Panasonic Network CameraWv Sfv781l Installation Guide

							IMPORTANT:
How to wind the supplied waterproof tape
 
● Also waterproof the  I
 2P power cable (accessory), 
H  4P alarm cable (accessory), and external connec -
tions in the same way.
 
● Stretch the tape to approx. twice its length (see the 
illustration) and wind it around the cable. Insufficient 
tape stretch causes insufficient waterproofing.
 
● To prevent the LAN cable hook from coming loose 
easily, fit the  J
 LAN connector cover (accessory) 
onto the pigtail cable as illustrated, and then slide it in 
the direction indicated by the arrow. 
The connector of the LAN connector used with this 
camera must meet the following restrictions.  
Height when inserted (From bottom to hook.):   
Max. 16 mm {5/8 inches} 
Connector width: Max. 14 mm {9/16 inches}
 
● To install this product outdoors, be sure to waterproof 
the cables. Waterproof grade (IEC IP66 or equiva -
lent) is applied to this product only when it is installed 
correctly as described in these operating instructions 
and appropriate waterproof treatment is applied. The 
internal parts of B base bracket (accessory) are not 
waterproofed.
Standard accessories
Important Information  ...............................1 pc.
Installation Guide (this document)  ............ 1 set
Warranty card  ........................................... 1 setCD-ROM*1 
................................................. 1 pc.
Code label*2  .............................................. 1 pc.
Camera caution label ................................1 pc.
*1 
The CD-ROM contains the operating instructions and different kinds of tool software programs.
*2   This  label  may  be  required  for  network  management.  The  network  administrator  shall  retain 
the code label.
●   This manual describes the installation procedures, network camera instal\
lation, cable 
connections, and the angle of view adjustment.
●   Before reading this manual, be sure to read the Important Information.
For U.S. and Canada:
Panasonic System Communications 
Company of North America,
Unit of Panasonic Corporation
of North America
www.panasonic.com/business/
For customer support, call 1.800.528.6747
Two Riverfront Plaza, Newark, NJ 07102-5490
Panasonic Canada Inc.5770 Ambler Drive, Mississauga,
Ontario, L4W 2T3 Canada 
(905)624-5010
www.panasonic.ca For Europe and other countries:
Panasonic Corporation
http://www.panasonic.com
Panasonic System Networks Co., Ltd.  
Fukuoka, Japan
Authorised Representative in EU:
Panasonic Testing Centre
Panasonic Marketing Europe GmbH
Winsbergring 15, 22525 Hamburg, Germany

PGQX1816XA  Cs0415-2055 
Printed in China
 < Alarm input/output cable, power cable, microphone/
line input cable, audio/monitor output cable
>
2x
Stretch the tape to 
approx. twice its length.
 
● The output of the MONITOR OUT terminal can be switched to that for NTSC monitor or PAL monitor.
NTSC/PAL switch
The hook engages 
with the connector 
terminal
J
 
LAN connector cover (accessory)
 
● When AF (Auto Focus) operation is being executed  Blinks red (Interval of 1 time/ second) 
● When the set is being started  Lights red
 
● When an SD memory card is recognized normally  Lights red → Lights off
 
● When the SD memory card slot is not used or   Lights red → Stays red 
an abnormality is detected in SD memory card   
after the camera has started
SD ERROR/AF indicator
*1 SDXC/SDHC/SD memory card is described as SD memory card.
Powered speaker
Adjustment monitor
Analog monitor
PoE device (hub)
PC
LAN cable
(category 5 or better, straight)
Microphone
GND (black)
ALARM IN3, AUX OUT, DAY/NIGHT OUT (gray)  
(Alarm input 3, AUX output, DAY/NIGHT switching output)
ALARM IN2, ALARM OUT (red) (Alarm input 2, Alarm output)
ALARM IN1, DAY/NIGHT IN (green) (Alarm input 1/ DAY/NIGHT switching input)
Note:
 
● The ACT indicator, LINK indicator, SD ERROR/AF indicator, and SD MOUNT i\
ndicator are 
visible from underneath the camera. These LED indicators may light or bl\
ink when the 
camera is operating and can be kept turned off by the software settings.\
 (Indicators are set 
to light or blink in the default settings.) Turn off the indicators as \
required according to the 
installation environment. ( ☞ Operating Instructions (included in the CD-ROM))
*2
  
