Panasonic Projector PT-DW17KU User Manual

							Technical information
ENGLISH - 161
Appendix
Technical information
PJLink protocol
The network function of this projector supports the PJLink class 1, and the PJLink protocol can be used to 
perform projector setting and projector status query operations from a computer.
▶■Control commands
The following table lists the PJLink protocol commands that can be used to control the projector
.
CommandControl detailsRemark
POWR Power supply control Parameters
0 = Standby
1 = Power on
POWR? Power supply status query Parameters
0 = Standby
2 = Preparing to switch off 
the projector
1 = Power on
3 = Warm-up in progress
INPT Input selection Parameters
11=RGB1
31=DVI-D
12=RGB2
32=HDMI21=VIDEO
33=SDI 1 (only for PT-DZ21KU, PT-DS20KU)
34=SDI 2 (only for PT-DZ21KU, PT-DS20KU)
INPT? Input selection query
AVMT Shutter control
Parameters
30 = shutter function off (picture mute canceled)
31 = shutter function on (picture mute)
AVMT? Shutter status query
ERST? Error status query Parameters
1st byte: Indicates fan errors, range 0 - 2
2nd byte: Indicates lamp errors, range 0 - 2
3rd byte: Indicates temperature errors, range 0 - 2
4th byte: Fixed to 0
5th byte: Indicates filter errors, range 0 - 2
6th byte: Indicates other errors, range 0 - 2
Definitions for each value from 0 to 2 are as follows
0 = No error is detected 1 = Warning  2 = Error
LAMP? Lamp status query Parameters
1st digits (1 - 5 digits): Lamp 1 cumulative operating time
2nd digit: 0 = Lamp 1 off, 1 = Lamp 1 on
3rd digits (1 - 5 digits): Lamp 2 cumulative operating time
4th digit: 0 = Lamp 2 off, 1 = Lamp 2 on
5th digits (1 - 5 digits): Lamp 3 cumulative operating time
6th digit: 0 = Lamp 3 off, 1 = Lamp 3 on
7th digits (1 - 5 digits): Lamp 4 cumulative operating time
8th digit: 0 = Lamp 4 off, 1 = Lamp 4 on
INST? Input selection list query Parameters are returned with the following values.
“11 12 21 31 32” (only for PT-DW17KU)
“11 12 21 31 32 33 34” (only for PT-DZ21KU, PT-DS20KU)
NAME? Projector name query Returns the name set in [PROJECTOR NAME] of [NETWORK 
SETUP].
INF1? Manufacturer name query Returns “Panasonic”.
INF2? Model name query Returns “DZ21KU”, “DS20KU”, “DW17KU”.
INF0? Other information queries Returns information such as version number.
CLSS? Class information query Returns “1”. 
						

							Technical information
162 - ENGLISH
Appendix
▶■PJLink security authentication
The password used for PJLink is the same as that of the password set for W
eb control.
When using the projector without security authentication, do not set a password for W eb control.
▶zFor specifications regarding PJLink, refer to the Japan Business Machine and Information System 
Industries 

Association website.
URL http://pjlink.jbmia.or.jp/english/
Using Art-Net function
The network function of the projector supports the Art-Net function. Using the Art-Net protocol, you can control the 
projector settings with the DMX controller and application software.
▶■ Channel definition
The following table lists the channel definitions used for controlling the projector with the 
Art-Net function.
Channel Control detailsPerformance Parameter Remark
1 Shutter control SHUTTER:OPEN 0-63
No operation
64-191
SHUTTER:CLOSE 192-255
2 Input selection No operation
0-7
RGB1 8-15
RGB2 16-23
VIDEO 24-31
DVI
- D32-39
HDMI 40-47
SDI 1 48-55
(Only for 
PT-DZ21KU/PT-DS20KU)
SDI 2 56-63
No operation 64-127
Execute P IN P, USER1 128-135
Execute P IN P, USER2 136-143
Execute P IN P, USER3 144-151
No operation 152-255
3 Lens function select No operation
0-15
Lens H shift 16-31
Operate together with “Lens 
adjustment” of the channel 4.
Lens V shift
32-47
Lens focus 48-63
Lens zoom 64-79
Move to the home position 80-95 Operate together with 
“Command performance 
execute” of the channel 4.
No operation 96-255 
						

							Technical information
ENGLISH - 163
Appendix
Channel Control detailsPerformance Parameter Remark
4 Lens control Lens 
adjustment
(
-) High 
speed 0-31
(
-) Low 
speed 32-63
(
-) Fine 
adjustment 64-95
Adjustment stop 96-127
Lens 
adjustment (+) Fine 
adjustment
128-159
(+) Low 
speed 160-191
(+) High 
speed 192-223
Command performance 
execute 224-255
5 Power supply control Standby
0-63
No operation 64-191
Power on 192-255
6 Light volume adjustment 100
 
