Panasonic Monitor Bt H1700ae Owners Manual
Have a look at the manual Panasonic Monitor Bt H1700ae Owners Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
ENGLISH 1. Attach the Power Cord Holder case to the AC inlet on the back of the monitor with 2 screws (provided). 2 Attach the Power Cord Holder cover to the AC power cord. 3. Connect the AC power cord to the AC inlet, and join the Power Cord Holder cover with the case. ATTACHING THE POWER CORD HOLDER The provided Power Cord Holder prevents accidental disconnection of the AC power cord from the AC inlet. The Power Cord Holder consists of two parts; a case and cover. Press the cover until it clicks. Hold until it clicks. Caution: A different plug shape will result in the cover being attached to a different position. Check to make sure the plug doesnt pull out after the cover is attached. Caution: Use only the provided screws. Note: To disconnect the power cord, click the tab to open the cover. 9 LCT1261-001A (EN)02.6.25, 12:25 PM 11
BASIC MENU OPERATIONS
(MAIN MENU, SETUP MENU)
ABOUT MENU SCREENS
This monitor features a MAIN MENU (main menu screen) and
a SETUP MENU (setup menu screen).
The MAIN MENU contains the functions normally used, and
the SETUP MENU contains the settings required for initial
setup.
FUNCTION SETTING
PICTURE SUB ADJ.
COLOR TEMP/BAL.
SIZE/POSI.ADJ.
DISTORTION ADJ.
STATUS DISPLAY
CONTROL LOCK :ON
all reset
EXIT:
MENU ENTER:+ SELECT:
APERTURE CONTROL
SLOT CONDITION
sub menu POSITION :LOWER
AREA MARKER :OFF
AREA MARKER-R :OFF
CENTER MARKER :OFF
COLOR MATRIX
EXIT:
MENU ENTER:+ SELECT:
APERTURE CONTROL
SLOT CONDITION
sub menu POSITION :LOWER
COLOR MATRIX
EXIT:
MENU ENTER:+ SELECT:
SLOT CONDITION
sub menu POSITION :LOWER
EXIT:
MENU ENTER:+ SELECT:
DISPLAYING THE MENU
SCREENS
●To display MAIN MENU
Press the
MENU button on the front panel.
●To display SETUP MENU
Press the
button while pressing the button on the
front panel.
VOLUMESLOT 1A
B DEGAUSS
MENU
BLUE
CHECKASPECT
AREA
MARKER UNDER
SCANPULSE
CROSSCOLOR
OFFSLOT 2C
DSLOT 3POWERE
FINPUT SELECT
VOLUMEDEGAUSS
MENU
MUTING
MUTING
CLOSING THE MENU
SCREENS
●Using the MENU button
Press the
MENU button a few times until the Menu Screen
disappears.
●With no operation
When approx. 30 seconds have passed since the last Menu
operation, both screens will disappear.
* Some items on the Menu Screens disappear automatically
after setting.
NOTE :When you perform the “reset” or “all reset” function,
the Menu Screen does not disappear unless you
press the
MENU button.
BASIC MENU OPERATION
●To select an item,
Press the or buttons to move the cursor (4) on the
Menu Screens and select the desired item.
●To set (select) or adjust an item,
Press the
or buttons to select or adjust the desired
item.
●When the desired item has other menus (hierarchical
menus),
Press the
button to display the lower hierarchical menu.
●To return to the former Menu Screen,
Press the
MENU button.
APERTURE CONTROL
SLOT CONDITION
sub menu POSITION :LOWER
AREA MARKER :OFF
AREA MARKER-R :OFF
CENTER MARKER :OFF
COLOR MATRIX
EXIT:
MENU ENTER:+ SELECT:
LEVEL :00
CONTROL FREQ. :HIGH
sub menu
reset
EXIT:
MENU ENTER:+ SELECT:
MENU
HOW TO USE THE SUB
MENU
The sub menu function applies to Menu Screen items that
should be adjusted or set while watching the picture. This
function simplifies the adjustment or setting while watching the
picture by displaying the single item on the top or bottom of
the screen.
