Panasonic Projector PT-VW535N User Manual

							About Wireless LANs
The advantage of a wireless LAN is that information can be exchanged between a PC or other such equipment and an 
access point using radio waves as long as you are within range for radio\
 transmissions.
On the other hand, because the radio waves can travel through obstacles (such as walls) and are available everywhere 
within a given range, problems of the type listed below may occur if security-related settings are not made. 
f A malicious third-part may intentionally intercept and monitor transmitted data including the content of e-mail and 
personal information such as your ID, password, and/or credit card numbers.
 
f A malicious third-party may access your personal or corporate network without authorization and engage in the 
following types of behavior.
Retrieve personal and/or secret information (information leak)
Spread false information by impersonating a particular person (spoofing)
Overwrite intercepted communications and issue false data (tampering)
Spread harmful software such as a computer virus and crash your data and/or system (system crash)
Since most wireless LAN adapters or access points are equipped with secu\
rity features to take care of these problems, 
you can reduce the possibility of these problems occurring when using th\
is product by making the appropriate security 
settings for the wireless LAN device.
Some wireless LAN devices may not be set for security immediately after \
purchase. To decrease the possibility of 
occurrence of security problems, before using any wireless LAN devices, be absolutely sure to make all security-related 
settings according to the instructions given in the operation manuals su\
pplied with them.
Depending on the specifications of the wireless LAN, a malicious third-party may be able to break security settings by 
special means.
Panasonic asks customers to thoroughly understand the risk of using this\
 product without making security settings, and 
recommends that the customer make security settings at their own discret\
ion and responsibility.
ENGLISH  -  21
Chapter 1   Preparation - Precautions for use  
						

							Accessories
Make sure the following accessories are provided with your projector. Numbers enclosed < > show the number of accessories.
Wireless remote control unit 
(N2QAYA000107)CD ROM 
(TXFQB02VLQ9)
Power cord 
(TXFSX02UXRZ)AAA/R03 or AAA/LR03 battery 
(for remote control unit)
 
(TXFSX02UYAZ)
String 
(for lens cap)
(6103504711)
(TXFSX02UFEZ)Lens cap  
(Attached to the projector at the time of purchase)
(TKKL5573)                          (TKKL5577)
(For PT-VZ575N)                        (For PT-VW535N and PT-VX605N)
                                
RGB signal cable 
(K1HY15YY0012)
Attention
 
f After unpacking the projector, discard the power cord cap and packaging material properly.
 
f Do not use the supplied power cord for devices other than this projector\
.
 
f For lost accessories, consult your dealer.
 
f Store small parts in an appropriate manner, and keep them away from young children.
Note
 
f The type and number of the power cord depend on the country in which you\
 purchased the product.
 
f The model numbers of accessories are subject to change without prior not\
ice.
22 -  ENGLISH
Chapter 1   Preparation - Precautions for use  
						

							Contents of the supplied CD-ROM
The contents of the supplied CD-ROM are as follow.
Instruction / list (PDF) Operating Instructions – Functional Manual
Operating Instructions – Multi Projector Monitoring & Control Software 
Operating Instructions – Logo Transfer Software
Operating Instructions – Wireless Manager ME6.2
List of Compatible Projector Models
This is a list of projectors that are com-
patible with the software contained in the 
CD-ROM and their restrictions.
Software license The open source software licenses that 
used in this projector are included in the 
PDF files.
Software Multi Projector Monitoring & Control 
Software (Windows)
This software allows you to monitor and 
control multiple projectors connected to 
the LAN.
Logo Transfer Software   
(Windows) This software allows you to transfer 
original images, such as company logos 
to be displayed when projection starts, to 
the projector.
Wireless Manager ME6.2  
 (Windows/Mac) This software allows you to send com
-
puter screen displays over wireless/wired 
LAN.
Optional accessories
Options Model No.
Ceiling Mount Bracket ET-PKL100H (for high ceilings) 
 
ET-PKL100S (for low ceilings)
ET-PKV400B (Projector Mount Bracket)
Replacement Lamp Unit ET-LAV400
Replacement Filter Unit ET-RFV400
Easy Wireless Stick*
1ET-UW100
Digital Interface Box ET-YFB100G
D-SUB - S Video conversion cable ET-ADSV
*1 : This product can be purchased in the U.S., Canada, Japan and the European Communities.
Note
 
f The model numbers of optional accessories are subject to change without \
prior notice.
ENGLISH  -  23
Chapter 1   Preparation - Precautions for use  
						

