Panasonic Pt D5700el Projector User Manual

							41
ENGLISH
Basic control page
This page is the first page displayed when the projector is accessed through a Web browser.
To move from another page, click [Projector control], then [Basic control]. 
Power On/Off control 
Shutter control
Network set up button
Click this item, and a network set up page for IP address and
other items appear.
Change password button
Signal System Switching
Control button
Click this item, and a projector control
page appears.
E-mail set up button
Click this item, and an E-mail setting
page appears.
Monitor information button
Click this item, and the status of the
projector is displayed.
OSD
(On-screen Display) 
display/non-display
Use these to select the input
signals.
%&~	
@&O
 
 
 
 .
 
 
						

							42
Using Web Browser Control 
Detail control page
Click [Projector control], then [Detail control] to display the Detail control page.
Pressing these buttons controls the projector and updates the on-screen
description on the right of the control page when control is finished.
This button updates the on-screen
description on the right of the control
page with the latest information.
On-screen status is displayed, even if
the on-screen of projector is set to off.
Monitor information page
Click [Projector control], then [Status information] to display the Status information page.
This page displays the projector statuses established for the items shown below.
Displays self-diagnosis information.
Displays temperature of projector’s
intake air.
Displays temperature inside the
projector.
Displays temperature around the lamp.
Displays the lamp1 lit hours.
Displays the lamp2 lit hours.
Displays the type of projector.
Displays used hours of the projector.
Displays the firmware version of the projector main unit.
Displays the input switching status.
%&~	
@&O
 
 
 
 .
 
 
						

							43
ENGLISH
When [FAILED] has appeared for an item
Parameter
MAIN CPU BUS
FAN
OPTICS MODULE
TEMPERATURE
INPUT AIR TEMPERATURE
AROUND LAMP
TEMPERATURE
LAMP REMAIN TIME
LAMP STATUS
SHUTTER
AIR FILTER
OPTICS MODULE TEMP.SENSOR
INPUT AIR TEMP.SENSOR
AROUND LAMP 
TEMP. SENSOR
BATTERY
AIRFLOW SENSOR
COLOR WHEEL
˜
COVER OPEN
Description
Trouble has occurred in the microcomputer circuitry. Consult your dealer.
Trouble has occurred in the fan or its drive circuit. Consult your dealer.
The temperature inside the projector is high. 
It may be that the projector is being used where the ambient temperature is
high such as near a heating appliance.
The input air temperature is too high. 
It may be that the projector is being used where the ambient temperature is
high such as near a heating appliance.
The temperature near the lamp has risen very high.
Something may be blocking the exhaust vent.
The lamp runtime has exceeded the prescribed cumulative time, and it is
now time to replace the lamp.
The lamp has failed to light.
Wait a short while for the lamp to cool off, and then turn on the power.
Trouble has occurred in the shutter circuitry. Consult your dealer.
Too much dust accumulates on the air filter.  
Turn off the MAIN POWER switch using the procedure on page 23 and
clean the air filter (refer to page 54).
Trouble has occurred in the temperature detection sensor inside the
projector. Consult your dealer.
Trouble has occurred in the sensor used to detect the input air temperature.
Consult your dealer.
Trouble has occurred in the temperature detection sensor around lamps.
Consult your dealer.
The backup battery has been run out. Consult your dealer.
Trouble has occurred in the air volume sensor. Consult your dealer.
Trouble has occurred in the colour wheel or the colour wheel drive circuit.
Consult your dealer.
The lamp unit cover is not properly fitted. Check the fitting of the lamp unit
cover. (page 56)
Error information page
When  is displayed on the status information screen, click it to display the error details.
• Depending on the nature of the error, the projector may be placed in the standby mode for its own
protection.Note
OK: Normal operation
FAILED: Occurrence of trouble
%&~	
@&O
 
 
 
 .
 
