Panasonic Projector PT-LW271U User Manual

							Setting
ENGLISH - 41
Settings
Remote ID
When you use the system with multiple projectors, 
you can operate all the projectors simultaneously or 
each projector individually using single remote control, 
if a unique ID number is assigned to each projector.
There are 7 different remote control IDs: [All], 
[ID1]~[ID6].
Press ▲▼ to select [Remote ID].1 ) 
Press ► to display the setting dialog 2 ) 
box.
Press ◄► to select the desired item.3 ) 
Attention
When operating the projector under [All] code, you can  z
operate several projectors at the same time.
If you want to control the projector with a specified  z
remote control ID, make sure the remote control ID on 
the remote control fit to the remote control ID on the 
projector. (Æpage 20)
Startup Logo
Set this function to display the Panasonic logo when 
the projector is turning on.
Press ▲▼ to select [Startup Logo].1 ) 
Press ► to display the setting dialog 2 ) 
box.
Press ◄► to switch [On]/[Off].3 ) 
OnThe logo will display when the 
projector is turning on.
OffThe logo will not display when the 
projector is turning on.
UART Mode
Use this function to select RS-232 or LAN function.
Press ▲▼ to select [UART Mode].1 ) 
Press ► to display the setting dialog 2 ) 
box.
Press ◄► to select the desired item.3 ) 
LANControl the projector via  
terminal.
RS-232Control the projector via  terminal.
Note
When [RS-232] is selected, [LAN(Standby)] and the  z
items of [LAN] are disable.
LAN (Standby)
Use this function to use network function when the 
projector is in standby mode.
Press ▲▼ to select [LAN (Standby)].1 ) 
Press ► to display the setting dialog 2 ) 
box.
Press ◄► to switch [On]/[Off].3 ) 
OnLAN function is available when in 
standby mode.
OffLAN function is unavailable when 
in standby mode.
Reset
Return all data that has been set in the [Setting] menu 
to the factory defaults.
Press ▲▼ to select [Reset].1 ) 
Press ► to display the setting dialog 2 ) 
box.
Press ▲▼ to select [Yes].3 ) 
Press ► to execute.4 ) 
Note
Lamp used time has been set by user in the [Security] z 
menu will not be reset. 
						

							Audio
42 - ENGLISH
Settings
Audio
Select [Audio] from the Main Menu (see “How 
to operate menu” on page 33) and then select 
the item from the Sub Menu.
Mute
Temporarily turn off the sound.
Press ▲▼ to select [Mute].1 ) 
Press ► to display the setting dialog 2 ) 
box.
Press ◄► to switch [On]/[Off].3 ) 
OnMute.
OffOutput audio.
Press z  button on the remote control 
can also turn on/off the sound.
Volume
Adjust the volume.
Press ▲▼ to select [Volume].1 ) 
Press ► to display the adjustment 2 ) 
dialog box.
Press ◄► to adjust the volume.3 ) 
OperationAdjustmentAdjustment 
range
Press ►.Turn up the volumeMaximum value 32
Press ◄.Turn down the 
volumeMinimum value 0
You can also press the  buttons  z
on the remote control or on the control panel.
In Standby Mode (Audio)
This function is used to switch the output audio signal 
from the  terminal On/Off at 
standby mode.
Press ▲▼ to select [In Standby Mode 1 ) 
(Audio)].
Press ► to display the adjustment 2 ) 
dialog box.
Press ◄► to switch [On]/[Off].3 ) 
On
Output the audio signal from the 
 terminal 
when in Standby mode.
Off
Mute the audio signal from the 
 terminal 
when in Standby mode.
Note
When setting the [In Standby Mode (Audio)] function to  z
[On] and in Standby mode status, the connected audio 
signal to  terminal can be output from the 
 terminal. The audio signal 
output level is fixed and cannot be adjusted. 
						