●To use the sub menu function,
Press the
or buttons to select “ sub menu”. Then,
press the button to display the sub menu screen.
●To adjust or set an item in the sub menu screen,
Press the
or buttons.
●To change the item to be adjusted or set,
Press the
or buttons.
●To change the position of the sub menu screen,
Set “UPPER” (on the top) or “LOWER” (on the bottom) in
“sub menu POSITION” of MAIN MENU.
●To close the sub menu screen,
Press the
MENU button. The previous Menu Screen is
displayed.
CONTRAST : 00
BRIGHT : 00
CHROMA : 00
PHASE : 00
NTSC SETUP : 00
COMPO.LEVEL :SMPTE
sub menu
reset
EXIT:
MENU ENTER:+ SELECT:CONTRAST : 00
- - + +
CONTRAST : 00
- - + +
MAINsMENUsWmainsmenusscreen-
SETUPsMENU
Wsetupsmenusscreen-
Thesupperspalesscreen;swhenssetting
ENGLISH
11
HOW TO USE “MAIN MENU”
“MAIN MENU” ITEMS
The following items appear in MAIN MENU.
ItemsFunctionsDisplays
1 APERTURE CONTROL Compensates the frequency characteristics of the input video signal.*1
2 SLOT CONDITION Displays the status of the input cards installed in each of the input card slots.
3 sub menu POSITION Selects the display position of the sub menu superimposed on the screen.
4 AREA MARKER Selects the size marker for the other screen ratio used when the screen
ratio is 16:9.*2
5 AREA MARKER-R Selects the size marker for the other screen ratio used when the screen ratio is
16:9. (for external control)*2
6 CENTER MARKER Makes the centre marker appear or disappear.*2
7 COLOR MATRIX Selects or adjusts the picture colour matrix.*1
“MAIN MENU” SCREENS
APERTURE CONTROL
SLOT CONDITION
sub menu POSITION :LOWER
AREA MARKER :OFF
AREA MARKER-R :OFF
CENTER MARKER :OFF
COLOR MATRIX
EXIT:
MENU ENTER:+ SELECT:
APERTURE CONTROL
SLOT CONDITION
sub menu POSITION :LOWER
COLOR MATRIX
EXIT:
MENU ENTER:+ SELECT:
SLOT CONDITION
sub menu POSITION :LOWER
EXIT:
MENU ENTER:+ SELECT:
LEVEL : 00
CONTROL FREQ. :HIGH
sub menu
reset
EXIT:
MENU ADJUST:- + SELECT:
INPUT A : VIDEO-1
INPUT B : VIDEO-2
INPUT C : COMPO.
INPUT D : RGB
INPUT E : NO SLOT
INPUT F : NO SLOT
EXIT:
MENU
SELECT :ITU601
EXIT:
MENU ADJUST:- + SELECT:
LEVEL :+05
- - + +
LEVEL :+05
- - + +
R-Y PHASE :+90
- - + +
SELECT :MANUAL
R-Y PHASE : 90
R/B GAIN :0.86
G-Y PHASE : 244
G/B GAIN :0.36
sub menu
reset
EXIT:
MENU ADJUST:- + SELECT:
The menu screen when “sub
menu” is selected. About “Displays”*1: Not displayed when an RGB signal is input.
*2: Displayed only when the screen ratio is 16:9. Not displayed when an RGB signal is input.
When some items are not displayed depending on the input signals, subsequent items will move up.
The sub menu screen when
“sub menu POSITION” is set
to “UPPER”.
The menu screen when
“MANUAL” is selected.The menu screen when “sub
menu” is selected.