							About your projector
Remote control
2
3
4
5
6
7
89
10
11
12 14
15
16
17
18
19
20
21
22
23
24
26
13 1
25
27
28
r Front
r Bottom
r To p
1  Power button < v/b>
Sets the projector to the state where the projector is 
switched off (standby mode). Also starts projection when 
the power is switched off (standby mode).
2   button
Automatically adjusts the image display position while 
projecting the image.(
Æ page 46) In addition, it 
acts as  button when using the MEMORY 
VIEWER function. 
3   button
Displays or hides the main menu. (
Æ page 53)
4   button/ asq(VOL -) w(VOL+) buttons
Navigates the menu display. And use qw to adjust the 
volume level, use  as to page up or page down files 
such as PowerPoint
® through wireless manager.
5   button
Resets the content of the sub-menu to the factory 
default. (
Æ page 54)
6   button
Switches the MEMORY VIEWER signal to project. 
(
Æ page 48)
7   button
Switches the COMPUTER1 signal to project.
8   button
Switches the COMPUTER2 signal to project.
9   button
Switches the HDMI1 signal to project.
10   button
Used to mute the audio. (
Æ page 50)
11   buttons
Zoom in and out the images. (
Æ page 49)
12   button
Used to turn off the audio and video temporarily.
(
Æ page 50)
13   button
Sets the ID number of the remote control to use for a 
system using multiple projectors. (
Æ page 50) 14 
Remote control indicator
Flashes if any button in the remote control is pressed.
15   button
You can correct various types of distortion in a projected 
image.(
Æ page 46)
16   button
Return to the previous menu or cancel the setting.
17   button
Assigns a frequently used operation as a shortcut button.  
(
Æ page 47)
18   button
Switches the Panasonic APPLICATION signal to project. 
(
Æ page 48)
19   button
Switches the Miracast signal to project. (
Æ page 48)
20   button
Switches the VIDEO signal to project.
21   button 
Switches the DIGITAL LINK signal to project.
22   button
Switches the HDMI2 signal to project.
23   button
Pauses the projected image and mute the audio 
temporarily. (
Æ page 49)
24  Number buttons
Act as number buttons. Use these buttons when setting 
the remote control codes or entering the password.
25  button
Operate the P-TIMER function. (Æ page 50)
26  button
Used to simultaneously control all the projectors with one 
remote control for a system using multiple projectors.
(
Æ page 50)
27  Remote control signal emitters
28  This jack is not used for these projector models.
24 - ENGLISH
Chapter 1   Preparation - About your projector    
						

							Attention
 
f Do not drop the remote control.
 
f Avoid contact with liquids.
 
f Do not attempt to modify or disassemble the remote control.
 
f Please observe the following contents that are described on   
the back of the remote control unit (see the right picture).  
1. Do not use a new battery together with an old battery. 
2. Do not use unspecified batteries.  
3. Make sure the polarities (+ and -) are correct when inserting the batteries.
 
f In addition, please read the contents that are related to batteries in the "Read this first!".
Note
 
f The remote control can be used within a distance of about 7 m (22′1 1-5/8″) if pointed directly at the remote control signal 
receiver. The remote control can control at angles of up to ± 30 ° vertically and ± 30 ° horizontally, but the effective control 
range may be reduced.
 
f If there are any obstacles between the remote control and the remote con\
trol signal receiver, the remote control may not 
operate correctly.
 
f You can operate the projector by reflecting the remote control signal on the screen. The operating range may differ due to 
the loss of light caused by the properties of the screen.
 
f When the remote control signal receiver is lit with a fluorescent light or other strong light source, the projector may become 
inoperative. Set the projector as far from the luminous source as possib\
le.
Projector body
41
2 3
5 41213
6 6
66 78910 11
r Frontr Side
r Rear
 Projection direction
WARNING
Keep your hands and other objects away from the air 
exhaust port.
 
f Keep your hands and face away.
 
f Do not insert your fingers.
 
f Keep heat-sensitive objects away.
Heated air from the air exhaust port can cause burns, 
injury, or deformations.
1  Remote control signal receiver
2  Focus Lever
Adjusts the focus.
3 Zoom LeverAdjusts the zoom.
4 Adjustable feetAdjusts the projection angle.
5 Projection Lens
6  Air exhaust port
7  Speaker
8   terminal
Connects the supplied power cord.
9 Security slotThis security slot is compatible with the Kensington security  
cables.
10  Connecting terminals (Æ page 27)
11  Burglar hook port
Attaches a burglar prevention cable, etc.
12  Air filter coverThe air filter unit is inside.
13 Air intake port
1.请勿把旧电池和新电池一起使用。
2. 请勿使用不合规格的电池。
3. 确保电池安装正确。
原产地：中国
1.Do not use old battery with new one.
2.Do not use batteries other than the
   type specified.
3.Be sure the batteries are inserted properly.
Made in China
ENGLISH  -  25
Chapter 1   Preparation - About your projector  
						

