Panasonic Projector PT-DS20KU User Manual

							[NETWORK] menu
ENGLISH - 131
Settings
Accessing from the Web browser
1) Start up the Web browser on the computer.
2)  
Enter the IP
  address set on the projector into the URL entry field of the Web browser.
3)
 
Enter the user name and the password.
▶z The factory default setting of the user name is user1 (user rights)/admin1 (administrator rights) and the 
password is panasonic (lower case).
4) Click OK.
▶zThe [Projector status] page is displayed.
Note
 zIf you use a W

eb browser to control the projector, set [WEB CONTROL] to [ON] in [NETWORK CONTROL] 
(
 page 128).
 z D

o not perform setting or control simultaneously by starting up multiple Web browsers. Do not set or control the 
projector from multiple computers.
 z Change the password first.( page 144)
 zT

he administrator rights allows to use all functions. The user rights allow use of [Projector status] (
 page 132), 
confirmation of the error information page (
 page 133), [Network status] ( page 134), [Basic control] ( page 136), 
and [Change password] (
 page 144) only.
 z Access will be locked for few minutes when an incorrect password is entered three times consecutively
. 
						

							[NETWORK] menu
132 - ENGLISH
Settings
▶■Descriptions of items
(1)
(2)
(3)
(4)
(5)
(1) Page tab
Switches pages by clicking it.
(2) [Status] The status of the projector is displayed by clicking 
this item.
(3) [Projector control] The [Projector control] page is displayed by clicking 
this item.
(4) [Detailed set up] The [Detailed set up] page is displayed by clicking 
this item.
(5) [Change password] The [Change password] page is displayed by clicking 
this item.
▶■[Projector status] page
Click [Status] → [Projector status].
Displays the status of the projector for the following items.
(10)
(11)
(12)
(15)
(16)(5)
(6)
(7)
(8)
(9)
(1)
(2)
(3)
(4)
(13)
(14)
(1) [PROJECTOR TYPE]
Displays the type of the projector.
(2) [MAIN VERSION] Displays the firmware version of the projector.
(3) [POWER] Displays the status of the power.
(4) [SHUTTER] Displays the status of the projector.
(5) [SERIAL NUMBER] Displays the serial number of the projector.
(6) [NETWORK VERSION] Displays the version of the firmware of the network.
(7) [REMOTE2 STATUS] Displays the control status of the  
terminal.
(8) [OSD] Displays the status of the on-screen display.
(9) [LAMP SELECT] Displays the setting status of [LAMP SELECT] 
(
 page 103).
(10) [INPUT] Displays the status of the input selection.
(1
1) [INTAKE AIR TEMPERATURE] Displays the status of the air intake temperature of 
the projector.
(12) [OPTICS MODULE TEMPERATURE] Displays the status of the internal temperature of 
the projector.
(13) [AROUND LAMP TEMPERATURE] Displays the status of the temperature around the 
lamp of the projector.
(14) [LAMP1][LAMP2][LAMP3][LAMP4][RUNTIME] Displays the status and the usage time of the lamp.
(15) [SELF TEST] Displays the self-diagnosis information.
(16) [PROJECTOR RUNTIME] Displays the operation times of the projector. 
						

							[NETWORK] menu
ENGLISH - 133
Settings
▶■Error information page
When [Error (Detail)] or [Warning (Detail)] is displayed in the self-diagnosis display of the [Projector status] 
screen, click it to display the error/warning details.
▶z
The projector may go into the standby status to protect the projector depending on the contents of the 
error