The menu screen when the
screen ratio is 4:3The menu screen when an
RGB signal is input
LCT1261-001A (EN)02.6.25, 12:25 PM 13
12
1. APERTURE CONTROL
Compensates the frequency
characteristics of the input
video signal. Press the
button to display the setting
menu illustrated on the right.
NOTE :APERTURE
CONTROL is not
displayed when the
RGB signal is input.
●INPUT A/B corresponds to SLOT 1, INPUT C/D to SLOT 2,
and INPUT E/F to SLOT 3.
●VIDEO-1 or VIDEO-2 shows the video input card is installed.
COMPO. or RGB shows the component/RGB input card.
SDI 1 or SDI 2 shows the SDI input card is installed.
Item : LEVEL
Adjustment
range : 00 ~ +10
Function : Adjusts the compensate value. The higher the
number is, the larger the compensate value gets.
Item : CONTROL FREQ.
Settings : HIGH/LOW/OFF
Function : Adjusts the frequency compensation.
HIGH : Compensates the high frequencies.
LOW : Compensates the low frequencies.
OFF : Deactivates the aperture compensation.
Item : sub menu
Adjustment range/
Settings : Same as LEVEL or CONTROL FREQ.
Function : Performs the LEVEL or CONTROL FREQ.
settings in a single-line display. The display
position depends on the “sub menu POSITION”
setting.
Item : reset
Function : Sets the LEVEL and CONTROL FREQ. values to
factory-preset ones.
2. SLOT CONDITION
Displays the status of the input
cards installed in each of the
input card slots. Press the
button to display the setting
menu illustrated on the right.
INPUT A : VIDEO-1
INPUT B : VIDEO-2
INPUT C : COMPO.
INPUT D : RGB
INPUT E : NO SLOT
INPUT F : NO SLOT
EXIT:
MENU
ITEM CONTENTS AND ADJUSTMENT RANGE/SETTINGS
16:94:3
14:9 13:9
LEVEL : 00
CONTROL FREQ. :HIGH
sub menu
reset
EXIT:
MENU ADJUST:- + SELECT:
Items : INPUT A:/INPUT B:/INPUT C:/INPUT D:/INPUT
E:/INPUT F:
Settings : VIDEO-1/VIDEO-2/COMPO./RGB/SDI 1/SDI 2/
HD SDI 1/HD SDI 2/HD SDI 1
*/HD SDI 2*/NO
SLOT
Function : Displays the status of the input cards installed in
each of the input card slots.HD SDI 1 or HD SDI 2 shows the HD SDI input card is
installed.
HD SDI 1
* and HD SDI 2* show the HD SDI input card
(compatible with EMBEDDED AUDIO) is installed.
●NO SLOT shows no input cards are installed.
3. sub menu POSITION
Items : Selects the display position of the sub menu
superimposed on the screen.
Settings : UPPER/LOWER
Functions : UPPER : An adjustment item is displayed on the
top of the screen.
LOWER : An adjustment item is displayed on the
bottom of the screen.
4. AREA MARKER
Items : Selects the size marker for the other screen ratio
(aspect) used when the screen ratio is 16:9.
Settings : OFF/16:9/4:3/13:9/14:9/MODE 1/MODE 2
Functions : OFF: The marker is not displayed.
16:9/4:3/13:9/14:9: Displays the marker (a white
quadrangle) showing the screen size of each
aspect ratio.
MODE 1/MODE 2: Displays no markers because
these settings will be used for function expansion
in the future.
●AREA MARKER is displayed when the displayed picture is
such a format as 1080i/1035i/720p etc. or has been
converted to 16:9 ratio by pressing the ASPECT button.
●To actually display the marker, the AREA MARKER button
on the monitor needs to be pressed so that it is
illuminated.
