Panasonic Network Camera Wv Sfv611l Wv Sfv631l Installation Guide

							 
● The MONITOR OUT terminal output can be switched for NTSC or PAL monitors.
Installation Guide\
Network Camera
Model No.  WV-SFV631L/WV-SFV611L
WV-SFV631L
(This illustration\p represents \fV-S\bV631L)
PGQX1455YA Cs1213-1123  Printed in China 
●  
This manual describes the installation procedures, network camera installation, cable connec -
tions, and the angle of view adjustment.
●   Before reading this manual, be sure to read the Important Information.
●   This manual describes how to install the network camera using the WV -SFV631L model as an 
example.
Major operating controls
The component names of the camera are as follows. Refer to the illustration when installing or 
adjusting the camera.
Standard accessoriesMaking connections
Important Information  ...............................1 pc.
Installation Guide (this document)  ............ 1 set
Warranty card  ........................................... 1 setCD-ROM*1 
................................................. 1 pc.
Code label
*2  .............................................. 1 pc.
*1  The  CD-ROM  contains  the  operating  instructions  and  different  kinds  of  tool  software  pro -
grams.
*2   This  label  may  be  required  for  network  management.  The  network  administrator  shall  retain 
the code label.
The following parts are used during installation procedures.
A Base bracket ........................................ 1 pc.
C  Fixing screws for attachment plate 
   (M4 x 8 mm)  ...................................... 5 pcs.
(of them, 1 for spare)
G  Template B (for the base bracket)  .. 1 sheet.
I 2P power cable  .................................... 1 pc.
K Waterproof tape ................................... 1 pc.
B Attachment plate .................................. 1 pc.
D 4P alarm cable ..................................... 1 pc.
E MONITOR OUT conversion plug  ......... 1 pc.
F Template A (for the attachment plate) 1 sheet.
H Bit  ........................................................ 1 pc. 
J LAN cable cover .................................. 1 pc.
H K
●
 How to initialize the camera
Follow the steps below to initialize the network camera.
1  
Turn off the power of the camera. When using a PoE hub, disconnect the LAN cable from the cam-
era. When using an external power supply, disconnect the 2P power cable plug from the camera.
2    Turn on the power of the camera while holding down the INITIAL SET button, and then keep 
holding down the button for 5 seconds or more. About 2 minutes later, The camera will start 
up and the settings including the network settings will be initialized.
 
● When data is being sent via the network camera  Blinks green (accessing)Turn off each system’s power supply before making a connection. Before making connections, 
prepare the required peripheral devices and cables.
 
● When the camera is able to communicate with the connected device Lights orange
 
● When an SD memory card*
1 is inserted and could  Lights off → Blinks green →
be recognized  Lights off
 
● When data can be saved after the SD memory card is  Lights off → Lights green 
inserted and the SD ON/OFF button is pressed
 
● When data can be saved to the SD memory card  Lights green
 
● When the SD memory card is removed after holding down Lights green → Blinks green → Lights off
the SD ON/OFF button for about 2 seconds
 
● When data cannot be saved to the SD memory card because Lights off
an abnormality was detected or the SD memory card is 
configured not to be used
 
● When AF (Auto Focus) operation is being executed Blinks red (Interval of 1 time/ second)
 
● When the set is being started  Lights red
 
● When an SD memory card is recognized normally  Lights red → Lights off
 
●
When an abnormality is detected in both SD1 and SD2  Lights red
cards after the camera has started 
 
● When an abnormality is only detected in the SD1 card   Lights red → Blinks red 
after the camera has started  (Interval of 1 time/ 3 seconds)
 
● When an abnormality is only detected in the SD2 card  Lights red → Blinks red 
after the camera has started
 (Interval of 2 times/ 3 seconds)
IMPORTANT:
 
● When the camera is initialized, the settings including the network settings will be initial -
ized. Note that the CRT key (SSL encryption key) used for the HTTPS protocol will not 
be initialized.
 
