Panasonic Lcd Tv Dvd Video Receiver Cq Vd7200u Operating Instructions

							24251E
N
G
L
I
S
H
1E
N
G
L
I
S
H
CQ-VD7200U
CQ-VD7200U
16E
N
G
L
I
S
H
Indicates the compatible types of disc.
DVD
VIDEO
VIDEO
CD
Note: It is possible to press []] [[] on the display unit instead of [s] [d] on the remote control
. ( [[] 
on the display
unit cannot be used in place of 
[d]
that is used for slow playback.)
Basic Operation
Go to Beginning
Fast Forward/
Fast Reverse
[d]: next track (chapter)
[s]: beginning of the current track (chapter)
Previous track (chapter) (Press twice.)
Note: When playing a DVD video, there are cases where it is not 
possible to return to the start of a chapter that spans 2 titles.
(apage 94)
Press and hold
[d]: fast forward
[s]: fast reverse
Release to resume playback.
The speed changes if the button is held down as follows.
Regular speed/1.5 times /10 times/20 times
Stop
Press[3] (STOP).
Press [5](PLAY)again, and play will resume from the point where [3]
(STOP) is pressed. (Continued playback function)
To cancel continued playback, press[3] (STOP)again in the stop
mode.
Pause
Press[y] (PAUSE).
To resume playback, [5](PLAY)or [y](PAUSE)again.
Slow 
Playback
Press and hold[d]in the pause mode.
Playback is at about 1/3 normal speed.
To resume normal playback, press [5](PLAY).
To pause, press [y](PAUSE)again.
Note: Reverse slow playback is not possible.
Repeat
Play
Press[REP] (REPEAT).
Press [REP] (REPEAT) again to cancel.
Perform these operations (
a
page 25-27) with the remote control. 
Operations vary according to the disc. For details, refer to the guide provided with the disc.
DVD
VIDEO
VIDEO
CD
DVD
VIDEO
VIDEO
CD
DVD
VIDEO
VIDEO
CD
DVD
VIDEO
VIDEO
CD
DVD
VIDEO
VIDEO
CD
DVD
VIDEO
VIDEO
CD
15E
N
G
L
I
S
H
DVD/Video CD Player
POWER
VOLUM
E
M
EN
U M
UTE
M
O
DENA
VI
NAVIGATION
ENTER
TILTASPECTC
Q
-V
D
7
2
0
0
U
IN-DASH 7 INCH WIDE COLOR LCD TV / DVD - VIDEO / RECEIVER
DISC
P.
MODEAS
P
Notes: 
¡Do not insert a disc when disc indicator or
eject button lights because a disc is already
loaded.
¡The power will be turned on automatically when a
disc is loaded.
¡You can play a disc even if the monitor is closed.
¡The sound may be interrupted for a few moments
while the audio format is being identified.Note: If you leave a disc in the slot for more than 30
seconds after its ejection, the disc will be automatically
reloaded after loud beep is energized three times.Disc Insert¡The mode that supports the disc is selected, and
playback starts. 
¡The audio format is automatically identified. 
(apage 32)
¡When the menu screen appears, see “DVD Menu/
Video CD Menu” on page 26.Disc EjectPress [u]to stop playback and eject the disc.
(Press [u]again to reload the disc.) When DVD or Video CD is in the player, press
[MODE]to change to  DVD or Video CD player
mode and playback starts.
[3] (STOP)[y](PAUSE)
[5](PLAY)
[s][d]
(apage 25)[REP] (REPEAT)
Notes: 
¡Due to limitations of certain discs, some DVD video
and Video CD discs may not operate as described in
these Operating Instructions. Refer to the disc jack-
et for further details.
¡This unit does not support DVD and Video CD
karaoke functions. [MODE] 
Label side[u] (Eject)
(Lights when
a disc is in
the deck)Cautions: 
¡Do not use irregularly shaped discs. 
¡Do not insert foreign matter into the disc slot.
[MODE]
[]] [[]
(apage 25)
Video CD mode display
Play setting Sound setting 
(Stereo/monaural)
Playing time Mode display
DVD mode display
Play settingAudio format 
(apage 32)
Playing time
Title numberChapter number
Mode displayDisc indicator
Subtitle language/audio language/angle
Disc indicator 
						

							271E
N
G
L
I
S
H
CQ-VD7200U
18E
N
G
L
I
S
H
Indicates the compatible types of disc.
DVD
VIDEO
VIDEO
CD
Switching between
Stereo and
Monaural
VIDEO
CD
Press [AUDIO] (ST/MONO).