HOW TO USE “MAIN MENU” (contd)
LCT1261-001A (EN)02.6.25, 12:25 PM 14
ENGLISH
13
Input Signal Format Standard Manual
setting setting
(MANUAL)
NTSC, PAL, 480/60i,
ITU601
480/60p, 576/50i, 575/50p
ITU709
720/60p, 1080/50i, 1080/60i,
ITU709
1035/60i, 1080/24psF
SELECT :MANUAL
R-Y PHASE : 90
R/B GAIN :0.86
G-Y PHASE : 244
G/B GAIN :0.36
sub menu
reset
EXIT:
MENU ADJUST:- + SELECT:
5. AREA MARKER-R
Items : Selects the size marker for the other screen ratio
(aspect) used when the screen ratio is 16:9. (for
external control)
Settings : OFF/16:9/4:3/13:9/14:9/MODE 1/MODE 2
Functions : OFF: The marker is not displayed.
16:9/4:3/13:9/14:9: Displays the marker (a white
quadrangle) showing the screen size of each
aspect ratio.
MODE 1/MODE 2: Displays no markers because
these settings will be used for function expansion
in the future.
●AREA MARKER-R is displayed when the displayed picture
is such a format as 1080i/1035i/720p etc. or has been
converted to 16:9 ratio by pressing the ASPECT button.
●The marker is actually displayed when the external control
selects each setting. (No markers are displayed even if
each marker is selected only in the monitor’s AREA
MARKER-R setting.)
6. CENTER MARKER
Items : Makes the centre marker appear or disappear.
Settings : ON/OFF
Functions : ON : The centre marker (a white cross) is
displayed on the centre of the screen.
OFF : The marker disappears.
●To actually display the marker, the AREA MARKER
button on the monitor needs to be pressed so that it is
illuminated.
Centre marker
7. COLOR MATRIX
Selects or adjusts the
standard of the colour
demodulation (colour
rendering). Press the
button to display the setting
menu illustrated on the right.
The menu screen when
MANUAL is selected.
●The standard setting is set to “ITU601” or “ITU709”
depending on the input signal format.
The factory preset of MANUAL is ITU709
Item : SELECT
Function : Selects the picture matrix standard.
Settings : ITU601 or ITU709/ MANUAL
ITU601 or ITU709 : Standard setting
MANUAL : Manual setting
NOTE :The following items are displayed when MANUAL is
selected. When ITU601 or ITU709 is selected, they
are not displayed.
Item : R-Y PHASE
Function : Sets the R-Y phase.
Settings : 90/92/94/112
Item : R/B GAIN
Function : Sets the R/B gain.
Settings : 0.86/0.56/0.68/0.79
Item : G-Y PHASE
Function : Sets the G-Y phase.
Settings : 244/253/236/240
Item : G/B GAIN
Function : Sets the G/B gain.
Settings : 0.30/0.34/0.40/0.45
Item : sub menu
Function : Performs the R-Y PHASE, R/B GAIN, G-Y
PHASE or G/B GAIN settings in a single-line
display. The display position depends on the
“sub menu POSITION” setting.
Settings : Same as R-Y PHASE, R/B GAIN, G-Y PHASE or
G/B GAIN
Item : reset
Function : Sets the R-Y PHASE, R/B GAIN, G-Y PHASE
and G/B GAIN values to factory-preset ones.
R-Y PHASE 90
ITU601R/B GAIN 0.79G-Y PHASE 244
G/B GAIN 0.45
R-Y PHASE 90
ITU709R/B GAIN 0.86G-Y PHASE 244
G/B GAIN 0.30
LCT1261-001A (EN)02.6.25, 12:25 PM 15
HOW TO USE “SETUP MENU”
“SETUP MENU” ITEMS
Items Functions
1 FUNCTION SETTING Displays the monitor’s power-up time or the total usage time.
2 PICTURE SUB ADJ. Performs approximate adjustments using the control knobs on the front panel.
3 COLOR TEMP./BAL. Sets or adjusts the colour temperature or white balance.
4 SIZE/POSI. ADJ. Adjusts the size or position of the picture.
5 DISTORTION ADJ. Compensates the picture distortion.
6 STATUS DISPLAY Makes the status of the input signal appear or disappear on the screen.
7 CONTROL LOCK Sets the control lock preventing the monitor from misuse.
8 all reset Sets all items in SETUP MENU to factory-preset values.