● Before initializing the settings, it is recommended to write down the settings in advance.
 
● Do not turn off the power of the camera during the process of initialization. Otherwise, it 
may fail to initialize and may cause malfunction.
IMPORTANT:
 
● This is valid if the [Monitor out] is set to [Switch priority] ([Switch priority] is selected by 
default). For details, refer to the Operating Instructions (included in the CD-ROM).
IMPORTANT:
 
● Use all 4 pairs (8 pins) of the LAN cable (category 5 or better, straight, STP: For 
Europe).
 
● The maximum cable length is 100 m {328 feet}.
 
● Make sure that the PoE device in use is compliant with IEEE802.3af standard.
 
● When connecting both the 12 V DC power supply and the PoE device for power 
supply, 12 V DC will be used for power supply*.
* If a 12 V DC power supply and a PoE hub or router are used at the same time,  network connections may not be possible. In this case, disable the PoE settings.  
Refer to the operating instructions of the PoE hub or router in use.
 
● When the LAN cable is disconnected once, reconnect the cable after around 2 seconds. 
When the cable is quickly reconnected, the power may not be supplied from the PoE 
device.
 
● When cables are used outdoors, there is a chance that they may be af fected by 
lightning. In this case, install a lightning arrester just before where the cables con -
nect to the camera.
Connect a LAN cable (category 5 or better, straight, STP: For Europe)
Waterproof treatment for the cable joint sections
When connecting to a network using a PoE hub
Microphone/line input cable
Connect a monaural mini plug (ø3.5 mm).
 
● Input impedance: Approx. 2 kΩ (unbalanced)
 
● Recommended cable length: Less than 1 m {3.28 feet} (for microphone input)  
Less than 10 m {32.8 feet} (for line input)
 
● Recommended microphone: Plug-in power type (option)
 
● Supply voltage: 2.5 V ±0.5 V
 
● Recommended sensitivity of microphone: –48 dB ±3 dB (0 dB=1 V/Pa,1 kHz)
 
● Input level for the line input: Approx. –10 dBV
IMPORTANT:
 
● Be sure to use the 4P alarm cable provided with this product.
 
● Off, input, and output of the external I/O terminal 2 and 3 can be switched by configur -
ing the setting. Refer to the Operating Instructions on the provided CD-ROM for fur -
ther information about the EXT I/O terminal 2 and 3 (ALARM IN2, 3) settings (“Off”, 
“Alarm input”, “Alarm output” or “AUX output”).
 
● When using the EXT I/O terminals as the output terminals, ensure they do not cause 
signal collision with external signals.
 
● Install external devices so that they do not exceed the ratings above.
Connect the alarm input/output cable

• ALARM IN1(DAY/NIGHT IN), ALARM IN2, ALARM IN3Input specification:  No-voltage make contact input (4 V - 5 V DC, internally pulled up)
OFF:  Open or 4 V - 5 V DC
ON:  Make contact with GND (required drive current: 1 mA or more)
• ALARM OUT, AUX OUT Output specification:  Open collector output (maximum applied voltage: 20 V DC)
Open:  4 V - 5 V DC by internal pull-up
Close:  Output voltage 1 V DC or less (maximum drive current: 50 mA)
* The default of EXT I/O terminals is “Off”.
Connect an external amplifier-embedded speaker to the audio output cable
Connect a stereo mini plug (ø3.5 mm) (Audio output is monaural.).*
 
● Output impedance: Approx. 600 Ω (unbalanced)
 
● Recommended cable length: Less than 10 m {32.8 feet}
 
● Output level: –20 dBV
IMPORTANT:
 
● Connect/disconnect the audio cables and turn on the power of the camera after turn -
ing off the power of the audio output devices. Otherwise, loud noise may be heard 
from the speaker.
 