% 0
Can be set in 256 steps 
between 100 % and 0 %.
…
…
0
 
% 255
7 Lock Operation not available 0-127 When “Operation not 
available” is set, operations 
of all channels become 
unacceptable.
Operation available 128-255
8 Fade-in time setting 0.0s
0-15
Operate together with channel 
1.
0.5s
16-31
1.0s 32-47
1.5s 48-63
2.0s 64-79
2.5s 80-95
3.0s 96-111
3.5s 112-127
4.0s 128-143
5.0s 144-159
7.0s 160-175
10.0s 176-191
No operation 192-255 
						

							Technical information
164 - ENGLISH
Appendix
Channel Control detailsPerformance Parameter Remark
9 Fade-out time setting 0.0s
0-15
Operate together with channel 
1.
0.5s
16-31
1.0s 32-47
1.5s 48-63
2.0s 64-79
2.5s 80-95
3.0s 96-111
3.5s 112-127
4.0s 128-143
5.0s 144-159
7.0s 160-175
10.0s 176-191
No operation 192-255
10 Custom masking OFF
0-31
To use this function, the 
optional upgrade kit (Model 
No.: ET-UK20) is required.
PC-1
32-63
PC-2 64-95
PC-3 96-127
No operation 128-255
11 GEOMETRY OFF
0-15
To use PC-1, PC-2, or PC-
3, the optional upgrade kit 
(Model No.: ET-UK20) is 
required.
KEYSTONE
16-31
CURVED 32-47
PC-1 48-63
PC-2 64-79
PC-3 80-95
CORNER CORRECTION 96-111
No operation 112-255
Note
 z If the projector is operated with the remote control or on the control panel, or by the control command while 
controlling the projector by using the 

Art-Net function, the setting of the DMX controller and the computer 
application may be different from the projector status. In that case, set the “Lock” setting of the channel 7 to 
“Operation not available” and then reset to “Operation available”.  The controls of all channels become reflected 
to the projector. 
						

							Technical information
ENGLISH - 165
Appendix
Control commands via LAN
▶■When W eb control administrator rights password is set (Protect mode)
▶z
Connecting
1)  
Obtain the IP
  address and port number (Initial setting value = 1024) of the projector 
and request for a connection to the projector.
You can obtain both the IP address and the port number from the menu screen of the projector.
IP address Obtain from the main menu → [NETWORK] → [NETWORK STATUS]
Port number Obtain from the main menu → [NETWORK] → [NETWORK CONTROL] → [COMMAND 
PORT]
2) Check the response from the projector
Response data
Data section Blank Mode Blank Random number section Termination 
symbol
“NTCONTROL” (ASCII string) ‘ ’
0x20 ‘1’
0x31 ‘ ’
0x20 “zzzzzzzz”
(ASCII code hexadecimal  number) (CR)
0x0d
9 bytes 1 byte 1 byte 1 byte 8 bytes1 byte
Mode: 1 = Protect mode
3) Generate a 32-byte hash value from the following data using MD5 algorithm.
“xxxxxx:yyyyy:zzzzzzzz”
xxxxxx Administrator rights user name for Web control (default user name is “admin1”)
yyyyy Password of above administrator rights user (default password is “panasonic”)
zzzzzzzz 8-byte random number obtained in Step  2)
▶zCommand transmission method
Transmit using the following command formats.
Transmitted data
Header
Data sectionTermination 
symbol
Hash value
(“Connecting” (
 page 165)) ‘0’
0x30 ‘0’
0x30 Control command
(ASCII string) (CR)
0x0d
32 bytes 1 byte 1 byte Undefined length1 byte
Received data
Header Data sectionTermination 
symbol
‘0’
0x30 ‘0’
0x30 Control command
(ASCII string) (CR)
0x0d
1 byte 1 byteUndefined length 1 byte
Error response
Error message Termination symbol
“ERR1”
 
Undefined control command
“ERR2”

 
Out of parameter range
“ERR3”

 
Busy state or no-acceptable period
“ERR4”

 
T

imeout or no-acceptable period
“ERR5”
 
W

rong data length
“ERRA”
 