“SETUP MENU” SCREENS
FUNCTION SETTING
PICTURE SUB ADJ.
COLOR TEMP./BAL.
SIZE/POSI.ADJ.
DISTORTION ADJ.
STATUS DISPLAY
CONTROL LOCK :ON
all reset
EXIT:
MENU ENTER:+ SELECT:
COLOR SYSTEM :AUTO
SYNC SELECT :INT.
RUSH DELAY TIME :STD.
TALLY SELECT :GREEN
REMOTE SYSTEM :MAKE
EMBEDDED :1G
HOUR METER X100h :000
EXIT:
MENU ADJUST:- + SELECT:
CONTRAST : 00
BRIGHT : 00
CHROMA : 00
PHASE : 00
NTSC SETUP : 00
COMPO.LEVEL :SMPTE
sub menu
reset
EXIT:
MENU ADJUST:- + SELECT:
COLOR TEMP. :LOW
BLUE DRIVE : 000
RED DRIVE : 000
GREEN CUTOFF : 000
BLUE CUTOFF : 000
RED CUTOFF : 000
sub menu
reset
EXIT:
MENU ADJUST:- + SELECT:
H.SIZE : 00
H.POSITION : 00
V.SIZE : 00
V.POSITION : 00
sub menu
reset
EXIT:
MENU ADJUST:- + SELECT:
PINCUSHION : 00
PIN.BALANCE : 00
PARALLELOGRAM : 00
TRAPEZOID : 00
ROTATION : 00
sub menu
reset
EXIT:
MENU ADJUST:- + SELECT:
STATUS DISPLAY :ON
1080/1035 :1080
EXIT:
MENU ADJUST:- + SELECT:
CONTRAST : 00
- - + +
BLUE DRIVE :000
- - + +
H.SIZE : 00
- - + +
PINCUSHION : 00
- - + +
Aer you sure ?
"Yes" then + Key.
"No" then MENU Key.
54
LCT1261-001A (EN)02.6.25, 12:25 PM 16
ENGLISH
15
COLOR SYSTEM :AUTO
SYNC SELECT :INT.
RUSH DELAY TIME :STD.
TALLY SELECT :GREEN
REMOTE SYSTEM :MAKE
EMBEDDED :1G
HOUR METER X100h :000
EXIT:
MENU ADJUST:- + SELECT:
ITEM CONTENTS AND ADJUSTMENT RANGE/SETTINGS
1. FUNCTION SETTING
Selects the colour system and
displays the monitor’s power-
up time or the total usage time.
Press the
button to display
the setting menu illustrated on
the right.
Item : COLOR SYSTEM
Settings : AUTO/NTSC/PAL
Function : Selects the colour system when using the video
input card.
AUTO : Change NTSC and PAL automatically.
NTSC : Keeps the colour system NTSC.
PAL : Keeps the colour system PAL.
NOTE :Normally select AUTO. However, if the input signal is
unstable, select NTSC or PAL.
Item : SYNC SELECT
Settings : INT./EXT.
Function : Synchronised signal selection.
INT. : The input video signal is synchronised
with the built-in sync signal.
EXT. : The input video signal is synchronised
with an external signal from an external
sync terminal.
* The external synchronised signal terminals apply to the HD/
CS terminal and VD terminal (in the RGB/COMPONENT Input
Card), or the EXT. SYNC terminal (in the VIDEO Input Card).
* This item is not shown when only SDI and/or HD SDI input
cards are installed.
Item : RUSH DELAY TIME
Settings : STD./SLOW
Function : Sets the time when the power supply to the
monitor’s circuits (excluding the micro computers)
starts after the power switch is pressed.
