Panasonic Massage Lounger Ep1061 Operating Instructions

							EP1061/EP1060EP1061/EP1060
EP1060 EP1061
Before operating this unit, please read these instructions completely, and save for future reference.
Antes de utilizar esta unidad, lea completamente estas instrucciones y gu‡rdelas por si necesita consultarlas en el futuro.
Sillón de masaje
Instrucciones de uso
Modelo No.
Panasonic Consumer
Electronics CompanyOne Panasonic Way 3D-1
Secaucus, New Jersey 07094
1-800-338-0552 for questions and comments.
www.panasonic.com/massage
No.2 EN, SP
¢žÝ槣

Printed in Japan P90101060231 
						

							English See page 3-28
Español Ver págs 29-54INDEX / íNDICE
Thank you for purchasing the Panasonic Swede-Atsu
TMMassage Lounger EP1061/EP1060.  Please read this
manual carefully to ensure optimum performance and safety.  
IMPORTANT SAFETY INSTRUCTIONSBasic precautions should always be followed when using an electrical unit, including the following.
Please ensure that you read all instructions before using the Household Massage Lounger.DANGER 
– To reduce the risk of electric shock: 
1. Always unplug the unit immediately after use.  
2. Always unplug the unit before cleaning.
WARNING 
– To reduce the risk of burns, fire, electric shock, or injury to persons:
1. Always insert the power plug all the way into the socket to reduce the risk of short-circuit and fire.
2. The unit should never be left unattended when plugged in.  Always unplug the unit when not in use.
3. Close and continuous supervision are necessary when the unit is used by people who are limited in their ability
to move or communicate. 
4. Only use the unit for the purpose described in these instructions.
5. Do not stand on the unit.
6. Do not use any accessories other than those recommended by the manufacturer.
7. This unit should not be used by children.  Keep children away from the unit.  Always return the seat to the
upright position and retract the legrest completely to avoid possible injury.  Make sure that nothing is in the way
when retracting the legrest. 
8. Never operate the unit if it has a damaged power cord or plug.  Return the unit to the nearest authorized service
center if it is not working properly, if it has been dropped or damaged, or if it has been immersed in water. 
9. Always raise the center cushion to check that the fabric of the unit itself has not been ripped before using the
unit.  Please also check other areas to ensure that the fabric has not been ripped.  No matter how small the rip,
if you find one then immediately stop using the unit, unplug the power cord and have the unit repaired at an
authorized service center.
10. Keep power cords away from heated surfaces.  Do not allow pins, rubbish or moisture to come into contact with
the plug.  Do not use the unit on top of heating appliances, such as electric carpets, etc.  
11. Never block the air openings during operation and make sure that all air openings are kept free of lint and hair, etc.
12. Do not drop or insert anything into any of the openings of the unit.  
13. Do not use the unit in bathrooms or other damp or humid places as this may cause electric shock or cause the
unit to malfunction.  Do not spill water, etc. onto the controller.  
14. Do not use the unit outdoors.
15. Do not use the unit in places where aerosol spray products are in use or where oxygen is handled.  
16. When unplugging the unit, turn off all controls before removing the plug from power socket.  Do not use the unit
with a transformer as this may lead to malfunction or electric shock. 
17. Connect this unit to a properly grounded outlet only.  See Grounding Instructions.
18. To avoid electric shock or injury, do not attempt to open or disassemble any part of the unit as it contains no
user-serviceable parts.  
SAVE THESE INSTRUCTIONS 
3 
						

							English See page 3-28
Español Ver págs 29-54INDEX / íNDICE
Thank you for purchasing the Panasonic Swede-Atsu
TMMassage Lounger EP1061/EP1060.  Please read this
manual carefully to ensure optimum performance and safety.  
IMPORTANT SAFETY INSTRUCTIONSBasic precautions should always be followed when using an electrical unit, including the following.
