically you can remove this notification from the display
by listening to the message. To listen to the message, dial
the voice mail number provided by your service provider/
telephone company (for most cases, this will be your own
phone number), and follow the voice instructions.
Depending on your service provider/telephone company,
you may need to remove all messages from your voice
mailbox to remove the notification. You can also remove
this notification by pressing and holding  # until the unit
beeps. 54
For assistance, please visit http://www.panasonic.com/helpUseful Information
TGE21x23x24x(en)_1122_ver031.pdf54   542013/11/22   14:22:30 
						

							Liquid damage
Problem Cause/solution
Liquid or other form of moisture
h as entered the handset/base
unit. R
Disconnect the AC adaptor and telephone line cord from
the base unit. Remove the batteries from the handset and
leave to dry for at least 3 days. After the handset/base
unit are completely dry, reconnect the AC adaptor and
telephone line cord. Insert the batteries and charge fully
before use. If the unit does not work properly, contact an
authorized service center. Caution:
R
T

o avoid permanent damage, do not use a microwave oven to speed up the drying process.
For assistance, please visit http://www.panasonic.com/help 55Useful Information
TGE21x23x24x(en)_1122_ver031.pdf55   552013/11/22   14:22:30 
						

							FCC and other information
56
For assistance, please visit http://www.panasonic.com/helpUseful InformationTGE21x23x24x(en)_1122_ver031.pdf56   562013/11/22   14:22:30This equipment complies with Part 68 of the 
FCC rules and the requirements adopted by 
the ACTA. On the bottom of this equipment 
is a label that contains, among other 
information, a product identifier in the 
format US:ACJ----------.
If requested, this number must be provided 
to the telephone company.
L Registration No.............(found on the 
bottom of the unit)
L Ringer Equivalence No. (REN).......0.1B
A plug and jack used to connect this 
equipment to the premises wiring and 
telephone network must comply with the 
applicable FCC Part 68 rules and 
requirements adopted by the ACTA. A 
compliant telephone cord and modular plug 
is provided with the product. It is designed 
to be connected to a compatible modular 
jack that is also compliant.
The REN is used to determine the number 
of devices that may be connected to a 
telephone line. Excessive RENs on a 
telephone line may result in the devices not 
ringing in response to an incoming call. In 
most but not all areas, the sum of RENs 
should not exceed five (5.0). To be certain 
of the number of devices that may be 
connected to a line, as determined by the 
total RENs, contact the local telephone 
company. For products approved after July 
23, 2001, the REN for the product is part of 
the product identifier that has the format 
US:AAAEQ##TXXXX. The digits 
represented by ## are the REN without a 
decimal point (e.g., 03 is a REN of 0.3).
If this equipment causes harm to the 
telephone network, the telephone company 
will notify you in advance that temporary 
discontinuance of service may be required. 
But if advance notice isnt practical, the 
telephone company will notify the customer 
as soon as possible. Also, you will beadvised of your right to file a complaint with 
the FCC if you believe it is necessary.
The telephone company may make changes 
in its facilities, equipment, operations or 
procedures that could affect the operation of 
the equipment. If this happens the 
telephone company will provide advance 
notice in order for you to make necessary 
modifications to maintain uninterrupted 
service.
If trouble is experienced with this 
equipment, for repair or warranty 
information, please contact a Factory 
Service Center or other Authorized Servicer. 
If the equipment is causing harm to the 
telephone network, the telephone company 
may request that you disconnect the 
equipment until the problem is resolved.
Connection to party line service is subject to 
state tariffs. Contact the state public utility 
commission, public service commission or 
corporation commission for information.
If your home has specially wired alarm 
equipment connected to the telephone line, 
ensure the installation of this equipment 
does not disable your alarm equipment. If 
you have questions about what will disable 
alarm equipment, consult your telephone 
company or a qualified installer.
This equipment is hearing aid compatible as 
defined by the FCC in 47 CFR Section 
68.316.
When you hold the phone to your ear, noise 
might be heard in your Hearing Aid. Some 
Hearing Aids are not adequately shielded 
from external RF (radio frequency) energy. If  
noise occurs, use an optional headset 
accessory or the speakerphone option (if 
applicable) when using this phone. Consult 
with your audiologist or Hearing Aid  
						