Data Matrix is our website address converted into a two-dimensional barc\
ode. 
Depending on the scanning application used, the Data Matrix may not be a\
ble to 
be read correctly. In such a case, directly enter the following URL.  
http://security.panasonic.com/pss/security/support/qr_sp_select.html
Data Matrix: 
To our website*2
SD memory card slot
MONITOR OUT terminal
(factory shipment:NTSC 
monitor)
Pan table fixing screw
Camera fixing screw
WIDE button 
(moves the camera to the “Wide” side) Auto focus (AF) button
TELE button
(moves the camera to 
the “Tele” side) SD MOUNT indicator
SD ERROR/AF indicator
ACT indicator
LINK indicator
Direction marker for installation (
⇧ TOP)
 
●   Points up when installing to a wall.
Auxiliary wire
Screen display top (TOP)
INITIAL SET button  NTSC/PAL switch
SD ON/OFF button
Direction marker for installation (FRONT
⇩) 
●   FRONT must positioned in front of the camera 
(on the Panasonic logo side).
Installation Guide
Network Camera
Model No.  WV-SFV781L
Included Installation Instructions
Major operating controls
The component names of the camera are as follows. Refer to the illustrat\
ion when installing or 
adjusting the camera.
B  Base bracket 
(accessory)
Cap for the 
female thread for 
the conduit Panning 
table
Tilting 
table
Tilt  
fixing 
screw
A
  
Attachment plate 
(accessory)
IR LEDLight-blocking 
rubber ring
Dome cover 
(Rain wash 
coating)
Camera
C   
Fixing screws for 
attachment plate 
(accessory)
●  How to initialize the camera
Follow the steps below to initialize the network camera.
1  
Turn off the power of the camera. When using a PoE hub, disconnect the LAN cabl\
e from the cam-
era. When using an external power supply, disconnect the 2P power cable plug from the camera.
2  Turn on the power of the camera while holding down the INITIAL SET button, and then keep 
holding down the button for 5 seconds or more. The camera will start up after about 2 minutes of 
taking off the INITIAL SET button and the settings including the network settings will be initiali\
zed.
IMPORTANT:
 
●When  the  camera  is  initialized,  the  settings  including  the  network  settings  will  be  initialized. 
Note that the CRT key (SSL encryption key) used for the HTTPS protocol will not be initialized.
 
● Before initializing the settings, it is recommended to write down the setting\
s in advance.
 
●Do not turn off the power of the camera during the process of initialization. Otherwise, it 
may fail to initialize and may cause malfunction.
INITIAL SET button
1  
If the SD ON/OFF button is pressed (for 1 second or less), the SD MOUN\
T indicator lights up 
green, and data can be saved on the SD memory card*1.
2   When the SD ON/OFF button is held down for about 2 seconds, the SD MOUNT\
 indicator 
goes out, and the SD memory card can be removed.
SD ON/OFF button
 
● When an SD memory card is inserted and could  Lights off → Blinks green → 
be recognized  Lights off
 
● When data can be saved after the SD memory card is   Lights off → Lights green 
inserted and the SD ON/OFF button is pressed  
(for 1 second or less)
 
● When data can be saved to the SD memory card  Lights green
 
● When the SD memory card is removed after holding down  Lights green → Blinks green → the SD ON/OFF button for about 2 seconds  Lights off (recording) 
   Lights green →  
 
 Lights off (waiting for recording) 
● When data cannot be saved to the SD memory card because Lights offan abnormality was detected or the SD memory card is 
configured not to be used
SD MOUNT indicator
 
● When data is being sent via the network camera  Blinks green (accessing)
ACT indicator
 
● When the camera is able to communicate with the  Lights orange 
connected device
LINK indicator
Making connections
Turn off each system’s power supply before making a connection. Before making connections, 
prepare the required peripheral devices and cables.
IMPORTANT:
 
● Use all 4 pairs (8 pins) of the LAN cable (category 5 or better, straight, STP).
 
● The maximum cable length is 100 m {328 feet}.
 