Password mismatch (CR)
0x0d
4 bytes 1 byte 
						

							Technical information
166 - ENGLISH
Appendix
▶■When W eb control administrator rights password is not set (Non-protect 
mode)
▶z Connecting
1)  
Obtain the IP
  address and port number (Initial set value = 1024) of the projector and 
request for a connection to the projector.
You can obtain both the IP address and the port number from the menu screen of the projector.
IP address Obtain from the main menu → [NETWORK] → [NETWORK STATUS]
Port number Obtain from the main menu → [NETWORK] → [NETWORK CONTROL] → [COMMAND 
PORT]
2) Check the response from the projector
Response data
Data section
BlankModeTermination 
symbol
“NTCONTROL” (ASCII string) ‘ ’
0x20 ‘0’
0x30 (CR)
0x0d
9 bytes 1 byte1 byte1 byte
Mode: 0 = Non-protect mode
▶z Command transmission method
Transmit using the following command formats.
Transmitted data
Header
Data sectionTermination 
symbol
‘0’
0x30 ‘0’
0x30 Control command
(ASCII string) (CR)
0x0d
1 byte 1 byteUndefined length 1 byte
Received data
Header Data sectionTermination 
symbol
‘0’
0x30 ‘0’
0x30 Control command
(ASCII string) (CR)
0x0d
1 byte 1 byteUndefined length 1 byte
Error response
Error message Termination symbol
“ERR1”
 
Undefined control command
“ERR2”

 
Out of parameter range
“ERR3”

 
Busy state or no-acceptable period
“ERR4”

 
T

imeout or no-acceptable period
“ERR5”
 
W

rong data length
“ERRA”
 
Password mismatch (CR)
0x0d
4 bytes 1 byte 
						

							Technical information
ENGLISH - 167
Appendix
/ terminal
The / terminal of the projector conforms with RS-232C so that the projector can be 
connected to and controlled from a computer.
▶■Connection
When using 1 unit
When using multipl\
e units
Connecting termina\Dls on projector 1Connecting termina\Dls on projector 2
 D\fSub \b\fpin 
(female)  D\fSub \b\fpin 
(male)  D\fSub \b\fpin 
(female)  D\fSub \b\fpin 
(male)Connecting termina\Dls on this device
Computer Computer D\fSub \b\fpin (female)
 D\fSub \b\fpin (male)  D\fSub \b\fpin 
(female)  D\fSub \b\fpin 
(male)
 D\fSub \b\fpin (male)
Communication cable\D
Communication cable\D Communication cable\D
▶■Pin assignments and signal names
D-Sub 9-pin (female)
Outside view Pin No. Signal name
Details
(9) (6)
(5) (1)
(1)
— NC
(2) TXD Transmitted data
(3) RXD Received data
(4) — Connected internally
(5) GND Earth
(6) — NC
(7) CTS
Connected internally
(8) RTS
(9) — NC
D-Sub 9-pin (male)
Outside view Pin No. Signal name
Details
(6) (9)
(1) (5)
(1)
— NC
(2) RXD Received data
(3) TXD Transmitted data
(4) — NC
(5) GND Earth
(6) — NC
(7) RTS
Connected internally
(8) CTS
(9) — NC
▶■Communication conditions
Signal level
RS-232C-compliant Character length8 bits
Sync. method Asynchronous Stop bit1 bit
Baud rate 9
  600 bps X parameterNone
Parity None S parameterNone         
						

							Technical information
168 - ENGLISH
Appendix
▶■Basic format
Transmission from the computer starts with STX, then the ID, command, parameter, and ETX are sent in this 
order. Add parameters according to the details of control.
(2 bytes)
2 ID characters (2\o bytes)
Semico\fon (1 byte)
Co\fon\b1 
9Ô1 byte
9Õ3 command 
characters (3 byte\os)Parameter 
(undefined \fength)End
(1 byte)
Start
(1 byte)ID designate
ZZ, 01 to 64 and 0A t\oo 0Z
*1: When transmitting a command which does not need a parameter , a colon (:) is not necessary.
▶■Basic format (with subcommands)
Parameter (6 bytes\“)*1
Symbol “\f” or “-” (1\“ byte) an\b setting 
or a\bjustment value\“ (5 bytes)
Operation (1 byte)
*1
“=” (Set the value \“specifie\b using param\“eter)
Sub comman\b 
(5 bytes)
Same as the basic \“format
*1: When transmitting a command which does not need a parameter , the operation (E ) and parameter are not necessary.
Attention
 zIf a command is transmitted after the lamp starts illuminating, there may be a delay in response or the 
command may not be executed. 

Try sending or receiving any command after 60 seconds.
 zWhen transmitting multiple commands, be sure to wait until 0.5 seconds has elapsed after receiving the 
response from the projector before sending the next command.
Note
 z If a command cannot be executed, a “ER401” response is sent from the projector to the computer
.
 zIf an invalid parameter is sent, a “ER402” response is sent from the projector to the computer
.
 zID transmission in RS-232C supports ZZ (ALL) and 01 to 64, as well as 0A
 to 0Z groups.
 zIf a command is sent with a specified ID, a response will be sent to the computer only in the following cases.
–

▶
It matches the projector ID
–

▶
ID setting is set to 
 ALL and [RESPONSE(ID ALL)] is [ON]
–
▶
ID setting is set to GROUP
  and [RESPONSE(ID GROUP)] is [ON]
 zSTX and ETX are character codes. STX shown in hexadecimal is 02, and ETX shown in hexadecimal is 03. 
						