Please ensure that you read all instructions before using the Household Massage Lounger.DANGER 
– To reduce the risk of electric shock: 
1. Always unplug the unit immediately after use.  
2. Always unplug the unit before cleaning.
WARNING 
– To reduce the risk of burns, fire, electric shock, or injury to persons:
1. Always insert the power plug all the way into the socket to reduce the risk of short-circuit and fire.
2. The unit should never be left unattended when plugged in.  Always unplug the unit when not in use.
3. Close and continuous supervision are necessary when the unit is used by people who are limited in their ability
to move or communicate. 
4. Only use the unit for the purpose described in these instructions.
5. Do not stand on the unit.
6. Do not use any accessories other than those recommended by the manufacturer.
7. This unit should not be used by children.  Keep children away from the unit.  Always return the seat to the
upright position and retract the legrest completely to avoid possible injury.  Make sure that nothing is in the way
when retracting the legrest. 
8. Never operate the unit if it has a damaged power cord or plug.  Return the unit to the nearest authorized service
center if it is not working properly, if it has been dropped or damaged, or if it has been immersed in water. 
9. Always raise the center cushion to check that the fabric of the unit itself has not been ripped before using the
unit.  Please also check other areas to ensure that the fabric has not been ripped.  No matter how small the rip,
if you find one then immediately stop using the unit, unplug the power cord and have the unit repaired at an
authorized service center.
10. Keep power cords away from heated surfaces.  Do not allow pins, rubbish or moisture to come into contact with
the plug.  Do not use the unit on top of heating appliances, such as electric carpets, etc.  
11. Never block the air openings during operation and make sure that all air openings are kept free of lint and hair, etc.
12. Do not drop or insert anything into any of the openings of the unit.  
13. Do not use the unit in bathrooms or other damp or humid places as this may cause electric shock or cause the
unit to malfunction.  Do not spill water, etc. onto the controller.  
14. Do not use the unit outdoors.
15. Do not use the unit in places where aerosol spray products are in use or where oxygen is handled.  
16. When unplugging the unit, turn off all controls before removing the plug from power socket.  Do not use the unit
with a transformer as this may lead to malfunction or electric shock. 
17. Connect this unit to a properly grounded outlet only.  See Grounding Instructions.
18. To avoid electric shock or injury, do not attempt to open or disassemble any part of the unit as it contains no
user-serviceable parts.  
SAVE THESE INSTRUCTIONS 
3 
						

							OPERATING PRECAUTIONSWARNING: To avoid damaging to the chair, follow these precautions:1. The chair is designed for a maximum user weight of 264lbs (120kg).  Exceeding the maximum weight may
cause permanent damage to the massage mechanism and/or other components of the chair.  Any such
damage is deemed to be user abuse and is not covered under the Limited Warranty.  
2. Do not sit on or drop the controller.  Do not pull the controller cord or the power cord.  Be careful not to catch
the cord of the controller between the armrest and the chair back.  
3. Do not treat the chair roughly, such as turning the chair on its side, turning the chair over or standing on it.  
4. Do not treat the covering roughly.
• Keep sharp or pointed objects away from the covering of the chair. Be careful not to drop lit ashes, lit cigarette
or matches on the chair.  
• Exposure to direct sunlight can cause fading or a change in color of the covering.
5. If the massager functions abnormally, immediately turn off the power and have the massager checked by an
authorized service center.
6. Do not attempt to repair the massager yourself.  
7. Do not repeatedly operate any switch at short intervals. Such action may cause the switch to malfunction.
8. Some noise may be heard coming from the massager while in use.  This is due to the structure of the
massager and is normal.  
9. Make sure there are no obstacles behind the chair before reclining it.  The chair can be reclined to a maximum
angle of 170°.  If the back hits a wall or pillar, the chair may malfunction. Be sure to have ample space behind
the chair. Recline the chair slowly in order to avoid contact with an obstacle.
10. When excessive pressure is applied to the massage heads, they may stop moving for safety. When moving the
heads up from the lowered position, one’s body weight may stop the heads’ movement. In such case, slightly
raise the body and allow the massage heads to move up.
11. After each massage, slide the power switch, which is located on the back of the chair, to the “off” position and
turn its lock switch to the “lock” position.