● Make sure that the stereo mini plug is connected to this cable. When a monaural mini 
plug is connected, audio may not be heard.  
When connecting a monaural speaker with amplifier, use a locally procured  conver-
sion cable (mono-stereo).
Adequate waterproof treatment is required for the cables when installing the camera with cables 
exposed or installing it under the eaves. The camera body is waterproof, but the cable ends are 
not waterproof.
Be sure to use the supplied waterproof tape at the points where the cables are connected to ap
-
ply waterproof treatment in the following procedure. Failure to observe this or use of a tape other 
than the provided waterproof tape (such as a vinyl tape) may cause water leakage resulting in 
malfunction. Before starting the installation, check the entire system configuration. 
The following illustration 
gives a wiring example of how to connect the camera to the network via a PoE device (hub).
 < Alarm input/output cable, power cable, micro -
phone/line input cable, audio output cable>
Wind the tape in a
half-overlapping m\.anner.
Wind the tape in a
half-overlapping 
manner .
Wind the tape in a
half-overlapping m\.anner.
Wind the tape in a
half-overlapping 
manner.
IMPORTANT :
How to wind the supplied waterproof tape
 
● Also waterproof the 2P power cable (accessory), 4P 
alarm cable (accessory), and external connections in 
the same way.
 
● Stretch the tape by approx. twice (see the illustration) 
and wind it around the cable. Insufficient tape stretch 
causes insufficient waterproofing.
 
● To prevent the LAN cable hook from coming loose 
easily, fit the  J
 LAN cable cover onto the pigtail 
cable as illustrated, and then slide it in the direction 
indicated by the arrow. 
The connector of the LAN cable used with this cam -
era must meet the following restrictions.  
Height when inserted (From bottom to hook.):   
Max. 16 mm {5/8 inches} 
Connector width: Max. 14 mm {9/16 inches}
 
● To install this product outdoors, be sure to waterproof 
the cables. Waterproof grade (IEC IP66 or equiva -
lent) is applied to this product only when it is installed 
correctly as described in these operating instructions 
and appropriate waterproof treatment is applied. The 
internal parts of base brackets are not waterproofed.
2x
Str etch the tape to 
about twice.
PoE device (hub)
PCLAN cable 
(category 5 or 
better, \ftraight, 
S\bP: For Europe)
Adju\ftment monitor
LAN cable
(category 5 or bet\,ter,
\ftraight, S\bP: For Eu\,rope)
LAN cable
(category 5 or bet\,ter, 
\ftraight, S\bP: For Eu\,rope)
Powered \fpeakerMicrophone
Powered \fpeaker
Microphone
Adjustment monitor\b
Recommended total \b
extended cable len\f\bth*
W\b-SF\b631L
W\b-SF\b631 L
IMPORTANT:
 
● The adjustment monitor is used for checking the adjustment of the angular field of view 
when installing the camera or when servicing. It is not provided for recording/monitoring use.
 
● Depending on the monitor, some characters (camera title, preset ID, etc.) may not be 
displayed on the screen.
 
● Use a switching hub or a router which is compliant with 10BASE-T/100BASE-TX.
 
● If a PoE hub is not used, each network camera must be connected to a 12 V DC 
power supply.
 
