Panasonic Memory Card Video Recording System AG-CPD10CRU Operating Instructions

21
Notes on handling
Installation
• Install the recorder and camera
properly as described in the
installation manual, so that the
units cannot come loose or fall off.
• Do not place heavy objects on the
power cable and other connection
cables.
• Do not exceed the rating of any
connection cables and other wiring
parts.
• Use only the supplied accessories
and specified optional accessories.
• Keep the recorder, camera, P2
card, power cable and connection
cables away from heat sources.
• Protect the...

22
• Do not disconnect the power cable
while the recorder is operating. Be
sure to perform recorder shutdown
before disconnecting the cable.
Otherwise recorder setting files
and P2 card managing information
may be lost or damaged.
When the SIGNAL pin at the DC
IN connector goes OFF, the
recorder will perform shutdown
after an interval set with the
Toughbook-Arbitrator Front End
Software.
• Do not open the cover during P2
card access (BUSY LED is lit or
flashing). Do not exert undue force
on the cover to...

23
Factory default settings
The factory default settings are listed in the table below. To change any of these
settings, use the Toughbook-Arbitrator Front End Software, but “17 IP Address”
will not be changed.
Item Value Description
(Recorder related settings)
Shift
Shift Start 2005-01-01 Shift start date, time and day
1
09:00
SAT
Shift End 2005-01-01 Shift end date, time and day
1
17:00
SAT
Shift Pattern ---- Shift pattern
Officer
Officer1 first name---- Officer 1 first name
Officer1 mid name- Officer...

24
Factory default settings(continued)
8 V-CH 1 Video input
Setting values1: Camera cable connector input
2: VIDEO IN connector input
9 AUDIO2 MIC Audio input
Setting values: AUDIO IN2
MIC
(For information on audio settings, see page 18.)
10 Pre Time 120 Prerecord time (seconds)
Setting values: 0 - 180
11 Post Time 120 Post-record time (seconds)
Setting values: 0 - 180
12 Power On/Off 120 Time lag between SIGNAL off and 
recorder shutdown (minutes)
Setting values: 0 - 1801
13 P-Rec OFFAutomatically start...

25
Factory default settings(continued)
OSD
OSD On/Off OSD On OSD enable/disable
GPIO On
Setting values: OSD OFF
TimeDate OnOSD ON, GPIO ON, TimeDate ON
OSD ON, GPIO ON, TimeDate OFF
OSD ON, GPIO OFF, TimeDate ON
TIME-DATE ISO Time/Date display format
STYLE Setting values: ISO (ISO format)
USA (USA format)
--- 1lineUpper Display position
Setting values:
1lineUpperEnd:1-line display, upper end
1lineUpper
:1-line display, top
1lineBottom
:1-line display, bottom
1lineBottomEnd
:1-line display, bottom end...

26
Factory default settings(continued)
R-Protocol
Baud Rate 4800 Radar gun communication rate (bps)
Setting value: 50 - 230400
Bit Length 8 Communication word length (bits)
Setting values: 8
7
Stop Bit 1 Stop bits (bit)
Setting value: 1,2
Parity NON Parity
Setting values: ODD
NON
EVEN
Delimit OFF Delimiter
Character
Setting value: OFF
\D
 A
Buffer Size 255 Transfer buffer size (bytes)
Setting value: 0 - 256
Data timeout 1 Transfer timeout (100 msec.)
Setting value: 1 - 999
IP Address
192.168.10.10/24IP...

27
Factory default settings(continued)
(Camera related settings)
1 ZOOM-LIM 22 Maximum zoom factor
Target MagnificationSetting values: 22 - 220
(The values except 22 are multiples of 20.)
1 - 220
(Values from 1 to 22 are integers, and values
of 40 and above are multiples of 20.)
2 AUTO ZOOM 10Target zoom factor when AutoZoom command is received
Target MagnificationSetting values: 1 - 22 (integers)
3 AUTO ZOOM 3
Interval of maintaining target zoom 
Maintenance Timefactor when AutoZoom command is received...

28
Factory default settings(continued)
7 Infra Red AUTOIR function auto switch/always ON/always OFF2
Setting values:
AUTO (IR function is automatically switched on and off)
ON (IR function is always on)
OFF (IR function is always off)
8 IR-Level LOW
Level setting for IR auto switching mode2
Setting values: LOW
HIGH
9 IR-Time 30 Detection time setting for IR auto 
switching mode (seconds)
2
Setting values: 10: 10 seconds
30: 30 seconds
60: 60 seconds
300: 300 seconds
10 AGC HIGH Camera input gain setting...

29
Connector signals
1N.C.
2V_OUT
3BL_L
4AUTO_ZOOM_L
5REC_L
6GND (DC_IN)
7DC_IN
8N.C.
9GND (SHIELD)
10GND (V_OUT)
11GND (TxD/RxD)
12TxD
13RxD
14REC_LED_L
15GND (SHIELD)
16GND (SHIELD)
Camera cable connector
(recorder/female)
1GND Black
2BATT Red
3SIGNAL White
4N.C.
DC IN connector
(recorder/female)
Pin 
numberSignal
Pin 
numberSignal Cable color
1
9168
1
4
Power cable (supplied)
Red Black
White
The SIGNAL pin can be used to turn power to the recorder on and off. When an
OFF signal is input at this pin...

30
Connector signals(continued)
1N.C.
2TxD Serial
3RxD Serial
4RTS Serial
5CTS Serial
6DSR Serial
7SG Serial
8CD Serial
9GND GPIO Black
10GPIO1 In Brown
11GPIO2 In Red
12GPIO3 In Orange
13GPIO4 In Yellow
14N.C.
15N.C.
16N.C.
17N.C.
18N.C.
19N.C.
20DTR Serial
21GPIO5 In Green
22GPIO6 In Blue
23GPIO7 In Purple
24GPIO8 In Gray
25GPIO9 Out White
GPIO/Serial connector
(recorder/female)Pin 
numberSignal RemarksCable
color
13
25141
External 
trigger cable 
(supplied)
Brown
Red
Orange
Yellow
Green
Blue
Purple...