.
[OK]: Normal opera\Ation[FA\fLED]: O\b\burren\be of \Atrouble
[WARN\fNG]: Warning
▶zDescription of problem occurrence [F AILED]:
Parameter
Description
[MAIN CPU BUS] There is a problem with the microcomputer circuitry. Consult your 
dealer.
[FAN] There is a problem with the fan or the fan drive circuit. Consult your 
dealer.
[INTAKE AIR TEMPERATURE] The air intake temperature is too high. It may be used in an operating 
environment where the temperature is high, such as near a heating 
appliance.
[OPTICS MODULE TEMPERATURE] The temperature inside the projector is high. It may be used in an 
operating environment where the temperature is high, such as near 
a heating appliance.
[AROUND LAMP TEMPERATURE] The temperature around the lamp is high. The air exhaust port may 
be blocked.
[LAMP1 REMAIN TIME]
The usage time of the lamp has exceeded the specified time, and it 
is time to replace the lamp.
[LAMP2 REMAIN TIME]
[LAMP3 REMAIN TIME]
[LAMP4 REMAIN TIME]
[LAMP1 STATUS]
The lamp has failed to turn on. Wait a while until the luminous lamp 
cools off, and then turn on the power.
[LAMP2 STATUS]
[LAMP3 STATUS]
[LAMP4 STATUS]
[APERTURE(CONTRAST-SHUTTER)]
There is a problem in the contrast shutter circuit for dynamic iris. 
Consult your dealer.
[SHUTTER(MUTE-SHUTTER)] There is a problem with the shutter circuitry. Consult your dealer.
[INTAKE AIR TEMP.SENSOR] There is a problem with the sensor used to detect intake air 
temperature. Consult your dealer.
[OPTICS MODULE TEMP.SENSOR] There is a problem with the sensor used to detect temperature inside 
the projector. Consult your dealer. 
						

							[NETWORK] menu
134 - ENGLISH
Settings
ParameterDescription
[AROUND LAMP TEMP. SENSOR] There is a problem with the sensor used to detect exhaust air 
temperature. Consult your dealer.
[BATTERY] The battery replacement is required. Consult your dealer.
[LENS MOUNTER] There is a problem in the lens mounter. Consult your dealer.
[BRIGHTNESS SENSOR] There is a problem with the luminance sensor. If the problem is not 
corrected by turning off the power and turning it on again, consult 
your dealer.
[ANGLE SENSOR] There is a problem with the sensor that detects angle. Consult your 
dealer.
[FILTER UNIT] The air filter unit is not attached. Check the connection of the air filter 
unit. (
 page 150)
[AIR FIL
TER] There are too much dust accumulated in the air filter unit.
Turn off the  switch to  (
 page 53), and 
clean the air filter (
 page 148).
[AC POWER] AC input voltage is weak. Use electric wiring that can sufficiently 
withstand the power consumption of the projector
.
▶■[Network status] page
Click [Status] → [Network status].
The current network setting status is displayed. 
						

							[NETWORK] menu
ENGLISH - 135
Settings
▶■[Access error log] page
Click [Status] → [Access error log].
The error log on the WEB server is displayed such as access to the pages that do not exist or access with 
unauthorized user names or passwords.
▶■[Access log] page
Click [Status] → [Access log].
The log such as user name accessed to the WEB control page, accessed IP
 address, accessed time is 
displayed.
Note
 z [Access error log]/[Access log] will display the recent few thousand accesses/requests. May be unable to 
display all information when many accesses/requests are made at one time.
 zWhen [Access error log]/[Access log] exceeds a certain amount, old information will be erased.
 zConfirm [Access error log]/[Access log] periodically

. 
						

							[NETWORK] menu
136 - ENGLISH
Settings
▶■[Basic control] page
Click [Projector control] → [Basic control].
(1)
(2)
(4)
(5) (3)
(1) [POWER]
Switches the power on/off.
(2) [SHUTTER] Switches between use or not use of the shutter 
function.
(3) [OSD] Switches between on (display)/off (no display) of the 
on-screen display function.
(4) [SYSTEM] Switches the system method.
(5) [INPUT SELECT] Switches the input signal.
▶■[Detail control] page
Click [Projector control] → [Detail control].
(7)
(8)
(9)
(10)
(2)
(1)
(3)
(4)
(5)
(6)
(1) Control of the projector
The projector is controlled by clicking the buttons in 
the same way as the buttons on the remote control.
(2) [SUB MEMORY] Switches the sub memory.
(3) [SYSTEM DAYLIGHT VIEW] Switches to system daylight view settings.
(4) [FREEZE] Temporarily pauses the image.
(5) [P IN P] Switches the P IN P setting.
(6) [LEFT/RIGHT SWAP] (PT-DZ21KU and  PT-DS20KU only)
Switches the flip horizontal settings.
(7) [WAVEFORM MONITOR] Displays the waveform of the input signal.
(8) [LENS] Adjusts the projection lens.
(9) [TEST PATTERN] Displays the test pattern.
(10) [GET OSD] Updates the on-screen display of the projector at the 
right of the control page. 
						