12. Do not sit on massage chair with wet body or hair. 
13. The massage Lounger must not be used in “wet rooms” (sauna, swimming pool) or out of doors. 
SAFETY PRECAUTIONSWARNING: To avoid the risk of injury, follow these precautions:1. Pregnant women, people who are ill, in poor physical shape or undergoing medical treatment, and people
suffering from back, neck, shoulder or hip pain should consult their doctor before using the unit.  If you have a
pacemaker, defibrillator, or other personal medical device, consult with the manufacturer of your device before
using the unit.  Your physician may be able to assist you in obtaining this information.  
2. Sit down slowly after checking the position of the massage heads.  Never put any part of your body between
the massage heads as the squeezing action of the massage heads may cause injury.  Never put your fingers or
feet in the gap between the backrest and seat, the backrest and the armrest, the seat and cover under the
armrest, or the gap between the legrest and the footrest.  Do not place your fingers or any part of your body in
the mechanical section of the legrest located under the seat.
3. Do not use the unit against bare skin.  While thin clothing may increase effectiveness, exposing the skin directly
to the massager may irritate the skin.  
Do not use the unit while wearing anything hard on your head like a hair accessory, etc.  
4. Do not use the unit for massaging the head, abdomen, elbows or knees.   
5. Always check that the shoulder position is correct.  If it is not correct, use the Neck Roller Position Adjustment
Button to adjust it properly (In programmed operation). 
6. Do not stretch the back muscles for more than approximately 15 minutes at a time.  To avoid overstretching the
muscles which may result in discomfort, do not use the unit for more than 5 minutes when first using it.  You
can gradually increase the duration and intensity of the massage as you become used to it.  
Do not massage any one point for more than 5 minutes at a time.  
To prevent excessive massaging, do not use the massager for more than a total of 15 minutes each session.
After approximately 15 minutes, the massage heads will be retracted and stop moving.  
7. While using the unit, if you start feeling sick or if the massage seems painful, stop using it immediately.  
While using the massager, if the pressure seems too strong, the movement of the massage heads can be
stopped at any time by pressing the Stop Button.
8. Do not go to sleep while using the unit.  Do not use the unit after drinking alcohol.  
9. When the seat back is in a reclined position, do not sit on it or sit with your legs resting on the headrest.  
Do not sit on the legrest as the unit may fall over.
10. Do not allow children or pets to play on or around the unit, especially during operation.  
11. Do not unplug the unit or turn it off during operation.  Unplug the unit immediately if there is a power
interruption.  
12. For those who are trying the massage for the first time, it is recommended to start on the gentle massage
program. The shiatsu massage is stronger and should be enjoyed after one has gotten accustomed to the
chair.
45
CARING FOR THE MASSAGER• Always unplug the chair before cleaning.
• If the covering becomes soiled, dampen with liquid soap and brush the surface. Wipe with a cloth dampened with
water.  Allow to dry naturally.  If the plastic portions become soiled use lukewarm water, with liquid soap on a soft
cloth, to clean the surface.
• Do not use thinner, benzene or other solvent-type cleaners. Chemicals can discolor or damage the materials. 
						

							OPERATING PRECAUTIONSWARNING: To avoid damaging to the chair, follow these precautions:1. The chair is designed for a maximum user weight of 264lbs (120kg).  Exceeding the maximum weight may
cause permanent damage to the massage mechanism and/or other components of the chair.  Any such
damage is deemed to be user abuse and is not covered under the Limited Warranty.  
2. Do not sit on or drop the controller.  Do not pull the controller cord or the power cord.  Be careful not to catch
the cord of the controller between the armrest and the chair back.  
3. Do not treat the chair roughly, such as turning the chair on its side, turning the chair over or standing on it.  
4. Do not treat the covering roughly.
• Keep sharp or pointed objects away from the covering of the chair. Be careful not to drop lit ashes, lit cigarette
or matches on the chair.  
• Exposure to direct sunlight can cause fading or a change in color of the covering.
5. If the massager functions abnormally, immediately turn off the power and have the massager checked by an
authorized service center.
6. Do not attempt to repair the massager yourself.  
7. Do not repeatedly operate any switch at short intervals. Such action may cause the switch to malfunction.
8. Some noise may be heard coming from the massager while in use.  This is due to the structure of the
massager and is normal.  