It is possible to switch the audio between stereo sound and monaural
sound (L or R).
Notes: 
¡If no operation is performed for 5 sec-
onds, the display returns to the regular
mode.
¡It may not be possible to switch the lan-
guage unless the unit is at the DVD menu
(apage 26) or is at the DVD settings.
(apage 46)
¡The language on the DVD settings has a
priority over when the power is turned on
or the disc is loaded. (apage 46)
¡The number of languages depends on the
disc. Some discs have only one language
or have no language. : the left channel audio is output on both the left and
right speakers.
: the right channel audio is output on both the left
and right speakers. : stereo sound
STEREOMONO RchMONO Lch
Useful Function
Switching the
Subtitle 
LanguageSwitching the
Audio 
LanguageSwitching the
Angle
Press[SUB](SUB TITLE) during playback.
It is possible to change the subtitle language during play if the multiple
languages are recorded on the disc.
Note: There may be a brief delay before the subtitles appear.
Press[AUDIO]during playback.
It is possible to change the audio language during play if multiple audio
languages are recorded on the disc.
Press[ANGLE]during playback.
For DVDs which contain scenes which have been shot simultaneously
from a number of different angles the same scene can be viewed from
each of these different angles during play.
DVD
VIDEODVD
VIDEODVD
VIDEO
[ANGLE] 
[AUDIO]
(ST/MONO)[0] to [9]
(Title/chapter
Number)
(apage 26) [DVD]
(DVD MENU)
(apage 26)
[RET](RETURN)
(apage 26)[TITLE]
(TITLE/CHAPTER)
(apage 26)
[]] [[] [}] [{]
(Select)
[ENTER]
(apage 26) [SUB]
(SUB TITLE)
261E
N
G
L
I
S
H
CQ-VD7200U
17E
N
G
L
I
S
H
DVD/Video CD Player
(continued)
Chapter/Title Selection
To return the previous display, press [RET](RETURN).
Starting Playback
from a Specific
Title/ChapterTitle MenuIf the DVD has multiple titles
recorded on it, it is possible
to select the preferred title
from the title menu to start
playback.
DVD
VIDEODVD
VIDEO
DVD Menu/
Video CD MenuUse this menu during 
playback to select content,
audio, subtitle, etc., from a
menu (the DVD/Video CD
menu) that is unique to each
disc.
DVD
VIDEO
VIDEO
CD
TITLE MENU
RiversLovers
CastlesWoods
Regular Mode
Title Number Input ModeChapter Number Input Mode
q
Press [DVD] (DVD MENU)during
DVD playback.
(For the Video CD menu, press [RET]
(RETURN) during playback.)
w
Press []], [[], [}] or[{] to
select the preferred menu.
For the DVD/Video CD with playback
control (apage 94), press [0]to [9]
on the remote control.
e
Press [ENTER].
To return the previous display, press
[RET](RETURN).
q
Press [TITLE] (TITLE/CHAPTER)
to select the input mode. The mode
changes as shown at right every
time [TITLE] (TITLE/CHAPTER)is
pressed.
w
Press [0]to [9]to input preferred
title/chapter number.
To input the number again, press
[RET] (RETURN).
e
Press [TITLE] (TITLE/CHAPTER).
Playback will start automatically.
q
Press and hold [DVD](DVD MENU)for
more than 2 seconds during playback.
w
Press []], [[], [}] or[{] to 
select the preferred title.
For the DVD with playback control
(apage 94), press [0]to [9]
on the remote control.
e
Press [ENTER].
Example: 
Example: 
“5” lights on pink.
Notes: 
¡For the VCD mode, do not press [TITLE] (TITLE/CHAPTER)but press
the numerical key to enter a number directly.
¡If no operation is performed for 8 seconds after [TITLE] (TITLE/
CHAPTER) has been pressed, the display returns to the regular mode.
¡If the title/chapter number is pressed and no operation is performed for
2 seconds, the playback will start from the number of the title/chapter
entered. 
MENU DVD
1. SUBTITLE
2. AUDIO
3. ANGLESelect your favorite music.1. Love Supremes
2. Impressions
3. In a Sentimental Mood 
Number:  
						

							28291E
N
G
L
I
S
H
1E
N
G
L
I
S
H
CQ-VD7200U
CQ-VD7200U
20E
N
G
L
I
S
H
Indicates the compatible types of disc.
CD
MP3
19E
N
G
L
I
S
H
CD/MP3 Player
Disc InsertThe mode that supports the disc is selected, and play-
back starts.