							ENGLISH - 43
Settings
Select [Options] from the Main Menu (see “How 
to operate menu” on page 33) and then select 
the item from the Sub Menu.
Auto Source
Set the automatic signal search function  when power 
on or the source of the signal being received is lost.
Press ▲▼ to select [Auto Source].1 ) 
Press ► to display the setting dialog box.2 ) 
Press ◄► to switch [On]/[Off].3 ) 
On
It will automatically search and 
display the signal sources marked 
in the [Input] when power on or the 
source of the signal being received 
is lost.
OffWhen the source of the signal being received is lost, it will not search other sources.
Search and display order: [Computer 1]  z 
[Computer 2]  [HDMI]  [Video]  
[Computer 1] .
Input
Set the automatic search signal source for [Auto 
Source].
Press ▲▼ to select [Input].1 ) 
Press ► to display the setting dialog box.2 ) 
The [Input] menu dialog box is displayed. z
Press ▲▼ to select the input you want 3 ) 
to search and press ►.
The input with a check mark will be able to be  z
searched when [Auto Source] is set to [On]. 
To remove the check mark, choose the desired  z
item and press ►.
Auto Power Off (Min)
Set the time to automatically turn off the projector  
when there is no signal input.
Press ▲▼ to select [Auto Power Off 1 ) 
(Min)].
Press ► to display the adjustment 2 ) 
dialog box.
Press ◄► to adjust off timer (min).3 ) 
When this function is set to [0 (min)], it is disable. z
You can set the time in 5 minutes intervals and  z
the longest set time is 120 minutes.
Note
60 seconds before the auto power off, the countdown  z
screen will appear. During countdown, the screen will 
disappear if there is signal input or operation to the 
projector.
Lamp Settings
Displays and sets detail of the lamp settings.
Press ▲▼ to select [Lamp Settings].1 ) 
Press ► to display the setting dialog 2 ) 
box.
Lamp Hours Used (Normal) J
Displays the used lamp hours under [Normal]  z
lamp power mode.
Lamp Hours Used (ECO) J
Displays the used lamp hours (in real time)  z
under [Auto] / [ECO1]([ECO]) / [ECO2] lamp 
power mode. The time is displayed as the sum 
of the time under each setting of [Auto], [ECO1]
([ECO]) and [ECO2] lamp power mode.
Lamp Life Reminder J
Press ▲▼ to select [Lamp Life 1 ) 
Reminder].
Press ► to display the setting dialog box.2 ) 
Press ◄► to switch [On]/[Off].3 ) 
OnDisplays the lamp warning 
message. (Æpage 55)
OffThe warning lamp message will 
not be displayed.
Options 
						