9. Make sure there are no obstacles behind the chair before reclining it.  The chair can be reclined to a maximum
angle of 170°.  If the back hits a wall or pillar, the chair may malfunction. Be sure to have ample space behind
the chair. Recline the chair slowly in order to avoid contact with an obstacle.
10. When excessive pressure is applied to the massage heads, they may stop moving for safety. When moving the
heads up from the lowered position, one’s body weight may stop the heads’ movement. In such case, slightly
raise the body and allow the massage heads to move up.
11. After each massage, slide the power switch, which is located on the back of the chair, to the “off” position and
turn its lock switch to the “lock” position.
12. Do not sit on massage chair with wet body or hair. 
13. The massage Lounger must not be used in “wet rooms” (sauna, swimming pool) or out of doors. 
SAFETY PRECAUTIONSWARNING: To avoid the risk of injury, follow these precautions:1. Pregnant women, people who are ill, in poor physical shape or undergoing medical treatment, and people
suffering from back, neck, shoulder or hip pain should consult their doctor before using the unit.  If you have a
pacemaker, defibrillator, or other personal medical device, consult with the manufacturer of your device before
using the unit.  Your physician may be able to assist you in obtaining this information.  
2. Sit down slowly after checking the position of the massage heads.  Never put any part of your body between
the massage heads as the squeezing action of the massage heads may cause injury.  Never put your fingers or
feet in the gap between the backrest and seat, the backrest and the armrest, the seat and cover under the
armrest, or the gap between the legrest and the footrest.  Do not place your fingers or any part of your body in
the mechanical section of the legrest located under the seat.
3. Do not use the unit against bare skin.  While thin clothing may increase effectiveness, exposing the skin directly
to the massager may irritate the skin.  
Do not use the unit while wearing anything hard on your head like a hair accessory, etc.  
4. Do not use the unit for massaging the head, abdomen, elbows or knees.   
5. Always check that the shoulder position is correct.  If it is not correct, use the Neck Roller Position Adjustment
Button to adjust it properly (In programmed operation). 
6. Do not stretch the back muscles for more than approximately 15 minutes at a time.  To avoid overstretching the
muscles which may result in discomfort, do not use the unit for more than 5 minutes when first using it.  You
can gradually increase the duration and intensity of the massage as you become used to it.  
Do not massage any one point for more than 5 minutes at a time.  
To prevent excessive massaging, do not use the massager for more than a total of 15 minutes each session.
After approximately 15 minutes, the massage heads will be retracted and stop moving.  
7. While using the unit, if you start feeling sick or if the massage seems painful, stop using it immediately.  
While using the massager, if the pressure seems too strong, the movement of the massage heads can be
stopped at any time by pressing the Stop Button.
8. Do not go to sleep while using the unit.  Do not use the unit after drinking alcohol.  
9. When the seat back is in a reclined position, do not sit on it or sit with your legs resting on the headrest.  
Do not sit on the legrest as the unit may fall over.
10. Do not allow children or pets to play on or around the unit, especially during operation.  
11. Do not unplug the unit or turn it off during operation.  Unplug the unit immediately if there is a power
interruption.  
12. For those who are trying the massage for the first time, it is recommended to start on the gentle massage
program. The shiatsu massage is stronger and should be enjoyed after one has gotten accustomed to the
chair.
45
CARING FOR THE MASSAGER• Always unplug the chair before cleaning.
• If the covering becomes soiled, dampen with liquid soap and brush the surface. Wipe with a cloth dampened with
water.  Allow to dry naturally.  If the plastic portions become soiled use lukewarm water, with liquid soap on a soft
cloth, to clean the surface.
• Do not use thinner, benzene or other solvent-type cleaners. Chemicals can discolor or damage the materials. 
						

							7 6
PART NAMES AND FUNCTIONSSEAT
on
off
lock openlock switch
BackrestArmrest
• Push up the center cushion for a 
stronger massage if the massage 
feels too weak.