● When using 12 V DC, power supply from a PoE hub or router is not required.
INITIAL SET button
Dehumidifying 
device
Auto focus (A\b) butt\pon
SD slot 1 (SD1)
SD slot 2 (SD2)
SD ON/O\b\b button
• \bRONT must posi-
tioned in front of the 
camera (on the 
Panasonic logo sid\pe).
Direction marker 
for installation 
(\bRONT
)
Data Matrix: To our 
website
*2
Direction marker for i\pnstallation (TOP)
●  Points up when inst\palling to a wall.
Dome cover
Light-blocking rubber ring IR LED
Azimuth adjustment ring Tilting tablePanning table
Camera fixing screw
The hook engages 
with the connector\p 
terminal
J 
LAN cable cover
C
 Fixing screws for 
attachment plate 
(accessory)
Enclosure
(Screw size 6.35 mm  
{1/4 inches} torx wrench)
Camera B
   Attachment 
plate (accessory) A
  Base bracket 
(accessory)
ACT indicator
LINK indicator
SD MOUNT indicator
SD ERROR/A\b indicat\por
*1 SDXC/SDHC/SD memory card is described as SD memory card.
*2    
Depending on the scanning application used, the Data Matrix may not be able to be 
read correctly. In this case, access the site by directly entering the following URL.
    http://security.panasonic.com/pss/security/support/qr_sp_select.html
MONITOR OUT termin\pal 
(factory shipment: N\pTSC 
monitor)
D  4P alarm cable (a\kccessory)
GND (black)
\fL\fRM \bN3, \fUX OUT (g\kray) (Terminal 3)
\fL\fRM \bN2, \fL\fRM OUT (r\ked) (Terminal 2)
\fL\fRM \bN1, D\fY/N\bGHT \b\kN (green) (Terminal\k 1)
Connect the output cable of the AC adaptor to the 2P power cable.
Power cable
 
12 V DC
Red  Positive
Black  Negative
WV-SFV631L

LAN cable (category 5 or better, straight, STP: For Europe)
Use a LAN cable (category 5 or better, cross) when directly connecting the camera to a PC.
* Recommended cable length from the speaker: less than 10 m {32.8 feet}
Recommended cable length from the microphone: less than 1 m {3.28 feet}
For U.S. and Canad\Pa:
Pana\fonic Sy\ftem Comm\P\bnication\f 
Company of North Am\Perica,
Unit of Pana\fonic Co\Prporation
of North America
www.panasonic.com/busi\pness/
\bor customer support\p, call 1.800.528.6\p747
Two Riverfront Plaza, Newark,\p NJ 07102-5490
Pana\fonic Canada Inc\P.5770 Ambler Drive,\p Mississauga,
Ontario, L4\f 2T3 Ca\pnada 
(905)624-5010
www.panasonic.ca For E\brope and other co\bnt\Prie\f:
009100A200AF00A200B400B000AF00AA00A40061008400B000B300B100B000B300A200B500AA00B000AF
http://panasonic.ne\pt
Panasonic System Ne\ptworks Co., Ltd.  
\bukuoka, Japan
Authorised Representative in EU:
Panasonic Testing Centre
Panasonic Marketin\pg Europe GmbH
\finsbergring 15, 22525 Ha\pmburg, Germany
* Use an external powered 
speaker.
Connect the power cable
IMPORTANT: 
● The 12 V DC power supply shall be insulated from the commercial  AC power.
 
● Be sure to use the 2P power cable provided with this product.
 
● Be sure to fully insert the 2P power cable into the 12 V DC power supply terminal. 
Otherwise, it may damage the camera or cause malfunction.
 
● When installing the camera, make sure that excessive force is not applied to the 
power cable.
Caution: 
● A READILY ACCESSIBLE DISCONNECT DEVICE SHALL 
BE INCORPORATED TO THE EQUIPMENT POWERED 
BY 12 V DC POWER SUPPLY.
 
● ONLY CONNECT 12 V DC CLASS 2 POWER SUPPLY (UL 
1310/CSA 223) or LIMITED POWER SOURCE (IEC/EN/
UL/CSA 60950-1).
Included Installat\
ion Instructions
© Panasonic System\C Networks Co\f, Ltd\f \b\C013
\fIDE button
(moves the camera \pto the “\fide” side)\p
TELE button(moves the camera \pto the “Tele” side)
I 2P power cable (accessory)
RJ-45 (female)
Network cable
Alarm input/output cable
Microphone/line input cable (white)
Audio output cable (black)LAN cable (category 5 or better 
straight, STP: For Europe)
4P alarm cable 
  (accessory)
Power cable 
(12 V DC)
12 V DC (red)
GND (black)
Screen display 
top (TOP)
NTSC/PAL switch 
						