STD. :The power supply starts approx.
1 second after the power switch is
pressed.
SLOW : The power supply starts approx.
3.2 seconds after the power switch is
pressed.
NOTE :If you are going to turn several Multi-Format Monitors
on at the same time, it is recommended to apply
SLOW to some of the monitors to control rush current.
Item : TALLY SELECT
Settings : GREEN/RED
Function : Selects the colour of the tally lamp (when lit) on
the upper front panel.
GREEN : The tally lamp lights in green.
RED : The tally lamp lights in red.
NOTE :Set the MAKE/TRIGGER terminal’s tally control in the
REMOTE (external control) terminal setup menu. For
details, refer to Page 19. To set the color, use TALLY
SELECT in the “FUNCTION SETTING” setup menu or
MAKE/TRIGGER in the REMOTE (external control)
terminal setup menu. For details, refer to Page 15 and 19.
Item : REMOTE SYSTEM
Settings : MAKE/TRIGGER
Function : Selects the contact system (MAKE (make
contact) or TRG. (trigger contact)) for the MAKE/
TRIGGER terminals.
MAKE (make contact system): Controls the
function by stable disconnection (terminal
open) or short-circuit (short with GND of 15th
terminal) of the controlled terminal.
TRG. (trigger system): Controls the function by
instantaneously (one second) short-circuiting
(short with GND of 15th terminal) the controlled
terminal.
Item : EMBEDDED
Settings : 1G/2G/1-2G
1G :
2G :
1-2G :
Function : Selects Embedded Audio signal channels.
NOTE :The auto setting mixes and outputs all 8 signal channels.
Output level is automatically detected and set at FPGA
according to the channel numbers that are receiving signals.
* About sound output level
Sound output level is set to a standard output level for all
channels when several sound channels are output at the
same time. The more channels are selected, the lower each
channel’s level will be.
(Each channels level becomes half for 1– 2 channel, 1/4 for
1– 4 channel.)
*About AUTO
When AUTO is selected, the number of sound channels in use
is detected. The level of each channel is automatically
adjusted to ensure that the total sound output level is equiva-
lent to the standard output level.
* This item is shown when an input card compliant with EM-
BEDDED AUDIO is installed.
Item : HOUR METER X100h
Number
range : 000 ~ 655
Function : Displays the total usage time of the monitor in
hundred-hour units.
CONTRAST : 00
BRIGHT : 00
CHROMA : 00
PHASE : 00
NTSC SETUP : 00
COMPO.LEVEL :SMPTE
sub menu
reset
EXIT:
MENU ADJUST:- + SELECT:
●When the timer passes 655, it returns to 000.
●The timer does not count the usage time under one hour.
2. PICTURE SUB ADJ.
Performs approximate
adjustments using the control
knobs on the front panel. Press
the
button to display the
setting menu illustrated on the
right.
NOTE :When the RGB signal
is input, only
CONTRAST and
BRIGHT are displayed. When the PAL signal is
input, only CONTRAST, BRIGHT and CHROMA are
displayed.
1ch 2ch 3ch 4ch 1-2ch 3-4ch 1-4ch
5ch 6ch 7ch 8ch 5-6ch 7-8ch 5-8ch
AUTO 5-8ch 1-4ch 7-8ch 5-6ch 3-4ch 1ch 2ch 3ch 4ch 5ch 6ch 7ch 8ch 1-2ch
LCT1261-001A (EN)02.6.25, 12:25 PM 17
Item : CONTRAST
Adjustment
range : –20 ~ 00 ~ +20
Function : For approximate adjustment of the picture
contrast. Before adjustment, turn the CON-
TRAST knob on the front panel to the middle.
Item : BRIGHT
Adjustment
range : –20 ~ 00 ~ +20
Function : For approximate adjustment of the picture
brightness. Before adjustment, turn the BRIGHT
knob on the front panel to the middle.
