Panasonic Pt Dw5000el Projector User Manual

							11
ENGLISH
AC IN terminal (page 22) 
Connect the supplied line power cord into this
receptacle.
Do not connect any other cable to this socket.
Air filter (page 41)
Burglar lock
Attach a commercial burglar prevention cable (e.g.,
from Kensington) to this lock port. It is compatible
with the Microsaver Security System from
Kensington. Contact details for this company are
given below.
Kensington Technology Group ACCO Brands Inc.
2885 Campus Drive San Mateo, CA94403
Tel (650)572-2700
Fax (650)572-9675
http://www.kensington.com/
http://www.gravis.com/
Clasp for attaching anti-theft chain 
Attach a chain or other fastening device available
from a hardware store through this clamp.
Level-adjusting feet (page 22)
Use these feet to adjust the tilt of the projector.
(The leveling feet at the front left and right can be
adjusted.)
Lens lock button (page 24)
Press this to remove the projection lens.
Projection lens
Lens for projecting images on the screen.
Lens left/right adjusting dial (page 24)
Turn this clockwise to move the screen to the left;
conversely, turn it counterclockwise to move it to
the right.
Remote control receiver window (front) (page 14)
This window receives the signal beam emitted from
the remote control.
Focus ring (page 24)
For focus adjustment.
Powered focus adjustment is also available.
Temperature monitor (TEMP) (page 40)
Lighting or blinking of this lamp indicates an
abnormal condition of the internal temperature.
LAMP1 monitor (page 40)
This lamp lights up when the time to replace lamp
unit 1 is reached. It also blinks if something
unusual occurs in the lamp circuit.
LAMP2 monitor (page 40)
This lamp lights up when the time to replace lamp
unit 2 is reached. It also blinks if something
unusual occurs in the lamp circuit.
Power indicator (page 22)
The lamp lights in red when the MAIN POWER
switch is turned to “ | ” (on). It turns to green when
the POWER ON button of the remote control or the
main unit is pressed.
Lens cap
Cap the lens whenever the projector is left unused.
Ventilation holes
Side-mounted 
connection terminals 
(page 13)Status LED lights
(Refer to the figure 
 on the right.)
Front and side of the projector
Status LED lights
• Do not remove the upper cover (white top
panel).Attention 
						

							12
Name and function of parts 
Ventilation holes
Lamp unit cover
The lamp unit is housed.
MAIN POWER switch (page 22)
Use this switch to turn on “I” and off “O” the main
power applied to the projector.
Remote control receiver window (rear) (page 14)
This also receives the signal beam coming from
the remote control.
POWER ON ( I ) button (page 22)
Turns on the power.
POWER OFF ( ) button (page 23)
Turns off the power.
RGB1 button (page 22)
Switches to RGB1 input.
RGB2 button (page 22)
Switches to RGB2 input.
VIDEO button (page 22)
Switches to video input.
S-VIDEO button (page 22)
Switches to S-VIDEO input.
MENU button (page 27)
Displays and clears the Main Menu. It can also
return to the previous screen when the menu is
displayed.
The on-screen display (OSD) selection menu can
be displayed by holding down the menu key for at
least three seconds.
AUTO SETUP button (page 25)
Pressing this button while projecting an image
automatically corrects the picture positioning on
the screen.
DVI button (page 22)
Switches to DVI-D input.
SHUTTER button (page 25)
Press this button to black out the image
temporarily.
ENTER button (page 27)
Press this button to enter your menu selection or to
run function.
LENS button (page 24)
Switches to the adjustment mode for lens focus,
zoom and shift (position).
Arrow ( ) buttons (page 27)
Use to select an item on the menu screen, change
setting and adjust the level.
Also use them to enter the “SECURITY” password.
Rear view of the main unitControls on rear panel
Controls on rear panel 
						