When a disc is in the player, press [MODE]to
change to CD or MP3 player mode and playback
starts.
Notes: 
¡Do not insert a disc when disc indicator or
eject button lights because a disc is already
loaded.
¡The power will be turned on automatically when a
disc is loaded.
¡You can play a disc even if the monitor is closed.Disc EjectPress [u]to stop playback and eject the disc.
(Press [u]again to reload the disc.)
POWER
VOLUM
E
M
EN
U M
U
TE
M
OD
EN
AVI
NAVIGATION
ENTER
TILTASPECTC
Q
-V
D
7
2
0
0
U
IN-DASH 7 INCH WIDE COLOR LCD TV / DVD - VIDEO / RECEIVER
DISC
P.
MODEASP
[MODE] []] [[]
(Track/file)
[}] [{]
(Folder)
[ENTER]
[]][[]
(Track/file)
[}] [{] (Folder)
[ENTER]
[4] (RANDOM)
[SCRL](SCROLL)
[REP](REPEAT) Label side
Cautions: 
¡Do not use irregularly shaped discs. 
¡Do not insert foreign matter into the disc slots.
Track number Play time Mode display
CD/MP3 mode display
[u] (Eject)
(Lights when
a disc is in
the deck)
[MODE]Disc indicator
Total track
Disc title
Track title
Play setting
Note: If you leave a disc in the slot for more than 30
seconds after its ejection, the disc will be automatically
reloaded after loud beep is energized three times.Direct Folder Selectionq 
Press [ENTER]during playback.
w 
Press []],[[], [}] or[{] to select a folder.
[]][[] : movement among different levels of trees
[}] [{]:movement in the same tree
e 
Press [ENTER].
Note: It is not possible to display the whole trees and
a file list in a folder.
For 
“Folder selection order/MP3 file playback
order”. 
(apage 31)
: MP3 files are included
: No MP3 files
MP3
[3] (STOP)[y](PAUSE)
[5](PLAY)
[s][d]
(apage 29)
Basic Operation
Repeat Play
Press [REP] (REPEAT).
Press [REP] (REPEAT)again to cancel.
Press [REP] (REPEAT).
Press [REP] (REPEAT)again to cancel. Current 
File
Press and hold [REP] (REPEAT) for more than 2 seconds.
Press and hold [REP] (REPEAT)again to cancel. Current 
Folder
CDMP3
Random
Play
Press [4] (RANDOM).
Press [4] (RANDOM)again to cancel.
Press [4] (RANDOM).
Press [4] (RANDOM)again to cancel. All
Files
Press and hold [4] (RANDOM)for more than 2 seconds.
Press and hold [4] (RANDOM)again to cancel. All Files in the
Current Folder
CDMP3
Go to Beginning
Fast Forward/
Fast Reverse
[d]: next track/file 
[s]: beginning of the current track/file
Previous track/file (Press twice.)
Press and hold. 
[d]: fast forward
[s]: fast reverse
Release to resume playback.
Stop
Press[3] (STOP).
Pause
Press[y] (PAUSE).
To resume playback, [5](PLAY)or [y](PAUSE)again.
CD
MP3CD
Sequential Transition
From One File 
to the Next
Press and hold. 
[[]: forward
[]]: backward
MP3
CD
MP3
Title 
Scroll
Press [SCRL] (SCROLL).
CD
MP3
Folder 
Selection
[}
]: next folder
[
{
]: previous folderWhen the file list is displayed: 
[
}
]: previous folder
[
{
]: next folder
MP3
CD
MP3
Note: It is possible to press []] [[] on the display unit instead of [s] [d] on the remote control
. 
Perform these operations with the remote control.  
						

							30311E
N
G
L
I
S
H
1E
N
G
L
I
S
H
CQ-VD7200U
CQ-VD7200U
22E
N
G
L
I
S
H
21E
N
G
L
I
S
H
CD/MP3 Player
(continued)
This player allows you to play MP3 files recorded on CD-ROMs, CD-Rs
(Recordable) and CD-RWs (Rewritable).¡It is recommended that you set the bit rate to “128 kbps or more” and “Fixed”.
¡Bit rate 8 kbps of MPEG-2 and sampling frequency 16 kHz of MPEG-2 can not be reproduced.
¡VBR (Variable Bit Rate) is not supported.
¡The playback sound quality differs depending on the encoding software and the bit rate.  For details refer to the user
manual of your encoding software.
■
Converting (encoding) audio data to an MP3 file¡Do not record files other than MP3s or unnecessary folders on a disc.If many folders or files other than MP3s
are recorded on a disc, it may take some time before playback starts.
