Home > Panasonic > Security Camera > Panasonic Network Camera WV-SF549 WV-SF548 WV-SF539 WV-SF538 Installation Guide

Panasonic Network Camera WV-SF549 WV-SF548 WV-SF539 WV-SF538 Installation Guide

Here you can view all the pages of manual Panasonic Network Camera WV-SF549 WV-SF548 WV-SF539 WV-SF538 Installation Guide. The Panasonic manuals for Security Camera are available online for free. You can easily download all the documents as PDF.

Page 11

11
[Precautions for use]
This product is designed to be used indoors. 
This product is not operable outdoors. 
This product has no power switch. 
When turning off the power, disconnect the 
power supply from the 12 V DC power supply 
or the PoE device. (When using both the 12 V 
DC power supply and the PoE device for power 
supply, disconnect both the connections.)
To keep on using with stable performance
Do not use this camera in hot and humid con-
ditions for a long time. 
Failure to observe this...

Page 12

12
Code label
The code labels (accessory) are required at 
inquiry for trouble. Use caution not to lose 
these labels. It is recommended to paste one 
of the labels onto the CD-ROM case. 
Discoloration on the color filter of the 
MOS image sensor
  •  When continuously shooting a bright light 
source such as a spotlight, the color filter 
of the MOS image sensor may have deteri-
orated and it may cause discoloration. 
Even when changing the fixed shooting 
direction after continuously shooting a...

Page 13

13
Precautions for Installation
Panasonic assumes no responsibility for injuries or property damage resulting from fail-
ures arising out of improper installation or operation inconsistent with this documentation.
This camera is designed to be used indoors. 
This product is not operable outdoors. 
Do not expose this camera to direct sunlight for 
hours and do not install the product near a heater 
or an air conditioner. Otherwise, it may cause 
deformation, discoloration and malfunction. Keep 
this...

Page 14

14
Screw tightening
  • The screws and bolts must be tightened 
with an appropriate tightening torque 
according to the material and strength of 
the installation area. 
  • Do not use an impact driver. Use of an 
impact driver may damage the screws or 
cause tightening excessively. 
  •  Tighten screws at a right angle to the sur-
face. After tightening screws, perform checks 
to ensure that the tightening is sufficient 
enough so that there is no movement or 
looseness.
Procure fixing screws...

Page 15

Major operating controls
  *  This connector is provided only for service. Do not use the connector for checking the adjust-
ment of the angular field of view on the video monitor. 
IMPORTANT:
  •  Do not hold the inner dome while working on the camera. The inner dome may come off of the 
camera. 
SF549 SF548
MarkerDirection marker for installation
Azimuth adjustment ring
Tilting table
Panning lock screw [LOCK]
Panning tableRPHFRYHU

Page 16

16

About the [INITIAL SET] button
After turning off the power of the camera, turn on the power of the camera while holding down this 
button, and wait for around 5 seconds or more without releasing this button. Wait around 2 minutes 
after releasing the button. The camera will start up and the settings including the network settings 
will be initialized. Do not turn off the power of the camera during the process of initialization. Before 
initializing the settings, it is recommended to write down the...

Page 17

17
Detaching the dome cover
z  Loosen the dome cover fixing screws using 
the bit for tamperproof screw (accessory).
Note:
  •  The dome cover and the camera are joint-
ed with an assist wire. Do not remove the 
assist wire. 
 
Detach the dome cover from the camera by loosening the dome cover fixing screws. 
SF549SF548
The following procedure is required when using WV-SF549 or WV-SF548. Refer to page 18 when 
using WV-SF539 or WV-SF538.
IMPORTANT:
  •  Remove the cover film from the dome section of the...

Page 18

18
z  Remove the dome cover fixing screw (M3, 
step screw, x1). 
x Rotate the dome cover counterclockwise 
two steps, and align the indication OPEN 
to the marker of the camera to detach the 
dome cover.
Note:
  • Before the camera is installed, the dome 
cover can be removed more easily when 
putting a finger over the opening on the 
bottom of the camera.
 
Detach the dome cover from the camera by removing the dome cover fixing screw. 
SF539SF539SF538SF538
The following procedure is required when using...

Page 19

19
Preparations
When installing the camera on a wall or a ceiling, there are four methods as specified below. 
(☞ Pages 20 and 21)
  •  Using the two-gang junction box
  •  Installing the camera directly on the ceiling or wall
  • Using the optional ceiling mount bracket WV-Q174 (for embedded installation on a ceiling)
SF539SF538
  •  Using the optional ceiling mount bracket WV-Q105*1 (for direct mounting on a ceiling) 
IMPORTANT:
  •  Procure 4 screws (M4) to secure the camera to a wall or a ceiling...

Page 20

20
Using the side cable access hole
When installing the camera directly on the ceiling or wall with cables exposed, cut out a portion of 
the dome cover to open a cable access hole.
The above procedure is also required when 
mounting the camera using the ceiling mount 
bracket WV-Q174 (option).
Method of camera installation
Using the two-gang junction box
Mount the camera on the two-gang junction box by fixing 4 screws (locally procured). (☞ Page 29)
   
Direction marker for installationTwo-gang junction...
Start reading Panasonic Network Camera WV-SF549 WV-SF548 WV-SF539 WV-SF538 Installation Guide

Related Manuals for Panasonic Network Camera WV-SF549 WV-SF548 WV-SF539 WV-SF538 Installation Guide

All Panasonic manuals