							85 mm {3-11/32 inc\.hes}
(85.\f mm {3-3/8 inc\.hes})
25.4 mm 
{1 inch}*5
85 mm 
{3-11/32 inches}
(85.\f mm 
{3-3/8 inches})
138 mm 
{5-7/16 inches}25\f4 mm 
{1 inch}*5
138 mm 
{5-7/16 inches}
83.5 mm
{3-9/32 inches}
4\f mm
{1-13/1\f inches}
25.4 mm 
{1 inch}*5
\f3 mm
{2-15/32 inches}
25.4 mm 
{1 inch}*5\f3 mm
{2-15/32 inches}
83.5 mm
{3-9/32 inches}25.4 mm 
{1 inch}*5
108.5 mm
{4-9/32 inche\f}
70 mm
{2-3/4 inche\f}25.4 mm 
{1 inch}*5
\bo\fition A \bo\fition D
\bo\fition B
\bo\fition C \bo\fition E
\bo\fition F
Attachment plate (\iaccessory)
Fi\fing screws for att\iachment plate\b \f4 (\iM4, locally procur\ied) T
wo-gang junction bo\f 46 mm {1-13/16 inch\ies
}
83.5 mm
{3-9/32 inches}
In\ftallation
Step2 Fixing the bracketsStep1 Preparations
The installation tasks are explained using 4 steps.
There are 4 methods to install the camera to a ceiling or wall as described below . Prepare the 
required parts for each installation method before starting the installation.  The following are the 
requirements for the various installation methods.
Installation method Recommended 
screw Minimum pull-out 
strength (per 1 pc.)
[1] Mount the camera on the two-gang junction  box using the attachment plate.  M4 screws x 4
196 N {44 lbf}
[2] Directly mount the camera onto the ceiling or  wall using the attachment plate (when wiring 
can be installed in the ceiling or wall).  M4 screws x 4
196 N {44 lbf}
[3] Mount the camera onto the ceiling or wall using  the base bracket (when conduits are used for 
wiring, or when there is no space available for 
wiring in the ceiling or the wall).*
1
 M4 screws x 4 196 N {44 lbf}
[4] Mount the camera embedded to a ceiling using  the WV-Q169A (ceiling mount bracket: approx. 
705 g {1.55 lb}).*
1*2— There is sufficient 
strength in the ceiling
*1   Use 4 screws (M4 × 8 mm, accessory) to fix the attachment plate to the base bracket or 
WV-Q169A.
*2  
For information on how to mount the camera embedded to a ceiling using WV-Q169A, refer 
to the Instruction Manual provided with the WV-Q169A (ceiling mount bracket).
IMPORTANT:
 
● Procure 4 screws (M4) to secure the attachment plate (accessory) or base bracket 
(accessory) to a ceiling or a wall.
 
● The minimum required pull-out capacity of a single screw or anchor bolt is 196 N 
{44 lbf} or more when mounting with the installation method [1] to [3] above.
 
● When  mounting the camera on a concrete ceiling, use an AY plug bolt (M4) for 
securing. (Recommended tightening torque: 1.6 N·m {1.18 lbf·ft})
 
● Select screws according to the material of the ceiling  or wall that the camera will be 
mounted to. In this case, wood screws and nails should not be used.
 
● If a ceiling board such as plaster board is too weak to support the total weight, the 
area shall be sufficiently reinforced.
[1] Using a two-gang junction box
[2] Directly mount the camera to the ceiling or wall using the attachment plate
[3] Mount the camera to a ceiling or a wall using base bracket
< When using the conduit on the ceiling 
or wall for wiring>
The base bracket can be fixed in any of the following 6 screwing positions 
according to ceiling and wall conditions. Match the hole used when 
installing the camera to any of positions A to F.