Center Cushion with
Integrated Pillow
Controller
Back Cushion ZipBack CushionController
Controller Pocket
SeatLegrestBack Cover
Back Cover HandlesSafety Precaution Label
Wheels
Power SwitchLock Switch
Soles of feet Calves
2 way roller massage
EP1061
EP1060
GROUNDING INSTRUCTIONS•The product must be grounded.  If it should malfunction, grounding provides the path of least resistance for
electric current to reduce the risk of electric shock.  
•This product is equipped with a cord having an equipment-grounding conductor and a grounding plug.  The plug
must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local
codes and ordinances.DANGER•Improper connection of the equipment-grounding conductor can result in a risk of electric shock.  Check with a
qualified electrician if you are in doubt as to whether the product is properly grounded.  Do not modify the plug
provided with the product even if it does not fit the outlet.  Have a proper outlet installed by a qualified electrician.  
•This product is for use on a nominal 120-volt circuit and has
a grounding plug that looks like the plug shown in Figure A.
Make sure that the product is connected to an outlet having
the same configuration as the plug.  No adaptor should be
used with this product.HOW TO MOVE THE CHAIRCAUTIONDo not move the chair while someone is sitting in it.
Failure to observe this point may cause the chair to tip over, possibly resulting in personal injury.Use the casters to move the chair.•Do not attempt to move the chair by lifting from the front (right illustration). The correct way to move the chair is by
putting your foot on the caster and pushing down from behind the chair (left illustration).
•It is easier to move the chair if the massage heads have been moved to their resting positions and the backrest
reclined.
•Moving the chair may damage easily marked floor surfaces, therefore, place a mat or cloth on the floor and move
the chair slowly.
•Before pushing down the chair, prepare yourself for its weight and exercise caution when moving it.
Figure A
GROUNDING
PIN
GROUNDED 
OUTLET
CORRECT WRONG  
Caster 
						

							7 6
PART NAMES AND FUNCTIONSSEAT
on
off
lock openlock switch
BackrestArmrest
• Push up the center cushion for a 
stronger massage if the massage 
feels too weak.
Center Cushion with
Integrated Pillow
Controller
Back Cushion ZipBack CushionController
Controller Pocket
SeatLegrestBack Cover
Back Cover HandlesSafety Precaution Label
Wheels
Power SwitchLock Switch
Soles of feet Calves
2 way roller massage
EP1061
EP1060
GROUNDING INSTRUCTIONS•The product must be grounded.  If it should malfunction, grounding provides the path of least resistance for
electric current to reduce the risk of electric shock.  
•This product is equipped with a cord having an equipment-grounding conductor and a grounding plug.  The plug
must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local
codes and ordinances.DANGER•Improper connection of the equipment-grounding conductor can result in a risk of electric shock.  Check with a
qualified electrician if you are in doubt as to whether the product is properly grounded.  Do not modify the plug
provided with the product even if it does not fit the outlet.  Have a proper outlet installed by a qualified electrician.  
•This product is for use on a nominal 120-volt circuit and has
a grounding plug that looks like the plug shown in Figure A.
Make sure that the product is connected to an outlet having
the same configuration as the plug.  No adaptor should be
used with this product.HOW TO MOVE THE CHAIRCAUTIONDo not move the chair while someone is sitting in it.
Failure to observe this point may cause the chair to tip over, possibly resulting in personal injury.Use the casters to move the chair.•Do not attempt to move the chair by lifting from the front (right illustration). The correct way to move the chair is by
putting your foot on the caster and pushing down from behind the chair (left illustration).
•It is easier to move the chair if the massage heads have been moved to their resting positions and the backrest
reclined.
•Moving the chair may damage easily marked floor surfaces, therefore, place a mat or cloth on the floor and move
the chair slowly.
•Before pushing down the chair, prepare yourself for its weight and exercise caution when moving it.
Figure A
GROUNDING
PIN
GROUNDED 
OUTLET
CORRECT WRONG  
Caster 
						

							9
CAUTION•Do not use the unit in areas with high humidity, such
as the bathroom, etc. as this can lead to electric
shock or other accidents.
•Place the unit on a totally flat surface. Failure to do
so may result in the seat tipping over.WHERE TO USE THE UNITSETTING UP THE MASSAGE LOUNGER
16in.