							[NETWORK] menu
ENGLISH - 137
Settings
▶■[Network config] page
Click [Detailed set up] → [Network config].
▶z
Click [Network config] to display the [CAUTION!] screen.
▶zClick [Next] to display the current settings.
▶zClick [Change] to display the following setting change screen.
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(1) [PROJECTOR NAME]
Enter the name of the projector. Also enter the host 
name if it is required when using a DHCP server, etc.
(2) [DHCP ON]/[DHCP OFF] To enable the DHCP client function, set to [DHCP 
ON].
(3) [IP ADDRESS] Enter the IP address when not using a DHCP server.
(4) [SUBNET MASK] Enter the subnet mask when not using a DHCP 
server.
(5) [DEFAULT GATEWAY] Enter the default gateway address when not using a 
DHCP server.
(6) [DNS1] Enter the DNS 1 server address.
Permissible characters for the entry of DNS 1 server 
address (primary):
Numbers (0 to 9), period (.)
(Example: 192.168.0.253)
(7) [DNS2] Enter the DNS 2 server address.
Permissible characters for the entry of DNS 2 server 
address (secondary):
Numbers (0 to 9), period (.)
(Example: 192.168.0.254)
(8) [Back]/[Next] Click the [Back] button to return to the original screen.
[Next]The current settings are displayed by pressing 
the button. Click the [Submit] button to update the 
settings.
Note
 zWhen you use the “Forward” and “Back” functions of your browser

, a warning message “Page has Expired” 
may appear. In that case, click [Network config] again since the following operation will not be guaranteed. 
						

							[NETWORK] menu
138 - ENGLISH
Settings
▶■[Adjust clock] page
Click [Detailed set up] → [Adjust clock].
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(1) [Time Zone]
Selects the time zone. 
(2) [Set time zone] Updates the time zone setting.
(3) [NTP SYNCHRONIZATION] Set to [ON] to adjust the date and time automatically.
(4) [NTP SERVER NAME] Enter the IP address or server name of the NTP 
server when you set to adjust the date and time 
manually.
(To enter the server name, the setup of the DNS 
server is required.)
(5) [Date] Enter the date to be changed.
(6) [Time] Enter the time to be changed.
(7) [Set date and time] Updates the date and time settings.
Note
 zThe replacement of the battery inside the projector is required when the time goes out of alignment right after 
correcting the time. Please consult your dealer

.
▶■[Ping test] page
You can check whether the network is connected to the E-mail server, POP server, DNS server, etc.
Click [Detailed set up] → [Ping test].
(1)
(2)
(3)
(4)
(1) [Input IP address] Enter the IP address of the server to be tested.
(2) [Submit] Executes the connection test.
(3) Example of display when the connection has  succeeded
(4) Example of display when the connection has  failed 
						