							Options
44 - ENGLISH
Settings
Attention
If [Lamp Life Reminder] is set to [Off], the lamp warning 
message will not be displayed when the lamp used time 
reaches the end of lamp life. In this case, please check the 
lamp life with the values at the [Lamp Hours Used (Normal)] 
and [Lamp Hours Used (ECO)].
Lamp Power Mode J
Selects desired lamp power mode under  z
different situations.
Press ▲▼ to select [Lamp Power Mode].1 ) 
Press ► to display the setting dialog box.2 ) 
Press ◄► to select the desired item.3 ) 
NormalNormal brightness.
Auto
The brightness level of the content is 
automatically detected to significantly 
reduced lamp power consumption 
during periods of inactivity.
ECO1 / 
ECO *1
Lower brightness reduces the lamp 
power consumption and extends the 
lamp life.
ECO2*1Lowest brightness reduces the lamp 
power consumption and extends the 
lamp life.
*1: Normal / Auto / ECO1 / ECO2 for PT-LX351U.
     Normal / Auto / ECO for PT-LW321U / PT-   
     LW271U / PT-LX321U / PT-LX271U.
Note
When there is no signal for more than 5 minutes, the  z
lamp power will be decreased automatically for power 
saving.
Clear Lamp Hours J
Reset the lamp usage time after replacing the  z
lamp unit. 
Press ▲▼ to select [Clear Lamp Hours].1 ) 
Press ► to display the setting dialog box.2 ) 
Press 3 ) ▲▼ to switch [Yes]/[No]. 
Press ► to execute.4 )  
High Altitude
Set to [On] when the projector is used at elevation 
approx. 1 000 m (3 300 ft) and approx. 3 000 m  
(10 000 ft).
Press ▲▼ to select [High Altitude].1 ) 
Press ► to display the adjustment 2 ) 
dialog box.
Press ◄► to switch [On]/[Off].3 ) 
On
For the elevation approx. 1 000 m  
(3 300 ft) and approx. 3 000 m  
(10 000 ft).
OffFor the elevation below approx.  
1 000 m (3 300 ft).
Note
When [On] is selected, the speed and the noise of the  z
fan will increase.
Dust Filter Reminder 
Set the cleaning cycle of the filters and reset the use 
time of the filters.
Press ▲▼ to select [Dust Filter 1 ) 
Reminder].
Press ► to display the setting dialog box. 2 ) 
Filters Remind (Hour) J
Set the timer to display the Dust Filter Reminder  z
message (Æpage 53).
Press ▲▼ to select [Filters Remind 1 ) 
(Hour)].
Press ► to display the adjustment 2 ) 
dialog box.
Press ◄► to set the time.3 ) 
The factory default is 0 hour. z
You can set the time in 50 hours intervals and  z
the longest set time is 1 000 hours.
Cleaning up Reminder J
Reset the air filter used time to zero. z
Reset the air filter hour counter after cleaning  z
or replacing the dust filter. 
Press ▲▼ to select [Cleaning up 1 ) 
Reminder].
Press ► to display the setting dialog box.2 ) 
Press ▲▼ to switch [Yes]/[No].3 ) 
Press ► to execute.4 ) 
Note
It is recommended to clean the air filters regularly every  z
500 hours of usage.
Information
Displays the input signal source and setting state 
information of the projector.
Press ▲▼ to select [Information].1 ) 
Press ► to display the information 2 ) 
dialog box.
Displays [Model Name], [Source], [Resolution],  z
[Software Version], [Color Space] and [Aspect 
Ratio]. 
						

							LAN
ENGLISH - 45
Settings
Select [LAN] from the Main Menu (see “How to 
operate menu” on page 33) and then select the 
item from the Sub Menu.
Note
The following settings are set before the projector leaves  z
the factory.
DHCPOff
IP Address1 9 2 .1 6 8 .1 0 .1 0 0
Subnet Mask255.255.255.0
Gateway1 9 2 .1 6 8 .1 0 .1
DNS0.0.0.0
If you want to use a DHCP server, please make sure that  z
the DHCP server is enabled.
For more information about the IP Address, Subnet  z
Mask, Gateway, and DNS, please contact your network 
administrator.
DHCP
Set whether to use DHCP server.
Press ▲▼ to select [DHCP].1 ) 
Press ► to display the setting dialog 2 ) 
box.
Press ▲▼ to switch [On]/[Off].3 ) 
Press  button to exit the switching and  z
go back to the previous menu.
Press ► to confirm.4 ) 
After selecting [On], the message about LAN  z
restarting will be displayed. The setting of 
DHCP finishes when the message disappears.
Press  to exit. 5 ) 
 
 
OnThe projector will acquire the IP 
address automatically.
Off
User must set the [IP Address], 
[Subnet Mask], [Gateway] and 
[DNS] manually.
IP Address
Select an IP Address of projector connected to 
network.
Press ▲▼ to select [IP Address].1 ) 
Press ► to display the setting dialog 2 ) 
box.
Press ▲▼◄► to input digit numbers.3 ) 
Press  to exit.4 ) 
Subnet Mask
Select Subnet Mask of projector for network 
connection.
Press ▲▼ to select [Subnet Mask].1 ) 
Press ► to display the setting dialog 2 ) 
box.
Press ▲▼◄► to input digit numbers.3 ) 
Press  to exit.4 ) 
Gateway
Select Gateway of projector for network connection.
Press ▲▼ to select [Gateway].1 ) 
Press ► to display the setting dialog box.2 ) 
Press ▲▼◄► to input digit numbers.3 ) 
Press  to exit.4 ) 
DNS
Select DNS of projector for network connection.
Press ▲▼ to select [DNS].1 ) 
Press ► to display the setting dialog 2 ) 
box.
Press ▲▼◄► to input digit numbers.3 ) 
Press  to exit. 4 ) 
 