40cm16in.
40cm
Ensure there is Adequate Space for Reclining•Ensure that there is approximately 16in. (40cm) behind and at
least 16in. (40cm) in front of the unit.Places to Avoid•Do not use the unit in direct sunlight or in places where it will
be exposed to high temperatures, such as in front of a heater,
etc. as this can cause discoloration or hardening of the
synthetic leather.
8
CONTROLLER (
EP1061)PART NAMES AND FUNCTIONS
programmed operation
whole backgentle strong
neck roller position
reclining
programmed
operation
/manual
operation
lower back neck, shoulder
tap on/off vibration on/off
slow fast
intensity
leg massage
neck roller position
reclining
programmed
operation
/manual
operation
intensityroll manual operation
whole back
regional tap A vibration tap Bswedish shiatsu knead
position
slow fastleg massage
ON/OFF ButtonON/OFF Lamp
Cover Closed Cover Open
¥ Used to stop the massage
immediately.
Quick Stop Button
¥ Used to adjust the angle of
the backrest and legrest.
Reclining Button
¥ Displays operational mode.
Movement IndicatorManual Operation
Selection Buttons
¥ Used in Programmed
Operation.Tapping ON/OFF Button
Cover
Massage Head
Adjustment Buttons
¥ Used to adjust the shoulder
position.
Shoulder Position
Adjustment Button
Shoulder Position IndicatorProgrammed Operation Buttons¥ Used for selecting the area
for concentrated massage.Concentrated Area Buttons¥ Used in Programmed
Operation.Vibration ON/OFF Button
Intensity Indicator
¥ Used to adjust the intensity of
the massage (3-stage).Intensity Adjustment Button¥ Used to turn on/off and adjust
the leg roller massage unit.
Leg Massage Button
gentle strongleg massage
¥ Used to turn on/off and adjust
the leg vibration massage
unit.
Leg Massage ButtonCONTROLLER (
EP1060) 
						

							9
CAUTION•Do not use the unit in areas with high humidity, such
as the bathroom, etc. as this can lead to electric
shock or other accidents.
•Place the unit on a totally flat surface. Failure to do
so may result in the seat tipping over.WHERE TO USE THE UNITSETTING UP THE MASSAGE LOUNGER
16in.
40cm16in.
40cm
Ensure there is Adequate Space for Reclining•Ensure that there is approximately 16in. (40cm) behind and at
least 16in. (40cm) in front of the unit.Places to Avoid•Do not use the unit in direct sunlight or in places where it will
be exposed to high temperatures, such as in front of a heater,
etc. as this can cause discoloration or hardening of the
synthetic leather.
8
CONTROLLER (
EP1061)PART NAMES AND FUNCTIONS
programmed operation
whole backgentle strong
neck roller position
reclining
programmed
operation
/manual
operation
lower back neck, shoulder
tap on/off vibration on/off
slow fast
intensity
leg massage
neck roller position
reclining
programmed
operation
/manual
operation
intensityroll manual operation
whole back
regional tap A vibration tap Bswedish shiatsu knead
position
slow fastleg massage
ON/OFF ButtonON/OFF Lamp
Cover Closed Cover Open
¥ Used to stop the massage
immediately.
Quick Stop Button
¥ Used to adjust the angle of
the backrest and legrest.
Reclining Button
¥ Displays operational mode.
Movement IndicatorManual Operation
Selection Buttons
¥ Used in Programmed
Operation.Tapping ON/OFF Button
Cover
Massage Head
Adjustment Buttons
¥ Used to adjust the shoulder
position.
Shoulder Position
Adjustment Button
Shoulder Position IndicatorProgrammed Operation Buttons¥ Used for selecting the area
for concentrated massage.Concentrated Area Buttons¥ Used in Programmed
Operation.Vibration ON/OFF Button
Intensity Indicator
¥ Used to adjust the intensity of
the massage (3-stage).Intensity Adjustment Button¥ Used to turn on/off and adjust
the leg roller massage unit.