							Technical information
ENGLISH - 169
Appendix
▶■When multiple projectors are controlled
▶z
When multiple projectors are all controlled
When controlling multiple projectors together via RS-232C, perform the following settings.
1) Set a different ID for each projector
2)  
Set [RESPONSE(ID 
 ALL)] to [ON] in only one projector
3)
 
Set [RESPONSE(ID 
 ALL)] to [OFF] for all other projectors set in Step 2)
▶zWhen multiple projectors are all controlled by group unit
When controlling multiple projectors by group unit via RS-232C, perform the following settings.
1) Set a different ID for each projector
2)  
Set [RESPONSE(ID GROUP)] to [ON] in only one projector
3)

 
Set [RESPONSE(ID GROUP)] to [OFF] for all other projectors set in Step 2)
Note
 z There will be no response if 2 or more projectors have [RESPONSE(ID 
ALL)] set to [ON].
 zT

here will be no response if 2 or more projectors of the same group have [RESPONSE(ID GROUP)] set to [ON].
 zWhen setting multiple groups, set [RESPONSE(ID 

ALL)] to [ON] in only one projector in each group.
▶■Cable specification
▶z
When connected to a computer▶zWhen multiple projectors are connected
Projector
( 
terminal)
1 NC NC 1
Computer
(DTE 
specifications) Projector 1
( 
terminal)
1 NC NC 1
Projector 2
( 
terminal)
2
2 22
3 3 33
4 NC NC 4 4 NC NC 4
5 5 55
6 NC NC 6 6 NC NC 6
7 7 77
8 8 88
9 NC NC 9 9 NC NC 9 
						

							Technical information
170 - ENGLISH
Appendix
▶■Control command
The following table lists the commands that can be used to control the projector using a computer
.
▶zProjector control command
CommandDetails
Remarks (parameters)
PON Power on To check if the power is on, use the “Power query” command.
POF Power standby
QPW Power query 000 = Standby 001 = Power on
IIS Switching the input 
signal VID=VIDEO RG1 = RGB1 RG2 = RGB2 DVI=DVI-D HD1 = HDMI
SD1 = SDI 1 (only for PT-DZ21KU, PT-DS20KU)
SD2 = SDI 2 (only for PT-DZ21KU, PT-DS20KU)
QSL Query for active 
lamp selection 0 = Quad
4 = Lamp 1/2/3
8 = Triple 
*1
12 = Lamp 41 = Lamp 1/4
5 = Lamp 1/2/4
9 = Lamp 1
13 = Single *1
2 = Lamp 2/3
6 = Lamp 1/3/4
10 = Lamp 2
3 = Dual *1
7 = Lamp 2/3/4
11 = Lamp 3
LPM Lamp mode 0 = Quad
4 = Lamp 1/2/3
8 = Triple 
*1
12 = Lamp 41 = Lamp 1/4
5 = Lamp 1/2/4
9 = Lamp 1
13 = Single *1
2 = Lamp 2/3
6 = Lamp 1/3/4
10 = Lamp 2
3 = Dual *1
7 = Lamp 2/3/4
11 = Lamp 3
Q$L Lamp cumulative 
operating time query 1 = Lamp 1 2 = Lamp 2 3 = Lamp 3 4 = Lamp 4
Response is 0000 to 2000
OSH Shutter 0 = End1 = Execute
QSH Shutter status query 0 = End 1 = Execute
VSE Aspect switching 0 = Standard/ VID auto
1=4:32=16:95 = THROUGH
6 = HV FIT 9 = H FIT 10 = V FIT
QSE Aspect setting query 0 = Standard/ VID auto
1=4:32=16:95 = THROUGH
6 = HV FIT 9 = H FIT 10 = V FIT
OPP P IN P execute 0 = Off 1 = User 1 2 = User 2 3 = User 3
QPP P IN P setting query 0 = Off 1 = User 1 2 = User 2 3 = User 3
OCS Sub memory 
switching 01 to 96 = Sub memory number
QSB Sub memory status 
query 01 to 96 = Sub memory number
*1:
 
Used from the lamp with the shortest cumulative operating time.
▶z Projector control command (with sub command)
Command
Sub command Details Notes
VXX RYCI1  RGB1 input setting +00000=RGB/YP
BPR, +00001 = Y/C
▶zLens control command
Command
Sub command Details Notes
VXX LNSI2 Lens H shift
+00000 = Fine tuning 1+, +00001 = Fine tuning 1–, 
+00100 = Fine tuning 2+, +00101 = Fine tuning 2–, 
+00200 = Coarse adjustment+, +00201 = Coarse 
adjustment–
VXX
LNSI3 Lens V shift
VXX LNSI4 Lens focus
VXX LNSI5 Lens zoom