A  Remove the cap for the female thread for 
the conduit by using a hexagon wrench 
(ISO 2936, width across flats S=5 mm 
{3/16 inches}).
B Mount the attachment plate and 
the base bracket.
Attachment plate (accessory) \bixing screws for attach-
ment plate: x4 (M4,\p locally 
procured)
φ25.4 mm
*3
{1 inch}
φ73 mm
*4
{2-7/8 inches}
*5 The wiring hole diameter is 25.4 mm  {1 inch}. Select any of the 2 base bracket fixture holes of 
G  template B when installing the base bracket. After mounting the attachment plate, the mounting 
direction of the camera can be adjusted in 90° increments.
*6 When attaching the base bracket to a one-gang junction box in Position E, secure the base bracket  with 2 screws (M4,  locally procured
).IMPORTANT:
 
● If open wiring is conducted, be sure to use conduits and run the cables inside 
the tubes to protect the cables from direct sunlight.
 
● Installation work shall be such that there is no exposure to water into the 
architecture through the conduits having been joined.
Step1
Make sure all items are prepared 
before beginning installation.
Step2
Mount the brackets to a ceiling or 
wall
Step3
Connect cables, and then attach the 
camera to the mount bracket.
Step4
Adjust the angle of view and focus, 
and then mount the enclosure.
FRONT
Cap for the female 
thread for the con-
duit Base bracket (acce\pssory)
\bixing screws (M4x4, locally\p 
procured)
Minimum pull-out
strength: 196 N {44.06 lbf} 
(per 1 pc.) 
\bixing screws for attachment \p
plate: x4 (accessor\py)
(Recommended tightening 
torque: 0.78 N·m {0.58 lbf·ft}) Attachment plate 
(accessory)
*3
 If the mounting direction of the camera has already been determined
Align the FRONT direction (the direction of FRONT marker on the camera that indicates the 
installation direction when installing the camera) of  F
 template A with the desired direction, and 
drill through a 25.4  mm {1 inch} diameter hole.
*4
   If the mounting direction of the camera is not determined yet or if you want to change 
the direction of the camera after it has been installed
If you want to be able to change the direction of the camera, drill through a 73 mm {2-7/8 inches} 
diameter hole in the center. By doing so you can adjust the mounting direction of the camera in 
90° increments.
Step3 Mount the camera to the attachment plate
Step4 Adjustment
A  Check the position of attachment 
mounting screws on the rear side 
of the camera. B 
Connect cables to the camera according to 
the instructions in “Making connections”, and 
mount the camera by inserting the attachment 
mounting screws into the holes of the attach -
ment plates. CLoosen the enclosure fixing screws.
D Remove the enclosure from the camera, 
and secure the camera using camera 
fixing screws.
Note:
 
● After cables have been connected to the camera, align the OPEN mark of the enclosure 
side panel with the protruding part of base bracket, insert 2 attachment mounting screws 
into the attachment plate, and rotate the camera approximately 15°.  The LOCK mark is 
moved to the protruding part of base bracket and the camera is temporarily secured. 
(When directly attaching the attachment plate to a ceiling or wall, align the OPEN mark to 
the tab position of the attachment plate.) 
*The fixing angle of the camera can be rotated in 90° increments
.
Note:
 
● Loosen 4 enclosure fixing screws 
using the bit (accessory).
IMPORTANT:
 
● Be sure to tighten the camera fixing 
screw. Failure to observe this may 
cause camera trouble due to camera 
falling. (Recommended tightening 
torque: 0.78 N·m {0.58 lbf·ft})
A Turn on power for the camera by either 
connecting a LAN cable or a 12 V DC 
power cable.
B  Connect the MONITOR OUT conversion 
plug (accessory) to the MONITOR OUT 
terminal of the camera, and then connect 
the monitor for adjustment with a RCA 
pin cable (locally procured).
 