¡Use ISO 9660 file system (Extension of the ISO 9660 file systems are included.) (apage 31). APPLE HFS file
system is not supported.  If they do not conform to ISO 9660 file system, the file may not play normally, or the file
or folder names may not be displayed correctly. 
¡Make sure to add the “.mp3” extension to each MP3 file name.A file with a different file name extension or none
at all will not play.
¡Although Multi session recording is supported, the use of Disc-at-Once is recommended.  Make sure to close the
session when you finished recording on a disc.
¡A disc recorded by the packet writing software are not supported.
¡A playlist function is not supported.  Record files and folders in the order in which you want them to be played.
Some writing software lets you specify the recording order by adding a prefix in the range of “01” - “99”, etc. to the
file name.  For details refer to the user manual of your writing software.
Notes: 
¡You may encounter trouble in playing MP3s or displaying the information of MP3 files recorded with certain writing
softwares or CD recorders (CD-R/RW drives).
¡If a disc contains both MP3 and CD-DA, only CD-DA data is reproduced properly. (MP3 files are played but no
sound is output).
■
Recording MP3 files on a CD-R/RW
What is MP3?MP3, short for MPEG-1 Audio Layer 3,  MPEG-2 Audio Layer 3 LSF (Low Sampling Frequency), is a standard for compress-
ing digital video data adopted for video CDs and similar media.  It is one of the audio compression systems covered by
MPEGs (Motion Picture Experts Group) digital audio compression standards.  What it does is reduce the number of bytes
in a song without detracting from the sound quality by eliminating big sound waves within the sound range that is imper-
ceptible to the human ear.  This compression allows you to reduce the contents of a conventional music CD by a factor of
around 10.  This means that you can record the contents of 10 music CDs on a single CD-R or CD-RW.  (The figures refer
to data recorded on a 650 MB CD-R or CD-RW at a fixed bit rate of 128 kbps and a sampling frequency of 44.1 kHz.)
Points to Remember When Recording an MP3 Disc
Warning: Never assign the “.mp3” file name extension to a file that is not in the MP3 format.  This may produce
noise from the speakers and cause speaker damage and can damage your hearing.
Folder selection order/MP3 file playback order (Example)
Notes: 
¡This unit counts the number of folders irrespective
of the presence or absence of MP3 file. 
¡If the selected folder does not contain any MP3
files, the nearest MP3 files in the order of playback
will be played.
¡Playback order may be different from other MP3
players even if the same disc is used.
¡“ROOT” appears when displaying the root folder’s
folder name.
Root Folder
(Root Directory)
Folder Selection
File Selection
Tree 1  Root Tree 2 Tree 32 13
45
q
we
r6
16
~
In the orderIn the orderqr
~
: []][[]
:  [}][{]
Tree 1  Root Tree 2
13
245
: MP3 files are included   : No MP3 files
Root Folder
Current Folder
Folder in the next
lower level of tree
Supported file systems and file names Maximum number of files/folders¡Maximum number of trees: 8
¡Maximum number of folders: 254 (Root folder is not included.)
¡Maximum number of files: 512 
Note: If the number of files and folders exceeds the number mentioned above, successful playback may not be performed.CopyrightIt is prohibited by copyright laws to copy, distribute and deliver copyrighted materials such as music without the approval
of copyright holder except for personal use.No warrantyAbove description complies with our investigations as of December 2003. It has no warranty for reproducibility and dis-
playability of MP3. Note: MP3 encode software and writing software are not supplied to this model.ISO 9660 Level 1/Level 2 
Joliet*
Romeo
Apple Extension to ISO 9660
Supported file system Displayable folder names and file names
Name files and folders in accordance with the standard of each file system.Refer to the instructions of writing software for details.
¡This player can display file names of up to 31 ASCII character set in scroll mode.
* Up to 15 letters can be displayed when scrolling in the Joliet system.
According to the standard, “á”, “ç”, etc. can be used. However, this unit can
not display those letters.
¡The unit recognizes only ASCII character set.  Chinese characters, accented
French characters and accented Spanish characters will be converted into an
asterisk. 
						

							32331E
N
G
L
I
S
H
1E
N
G
L
I
S
H
CQ-VD7200U
CQ-VD7200U
24E
N
G
L
I
S
H
[DRC] 
(Dynamic Range
Compression) 
Indicates the compatible types of disc.