 
						

							44
Using Web Browser Control 
Periodic warning interval setting (E-mail
is sent on the checked days of the
week/times)
Enter the E-mail address of your
desired recipient.
Select the conditions for sending E-mail.
ERROR:
an error is detected by self-
diagnosis.
LAMP RUNTIME:
remaining lamp service time has
reached the value set in the field.
INPUT AIR TEMPERATURE:
intake air temperature has reached the
value set in the field.
E-mail set up page
With this projector, if a problem occurs or if the lamp usage time reaches a set value, an E-mail message can be
sent to one or more preset E-mail addresses (maximum two addresses). Click [Projector control], then [E-mail
set up] to display the E-mail set up page.
The user can enter the location of, for
example, the installed projector so that
the recipient may easily identify the
originator of the E-mail.
(maximum 63 characters)
The user can modify the threshold temperature for sending
temperature warning mail. If the temperature rises above the set
value, control sends temperature warning mail.
The user can modify the minimum time
interval of temperature warning mail.  The
default value is 60 minutes.  In this case,
the user cannot send another mail for 60
minutes after sending previous
temperature warning mail even the set
warning temperature is reached again.
Enter the IP address or server name of the
E-mail server (SMTP). The DNS server
must be set if the server name is entered.
Enter the E-mail address of the projector.
(maximum 63 characters)
Select “Enable” to use the E-mail
function.
%&~	
@&O
 
 
 
 .
 
 
						

							45
ENGLISH
• Only alphanumeric characters, “.”, “_”, “-”, or “@” are available to set an E-mail address.Note
Select the conditions for sending the second E-mail.
ERROR:an error is detected by self-diagnosis.
LAMP RUNTIME:remaining lamp service time has reached the value set in the field.
INPUT AIR TEMPERATURE: intake air temperature has reached the value set in the field.
Enter the E-mail address to which the
E-mail is to be sent when two E-mail
addresses are going to be used. Do not
enter it when the second E-mail
address is not going to be used.
Check these boxes when E-mail is to
be sent periodically to two E-mail
addresses. E-mail will be sent at the
times and on the days checked.
Button to update settings
Authentication server set up page
The authentication server is set on this page when POP authentication or SMTP authentication is required for mail transmissions.
Click [Network set up], then [Authentication set up] to display the authentication server set up page.
For SMTP authentication, change the
authentication method to use, as desired.
Change the authentication method as desired.
Enter the POP server name.
Available input characters:
alphanumeric characters (A - Z, a - z, 
0 - 9), hyphen (-) period (.)
Enter the user name for the SMTP or
POP server.
Enter the password for the SMTP or
POP server.
Button to update settings
Enter the SMTP server port number.
Enter the POP server port number.
%&~	
@&O
 
 
 
 .
 
 
						

							46
Using Web Browser Control 
Ping test page
This page makes it possible to check whether the network is connected to the E-mail server, authentication server, DNS server, etc.
Click [Network set up], then [Ping test] to display the Ping test page.
Display which appears
when the connection was
successful.
Display which appears
when the connection failed.
DNS server set up page
Click [Network set up], then [DNS server set up] to display the DNS server set up page.
Primary DNS server address
Available input characters:
numbers (0 - 9), period (.)
(ex. 192.168.0.253)
Secondary DNS server address
Available input characters: 
numbers (0 - 9), period (.)
(ex. 192.168.0.254)
Button to update settings
Enter the IP address of the server to
be tested.
Button for conducting the test.
%&~	
@&O
 
 
 
 .
 
 
						