							611 1415 16
 Projection direction
r Bottomr To p
14 
Control panel and Indicators 
15  Lamp cover
The lamp unit is inside.
16 Vertical lens shift dialAdjusts the vertical position of the projected image.
Attention
 
f Do not block the ventilation ports (intake and exhaust) of the projector .
 
r Control panel and Indicators
1 Power button < v/b>
Sets the projector to the state where the projector is 
switched off (standby mode). Also starts projection when 
the power is switched off (standby mode).
2  Power indicator  
Displays the status of the power.
3  Lamp indicator   
Displays the status of the lamp.
4  Temperature indicator   
Displays the status of the internal temperature.
5  Ambient Luminance sensor
Detects room's light and select proper image quality.
6   button
Displays or hides the main menu.  (
Æ page 53)7 
 button
Determines and executes an item in the menu screen.
8   button
Switches the input signal to project. (
Æ page 47)
9  asqw  buttons
Navigates the menu screen.
And use qw to adjust the volume level, use  as to 
page up or page down files such as PowerPoint
® through 
wireless manager. 
10   button
Automatically adjusts the image display position while 
projecting the image.(
Æ page 46)  
In addition, it acts as  button when using the 
MEMORY VIEWER function.
26 -  ENGLISH
Chapter 1   Preparation - About your projector  
						

							 
r Connecting terminals
1   terminal
This is the terminal to input RGB signals or YC
BCR/YPBPR 
signals. Or output the RGB signals or YCBCR/YPBPR 
signals to an external device.
2   terminal
This is the terminal to input RGB signals, Y/C signals or 
YC
BCR/YPBPR signals.
3   terminal
This is the terminal to input HDMI1 signals.
4   terminal
This is the terminal to input HDMI2 signals.
5   terminal
This terminal is used to connect the projector to the 
computer with a USB cable when you want to use the 
USB display function of the application software "Wireless 
Manager ME6.2".
For details, please refer to the "Operating Instructions-
Wireless Manager ME6.2" in CD-ROM.
6   terminal
This terminal is to insert the USB memory directly.
(
Æ page 119) 7 
 terminal
This is the LAN terminal to connect to the network.   
This is also used when connecting a device for 
transmitting video and audio signals via the LAN terminal.
8   terminal
This is the RS-232C compatible terminal to externally 
control the projector by connecting a computer.
9   terminal
This is the terminal to input video signals.
10   terminal
This is the terminal to input audio signals.
Left input  and right input  are provided for the 
 terminal.
11   terminal
This is the terminal to input audio signals.
12   terminal
This is the terminal to input audio signals. Or connect
 the 
MIC to this terminal.
13   terminal
This is the terminal to output the input audio signal to the 
projector.
 
Attention
 
f When a LAN cable is directly connected to the projector, the network connection must be made indoors.
ENGLISH  -  27
Chapter 1   Preparation - About your projector  
						

							Preparing the remote control
Inserting and removing batteries
(ii)(i)
1) Open the cover. (Fig. 1)
2)  Insert batteries and close the cover (insert the "m" side first). (Fig. 2)
 
f When removing the batteries, perform the steps in reverse order.
When using the system with multiple projectors
When you use the system with multiple projectors, you can operate all the projectors simultaneously or each projector 
individually by using single remote control, if a unique ID number is as\
signed to each projector.
When you want to set the ID number, at first you need to complete the Initial setting, and then after setting the ID number of 
the projector, set the ID number on the remote control. About Initial setting, please refer to “When the initial setting screen is 
displayed” ( x page 42).
The factory default ID number of the unit (the projector and the remote control) is set to [ALL], you can control with this setting. 
If necessary, please set the ID number to the remote control and the projector. About how to set the ID number of the remote 
control, please refer to “Setting the ID number of the remote control” ( x page 50).
Note
 
f Set the ID number of the projector from the [PROJECTOR SETUP] menu → [PROJECTOR ID] ( x page 79).
Fig. 1
Fig. 2
28 - ENGLISH
Chapter 1   Preparation - Preparing the remote control  
						

							Attaching the Lens Cap
When moving this projector or while not using it over an extended period of time, attach the lens cap.
To prevent loss for the lens cap, please according to the following proce\
dures, attach the lens cap with the string of 
accessories. 
1) Thread the thinner end of the string through the hole on the lens cap.
Lens cap
String
2)  Thread the other end of the string through the hole on the bottom of the\
 projector.
ENGLISH  -  29
Chapter 1   Preparation - Attaching the Lens Cap  
						

							Chapter 2   Getting Started
This chapter describes things you need to do before using the projector \
such as the setup and 
connections.
30 - ENGLISH