● Make sure that the PoE device in use is compliant with IEEE802.3af stand\
ard.
 
● When connecting both the 12 V DC power supply and the PoE device for pow\
er 
supply, 12 V DC will be used for power supply*.
* If a 12 V DC power supply and a PoE hub or router are used at the same\
 time,  network connections may not be possible. In this case, disable the PoE s\
ettings.  
Refer to the operating instructions of the PoE hub or router in use.
* Depending on the PoE device used, if you stop the 12 V DC power supply\
 after  operating it and a PoE hub or router at the same time, the power supply \
may stop, 
causing the camera to restart.
 
● When the LAN cable is disconnected once, reconnect the cable after aroun\
d 2 seconds. 
When the cable is quickly reconnected, the power may not be supplied fro\
m the PoE device.
 
● When cables are used outdoors, there is a chance that they may be affected by 
lightning. In this case, install a lightning arrester just before where \
the cables con -
nect to the camera.
Connect a LAN cable
I  2P power cable 
(accessory)
RJ45 (female)
Network cable
Alarm input/output cable  (External I/O terminal)
Microphone/line input cable (white)
Audio/monitor output cable (black)
LAN cable  
(category 5 or better, straight)
H   4P alarm cable 
(accessory)
Power cable 
(12 V DC) 12 V DC (red)
GND (black)
Connect the audio/monitor output cable to an external speaker with 
an amplifier.
Connect a stereo mini plug (ø3.5 mm {1/8 inches}).*
 
● Output impedance: Approx. 600 Ω (unbalanced)
 
● Recommended cable length: Less than 10 m {32.8 feet}
 
● Output level: -20 dBV (can switch to monitor output)
IMPORTANT:
 
● Connect/disconnect the audio cables and turn on the power of the camera \
after turn -
ing off the power of the audio output devices. Otherwise, loud noise may be he\
ard 
from the speaker.
 
● Make sure that the stereo mini plug is connected to this cable. When a m\
onaural mini 
plug is connected, audio may not be heard.  
When connecting a monaural speaker with amplifier, use a locally procured  conver-
sion cable (mono-stereo).
* Use an external powered speaker.
Waterproof treatment for the cable joint sections
Adequate waterproof treatment is required for the cables when installing\
 the camera with cables exposed 
or installing it under the eaves. The camera body is waterproof, but the cable ends are not waterproof.
Be sure to use the supplied waterproof tape at the points where the cabl\
es are connected to apply 
waterproof treatment in the following procedure. Failure to observe this\
 or use of a tape other than the 
provided waterproof tape (such as a vinyl tape) may cause water leakag\
e resulting in malfunction.
Wind the tape in a  
half-overlapping manner.
Wind the tape in a  
half-overlapping 
manner.
IMPORTANT:
 
● Be sure to use the H 4P alarm cable (accessory) provided with this product.
 
● Install external devices so that they do not exceed the ratings above.
 
● When using the external I/O terminals as the output terminals, ensure th\
ey do not 
cause signal collision with external signals.
Connect the alarm input/output cable

• ALARM IN1 (DAY/NIGHT IN), ALARM IN2, ALARM IN3Input specification:  No-voltage make contact input (4 V - 5 V DC, internally pulled up)
OFF:  Open or 4 V - 5 V DC
ON:  Make contact with GND (required drive current: 1 mA or more)
• ALARM OUT, AUX OUT, DAY/NIGHT OUT Output specification:  Open collector output (maximum applied voltage: 20 V DC)
Open:  4 V - 5 V DC by internal pull-up
Close:  Output voltage 1 V DC or less (maximum drive current: 50 mA)
* The default of EXT I/O terminals is “OFF”.
Note:
 
● Off, input, and output of the external I/O terminal 2 and 3 can be switche\
d by config-
uring the setting. Refer to the Operating Instructions on the provided C\
D-ROM for 
further information about the external I/O terminal 2 and 3 (ALARM IN2,\
 3) settings 
(“Off”, “Alarm input”, “Alarm output”, “AUX output” or \
“DAY/NIGHT switching output”).
H 4P alarm cable (accessory)
Connect the output cable of the AC adaptor to the I 2P power cable  (accessory).
Power cable
 12 V DC
Red  Positive
Black  Negative
Connect the power cable
IMPORTANT: 
● Use 12 V DC power supply that is insulated from the commercial AC power.
 