 
 
 
 
LAN 
						

							LAN
46 - ENGLISH
Settings
Store
Save the network settings.
Press ▲▼ to select [Store].1 ) 
Press ► to display the setting dialog 2 ) 
box.
Press ▲▼ to switch [Yes]/[No].3 ) 
Press ► to execute.4 ) 
Select [Yes] to start executing and the resetting  z
message appears. The store procedure finishes 
when the message disappears.
Reset
Return all data that has been set in the [LAN] menu to 
the factory defaults.
Press ▲▼ to select [Reset].1 ) 
Press ► to display the setting dialog 2 ) 
box.
Press ▲▼ to switch [Yes]/[No].3 ) 
Press ► to execute.4 ) 
Select [Yes] to start executing and the resetting  z
message appears. The reset procedure finishes 
when the message disappears. 
						

							LAN
ENGLISH - 47
Settings
The projector has a network function, and the following operations are a\
vailable from the computer using the web 
browser control.
Setting and adjustment of the projector. z
Display of the projector status. z
Transmission of an E-mail message when there is a problem with the projec\
tor. z
This projector supports "Crestron RoomView" and the following application software from Crestron company. 
(Æpage 51)
RoomView Express z
Attention
Connects LAN to indoor equipment. z
Set the [UART Mode] in the [Setting] menu to [LAN] before controlling the projector via  terminal. z
Note
A LAN cable is required to use the wired LAN function. z
Computer
Projector
LAN cable (straight) LAN cable (straight)
Hub
Connect to Network
A Web browser is required to use this function. Confirm that the Web browser can be used beforehand.  z
Compatible OS : Windows XP/Windows Vista/Windows 7, Mac OS X v10.4/v10.5/v10.6/v10.7  
Compatible Web Browser : Internet Explorer 7.0/8.0/9.0, Safari 4.0/5.0 (Mac OS)
Communication with an E-mail server is required to use the E-mail function. Confirm that the E-mail can be  z
used beforehand.
Use shielded LAN cable (STP cable) that is compatible with category 5 or above. z
Use a LAN cable with length of 100 m or shorter. z
Name and function of network function parts  J
(1)     
ACT lamp (yellow)
 Blinks when the LAN network function acts 
normal.
(2)   LAN terminal (10BASE-T/100BASE-TX)
Used to connect the LAN cable here.
(3)   LINK lamp (green)
Lights on when connected to network.
(1)(2)(3) 
						

							LAN
48 - ENGLISH
Settings
Computer operation via network
Connection can be made with wired LAN. However, confirm to your system administrator on network settings 
before changing any settings.
Turn on the computer.1 ) 
Make the network setting according to your system administrator.2 ) 
If the projector settings are the default settings (Æpage 45), the computer can be used with the following 
network settings.
DHCPOff
IP Address1 9 2 .1 6 8 .1 0 .1 0 1
Subnet Mask255.255.255.0
Gateway1 9 2 .1 6 8 .1 0 .1
DNSNONE
Web Management
Start the WEB browser of the computer.1 ) 
URL input box of the WEB browser and the IP Address setting of the projector. 2 ) 
Enter password.3 ) 
Input the administrator password. ( zÆpage 50) 
Click Login button.4 ) 
Display [Projector Information] page. z 
Select page menu on the left to display detail page. z
Note
 
For security reason, set an administrator password for the Web Management and restrict the users who can log in.  z
(Æpage 50)
Network connection will be disconnected when you cut off the power, such as unplug the power cord. When you want to  z
operate the WEB browser after reconnecting the power, please press [F5] on the keyboard to refresh your browser. 
						