Leg Massage Button
gentle strongleg massage
¥ Used to turn on/off and adjust
the leg vibration massage
unit.
Leg Massage ButtonCONTROLLER (
EP1060) 
						

							11 10
1. Check the Surrounding Area
zCheck that there is nothing behind the unit.  
xCheck that there is enough room to recline the unit.
•In the interests of safety, the unit may stop moving if it hits
something while reclining.
2. Check the Unit
zLift up the pillow and the center cushion to check
that there are no rips in the fabric of the back
cushion, etc.
xCheck that the power plug has not been damaged
or has pins or dust sticking to it.  AFTER CHECKING THE SURROUNDING AREA, TURN ON THE POWERBEFORE USING THE UNIT
Do not leave 
anything here.
16in.
(40cm)16in.
(40cm)
Main Cushion Fabric
Check
3. Turn the Power On
zPlug the power plug into the power socket.
xTurn the lock switch to the “open” position.
cTurn on the power switch on the back of the unit.When plugging the unit in, make sure that there is at least 4in.
(10cm) slack in the power cord.
(Take care to ensure that the power cord is not caught by the
unit when it reclines.)
2
3
1
on
off
lock openlock switch
1. After Carrying Out Safety Checks, Turn the Unit On (See Page 11)
zPlug the power plug into the power socket. 
xTurn the lock switch to the “open” position.
cTurn on the power switch on the back of the unit.• Please always check for the following before using the unit.
- Check that there is no person, pets, or obstacles around the unit.
- Check that there are no rips in the fabric.
2. Press button.
•When you press  button, the Programmed Operation and Leg Massage 
Buttons will flash.  If the cover of the controller is open, then the Manual Operation Selection Buttons will flash.
3. Select the Desired Program or the Desired Movement on the Manual Operation
(See details on page 14)
Programmed Operation• Ideal for people who feel tired all over.
• Ideal for people who want to operate the massage lounger simply.zSelect the required program.
xPress the Neck/Shoulder or Lower Back Buttons if you want to focus on a particular area.
cThe chair will recline to the optimum angle for the massage.  The massage will then begin
and continue until the end of the selected program is reached, at which time the massage
will automatically stop. An average program massage is 15-17 minutes.
Manual Operation  • Used for selecting a particular massage movement or area to be massaged.
• Ideal for people who want to adjust movement and location during the course of a massage.
• Ideal for people who want just a little more on the shoulders at the end of their massage.zOpen the cover of the controller and select the massage required.
xThe seat will automatically recline to the optimum massage position.
cAdjust the position and intensity of the massage rollers.
vPress 
button 
to complete the massage.
4. Adjust the Angle of the Backrest and Legrest (See Page 13)
•Adjust the angle of the backrest and legrest to the most comfortable position.•When retracting the backrest, as the massage heads must be retracted in the interests
of safety there may be a slight delay before the backrest actually starts to retract.
Please continue to hold down the Reclining Button until the backrest is fully retracted.  
5. Turn the Power Off to Finish the Massage
(See Page 20)
zTurn the power switch to the “off” position.
xTurn the lock switch the “lock” position.
cUnplug the power cord.
•Here you will find an overview of how to use the massage lounger.  Please refer to the pages shown for further details.HOW TO USE THE MASSAGE LOUNGER — INTRODUCTION
2
3
1
on
off
lock openlock switch
32
1
on
off
lock openlock switch
If excessive pressure is applied to the massage heads during upper body massage, in the interests
of safety the massage heads may stop moving.  If this occurs, raise your body slightly before
restarting it.  (This may happen more frequently for people with a weight of 220 lbs. or more.)
If the massage mechanism stops (or if all markings and buttons on the controller start to flash), turn
off the power switch, wait for approximately 10 seconds, and then turn the power switch on again.
After each use•Be sure to tum the power switch to “off”.
•To prevent children from using this unit, lock the power switch by moving the
operating lock switch to the “lock” position.
•As a further precaution, unplug the power cord from the outlet after each use.NOTE:Be careful not to pinch the cord under the leg frames of the chair or any other objects.
NOTE:The operating lock
switch prevents the unit
from being turned on
when switch is in the
“lock” position.