DVD
VIDEO
VIDEO
CD
CD
Producing Audio
That Is Audible at
Low Volumes
(Dynamic Range
Compression)This function is effective for
playback of Dolby
Digital/Dolby Surround DVD
video.  The words of an
actor hardly audible during
playback at a low volume,
for example, will become
easier to listen to by select-
ing DR COMP MIN.Press [DRC]to change the setting.
: movie theater mode with
no compression.
: mode recommended by the software manu-
facturer for listening at low volume.
Conversation
level
: mode with the greatest compression, roughly
equivalent to a TV broadcast.
DR COMP OFFDR COMP MIN
OFF STD MIN DR COMP STD
23E
N
G
L
I
S
H
Audio Formats
DVD
VIDEO
❒LPCM (Linear PCM)In this format, the audio signal is converted to digital data and recorded in two
channels without compression. Because the capacity of a DVD video disc is
large, it can store more data with better accuracy than a CD.Note:
“LPCM” is displayed only for DVD video discs.
❒Dolby DigitalThis fully discrete format divides the music signals into 5.1 channels: Front
Left (L), Front Right (R), Center (C), Left Surround (LS), Right Surround (RS)
and Subwoofer (SW: 0.1 channel) for recording and playback. The number of
channels that are recorded depends on the software. (1 to 5.1 channels)❒Surround FormatThis format records signals from four channels [Front Left (L), Front Right
(R), Center (C), and Monaural Surround (S)] in two channels, decodes those
channels through a Dolby Pro Logic decoder, and then outputs the resulting
signals in four channels.❒dtsThis format requires more data than Dolby Digital, and provides higher quality
surround playback.
Similar to Dolby Digital, this fully discrete format divides the music signals
into 5.1 channels: Front Left (L), Front Right (R), Center (C), Left Surround
(LS), Right Surround (RS) and Subwoofer (SW: 0.1 channel) for recording
and playback.
DVD
VIDEO
VIDEO
CD
CD
DVD
VIDEODVD
VIDEO
PRO • LOGIC
CD
Notes: 
¡Only in cases where the Digital Audio Output (optical) of this product is connected, dts audio will be output. (apage 82)
¡To output 5.1-channel audio signals, other device must be connected. (apage 82)
¡DVD-recorded audio data, such as
,will be displayed on the screen. The audio to be actually reproduced
may differ from the display on the screen depending on the setting. 
						

							34351E
N
G
L
I
S
H
1E
N
G
L
I
S
H
CQ-VD7200U
CQ-VD7200U
26E
N
G
L
I
S
H
25E
N
G
L
I
S
H
Radio
One-touch Selection of a Station
Up to 6 stations each can be saved in the FM1, FM2, FM3 and AM preset station memories.Manual Preset
Memory
Select a band and frequency. (step wand eon the previous page)
Press and hold [1]to [6]on the remote control for more than 2 seconds.
The frequency blinks once, and
a receiving station is saved in
the memory.
Auto Preset
Memory
Select a band. (step won the previous page)
Press and hold [ENTER]for more than 2 seconds.
¡The 6 strongest available stations will be automatically saved in the
memory under preset numbers 1 
to6.
¡Once set, the preset stations are sequentially scanned for 5 seconds
each.
¡To stop the scanning, press [1]to [6]on the remote control.
Preset Station
Calling
Select a band. (step won the previous page)
Press [1] to[6]on the remote control.
Note: New stations overwrite existing saved stations after following this procedure.
VOLUME
MENU MUTEMODE NAVI
NAVIGATION ASPECT
P·
MODE
POWER
ASPENTER
CQ-VD7200U
IN-DASH 7 INCH WIDE COLOR LCD TV / DVD - VIDEO / RECEIVER
DISCTRACK/
CHANNEL
MODEENTER
Tuning[[]: up
[]]: down
Press and hold [[]or[]]for more than 0.5 sec-
onds, then release. Seeking will start and stops at next
available station.Radio ModePress [MODE]to change to radio mode.BandPress [ENTER]to change
the bands.
Note: The stereo indicator lights during reception of
an FM stereo broadcast.
123
[1] to [6]
(Preset memory) BandMode display
Stereo indicator
[MODE] Preset memory FrequencyBand list
[]] [[] (Tuning)
[ENTER] (Band)
[]] [[] 
(Tuning)
[ENTER] 
(Band) [MODE] 
FM1
FM2
FM3
AM 
						

							36371E
N
G
L
I
S
H
1E
N
G
L
I
S
H
CQ-VD7200U
CQ-VD7200U
28E
N
G
L
I
S
H
27E
N
G
L
I
S
H
CD Changer Control
Basic Operation
Random Play
Press and hold [4](RANDOM)for more than 2 seconds.