Item : CHROMA
Adjustment
range : –20 ~ 00 ~ +20
Function : For approximate adjustment of the colour
density. Before adjustment, turn the CHROMA
knob on the front panel to the middle.
Item : PHASE
Adjustment
range : –20 ~ 00 ~ +20
Function : For approximate adjustment of the picture hue.
Before adjustment, turn the PHASE knob on the
front panel to the middle.
Item : NTSC SETUP
Settings : 00/7.5
Function : Sets the level of the input NTSC signal.
00 : Compliant with 0% set-up signal.
75 : Compliant with 7.5% set-up signal.
NOTE :NTSC SETUP is displayed only when the video input
card is installed and an NTSC signal is input.
Item : COMPO. LEVEL
Settings : SMPTE/B75/B00
Function : Sets the level of the input component signal.
SMPTE : Compliant with M2VTR signals.
B75 : Compliant with Betacam 7.5% set-up
signal.
B00 : Compliant with Betacam 0% set-up
signal.
NOTE :COMPO. LEVEL is displayed only when a 480/60i,
480/60p, 576/50i or 576/50p signal is input.
Item : sub menu
Adjustment range/
Settings : Same as CONTRAST, BRIGHT, CHROMA,
PHASE and COMPO LEVEL/NTSC SETUP.
Function : Performs CONTRAST, BRIGHT, CHROMA,
PHASE or COMPO LEVEL/NTSC SETUP
settings in a single-line display. The sub menu
display varies depending on the selected item.
Item : reset
Function : Sets the CONTRAST, BRIGHT, CHROMA,
PHASE and COMPO LEVEL/NTSC SETUP
values to factory-preset ones.
COLOR TEMP. :LOW
BLUE DRIVE : 000
RED DRIVE : 000
GREEN CUTOFF : 000
BLUE CUTOFF : 000
RED CUTOFF : 000
sub menu
reset
EXIT:
MENU ADJUST:- + SELECT:
3. COLOR TEMP./BAL.
Sets or adjusts the colour
temperature or white balance.
Press the
button to display
the setting menu illustrated on
the right.
Item : COLOR TEMP.
Settings : HIGH/LOW
Function : Selects the colour temperature.
HIGH : Sets the colour temperature to D93.
LOW : Sets the colour temperature to D65.
Item : BLUE DRIVE
Adjustment
range : MIN ~ 000 ~ MAX (in 127 grades)
Function : Adjusts the blue drive level.
Item : RED DRIVE
Adjustment
range : MIN ~ 000 ~ MAX (in 127 grades)
Function : Adjusts the red drive level.
Item : GREEN CUTOFF
Adjustment
range : MIN ~ 000 ~ MAX (in 255 grades)
Function : Sets the green cut-off point.
Item : BLUE CUTOFF
Adjustment
range : MIN ~ 000 ~ MAX (in 255 grades)
Function : Sets the blue cut-off point.
Item : RED CUTOFF
Adjustment
range : MIN ~ 000 ~ MAX (in 255 grades)
Function : Sets the red cut-off point.
Item : sub menu
Adjustment range/
Settings : Same as BLUE DRIVE, RED DRIVE, GREEN
CUTOFF, BLUE CUTOFF and RED CUTOFF.
Function : Performs BLUE DRIVE, RED DRIVE, GREEN
CUTOFF, BLUE CUTOFF or RED CUTOFF
settings in a single-line display. The sub menu
display varies depending on the selected item.
Item : reset
Function : Sets the BLUE DRIVE, RED DRIVE, GREEN
CUTOFF, BLUE CUTOFF and RED CUTOFF
values to factory-preset ones.