● Be sure to use the I 2P power cable (accessory) provided with this product.
 
● Be sure to fully insert the I 2P power cable (accessory) into the 12 V DC power 
supply terminal. Otherwise, it may damage the camera or cause malfunctio\
n.
 
● When installing the camera, make sure that excessive force is not applie\
d to the power cable. 
● Be sure to use an AC adaptor compliant with the specifications (written in the indication\
 label on the bottom side of this unit) regarding power source and power\
 consumption.
Caution: 
● A READILY ACCESSIBLE DISCONNECT DEVICE SHALL 
BE INCORPORATED TO THE EQUIPMENT POWERED 
BY 12 V DC POWER SUPPLY.
 
● ONLY CONNECT 12 V DC CLASS 2 POWER SUPPLY (UL 
1310/CSA 223) or LIMITED POWER SOURCE (IEC/EN/
UL/CSA 60950-1).
Microphone/line input cable
Connect a stereo mini plug (ø3.5 mm {1/8 inches}).
 
● Input impedance: Approx. 2 kΩ (unbalanced)
 
● Recommended cable length: Less than 1 m {3.28 feet} (for microphone inp\
ut)  
Less than 10 m {32.8 feet} (for line input)
 
● Recommended microphone: Plug-in power type (option)  
•Supply voltage: 2.5 V ±0.5 V 
•Recommended sensitivity of microphone: -48 dB ±3 dB (0 dB=1 V/Pa,1 kHz)
 
● Input level for the line input: Approx. -10 dBV
When connecting to a network using a PoE hub
Before starting the installation, check the entire system configuration.  The following illustration 
gives a wiring example of how to connect the camera to the network via a\
 PoE device (hub).

LAN cable (category 5 or better, straight)
Use a LAN cable (category 5 or better, cross) when directly connecting the camera to a PC.
IMPORTANT:
 
● The adjustment monitor is used for checking the adjustment of the angula\
r field of view 
when installing the camera or when servicing. It is not provided for rec\
ording/monitoring use.
 
● Depending on the monitor, some characters (camera title, preset ID, etc.) may not be 
displayed on the screen.
 
● Use a switching hub or a router which is compliant with 10BASE-T/100BASE\
-TX.
 
● If a PoE hub is not used, each network camera must be connected to a 12 \
V DC power supply. 
● When using 12 V DC, power supply from a PoE hub or router is not require\
d.
There are 3 methods to install the camera to a ceiling or wall as descri\
bed below. Prepare the 
required parts for each installation method before starting the installa\
tion. The following are the 
requirements for the various installation methods.
Installation method Recommended 
screw Minimum pull-out 
strength
[1] Mount the camera onto the ceiling or wall using the B
 base bracket (accessory) (when conduits 
are used for wiring, or when there is no space 
available for wiring in the ceiling or the wall).
*1
 M4 screws x 4 539 N (121 lbf)/1 pc.
[2] Mount the camera on the two-gang junction  box using the  A attachment plate (accessory).  M4 screws x 4
539 N (121 lbf)/1 pc.
[3] Directly mount the camera onto the ceiling or  wall using the attachment plate (when wiring 
can be installed in the ceiling or wall).  M4 screws x 4
539 N (121 lbf)/1 pc.
*1   When securing the attachment plate to the base bracket, use the  C Fixing screws for at-
tachment plate (accessory) (M4 x 8 mm {5/16 inches})
Preparations
The following parts are used during installation procedures.
A Attachment plate  .................................. 1 pc.
B Base bracket  ........................................ 1 pc.
C   Fixing screws for attachment plate 
   (M4 x 8 mm {5/16 inches})  ................5 pcs.
(incl. 1 spare)
D 
Template A (for the attachment plate)  .... 1 sheet
E
 Template B (for the base bracket)  ..... 1 sheet F  
Bit (Hex wrench, screw size 
   6.35 mm {1/4 inches} T20)  .................... 1 pc.
G Waterproof tape  ................................... 1 pc.
H 4P alarm cable  ..................................... 1 pc.
I 2P power cable  .................................... 1 pc.
J LAN connector cover  ........................... 1 pc.
K MONITOR OUT conversion plug *3  ...... 1 pc. 
L Protection cover  ................................... 1 pc.
M Extended safety wire ............................1 pc.
(Hex wrench, screw size 6.35 mm {1/4 inches} T20)
FG
*
3 This can be used as MONITOR OUT by 
switching the audio/monitor output cable of 
the unit using software switching.  
Connect the MONITOR OUT conversion 
plug to the audio/monitor output cable and 
use it when converting the ø3.5 mm 
{1/8 inches} stereo mini jack to the RCA pin 
jack output.
© Panasonic System Networks Co., Ltd. 2015 Yaw fixing screw
   