							47
ENGLISH
Contents of mail sent
• Mail with the contents shown below is sent when the E-mail
settings have been established.
Adjust clock page
Click [Network set up], then [Adjust clock] to display the Adjust clock page.
• Mail with the contents shown below is sent
when an error has occurred.
• If the time becomes incorrect immediately after setting the correct time, then the battery needs to
be changed. Contact the dealer where you bought the projector to have the battery changed.
Note
=== Panasonic projector report(CONFIGURE) ===
Projector Type          : D5700
-----  E-mail setup data -----
TEMPERATURE WARNING SETUP 
MINIMUM TIME           at [ 60] minutes interval 
INPUT AIR TEMPERATURE  Over [ 45C / 113F ] 
ERROR [ ON  ] 
LAMP1 RUNTIME [ ON  ] at REMAIN [ 100] H 
LAMP1 RUNTIME [ ON  ] at REMAIN [ 200] H 
LAMP2 RUNTIME [ ON  ] at REMAIN [ 300] H 
LAMP2 RUNTIME [ ON  ] at REMAIN [ 400] H 
INPUT AIR TEMPERATURE [ OFF ] 
PERIODIC REPORT 
Sunday [ ON  ] Monday [ OFF ] Tuesday [ ON  ] Wednesday [ OFF ] 
Thursday [ ON  ] Friday [ OFF ] Saturday [ ON  ] 
00:00 [ ON  ] 01:00 [ OFF ] 02:00 [ ON  ] 03:00 [ OFF ] 
04:00 [ OFF ] 05:00 [ ON  ] 06:00 [ OFF ] 07:00 [ ON  ] 
08:00 [ ON  ] 09:00 [ OFF ] 10:00 [ ON  ] 11:00 [ OFF ] 
12:00 [ OFF ] 13:00 [ ON  ] 14:00 [ OFF ] 15:00 [ ON  ] 
16:00 [ ON  ] 17:00 [ OFF ] 18:00 [ ON  ] 19:00 [ OFF ] 
20:00 [ OFF ] 21:00 [ ON  ] 22:00 [ OFF ] 23:00 [ ON  ] 
-----  check system -----
MAIN CPU BUS [   OK   ]
FAN [   OK   ]
OPTICS MODULE TEMPERATURE [   OK   ]
INPUT AIR TEMPERATURE [   OK   ]
AROUND LAMP TEMPERATURE [   OK   ]
LAMP2 REMAIN TIME [   OK   ]
LAMP1 REMAIN TIME [   OK   ]
•
•
•=== Panasonic projector report(ERROR) ===
Projector Type          : D5700
–––––check system –––––
MAIN CPU BUS  [ OK ]
FAN [ OK ]
OPTICS MODULE TEMPERATURE [ OK ]
INPUT AIR TEMPERATURE [ OK ]
AROUND LAMP TEMPERATURE [ OK ]
LAMP2 REMAIN TIME [ OK ]
LAMP1 REMAIN TIME [ OK ]
LAMP2 STATUS [ OK ]
LAMP1 STATUS [ OK ]
SHUTTER [ FAILED ]
AIR FILTER [ OK ]
OPTICS MODULE TEMP.SENSOR [ OK ]
INPUT AIR TEMP.SENSOR [ OK ]
AROUND LAMP TEMP.SENSOR [ OK ]
BATTERY [ OK ]
AIRFLOW SENSOR [ OK ]
COLOR WHEEL [ OK ]
COVER OPEN [ OK ]
(Error code 00 10 00 00 00 00 00 00)
Input air temperature : 30 degC /  86 degF
Optics module temperature : 30 degC /  86 degF
Around lamp temperature : 37 degC /  98 degF
SET RUNTIME 30 H
POWER ON 33 times
LAMP1 ON 34 times
LAMP1 LOW 25 H
LAMP1 HIGH 5 H
LAMP2 ON 24 times
LAMP2 LOW 16 H
LAMP2 HIGH 4 H
LAMP1 REMAIN 1476 H
LAMP2 REMAIN 1484 H
----- Network configuration -----
IP address 192.168.0.8
MAC address 00:00:00:00:00:00
Thu Mar 02 14:11:02 2006
----- Memo -----
Time zone selection
Button to update time zone setting
Button to update time and date
settings 
New date field
New time field
%&~	
@&O
 
 
 
 .
 
 
						

							48
Using Web Browser Control 
Network config page
Click [Network set up], then [Network config] to display the Network config page.
Network status page
Click [Network set up], then [Network status] to display the Network status page.
Set this to ON to enable the DHCP client
function.
Enter the IP address if DHCP server is
not used.
Enter the gateway address if DHCP
server is not used.
Enter the name of the projector here. Enter the host name
here if it is required when the DHCP server is going to be
used, for instance.
Enter the subnet mask if DHCP server is
not used.
MAC address display 
Network status display
Set IP address display
Set subnet mask display 
Network software version display 
%&~	
@&O
 
 
 
 .
 
 
						