							[NETWORK] menu
ENGLISH - 139
Settings
▶■[E-mail set up] page
E-mail address set in advance for use when there is a problem or when the usage time of a lamp reaches a 
set value.
E-mail can be sent to (maximum two locations).
Click [Detailed set up] → [E-mail set up].
(1)
(2)
(3)
(4)
(5)
(6)
(1) [ENABLE]
Select [Enable] to use the E-mail function.
(2) [SMTP SERVER NAME] Enter the IP address or the server name of the E-mail 
server (SMTP). To enter the server name, the DNS 
server settings are required.
(3) [MAIL FROM] Enter the E-mail address of the projector. (Up to 63 
characters in single byte)
(4) [MEMO] You can enter information such as the location of the 
projector that notifies the sender of the E-mail. (Up to 
63 characters in single byte)
(5) [MINIMUM TIME] Change the minimum interval for the temperature 
warning mail. The default value is 60 minutes. In this 
case, another E-mail will not be sent for 60 minutes 
after sending the temperature warning mail even if it 
reaches the warning temperature.
(6) [INTAKE AIR TEMPERATURE] Change the temperature setting for the temperature 
warning mail. A temperature warning mail is sent 
when the temperature exceeds this value.
(8)
(7)
(7) [E-MAIL ADDRESS 1]Enter the E-mail address to be sent.
(8) Settings of the conditions to send E-mail Select the conditions to send E-mail.
[MAIL CONTENTS]: Select either [NORMAL] or [SIMPLE].
[ERROR]:  An E-mail message is sent when an error 
occurred in the self-diagnosis.
[LAMP1 RUNTIME]:  An E-mail message is sent when the remaining 
lamp on time for the lamp 1 has reached the 
value set at the right field.
[LAMP2 RUNTIME]:  An E-mail message is sent when the remaining 
lamp on time for the lamp 2 has reached the 
value set at the right field.
[LAMP3 RUNTIME]:  An E-mail message is sent when the remaining 
lamp on time for the lamp 3 has reached the 
value set at the right field.
[LAMP4 RUNTIME]:  An E-mail message is sent when the remaining 
lamp on time for the lamp 4 has reached the 
value set at the right field.
[INTAKE AIR TEMPERATURE]:  An E-mail message is sent when the air intake 
temperature has reached the value set at the 
above field.
[PERIODIC REPORT]:  Place a check mark on this when E-mail is to be 
sent periodically.
It will be sent on the days and time with the check 
mark.
Note
 zSet each item of [LAMP1 RUNTIME] to [LAMP4 RUNTIME] to 500 hours or less when using the optional 
accessory replacement lamp unit (for portrait mode) (Model No.: ET
-LAD510P

 (1 pc), ET-LAD510PF (4 pcs)). 
						

							[NETWORK] menu
140 - ENGLISH
Settings
▶■[E-mail set up] page (continued)
(3)
(2)
(1)
(1) [E-MAIL ADDRESS 2]
Enter the E-mail address to be sent when two E-mail 
addresses are to be used.
Leave it blank when two E-mail addresses are not to 
be used.
(2) Settings of the conditions to send E-mail Select the conditions to send E-mail to the second 
E-mail address.
[MAIL CONTENTS]: Select either [NORMAL] or [SIMPLE].
[ERROR]:  An E-mail message is sent when an error 
occurred in the self-diagnosis.
[LAMP1 RUNTIME]:  An E-mail message is sent when the remaining 
lamp on time for the lamp 1 has reached the 
value set at the right field.
[LAMP2 RUNTIME]:  An E-mail message is sent when the remaining 
lamp on time for the lamp 2 has reached the 
value set at the right field.
[LAMP3 RUNTIME]:  An E-mail message is sent when the remaining 
lamp on time for the lamp 3 has reached the 
value set at the right field.
[LAMP4 RUNTIME]:  An E-mail message is sent when the remaining 
lamp on time for the lamp 4 has reached the 
value set at the right field.
[INTAKE AIR TEMPERATURE]:  An E-mail message is sent when the air intake 
temperature has reached the value set at the 
above field.
[PERIODIC REPORT]:  Place a check mark on this when E-mail is to be 
sent periodically.
It will be sent on the days and time with the check 
mark.
(3) [Submit] Update the settings.
Note
 zSet each item of [LAMP1 RUNTIME] to [LAMP4 RUNTIME] to 500 hours or less when using the optional 
accessory replacement lamp unit (for portrait mode) (Model No.: ET
-LAD510P

 (1 pc), ET-LAD510PF (4 pcs)).