						

							Step3 Adjustment
A Hook a finger on either one of the 2 
projections (parts shown by the arrow 
below) at the head of the camera and 
open the IR LED mounting section of 
the camera.
 
●  When opening the IR LED mounting 
section, be careful not to touch the light-
blocking rubber, IR LED cover, or camera 
lens section. Fingerprints, etc. may cause 
the image quality to deteriorate.
 
● The IR LED mounting section can be 
temporarily secured by opening it to its 
fullest extent.
B Connect the monitor for adjustment to 
the MONITOR OUT terminal with an 
RCA pin cable (locally procured).
 
● The NTSC monitor for adjustment can 
be connected in the default settings of 
the camera.
C Turn on the camera. Make sure that 
the LINK indicator lights up orange, 
and the ACT indicator is blinking 
green. (Refer to the descriptions in 
“Major operating controls” for more 
information about the indicators.)
D 
When using the SD memory card, fol-
low the procedure below to mount it.
 
● Turn the label side of the SD memory 
card to face the lens side of the cam-
era, and line it up with the SD memory 
card insertion slot.
 
● Insert the SD memory card into the 
socket, and push it in until a click 
sound is heard.
Projection
Projection
MONITOR 
OUT
SD memory card 
insertion slot
SD memory 
card IR LED 
mounting 
section
IR LED mounting section
IR LED coverLight-blocking rubber ring
Note:
 
● To remove the SD memory card, hold down the SD ON/OFF button for about 2 seconds. 
When the flashing SD MOUNT indicator goes out, you can remove the SD memory card.
 
● When the replacement of the SD memory card is complete, press the SD ON/\
OFF 
button (for 1 second or less), and check that the SD MOUNT indicator lights up.
 
● If you do not press the SD ON/OFF button after replacing the SD memory c\
ard, the 
SD MOUNT indicator is automatically lit approximately 5 minutes later.
Installation
Step1 Fixing the brackets [1]
The installation tasks are explained 
using 3 steps.Step1 Fixing the bracketsStep2 Mount the camera to the attachment plateStep3 Adjustment
Pan angle: ±180°
Tilt angle: 0 to 85°
Yaw angle: -45° (left) to +300° (right)
E 
Loosen the pan table fixing screw, tilt 
table fixing screw, and yaw fixing screw 
to adjust the angle of the camera, 
and then adjust the viewing angle by 
pressing the WIDE or TELE button.
G Disconnect the monitor for adjustment 
from the MONITOR OUT terminal 
and finally close the IR LED mounting 
section.
F
  After adjusting the viewing angle, 
tighten each fixing screw.
 
● Pan table fixing screw (Recommended 
tightening torque: 0.59 N·m {0.44 lbf·ft})
 
● Tilt table fixing screw (Recommended 
tightening torque: 0.59 N·m {0.44 lbf·ft})
 
● Yaw fixing screw should be tighten firmly 
by hand.
Pan table fixing screw
Pan angle
Tilt angle
Tilt table fixing screw
WIDE 
button TELE button
TOP markYaw angle
IR LED mounting 
section
Note:
 
● When the screen size is adjusted using the WIDETELE button, the camera’s focus is 
automatically adjusted with the basic focus adjustment function each tim\
e the   
WIDE button or TELE button is pressed.
 
● Note that the camera silhouette appears depending on the adjustable angl\
e or zoom ratio.
 
● When mounting the camera, adjust the pan, tilt, and yaw angles so that t\
he TOP mark of 
the lens always comes to the top side.
 