							LAN
ENGLISH - 49
Settings
Main Menu description J
Projector Information J
Displays basic information of the projector.
 
 
 
LAN Setting J
Sets the LAN Setting of the projector and press [Save] to store settings.
 
 
Attention
For the security reason, do not enter any information that third party can recognize your location or name, in [Location] and  z
[Contact] columns.
(1)
(2)
(1) Projector Information
 Confirm Projector Information.
 Displays lamp use time [Lamp Hours] 
(corresponding value) and projector running hour 
[Operation Hours].
(2) Language
   Select Web Management display language (21 
languages).
Switches languages among English / German /  z
French / Italian / Spanish / Dutch / Portuguese 
/ Japanese / Traditional Chinese / Simplified 
Chinese / Korean / Russian / Polish / Swedish / 
Arabic / Turkish / Norwegian / Czech /  
Hungarian / Kazakh / Thai. 
The On-screen Menu of Language of the 
projector can not be changed by the Web 
management menu.
(1)
(2)
(1)   [Model Name] [Projector Name] [Location] 
[Contact]
 Enter projector basic information and press [Save].
(2)   [DHCP] [Manual]
   Select [DHCP] when the DHCP client function is 
enable.
   [IP Address] [Subnet Mask] [Gateway]   
  [DNS]
   When DHCP server is unavailable, please select 
[Manual] and enter [IP Address], [Subnet Mask], 
[Gateway] and [DNS].
(3)   [Crestron Control System Device]
   Enter [IP Address], [Device ID] and [Port] when 
Crestron RoomView is in use and press [Save].
(3)
(1)
(2)
(3)
(4)
(5)
(1) Projector Information
 Click this item and the [Projector Information] 
displays.
(2) LAN Setting 
 Click this item and the [LAN Setting] displays.
(3) Projector Status and Control
 Click this item and the [Projector Status and 
Control] displays.
(4) E-mail Setting 
 Click this item and the [E-mail Setting] displays.
(5) Security Setting 
 Click this item and the [Security Setting] displays. 
						

							LAN
50 - ENGLISH
Settings
Projector Status and Control J
Sets the projector status and adjusts Image and Audio controls.
E-mail Setting J
Sets E-mail Alert and SMTP Setting and Alert Condition of the projector and press [Save] to store settings.
Note
The E-mail function of this projector does not compatible  z
with the advanced SMTP server. 
Security Setting J
Sets a password for the administrator to manage the Web.
(1)
(2)
(3)
(1)
(1)  [Administrator]
 When set the password, click [Enable] and enter 
both of [New Password] and [Confirm Password] {4 
characters in single byte (0~9, A~Z, a~z)}, and then 
click [Submit].
(1)
(2)
(3)
(1)   [Projector Status]
 Confirm Projector Status.
 Press [Refresh] button to refresh.
 Press [Power ON] or [Power OFF] button to operate 
power status.
 Set the time for the projector to shut down 
automatically when there is no signal input in [Power 
Saving].
 Confirm the [Alert status] of abnormal conditions.
(2)   [Image Control]
   Adjust projector image.
   Use the [Auto Adjust] button to adjust image to the 
best position and size.
(3)   [Audio Control]
   Adjust projector volume.
(1)   [E-mail Alert]
 Click [Enable] when using the E-mail function.
 Login [TO], [CC], [From] of the E-mail address to 
enable the abnormal E-mail notification.
 {up to 40 characters in single byte (15+@+24)}
 You can enter [Subject] information such as the 
location of the projector that notifies the sender of the 
E-mail. (up to 30 characters in single byte )
(2)   [SMTP Setting]
   Login [Out going SMTP server]  
(up to 30 characters in single byte )
(3)   [Alert Condition]
  Login [Lamp warning], [Lamp life reminder], 
[Temperature warning] of the Alert Condition to 
enable the abnormal E-mail notification. (Æpage 60)