Press and hold [4](RANDOM)again to cancel.
All Tracks
Press [4](RANDOM).
Press [4](RANDOM)again to cancel.
All Tracks on
the Current Disc
Scan PlayThe first 10 seconds of each
track will be played.Press and hold [5](SCAN)for more than 2 seconds.
Press and hold [5](SCAN)again to cancel.
All Tracks
Press [5](SCAN).
Press [5](SCAN)again to cancel.
1st Track on
Each Disc
Repeat Play
Press and hold [6](CH REPEAT)for more than 2 seconds.
Press and hold [6](CH REPEAT)again to cancel.
Current Track
Press [6](CH REPEAT).
Press [6](CH REPEAT)again to cancel.
Current Disc
Perform these operations with the remote control. 
VOLUME
MENU MUTEMODE NAVI
NAVIGATION ASPECT
P·
MODE
POWER
ASPENTER
CQ-VD7200U
IN-DASH 7 INCH WIDE COLOR LCD TV / DVD - VIDEO / RECEIVER
DISCTRACK/
CHANNEL
MODEENTER
CD Changer ModePress [MODE]to change to CD changer mode and
playback starts.CD changer functions are designed for an optional
Panasonic CD changer unit.
Read the operating instructions for CD changer as well.
Preparation: Connect the CD changer (apage 78, 79),
and load a magazine (disc). 
Mode display
Track
number
Disc list Play time
Total time
Total track Disc 
number Play 
setting
[MODE][]][[](TRACK)
[}] [{](DISC)
Caution: Do not use irregularly shaped CDs. Notes: 
¡The power will be turned on automatically when a
magazine is loaded.
¡Load a magazine with CDs when “NO MAGAZINE” is
displayed.
¡CD text is not supported in CD changer mode.
¡CD changer cannot play MP3 data recoded CD-
R/RW discs.
Note: It is possible to press []] [[] on the display unit instead of [s] [d] on the remote control
.
Fast Forward/
Fast Reverse
Press and hold. 
[d]: fast forward
[s]: fast reverse
Release to resume playback.
Disc Selection
[}](DISC): next disc
[{](DISC): previous disc
Track Selection
[d](TRACK): next track
[s] (TRACK): 
beginning of the current track
Previous track (Press twice.)
[]][[](Track)
[}] [{](Disc) [MODE]
[4](RANDOM)
[5](SCAN)
[6](CH REPEAT)
(Changer repeat)
[1](CH 1)
[2](CH 2)
System ExpansionThe use of Dual CD Changer Selector CA-CD55
(option) allows you to make the following connec-
tions. (
a
Page 79)
Dual changers connectionTwo changers can be connected to the terminals of
CA-CD55 respectively.
The changers are arranged as follows.[1]: CH 1
[2]: CH 2 
						

							Notes: 
¡Press [MODE]to return to the regular mode.
¡The display returns to the previous one if there is no
operation for more than 60 seconds after changing to
the setting menu.
3
Navigation input
: connected to the RGB input cord, or a car navigation system
not connected
: connected to the VTR1-IN
: connected to the VTR2-IN
VTR2VTR1RGBNAVI INPUT[}] [{] 
[]][[]
(Select)
[ENTER]
[MODE]
(End)
[MENU] Setting
Navigation volume
: the sound that a car navigation system generates does not come out.
: volume level
5
4
3
2
10NAVI VOLUME
Navigation mute level
NAVI MUTE (dB)
: unchanged : decrease 20 dB
: decrease 10 dB : no sound
– ∞
–10
–20
0
Low High
qPress [}] or[{]to select
an item.
w
Press 
[[]
or []]
to select
the setting.
e
Press 
[ENTER]
to set.
Note: Make sure to select 
“RGB
”when no car navigation is connected.
VOLUME
MENU MUTEMODE NAVI
NAVIGATION ASPECT
P·
MODE
POWER
ASPENTER
CQ-VD7200U
IN-DASH 7 INCH WIDE COLOR LCD TV / DVD - VIDEO / RECEIVER
DISCTRACK/
CHANNEL
MENU MODEENTER
383929E
N
G
L
I
S
H
30E
N
G
L
I
S
H
CQ-VD7200U
CQ-VD7200U
Monitor PositionTILT (Tilting angle adjustment)
Default: 3
Setting range: 1 to 5
SLIDE (Front-rear position)
Default: Front
Setting range: Front, RearNavigation Set UpNAVI INPUT (Navigation input)
Selection of the terminal that connects to the
car navigation system allows you to switch to
images and sounds of the car navigation sys-
tem by pressing [NAVI] (NAVIGATION).
