Panasonic Monitor Bt Lh1760p Owners Manual

21
■ WB adjustment mode
Select “VAR1” to “VAR3” for “COLOR TEMP.” in the “VIDEO CONFIG” menu to make “WHITE BALANCE VAR1”
to “WHITE BALANCE VAR3” (WB) adjustments. 
Underlined values indicate factory defaults.
*1 Selecting “COLOR TEMP.” and pressing [ENTER] after making a change, opens a confirmation screen.
Selecting “YES” and pressing [ENTER] in this screen resets selected GAIN and BIAS values to the selected
color temperature values. 
*2 The item display moves to the lower part of the screen during...

22
Main Menu (continued)
Underlined values indicate factory defaults.
*1 When the monitor is shipped, settings for “USER1” - “USER5” are identical to “FACTORY.” 
*2 “H-POSITION”, “V-POSITION”, “PHASE” and “CLOCK” (Jpage 31) cannot be saved or loaded.
*3 Double speed reduces image lag caused by black signal input but lowers resolution compared to standard
speed and some images may generate flicker. Return to standard speed should flicker become noticeable. 
*4 ITU-709 is an ITU-R BT.709 standard.
*5...

23
Underlined values indicate factory defaults.
*1 Changes in settings change menu settings. 
FUNCTION
Sub menu Settings Description
FUNCTION 1 - 
FUNCTION 5HV DELAY
AUTOS ETUP
BLUE ONLY
GAMMA SELECT
SD ASPECT
SCAN
SUB WINDOW
WFM/VECTOR
MARKER
PIXEL TO PIXEL
PIXEL POSITION
LEVEL METER
CROSS HATCH
MONO
TIME CODE
CLOSED 
 CAPTION
UNDEF
(Factory default: 
FUNCTION1:
 MARKER
FUNCTION2:
 WFM/VECTOR
FUNCTION3:
 PIXEL TO PIXEL
FUNCTION4:
 TIME CODE
FUNCTION5:
 LEVEL METER)Selects functions to be assigned to...

24
■FUNCTION setting restrictions
Settings are not available under the following conditions.
 
Setting Conditions that disable operation
HV DELAY
During SUB WINDOW, WFM, PIXEL TO PIXEL mode operation, “INVALID FUNCTION” 
appears to indicate that operation is disabled. 
When “RGB-COMP.” is selected under “YP
BPR/RGB” or “DVI-COMP.” is selected under 
“DVI-D” in the “INPUT SELECT” menu, “INVALID FUNCTION” appears to indicate that 
operation is disabled.
AUTO  S ETUP
When something other than “RGB-COMP.” is...

25
■Functions displayed during FUNCTION button operation
Pressing any of the [FUNCTION1] to [FUNCTION5] buttons displays the operations assigned to each button as
shown below. 

DELAY OFF/V DELAY/H DELAY/HV DELAY

AUTOSETUP/COMPLETE/INCOMPLETE/NOT 
RGB-COMP.CH

BLUE ONLY ON/BLUE ONLY OFF
 GAMMA SELECT
GAMMA STANDARD/GAMMA FILM/GAMMA 
STDIO/PST
 SD ASPECT
4:3/16:9
 SCAN
NORMAL SCAN/UNDER SCAN
 SUB WINDOW
SINGLE/FULL/PART/STILL

WFM ON/WFM/VECTOR OFF/VECTOR × 1/
VECTOR × 2/VECTOR × 4/VECTOR × 8 MARKER...

26
This function is designed to enable comparison of identical formats input to the same input terminal. Input of
different formats via different input channels may distort the sub-window (left side, still image) or blanking could
occur. However, input of an identical format signal to the input terminal during still image acquisition will display
correctly.
■“WFM/VECTOR” 
The “WFM/VECTOR” function enables display of the waveform and vector display. Use “DISPLAY SETUP” in the
main menu to select “WFM” and...

27
Main Menu (continued)
■“PIXEL TO PIXEL” and “PIXEL POSITION”
The “PIXEL TO PIXEL” function allows you to check images at their actual pixel resolution (1080I/P signals only). 
Press the button ([FUNCTION1] to [FUNCTION5] (Jpage 23)) to which the “PIXEL TO PIXEL” function has
been assigned to turn the function on. Then press the button ([FUNCTION1] to [FUNCTION5] (Jpage 23)) to
which the “PIXEL POSITION” function has been assigned to position the display of signals. (This assumes that
the “PIXEL TO...

28
Main Menu (continued)
■“CROSS HATCH”
The “CROSS HATCH” function enables display of markers at regular vertical and horizontal intervals to facilitate
composition and other tasks. The width of marker lines is 1 dot, the markers consist of 1 line, and are spaced 80
dots apart (fixed value).
Each press of the button (“FUNCTION1” to “FUNCTION5”) to which the “CROSS HATCH” has been assigned
turns the function on and off. 
Each press of the FUNCTION button to which the “CROSS HATCH” function is assigned...

29
“GPI CONTROL” is used to enable and disable GPI functions and assign functions to each of the GPI terminal pins
(J page 36). 
Underlined values indicate factory defaults.
Note: 
This function is not available when, 
“SD ASPECT” operation when input signal is HD or PC
“SCAN” operation when the input signal is PC
“GAMMA SELECT” operation when the input signal is PC
“SELECT SYNC” operation when anything other than “RGB-VIDEO” is selected under “YP
BPR/RGB” in the
“INPUT SELECT” menu
“MONO” operation when...

30
Underlined values indicate factory defaults.
*1 “AUTO” is the factory default, but select a specific format when there is risk that the input signal may be
contaminated by outside noise.
INPUT SELECT
Sub menu Settings Description
VIDEO
AU TO
NTSC
PA LSelects the video input format.
*1
 Automatically selects NTSC or PAL. 
 NTSC  PAL
NTSC SETUP
75
00
Selects NTSC setup level. 
 Select this function when using 7.5% setup signals. 
(Adjusts the interior of the monitor to the 7.5% setup 
level to suit the...