							49
ENGLISH
Using the PJLink™protocol
The network functions of the projector are compatible with PJLink™Class 1. The operations mentioned below can
be performed from a personal computer using the PJLink™protocol.
• Projector settings
• Projector status inquiry
Supported commands
The commands for controlling the projector using the PJLink™protocol are as given in the table below.
PJLink™security authentication
The password used for PJLink™is the same as the password set for WebBrowser control. 
When using these commands without authentication, leave the WebBrowser control password unspecified. 
• PJLink™is a pending trademark in Japan, the United States and other countries and regions. For details on
PJLink™specifications, refer to the Japan Business Machine and Information System Industries Association
website. The URL is http://pjlink.jbmia.or.jp/english/
Power control
Power status inquiry
Input selection
Input selection inquiry
Shutter control
Shutter status inquiry
Error status inquiry
Lamp status inquiry
Input selection list inquiry
Projector name inquiry
Manufacturers name inquiry
Model name inquiry
Other information inquiry
Class information inquiryParameter
0 = Standby
1 = Power “ON”
Parameter
0 = Standby
1 = Power “ON”
2 = Cooling down
3 = During warm-up
Parameter
11 = RGB1 
12 = RGB2 
21 = VIDEO
22 = S-VIDEO 
31 = DVI-D
Parameter
30 = Shutter mode OFF (Mute reset of video)
31 = Shutter mode ON (Mute video)
Parameter
1st byte: Refers to fan error; one of 0 to 2
2nd byte: Refers to lamp error; one of 0 to 2
3rd byte: Refers to temperature error; one of 0 to 2
4th byte: Refers to cover open error; one of 0 to 2
5th byte: Refers to filter warning; one of 0 to 2
6th byte: Refers to some other error; one of 0 to 2
The meaning of 0 to 2 is as given below.
0 = Error not detected    1 = Warning    2 = Error
Parameter
First number (digits 1 to 5): Lamp1 cumulative time
Second number: 0 = Lamp1 OFF; 1 = Lamp1 ON
Third number (digits 0 to 5): Lamp2 cumulative time
Fourth number: 0 = Lamp2 OFF; 1 = Lamp2 ON
Parameter responds with following values:
“11 12 21 22 31”
Responds with the name set in “HOST NAME” of “NETWORK”
Responds with “Panasonic”
Responds with “D5700” or “DW5100”
Responds with version number and so on
Responds with “1”Remarks
Command Control Description
POWR
POWR ?
INPT
INPT ?
AVMT
AVMT ?
ERST ?
LAMP ?
INST ?
NAME ?
INF1 ?
INF2 ?
INFO ?
CLSS ?
%&~	
@&O
 
 
 
 .
 
 
						

							50
Setting the security
The projector’s security function enables the password
input screen to be displayed or a company’s URL
address to be set and displayed underneath the
projected images.
PASSWORD
SET INPUT
(When using the projector for the first time)
Press the , , , , , ,  and 
buttons in this order, and press the ENTER button.
(When the password has been changed)
Input the new password, and press the ENTER button.
PASSWORD 
It is possible to display the password input screen
each time the power is turned on. If this option is
used, no operations except for the POWER button
can be performed without inputting the correct
password.
ON : Password input is enabled.
OFF : Password input is disabled.
PASSWORD CHANGE
The password can be changed. Press the ENTER
button.
Set the password using the ,  ,  , 
buttons (up to 8 buttons can be set).
Press the ENTER button.
Confirm the password by inputting it again. 
Press the ENTER button.
(This completes the settings.) 
• Asterisks ( ) will appear on the
screen in the place of the actual
password when the password is input.
• If the password is input incorrectly, the
display returns to “NEW”. Input the
correct password.Note
DISPLAY SETTING
The image can be displayed based on the settings
below.
OFF : The normal image is displayed.
TEXT : Preset text is constantly displayed
under the projected image.
LOGO1 : The picture registered by the user will
be projected.
LOGO2 : The Panasonic logo is projected.
TEXT CHANGE
The text which is to be displayed when “TEXT” has
been selected for the “DISPLAY SETTING” can be
changed. Press the ENTER button.
Select the text using the, , , 
buttons, and press the ENTER button. (Up to
22 alphanumerics can be input in succession.)
Select “OK” using the  ,  ,  , 
buttons, and press the ENTER button.
• To cancel the change at any time, select
“CANCEL”.
CONTROL DEVICE SETUP
It is possible to restrict operation from the remote
control and the main unit controls.
CONTROL PANEL : 
Operation from the main unit controls can be
restricted.
ENABLE : Main unit control operation is
enabled
DISABLE : Main unit control operation is
disabled
REMOTE CONTROLLER :
Operation from the remote control can be
restricted.
ENABLE : Remote control operation is
enabled
DISABLE : Remote control operation is
disabled
• Setting changes will be reflected only
when you select “OK” at the
confirmation screen displayed after
you press the ENTER button at the
“ENABLE/DISABLE” menu. When the
setting has been reflected, the on-
screen menu disappears.
To continue and perform other
operations, press the MENU button
and display the MAIN MENU.
• When you attempt to operate controls
(remote control or main unit) that are
set to “DISABLE”, the password input
screen is displayed. To change the
setting, input the security password
and change the operation setting. The
password input screen disappears
when you press the MENU button or if
you do not perform any operation for
10 seconds.Note
%&~	
@&O
 
 
 
 .