							For assistance, please visit http://www.panasonic.com/help
57Useful InformationTGE21x23x24x(en)_1122_ver031.pdf57   572013/11/22   14:22:30manufacturer about the availability of 
Hearing Aids which provide adequate 
shielding to RF energy commonly emitted 
by digital devices.
WHEN PROGRAMMING EMERGENCY
NUMBERS AND(OR) MAKING TEST
CALLS TO EMERGENCY NUMBERS:
1) Remain on the line and briefly explain to 
the dispatcher the reason for the call.
2) Perform such activities in the off-peak
hours, such as early morning or late 
evenings.
This device complies with Part 15 of the 
FCC Rules. Operation is subject to the 
following two conditions:
(1) This device may not cause harmful 
interference, and (2) this device must 
accept any interference received, including 
interference that may cause undesired 
operation.
Privacy of communications may not be 
ensured when using this phone.
CAUTION:
Any changes or modifications not expressly 
approved by the party responsible for 
compliance could void the user’s authority 
to operate this device.
NOTE:
This equipment has been tested and found 
to comply with the limits for a Class B digital 
device, pursuant to Part 15 of the FCC 
Rules. These limits are designed to provide 
reasonable protection against harmful 
interference in a residential installation. This
equipment generates, uses, and can radiate 
radio frequency energy and, if not installed 
and used in accordance with the 
instructions, may cause harmful 
interference to radio communications. 
However, there is no guarantee that 
interference will not occur in a particular 
installation. If this equipment does cause 
harmful interference to radio or television 
reception, which can be determined by
turning the equipment off and on, the user isencouraged to try to correct the interference 
by one or more of the following measures:
– Reorient or relocate the receiving 
antenna.
– Increase the separation between the 
equipment and receiver.
– Connect the equipment into an outlet on a 
circuit different from that to which the 
receiver is connected.
– Consult the dealer or an experienced 
radio/TV technician for help.
Some cordless telephones operate at 
frequencies that may cause interference to 
nearby TVs and VCRs. To minimize or 
prevent such interference, the base of the 
cordless telephone should not be placed 
near or on top of a TV or VCR. If  
interference is experienced, move the 
cordless telephone further away from the TV 
or VCR. This will often reduce or eliminate 
interference.
FCC RF Exposure Warning:
L This product complies with FCC radiation 
exposure limits set forth for an 
uncontrolled environment. 
L To comply with FCC RF exposure 
requirements, the base unit must be 
installed and operated 20 cm (8 inches) 
or more between the product and all 
person’s body. 
L This product may not be collocated or 
operated in conjunction with any other 
antenna or transmitter.
L The handset may be carried and operated 
with only the specific provided belt-clip. 
Other non-tested belt-clips or similar 
body-worn accessories may not comply 
and must be avoided.
Notice:
L FCC ID can be found inside the battery 
    compartment or on the bottom of the 
units.  
						

							58
For assistance, please visit http://www.panasonic.com/helpUseful InformationTGE21x23x24x(en)_1122_ver031.pdf58   582013/11/22   14:22:30Compliance with TIA-1083 standard: 
Telephone handsets identified with this logo 
have reduced noise and interference when 
used with T-Coil equipped hearing aids and 
cochlear implants.
T
Compatible with
Hearing Aid T-Coil
TIA-1083  
						

							Guía Rápida Española
Para obtener ayuda, visite http://www.panasonic.com/help (solo en inglés)
59Guía Rápida Española TGE21x23x24x(en)_1122_ver031.pdf59   592013/11/22   14:22:30Conexiones
Unidad base
1 Conecte el adaptador de corriente alterna a la unidad presionándolo firmemente.2 Enganche el cable para fijarlo.3 Conecte el adaptador de corriente alterna a la toma de corriente.4 Conecte el cable de la línea telefónica a la unidad, y después a la toma telefónica de una sola línea 
(RJ11C) hasta que escuche un clic.
5 Se requiere un filtro DSL/ADSL (no incluido) si tiene este tipo de servicio.Nota:LUse solo el adaptador de corriente alterna Panasonic PNLV226 que se suministra.
Cargador
1 Conecte el adaptador de corriente alterna a la toma 
de corriente.
1
4
5
3
4
2
1  
						

							60
Para obtener ayuda, visite http://www.panasonic.com/help (solo en inglés) Guía Rápida EspañolaTGE21x23x24x(en)_1122_ver031.pdf60   602013/11/22   14:22:30Instalación y carga de la batería
Cargue aproximadamente durante 7 horas.
Nota:LUTILICE SOLO baterías recargables de Ni-MH tamaño AAA (R03) ( ).LNO utilice baterías Alcalinas, de Manganeso o de Ni-Cd.LConfirme que las polaridades estén correctas (S, T).LCambie el idioma de la pantalla.LConfirme que aparezca “Cargando”      
Sugerencias de operación
Teclas de funciónAl oprimir una tecla de función, puede seleccionar 
la función que aparece directamente encima de 
ella en la pantalla. Preste atención a la pantalla 
para ver qué funciones están asignadas a las 
teclas de función durante la operación.KX-TGE210/KX-TGE230 KX-TGE240
Tecla navegadora
v (Volumen: {^} o {V}): Ajuste el volumen del 
receptor o el altavoz mientras habla.
{} REDIAL (Remarcación): Vea la lista de 
remarcación.
{V} CID (identificador de llamadas): Vea la lista 
de personas que llamaron.
Cambio de idiomas (Auricular) (predeterminado: “English”)
Cuando instale las baterías por primera vez, es posible que aparezca “Date and time Press SELECT”. 
Oprima {OFF} para salir.
Idioma de la pantalla{MENU}(11) s {r}: “Español” s {GUARDA} s {OFF} 
Idioma de la guía de vozDisponible para: series KX-TGE230/KX-TGE240{MENU}(112 s {r}: “Español” s {GUARDA} s {OFF}
1
2 ().
1
2
{V} {^}
{}




{^}, {V}, {}: Navegue por diversas  
listas y elementos.