● When the camera is installed on a wall, the image is rotated 180° upside down in the default 
settings. To correct the way the image is displayed, rotate the PAN angle 180° clockwise, or 
select “On” for “Upside-down” from the setup menu. Refer to \
the “Operating Instructions” 
(included in the CD-ROM) for information on how to set “Upside-down\
” in the setup menu.
 
● Take care so that the IR LED cable does not get caught when closing the I\
R LED mounting section.
 
● The pan table fixing screw, tilt table fixing screw, and yaw fixing screw may fall off if they 
are loosened excessively.
 
● When using the camera at a position where the camera lens is nearly hori\
zontal, part of 
an image may appear to be overlapped. In this case, decrease the vertica\
l position angle 
or adjust the zoom ratio.
Step2 Mount the camera to the attachment plate
A  Check the position of attachment 
mounting screws on the bottom 
side of the camera.  B 
Follow the instructions in “Making connections” 
to connect cables to the camera, then carry out 
waterproof treatment referring to “Waterproof 
Treatment for the Cable Joint Sections”.
C 
Align the 4 attachment mounting screws at the 
bottom of the camera with the holes in the 
A at-
tachment plate (accessory), and mount the camera.   
You can adjust the mounting direction of the 
camera in 90° increments. 
Make sure to hold both the camera body and protection 
cover when attaching the camera to the bracket.
Note:
 
● After connecting the cables to the camera, align the OPEN mark on the ca\
mera body 
side panel with the protruding part of the  B
 base bracket (accessory), insert 4 attach -
ment mounting screws into the attachment plate, rotate the camera approximately 15° 
clockwise when looking up at it as illustrated, and move the LOCK mark t\
oward the pro -
truding part of the base bracket to temporarily secure the camera. (Whe\
n directly mount -
ing the attachment plate to a ceiling or wall, align the OPEN mark with \
the hook on the 
attachment plate.)
Attachment mounting screws x 4
Dehumidifying device
IMPORTANT:
 
● Procure 4 screws (M4) to secure the  A
 attachment plate (accessory) or  B
 base 
bracket (accessory) to a ceiling or a wall.
 
● When  mounting the camera on a concrete ceiling, use an AY plug bolt (M4) for 
securing. (Recommended tightening torque: 1.6 N·m {1.18 lbf·ft})\
 
● Select screws according to the material of the ceiling  or wall that the camera will be 
mounted to. In this case, wood screws and nails should not be used.
 
● If a ceiling board such as plaster board is too weak to support the tota\
l weight, the 
area shall be sufficiently reinforced.
 
● If open wiring is conducted, be sure to use conduits and run the cables \
inside the 
conduit to protect the cables from direct sunlight.
 
● Installation work shall be such that there is no exposure to water into \
the architecture 
through the conduits having been joined.
[1] Mount the camera to a ceiling or a wall using base bracket
The B  base bracket (accessory) can be fixed in any of the following 5 screwi\
ng positions 
according to ceiling and wall conditions. Match the hole used when insta\
lling the camera to 
any of positions A to F.

108.5 mm
{4-9/32 inches}
ø25.4 mm 
{ø1 inch}*170 mm
{2-3/4 inches}
85 mm {3-11/32 inches}
(85.7 mm {3-3/8 inches})
85 mm 
{3-11/32 inches}
(85.7 mm 
{3-3/8 inches})ø25.4 mm 
{ø1 inch}*1
63 mm
{2-15/32 inches}
63 mm
{2-15/32 inches}ø25.4 mm 
{ø1 inch}*1
138 mm 
{5-7/16 inches}
138 mm 
{5-7/16 inches}
ø25.4 mm 
{ø1 inch}*1
46 mm
{1-13/16 inches}
83.5 mm
{3-9/32 inches}ø25.4 mm 
{ø1 inch}*1
Position APosition BPosition C
Position DPosition E*2Position F
*1 The wiring hole diameter is 25.4 mm  {1 inch}. Select any of the 2 base bracket fixture holes 
of  E
 template B (for the base bracket, accessory) when installing the base\
 bracket.
*2 When installing the WV-SFV781L, do not use Position E.
☞  For safety, a safety wire must be secured to a wall or ceiling. Refer to the “S\
ecuring a 
safety wire” leaflet for further information.

