Panasonic Kx Tge463 Quick Guide

PNQW4850ZA    TT1115KT0 Printed in Malaysia
Connections
1 Connect the AC adaptor to the power outlet.
Base unit
1 Connect the AC adaptor to the unit by pressing the plug firmly.2 Fasten the cord by hooking it.3 Connect the AC adaptor to the power outlet.4 Connect the telephone line cord to the unit, then to the single-line telephone jack (RJ11C) until you hear a click.5 A DSL/ADSL filter (not supplied) is required if you have a DSL/ADSL service.Note:LUse only the supplied Panasonic AC adaptor PNLV226.
1...

– 2 –
Battery installation/Battery charging
Charge for about 7 hours.
Note:
LUSE ONLY rechargeable Ni-MH batteries AAA (R03) size
 ().LDo NOT use alkaline/manganese/Ni-Cd batteries.
LConfirm correct polarities (S, T).
LFollow the directions on the display to set up the unit.
LConfirm “Charging” is displayed 
().
Operating tips
Soft keys
By pressing a soft key, you can select the feature shown 
directly above it on the display. Pay attention to the 
display to see what functions the soft keys are assigned...

– 3 –
Recording your greeting message of the answering system for 
the landline (Handset)
You can record your own greeting message instead of using a pre-recorded greeting message.1{MENU}(3)2 s {r}: “Yes” s {SELECT}2After a beep sounds, hold the handset about 20 cm (8 inches) away and speak clearly into 
the microphone (2 minutes max.).
3Press {STOP} to stop recording. s {OFF}
Link to cell
You can connect your base unit and cellular phone using Bluetooth® wireless technology, so that 
you can make or...

– 4 –
Pairing a Bluetooth cellular phone
1Base unit:
Press and hold {CELL 1} or {CELL 2} for about 5 seconds.
LAfter the corresponding CELL indicator on the base unit starts flashing, the rest of the 
procedure must be completed within 5 minutes.
2Your cellular phone:
While the corresponding CELL indicator is flashing, follow the instructions of your cellular 
phone to enter the pairing mode.
LDepending on your cellular phone, it may ask you to enter the Bluetooth PIN (default: 
“0000”).
LIf your...

– 5 –
Connecting/disconnecting the cellular phone (Handset)
Auto connection to the Bluetooth devices (cellular phones)
The unit connects to the Bluetooth devices at regular intervals if the connection is lost. To change 
the interval (default: “1 min”), see the operating instructions.
LWhen 3 Bluetooth devices (2 cellular phones and 1 headset) are paired to the base unit, only 
2 Bluetooth devices can be used with the unit at the same time, and the base unit loses its 
connection from other Bluetooth...

– 6 –
Basic operations
Making/Answering calls (Handset)
Making cellular calls1Dial the phone number. s {CELL}
LWhen the cellular line only mode is set, you can also press 
{C}/{s} instead of {CELL}.
LWhen only 1 cellular phone is paired, the unit starts dialing.
2When 2 cellular phones are paired:
{r}: Select the desired cellular phone. s {SELECT}
Making landline callsDial the phone number. s {C}/{s}
Answering calls{C}/{s}
To hang up{OFF}
To adjust the receiver/
speaker volumePress {+} or {-} repeatedly...

– 7 –
Phonebook (Handset)
Adding entries1{

– 8 –
Using Bluetooth devices
Copying phonebook entries from a Bluetooth cellular phone (phonebook transfer)
You can copy phonebook entries from the paired cellular phones or other cellular phones (not 
paired) to the unit’s phonebook.
1Handset: {MENU}(6182Handset:
To copy from paired cellular phones: 
{r}: Select the desired cellular phone. s {SELECT}
LCopied items are stored to the group (“Cell 1” or “Cell 2”) which the cellular phone is 
paired to. 
To copy from other cellular phones (not paired):...

– 9 –
Using a Bluetooth wireless headset (optional) for landline calls
By pairing a Bluetooth headset to the base unit, you can have a hands-free conversation wirelessly 
for landline calls.
LOnly 2 Bluetooth devices can be used with the unit at the same time (for example, 2 cellular 
lines, or the headset and 1 cellular line).
Pairing a headset to the base unit1Your headset:
Set your headset to pairing mode.
LRefer to your headset operating instructions.
2Handset:
{MENU}(621
1 Pair using the handset.2...

– 10 –
Frequently asked questions
QuestionCause/solution
Why is _ displayed?LThe handset is too far from the base unit. Move closer.
LThe base unit’s AC adaptor is not properly connected. Reconnect 
AC adaptor to the base unit.
LThe handset is not registered to the base unit. Register it.
1Handset: {MENU}(13)2Base unit: Press and hold {LOCATOR} or {HANDSET 
LOCATOR} for about 5 seconds.
3Handset: Press {OK}, then wait until a long beep sounds. 
Why am I unable to pair a 
cellular phone to the base...