● The camera is set to be connected to the 
NTSC monitor for adjustment at factory 
shipment.
Horizontal position (Panning): ±180°
Vertical position (Tilting): 0° to 85°
Image tilt adjustment: 
-45°(Left) to +300°(Right)
 
● To remove the SD memory card, hold down the SD ON/OFF 
button for about 2 seconds. When the flashing SD MOUNT 
indicator goes out, you can remove the SD memory card.
 
● After the SD memory card has been replaced, press the 
SD ON/OFF button, and make sure the SD MOUNT 
indicator is continually lit. (If you replace both SD memory 
cards, press the SD ON/OFF button after replacing the 
cards.)
 
● If you do not press the SD ON/OFF button after replacing 
the SD memory card, the SD MOUNT indicator 
is 
continually lit
 approximately 5 minutes later.
 
● When adjusting the viewing angle, make sure not 
to touch the light-blocking rubber ring or IR LED 
cover. Fingerprints or dirt can reduce the quality of 
viewed images.
C Adjust the angle of the camera with the 
tilt table, pan table, and azimuth adjust -
ment ring, and then adjust the viewing 
angle by pressing the WIDE or TELE 
buttons. D
Insert an SD memory card into the slot, 
if necessary. E 
Disconnect the monitor for adjustment 
after adjusting the focus by pressing the 
AF button.
F  Attach the enclosure. (Remove the protection film from inside 
of the dome cover, match the protruding 
part of base bracket to LOCK mark 
of the enclosure, and then attach the 
enclosure.) 
E MONITOR OUT conve\prsion plug 
(accessory)
NTSC⇔PA L
\fIDE
Note:
 
● When the screen size is adjusted using the WIDE ⇔TELE button, the camera’s focus is 
automatically adjusted with the basic focus adjustment function each time the 
WIDE⇔TELE button is pressed.
 
● When mounting the camera on a ceiling, adjust the tilt angle so that the  TOP mark above 
the lens always comes to the top side.
 
● When the camera is installed to a wall, the image is reversed in the default settings.  To  
correct the way the image is displayed, rotate the azimuth adjustment ring 180° clockwise, 
or select “On” for “Upside-down” from the setup menu. For information about performing 
the “Upside-down” setting from the setup menu, refer to the Operating Instructions 
(included in the CD-ROM).
 
● Remove the camera using the reverse order of the installation procedures.
IMPORTANT:
 
● Securely tighten all the fixing screws (x4) of enclosure. Otherwise, camera dropping 
may result in injury. (Recommended tightening torque: 0.78 N·m {0.58 lbf·ft})
 
● Defocus may be caused by the reinstalled enclosure. In this case, perform the auto 
focus function from the setup menu. 
 
● Remove the cover film from the dome cover.
Approx. 15°
Enclosure
Camera fixing screw
Attachment mountin\pg screws
IMPORTANT:
 
● Disconnect the  12 V DC power source and PoE power source to prevent power from being 
supplied during mounting work. 
 
● Enclosure is fixed at the installation auxiliary wire to the camera body , please do not 
remove the installed auxiliary wire.
 
● For installations on the wall, to prevent water from accumulating on the surface of the 
dehumidifying device, install the camera so that the dehumidifying device does not face up. 
If water accumulates on the surface of the dehumidifying device, it cannot function properly.
A\b
SD1, SD2
TELE
< 
When drilling a hole through the 
ceiling or wall for wiring>
 
● The female thread for conduit is compliant 
with ANSI NPSM (parallel pipe threads) 
3/4 inches or G3/4 of ISO 228-1.
*6
After installing the camera, refer to “Configure the settings of the camera (leaflet) ” and 
perform the camera settings.
Tab position 
of the attach-
ment plate 
(x4)
Conduit
Protruding part (x4)
Direction marker 
for installation 
(\bRONT
)
 
● Insert the SD memory card with its label 
facing down.
46 mm
{1-13/16 inches}
83.5 mm
{3-9/32 inches}