 
● Mount the  B
 base bracket 
(accessory) to a ceiling or wall 
using 4 fixing screws (M4, 
locally procured). Refer to the 
installation example on the 
right and pass the wiring 
through the base bracket.
 
● Secure  A
 attachment plate 
(accessory) to base bracket 
using 4  C
 attachment fixing 
screws (accessory).
(Recommended tightening 
torque: 0.78 N·m {0.58 lbf·ft})
Fixing screws (M4  x
 4, locally 
procured)
Minimum pull-out strength: 
539 N {121 lbf} (per 1 pc.)
C   Fixing screws for attachment 
plate: x 4 (accessory) 
(Recommended tightening 
torque: 0.78 N·m {0.58 lbf·ft})
B   Base 
bracket 
(accessory)
A   Attachment plate
(accessory)

A  
Remove the cap for the female thread for the 
conduit by using a hexagon wrench (ISO 2936, 
width across flats S=5 mm {3/16 inches}).
The female thread for conduit is compliant with 
ANSI NPSM (parallel pipe threads) 3/4 inches or 
G3/4 of ISO 228-1.
*  When making holes and wiring 
from a ceiling or wall, do not 
remove the cap for the female 
thread for the conduit.
B  Attach the base bracket and attachment 
plate to a ceiling or wall.
Cap for the female 
thread for the 
conduit
 
● Mount the base bracket to a 
ceiling or wall using 4 fixing 
screws (M4, locally procured). 
Refer to the installation example 
on the right and pass the wiring 
through the base bracket.
 
● Secure attachment plate to base 
bracket using 4 attachment fixing 
screws. (Recommended tightening 
torque: 0.78 N·m {0.58  lbf·ft})
Conduit
Fixing screws  
(M4  x
 4, locally procured)Minimum pull-out 
strength:
539 N {121 lbf} (per 1 pc.)
C  Fixing screws for attachment plate: x 4 (accessory)
(Recommended tightening torque: 0.78 N·m {0.58 lbf·ft})
B  Base bracket 
(accessory)
A  Attachment 
plate 
(accessory)
B  Base bracket (accessory)
H Attach the dome cover protected by 
the 
L protection cover (accessory) 
to the camera again, and fix it using 
the 2 dome fixing screws shown in 
illustration below.
(Recommended tightening torque: 
1.37 N·m {1.01 lbf·ft}) 
When attaching the dome cover 
protected by the protection cover, insert 
the extra part of the installation auxiliary 
wire into the processing groove.
IMPORTANT:
 
● When attaching the dome cover, process the wiring so that the installation auxiliary wire 
does not get caught. If the wire does get caught, the waterproofing perf\
ormance may be 
compromised.
 
● Securely tighten the 4 dome fixing screws. Failure to do so may cause th\
e camera to 
drop. Recommended tightening torque: 1.37 N·m {1.01 lbf·ft}
 
● After removing the  L
 Protection cover (accessory), take care not to touch the surface of 
the dome cover.
 
● When the dome cover is attached, the camera may go out of focus. After attaching the 
dome cover, start the auto focus function from the setup menu.
Auxiliary 
wire
Protection 
cover 
auxiliary 
part
The 1st dome setscrew (the 
2nd screw is placed at the 
opposing side of this screw.)
The 3rd dome setscrew 
(the 4th screw is placed 
at the opposing side of 
this screw.)
Hook of protection cover 
auxiliary part
(There is one more  
on the opposite side.)
L   
Protection 
cover (accessory)
Note:
 
● When removing the camera, perform removal by above the installation proc\
edure in 
the reverse order.
 
