Panasonic Multi Format Live Switcher Av Hs400an Operating Instructions

21
2. System
 Connections when not implementing gen-lock 
(frame synchronizer ON)
• Example where the optional board is used
POWER
1 REF
GPI
SLOT2
2
SLOT
4
2 34
SLOT1
1
SLOT2 8
～IN
SDI  INPUTS
TALLY
6
6
INPUTS
SIGNALSDI  OUTPUTSGND
IN
OUT3
IN
OUT2
IN
OUT1
IN
OUT
OUTPUTS
15 7
SLOTOFF2
SLOT1 5
SLOT
SLOT
PGM RS-422
LAN ON
ANALOG INPUTS
Y Pb PrY Pb
Pr
DVI INPUTS
ANALOG OUTPUTS
Y Pb PrY Pb
Pr
DVI/ANALOG OUTPUTS
Y Pb PrDVI-IDVI-IDVI-I
VTR PC monitor
HD Component HD component monitor
HD SDI monitor...

22
3. Basic operations
3-1. Background transition
3-1-1. Selecting the bus
Press the crosspoint buttons to select the material which will be targeted for the background transition. 
By pressing these buttons, the signals are selected, and the indicators of the selected buttons light. 
The color in which the button indicators light differs depending on the operation status.Lighting in red: 
   When the selected input signals are output to PGM.
  (However, the indicator lights in amber during FTB...

23
3. Basic operations
3-1-3. Selecting the transition mode
Press the [BKGD] button in the transition area so that its indicator lights in amber. 
When the [BKGD] button and [KEY] button are pressed at the same time, both buttons are selected.
Use the [MIX] and [WIPE] buttons in the transition area to select the background transition mode. 
The indicator of the selected button lights in amber.
3-1-4. Manual transition (using the fader lever)
Operate the fader lever to execute transitions manually.
If the...

24
3. Basic operations
3-2. Wipe
3-2-1. Selecting the wipe pattern
BKGD PATTKEY PATT FUNC
WIPE PATTERN / FUNCTIONON WIPE SQ
SL 3D
PAGE
TIME WIPE COLOR
KEY CHR KEY FREEZE
DSK PinP IN/OUT
MEMORY XPT SYSTEM
1 2 3
4 5 6
7 8 9
101112
The wipe patterns which are allocated to the 12 wipe pattern buttons are used as the basis for wiping, and each 
button has four pages — wipe, squeeze, slide and 3D — of patterns. (Refer to the table of wipe patterns.)
Displayed for each wipe pattern selector button are an image...

25
3. Basic operations
3-2-2. Selecting the wipe direction
Operate the wipe direction selector buttons to select the wipe direction for the background transition. 
(The key transitions are set by the menu. The direction which is set here will not be reflected.   See 3-3-3.)When the [R] indicator is off:
 
  Wiping proceeds in the normal direction.
When the [R] indicator is lighted:
 
   Wiping proceeds in the reverse direction.
When the [N/R] indicator is lighted:
 
   The normal direction is replaced...

26
3. Basic operations
3-2-4. Setting the wipe start position
Any start position can be set for wipe pattern WIPE and SQ #5. 
The start position has one set of values for a background pattern and another set for a key pattern.
1 
 Press the [FUNC] button to light its indicator, and press the [WIPE] button to display the WIPE menu.
2 
  Turn [F1] to display the WIPEPos sub menu or the SQPos sub menu.
  
 
WIPEPosSelect X-Pos Y-Pos CopyTo↓
  3/5    BKGD    0.00    0.00     KEY
    KEY
−100.00
     |...

27
3. Basic operations
3-2-5.  Modifying wipe
   Setting the lighting effect
Lighting effects can be added when the following wipe patterns have been selected:
  3D page:

 #1, #3, #7, #9
1 
  Press the [FUNC] button to light its indicator, and press the [WIPE] button to display the WIPE menu.
2 
  Turn [F1] to display the Modify sub menu.
  
 
Modify Light-B Light-K Trim 4:3Auto
  5/5     Off     Off    16:9     Off      On
     On    4:3
4:3Smth
    Off     On
3  Turn [F2] to select whether the...

28
3. Basic operations
3-3. Key
This operation combines the background image with another image. The key definition can be adjusted, and an 
edge can be added to the combined image.
Also available as materials besides KEY for combining with the background image are PinP (picture in picture) 
and DSK (downstream key). The figure below shows their priorities.
KEY
PinP
DSK
Background image
How key combinations work is shown in the figure below.
HS400A
HS400ABackground
Key source
Key fill Output image 
Invert 

29
3. Basic operations
3-3-1. Selecting the key type
1  Press the [FUNC] button to light its indicator, and press the [KEY] button to display the KEY menu.
2 
  Turn [F1] to display the KEY sub menu.
3 
  Turn [F2] to select the Type item.
  
 
KEYType LumKey Fill PVW
  1/9  Linear ChrmOff     Bus    Auto
    Lum
 Chroma
   Full
 ChrmOn  Matte    Off
     On
 Lum (luminance key/self key):
      This is for creating the key signals from the luminance component or luminance and chroma component\
 
of the...

30
3. Basic operations
3-3-2. Selecting the key material
   Selecting the key fill and key source signals
Press the KEY button in the AUX bus selection area, and switch the selection of the key fill signal (indicator 
lights in amber) and key source signal (indicator lights in green).

With the indicator of the KEY button lighted in amber, press one of the AUX bus crosspoint buttons 1 to 10 to 
select the key fill signal.
The indicator of the selected crosspoint button lights in amber. (It will light in...