Panasonic Monitor Bt Lh1700w Owners Manual

Operating Instructions
LCD Video Monitor
Model BT- P
S0805M1095 -H
Printed in Japan
VQT0U69-1ENGLISHD
Before operating this product, please read the instructions carefully and save this manual for future use.  

2
indicates safety information.
gTHIS EQUIPMENT MUST BE GROUNDED
To ensure safe operation, the three-pin plug must 
be inserted only into a standard three-pin power 
outlet which is effectively grounded through 
normal household wiring. Extension cords used 
with the equipment must have three cores and be 
correctly wired to provide connection to the 
ground. Wrongly wired extension cords are a 
major cause of fatalities. The fact that the 
equipment operates satisfactorily does not imply 
that the power...

3
FCC NOTICE (USA)
IMPORTANT SAFETY INSTRUCTIONS
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus  
(including amplifiers) that produce heat.
9) Do not defeat the safety purpose...

4
The liquid crystal portion is manufactured with highly precise technology. It includes over 99.99% effective pixels, 
but 0.01% or less of the pixels are either missing, or have fixed lighting (red, blue, green). This is not a sign of 
malfunction. 
The liquid crystal protection panel is a specially manufactured component. Wiping it with a hard cloth, or rubbing 
it vigorously will scratch the surface. 
If a still image is displayed for a long time, it may cause temporary generation of afterimage...

5
The BT-LH1700W liquid crystal monitor was designed especially for broadcasting service and business use. It is
equipped with a high performance 17.1-inch wide liquid crystal display panel. 
gHigh performance liquid crystal panel
This monitor achieves outstanding color reproducti on, a wide viewing angle, and high-speed response. 
g Immediate image output of input signals 
The time-lag caused by IP field unit conversion
*1 has been eliminated, and the delay from input until image 
output has been...

6
Video monitor unit
Front view
Rear view
Rear panel (J page 8) An embedded audio unit (BT-YAE1700G) can be 
attached (J Installation Guide included). 
Power supply [you can switch 
between AC and DC (J page 9)] Front panel (J page 7)
Fan
Controls and Their Functions 

7
POWER switch
This switches the power supply ON/OFF. When the power is ON, the LED (green) lights up. 
INPUT SELECT button
This selects the signal input line. The green LED light above the button indicates the selected input signal. 
VIDEO : Video input
Y/C : Y/C input
SDI1 : Serial digital interface input (HD/SD compatible) 
SDI2 : Serial digital interface input (HD/SD compatible) 
YP
BPR/RGB : Analog component (YPBPR) or RGB input. Also compatible with PC input RGB. 
* When using PC Input, select...

8
SDI (HD/SD) terminal (BNC)
IN1  : This is the SDI input terminal (compatible with HD/SD automatic switching). 
IN2  : This is the SDI input terminal (compatible with HD/SD automatic switching). 
SWITCHED OUT: This is the active through-out terminal for the SDI input signal being displayed on the screen. 
* SDI active through-out is only outputted when [SDI1] or [SDI2] is selected using the [INPUT SELECT] 
buttons. It is not outputted when anything other than SDI is selected. 
VIDEO terminal (BNC)
IN :...

9
1. Attach the power cord to the monitor unit. 
2. Connect the power cord to the power outlet. gWhen using external DC power (DC11V–17V)
You can slide open the power cover, and switch from 
AC input to external DC input. (When shipped from 
the factory, the power cover is up, and AC input is 
selected.)
Please note the following
If the power cover has been removed or opened, do not 
use the monitor with the power supply connected to 
both the AC input and external DC input terminals. 
 
Connecting and...

10
Three types of information are displayed on the screen. The input signal status, picture adjusting knob status, and 
the menu display. 
1. The selected input line (J page 7,  )
VIDEO, Y/C, SDI1, SDI2,  
YP
BPR/RGB-VIDEO/RGB-COMP.
2. Signal format
The display status can be set in “STATUS 
DISPLAY” in the “SYSTEM CONFIG” menu 
(J page 18). 
If “UNSUPPORT SIGNAL” is displayed, then either 
the current input signal is not supported or the 
“INPUT SELECT” menu setting needs to be 
changed. 
When “NO...