Default: RGB
NAVI VOLUME (Navigation volume)
Volume adjustment of the car navigation sys-
tem is executed.
Default: 4
NAVI MUTE (Navigation mute level)
Select the mute level of this unit during the
voice guidance from the Panasonic car naviga-
tion system (available in future). 
Preparation: Connect the navi mute lead.
Note: You can set the navigation mute level
when 
“RGB
”is selected on navigation input.
Default: –10 dB
1
2
Notes: 
¡For smooth adjustment, make sure to first return the lateral angle to the neutral position and then adjust the tilt angle.¡Front-rear position 
“REAR
”and tilt angle 
“5”cannot be selected at the same time.
¡The monitor position setting menu can also be displayed by pressing the [TILT]button on the display unit for more
than 1 second. (apage 19)Tilting angle adjustment
Press [{] or[}]to select the setting.
5
4
3
2
1
TILT
[}] [{] []] [[]
(Select)
[ENTER] [MENU] 
[{][}]
Front            Rear
[]][[]
SET-UP: User Settings
q
Press 
[}]
or [{]
to
select 
“TILT/SLIDE
”.
w
Press 
[ENTER]
to set.
TILT/SLIDE
q
Press 
[}]
or [{]
to
select 
“NAVI SETUP
”.
w
Press 
[ENTER]
to set.
NAVI SETUP
[MODE]
(End)
Menu
Submenu
Front-rear position
Press []] or[[]to select the setting.REAR
FRONTSLIDE
qPress [MENU]to
display the menu.
w
Press 
[[]
or []]
to
select “USER”. 
AUDIOCAPTURE
DATEDVDSCREENUSER 
						

							Notes: 
¡Press [MODE]to return to the regular mode.
¡The display returns to the previous one if there is no
operation for more than 60 seconds after changing to
the setting menu.
3
Setting
[}] [{] 
[]][[]
(Select/adjust)
[ENTER]
[MODE]
(End)
[MENU] [0]to [9]
VOLUME
MENU MUTEMODE NAVI
NAVIGATION ASPECT
P·
MODE
POWER
ASPENTER
CQ-VD7200U
IN-DASH 7 INCH WIDE COLOR LCD TV / DVD - VIDEO / RECEIVER
DISCTRACK/
CHANNEL
MENU MODEENTER
404131E
N
G
L
I
S
H
32E
N
G
L
I
S
H
CQ-VD7200U
CQ-VD7200U Rear view camera input
: unconnected
: connected to the VTR1-IN
: connected to the VTR2-IN
Note: Make sure to select “OFF” when no rear view camera is connected.
Rear view camera scale display
: scale display off
: scale display on
Scale adjustment
Press[[]
or []]
to adjust the width.
Press 
[}] or[{] 
to adjust the angle.
SCALE ADJUST
ONOFFSCALEVTR2VTR1OFF
CAMERA INPUTHow to set your ID code (for the first time)
q
Enter an 4 digit ID code.
w
Enter the same 
4 digit 
ID code again.
How to change your ID code 
q
Enter the preset (old) 
4 digit 
ID code.  If the wrong ID code is entered, a
new ID code cannot be registered.
w
Enter a new 
4 digit 
ID code.
e
Enter the new 
4 digit 
ID code again.
How to cancel the known ID code Note: Should your unit ever require service, cancel your ID code before send-
ing for repair.q
Enter the preset (old) 
4 digit 
ID code. If the wrong ID code is entered, it is
not possible to cancel the ID code function.
w
Press and hold 
[ENTER]
until 
“Complete!
” is displayed
. The ID code can-
celling procedure is completed. The unit now works without an ID code.
Note: 
Refer to ID Code Input regarding how to enter the ID code. (apage 11)
ID Code settingPrior to operating this unit, it is advisable to
assign your 4-digit ID code for security. 
(Make sure to use four digitsfor ID code.)
Once the ID code has been set, the unit cannot
be operated if the main power supply is dis-
connected then re-connected. It is electronical-
ly locked so that a thief could not use the
stolen unit unless that person knows the code
you have set.
The ID code operation must be performed only
by the person whom the unit belongs to.
Generally, it is not necessary to enter the ID
code each time when using the unit if it has
not been disconnected from the main power
supply (car battery).SET-UP: User Settings
(continued)
Rear View Camera Set upCAMERA INPUT (Rear view camera input)
Selection of the terminal that connects to the
rear view camera allows you to view images
through the rear view camera automatically
when you put the shift lever into the reverse
position.