● After installation has been completed, store the  L
 Protection cover (accessory) to be 
used during servicing. When servicing the camera, remove the packing (2\
 pcs.) from 
the protection cover.
After installing the camera, refer to “Configure the settings of the \
camera”   
(leaflet) and perform the camera settings.
Auxiliary wire
Processing 
groove
I  Pull the 2 hooks of the protection 
cover auxiliary part outward at the 
same time, and remove the protection 
cover.
J  Secure with the 2 dome fixing screws 
shown in illustration below. (Secure 
the dome cover with 4 screws.)  
(Recommended tightening torque: 
1.37 N·m {1.01 lbf·ft})
D  Loosen the 2 dome fixing screws 
and remove the  L Protection cover 
(accessory) from the camera with it 
still attached to the dome cover.  
* 
  The dome cover is temporarily fixed 
to the camera using 2 dome fixing 
screws at factory shipment. The 
temporarily fixed dome fixing screws 
are the screws not attached to the 
protection cover auxiliary part.
E  Remove the protective packaging 
and fixing tape from the camera 
body. F 
Secure the camera using the camera 
fixing screws. 
(Recommended tightening 
torque: 0.78 N·m {0.58 lbf·ft})
IMPORTANT:
 
● Securely tighten the camera fixing 
screws. Failure to observe this may 
cause the camera to fall or water to seep 
in, which may cause a personal injury or 
damage the camera.
Note:
 
● Loosen the 2 dome fixing screws using 
the  F
 bit (accessory).
IMPORTANT:
 
● Disconnect the  12 V DC power source and PoE power source to prevent power from being 
supplied during mounting work. 
 
● The dome cover protected by the  L
 Protection cover (accessory) is connected to the cam -
era body using the auxiliary wire. Do not disconnect it.
 
● For installations on the wall, to prevent water from accumulating on the\
 surface of the 
dehumidifying device, install the camera so that the dehumidifying devic\
e does not face up. 
If water accumulates on the surface of the dehumidifying device, it cann\
ot function properly.
* The camera connection cables, protection 
cover, dome cover and IR LED cables are 
omitted in subsequent illustrations.
Camera fixing screw
Dome setscrew x 2 (The second screw is placed at the opposing side of this screw.)
Auxiliary wire
L   
Protection 
cover  
(accessory)
A Fixing the brackets [2][3]
[2] Using a two-gang junction box
[3] Directly attach the attachment bracket to the ceiling or wall
*3 When the camera attachment direction has been determined before insta\
llation  
Match the FRONT direction (the direction of the FRONT 
 direction marker when 
the camera is installed) of  D template A to the direction you want the camera to face 
and open a ø25.4 mm (1 inch) hole before starting the installation.\
  
Install the camera with the Panasonic logo of the camera facing the FRON\
T direction of template A.
*4 When the camera attachment direction has not been determined before i\
nstallation 
or when changing the camera direction after installation
To change the direction the camera faces, open a ø73 mm (2-7/8 inches\
) hole. The 
camera mounting direction can be changed in 90° increments.  
Information on installing or adjusting the camera is continued from Step\
 2.
A Attachment plate 
(accessory)
Fixing scr ews
(M4, locally pr ocured)
T
wo-gang junction
46 mm{1-13/16 inches} 83.5 mm
{3-9/32 inches}
A  Attachment plate (accessory) Fixing screws
(M4, locally procured)
ø25.4 mm
{1 inch}*
3
ø73 mm
{2-7/8 inches}*4
Attachment 
plate hook
(4 places)
FRONT
46 mm
{1-13/16 inches}
83.5 mm
{3-9/32 inches}
Protruding part  
(4 locations)
Wiring port
When attaching the attachment 
plate directly to a ceiling or wallWhen using the base 
bracket
Hook part
(
A  Attachment plate 
(accessory)) Protruding part
(
B  Base bracket (accessory))
■Image of the camera inserted into the attachment plate
A   Attachment plate 
(accessory) holes x 4 OPEN
Camera body
L Protection cover (accessory)
 
● After completing the adjustment, process 
the IR LED cable using the hook for wiring 
processing (A) or (C). Do not remove the 
IR LED cable from the hook for wiring 
processing (B) when adjusting the yaw 
angle.
When installing using an attachment plate, refer to “A Fixing the brackets [2][3]” in the bottom right of this page.
Hook for wiring 
processing (A)
Hook for 
wiring  
processing 
(C)
Yaw angle
IR LED cable
Hook for wiring 
processing (B)
Yaw fixing 
screw
Rotate the camera 
approximately 15° so that 
the LOCK mark is aligned 
with the protruding part.