16
HOW TO USE “SETUP MENU” (contd)
LCT1261-001A (EN)02.6.25, 12:25 PM 18
ENGLISH
17
PINCUSHION : 00
PIN.BALANCE : 00
PARALLELOGRAM : 00
TRAPEZOID : 00
ROTATION : 00
sub menu
reset
EXIT:
MENU ADJUST:- + SELECT:
31sDISTORTIONsADJ1
Compensates the picture
distortion. Press the
button
to display the setting menu
illustrated on the right.
Item : PINCUSHION
Adjustment
range : –20 ~ 00 ~ +20
Function : Compensates pincushion picture distortion.
– : Expands both left and right sides of the
picture.
+ : Squeezes both left and right sides of the
picture.
Item : PIN.BALANCE
Adjustment
range : –20 ~ 00 ~ +20
Function : Adjusts the compensation balance of the
pincushion picture distortion.
– : The picture is expanded on the left side, and
squeezed on the right side.
+ : The picture is squeezed on the left side, and
expanded on the right side.
Item : PARALLELOGRAM
Adjustment
range : –20 ~ 00 ~ +20
Function : Compensates parallelogram picture
distortion.
– : Moves the upper side of the picture to the
right, and the lower side to the left.
+ : Moves the upper side of the picture to the left,
and the lower side to the right.
Item : TRAPEZOID
Adjustment
range : –20 ~ 00 ~ +20
Function : Compensates trapezoid picture distortion.
– : Enlarges the upper side of the picture.
+ : Reduces the upper side of the picture.
Item : ROTATION
Adjustment
range : –31 ~ 00 ~ +31
Function : Compensates for picture tilt.
– : Turns the picture clockwise.
+ : Turns the picture counterclockwise.
Item : sub menu
Adjustment range/
Settings : Same as PINCUSHION, PIN.BALANCE, PARAL-
LELOGRAM, TRAPEZOID and ROTATION.
Function : Performs PINCUSHION, PIN.BALANCE,
PARALLELOGRAM, TRAPEZOID or ROTATION
settings in a single-line display. The sub menu
display varies depending on the selected item.
Item : reset
Function :Sets the PINCUSHION, PIN.BALANCE,
PARALLELOGRAM, TRAPEZOID and ROTATION
values to factory-preset ones.
H.SIZE : 00
H.POSITION : 00
V.SIZE : 00
V.POSITION : 00
sub menu
reset
EXIT:
MENU ADJUST:- + SELECT:
Item " H1SIZE
Adjustment
srange "
STATUS DISPLAY :ON 1080/1035 :1080 EXIT: MENU ADJUST:- + SELECT: Item : STATUS DISPLAY Settings : ON/OFF Function : Makes the format name appear or disappear when signals are input and the signal status appear or disappear when the input signal is changed. ON : The information is displayed. OFF : The information is not displayed. Item : 1080/1035 Settings : 1080/1035 Function : Makes the number of effective scanning lines appear or disappear when the HDTV signal is input. 1080 : Sets the number to 1080. (Select when the digital HDTV signal is input.) 1035 : Sets the number to 1035. (Select when the analog HDTV signal is input.) 7. CONTROL LOCK Item : CONTROL LOCK Settings : OFF/ON Function : Invalidates most of operations on the front panel (including menu screen operations). OFF : Enables normal operations. ON : Invalidates all operations except the power switch and CONTROL LOCK. NOTE:While CONTROL LOCK is set to ON, attempting to perform any operation except power switch and CONTROL LOCK causes the “ Control lock on!” warning to appear on the screen for approx. 3 seconds. (It is possible to operate the power switch and display SETUP MENU.) When SETUP MENU is displayed while CONTROL LOCK is set to ON, the cursor ( 4) is located next to CONTROL LOCK and cannot be moved. 8. all reset Function : Sets all items in SETUP MENU to factory-preset values. 6. STATUS DISPLAY Makes the status of the input signal appear or disappear on the screen. Press the button to display the setting menu illustrated on the right. 18 HOW TO USE “SETUP MENU” (contd) LCT1261-001A (EN)02.6.25, 12:25 PM 20