Preparation: Connect the reverse lead. 
(apage 81)
Default: OFF
SCALE (Rear view camera scale display)
Images through the rear view camera can be
shown in the scale display mode.
Default: OFF
SCALE ADJUST (Scale adjustment)
Default: 0 (width/angle)
1
2
[}] [{] []] [[]
(Select/adjust)
[ENTER] [MENU] 
q
Press 
[}]
or [{]
to
select
“CAMERA SETUP
”.
w
Press 
[ENTER]
to set.
CAMERA SETUPq
Press 
[}]
or [{]
to
select 
“ID-CODE
”.
w
Press 
[ENTER]
to set.
ID-CODE
[MODE]
(End)
Menu
Submenu
Press [0]
to [9] on the remote
control to input the ID code.
qPress [}] or[{]to select
an item.
w
Press 
[[]
, []]
, [}] or
[{]
to select or adjust the
setting.
e
Press 
[ENTER]
to set.
Caution: Record your regis-
tered ID code and keep it in a
secure location. If you forget it,
you will be unable to use the
unit. In case you forget the ID
code, please consult your near-
est Panasonic Servicenter.
qPress [MENU]to
display the menu.
w
Press 
[[]
or []]
to
select “USER”. 
AUDIOCAPTURE
DATEDVDSCREENUSER 
						

							VOLUME
MENU MUTEMODE NAVI
NAVIGATION ASPECT
P·
MODE
POWER
ASPENTER
CQ-VD7200U
IN-DASH 7 INCH WIDE COLOR LCD TV / DVD - VIDEO / RECEIVER
DISCTRACK/
CHANNEL
MENU MODEENTER
Notes: 
¡Press [MODE]to return to the regular mode.
¡The display returns to the previous one if there is no
operation for more than 60 seconds after changing to
the setting menu.
3
Setting
qPress [}] or[{]to select
an item.
w
Press 
[[]
or []]
to select
the setting.
e
Press 
[ENTER]
to set.
Beep setting
: operation sound (Beep) OFF
: operation sound (Beep) ON
ONOFFBEEP
Video control setting
: connected to the VTR1-IN
: connected to the VTR2-IN
Notes: 
¡Select a terminal connected to the DVD output terminal of a Panasonic car
navigation system with a built-in DVD player (available in future) through
an RCA cord.
¡When you connect a Panasonic car navigation system with a built-in DVD
player, connect a video control lead as well. (apage 72)
VTR2VTR1VIDEO-CNT[}] [{] 
[]][[]
(Select)
[ENTER]
[MODE]
(End)
[MENU] 
424333E
N
G
L
I
S
H
34E
N
G
L
I
S
H
CQ-VD7200U
CQ-VD7200U
SET-UP: User Settings
(continued)
Memory ClearanceThe state of all of the current memories are
returned to default settings.
1
2
: no memory clear. 
The display returns to the previous one.
: default settings
YESNO
[}] [{] []] [[]
(Select)
[ENTER] [MENU] 
q
Press 
[}]
or [{]
to
select 
“etc
”.
w
Press 
[ENTER]
to set.
etc
q
Press 
[}]
or [{]
to
select 
“MEMORY CLEAR
”.
w
Press 
[ENTER]
to set.
MEMORY CLEARq
Press 
[}]
or [{]
to
select 
“VTR SKIP
”.
w
Press 
[ENTER]
to set.
VTR SKIP
[MODE]
(End)
Menu
Submenu
q
Press 
[[]
or []]
to select NO
or YES.
w
Press 
[ENTER]
to set.
VTR skip
: skip VTR1
: not skip VTR1
VTR skip
: skip VTR2
: not skip VTR2
ONOFFVTR 2ONOFFVTR 1
q
Press [}] or[{]to select an item.
w
Press 
[[]
or []]
to select the 
setting.
e
Press 
[ENTER]
to set.
Button Operation Sound Default: ON
Note: The beep sound cannot be silenced
when the display opens and closes.Caution: Be aware that this setting
restores the unit to default settings, so
that all the memories and settings that
you have set will be eliminated.VTR skipDefault: ON
If a VTR is not used, the VTR mode is skipped
when changing the mode.
Video Control Setting This “Video Control Setting” is required
when you connect a Panasonic car navi-
gation system with a built-in DVD player
(available in future).
Default: VTR1
qPress [MENU]to
display the menu.
w
Press 
[[]
or []]
to
select “USER”. 
AUDIOCAPTURE
DATEDVDSCREENUSER