							13
ENGLISH
VIDEO IN terminal (page 21) 
An input terminal for video signals. (BNC)
S-VIDEO IN terminal (page 21)
An input terminal for S-video signals. 
(MIN4-pin DIN)
This terminal complies with S1 signals and
automatically toggles between 16:9 and 4:3
according to the size of input signals.
RGB 1 input (RGB 1 IN) terminal (page 21)
A terminal to input RGB or YP
BPRsignals. (BNC)
RGB 2 input (RGB 2 IN) terminal (page 21)
A terminal to input RGB or YP
BPRsignals. (D-SUB
15-pin female)
DVI-D IN terminal (page 21)
DVI-D signals are applied to this terminal. (24-pin
DVI connector)
LAN terminal (page 37)
This terminal is used to control the projector from
the PC. (10Base-T/100Base-TX compliant)
REMOTE1 lN/OUT terminal (page 16)
When two or more main units are used in the
system, they can be connected and controlled with
M3 stereo mini jack cable available in the market.
REMOTE2 IN terminal
The user can remotely control the main unit by
using an external control circuit to this terminal. 
(D-SUB 9-pin female)
SERIAL IN terminal (pages 21, 38)
Use the RS232C serial terminal as an alternative
interface for controlling the projector from your PC.
(D-SUB 9-pin female)
SERIAL OUT terminal (pages 21, 38)
The signal applied to the serial input terminal
appears at this terminal. (D-SUB 9-pin male)
RGB 2 IN
 VDSYNC/HDB/PBG/YRR/P
SERIALREMOTE 1
REMOTE 2INOUTLANDVI-D INRGB 1 INVIDEO INS-VIDEO  IN
IN OUT
Side-mounted
connection terminals
LAN terminal (10Base-T/100Base-TX)
Connect LAN cable. 
LAN 10/100 lamp (Yellow)
Lights up when 100Base-TX
connected.
LAN LINK/ACT lamp (Green)
Lights up when connected.
Flashes when receiving/sending
signals. 
						

							14
Using the remote control unit
Loading dry cells
When loading batteries into the battery
compartment of the remote control, make sure that
their polarities are correct.
1. Open battery compartment lid.
Open the lid in the order of steps  and  .
2. Insert the dry cells.
Into battery compartment, with their polarities
orientated as indicated ( ,  ) in the
compartment.
3. Close the battery compartment lid.
Replace the battery compartment lid over the
compartment and slide until it clicks.
Effective range of remote
control operation
The remote control should normally be aimed at either
the front or rear remote control receiver window on
the projector (figure 1). Otherwise, it may also be
aimed at the screen, which will reflect commands
back to the projector’s front receiver window as
illustrated in figure 2.
The effective control range is approx. 7 metres from
the beam receiver on the front or rear.
• Do not drop the remote control unit.
• Do not expose remote control unit to
any liquid.
• Do not use NiCd batteries.AttentionNote• When the remote control is aimed at
the screen, the effective control range
may be reduced due to the optical loss
by screen reflection.
• The remote control may not function
properly if an object is in the light path.
• The remote control receiver may not
function properly in intense ambient
light such as fluorescent lamps.
Carefully site the projector so its
remote control receiver windows will
not be directly exposed to intense
light.
Accessory type-AAA dry
batteries (insert the negative
side first).
(Front)(Rear)
[Top view]
[Side view] Remote 
control Remote 
controlRemote 
control
Remote 
control 15˚
15˚15˚
15˚ 30˚ 30˚
30˚ 30˚
Remote control 
receiver window 
(rear) Remote control 
receiver window 
(front)Projector
Remote control Screen
Figure 1
Figure 2 
						

							15
ENGLISH
Using the remote control as a PC mouse
Operation mode selector switch
Put the knob to the Computer position.
•ENTER button
Pressing the front, rear, left and right edges of the
button moves the mouse cursor up, down, left and
right.
•Right click ( ) button
This button can be used as the right mouse button.
•Left click ( ) button
This button can be used as the left mouse button.
•PAGE UP button
This button can be used as the Page Up button on
the PC keyboard.
•PAGE DOWN button
This button can be used as the Page Down button on
the PC keyboard.
•Click button
This button can be used as the left mouse button.
PAGE DOWN button
Operation mode
selector switch ENTER button
Right click (  ) button PAGE UP button
Left click
(  ) button
Click button
• To use the remote control as a mouse, please purchase an optional wireless mouse receiver
(model No.: ET-RMRC2).Note
Setting projector ID number to remote control
Every projector has its ID number and the ID number of the controlling projector must be set to the remote
control in advance so that the user can operate the remote control. The ID number of the projector is set to
“ALL” on shipping, and use the ID ALL button of the remote control when using only a single projector.
Procedure of ID setting 
Change the position of the operation mode selector switch to “Computer”.
Press the ID SET button, and within five seconds use the number (0 to 9) buttons to
enter the 2-digit ID number set by the projector.
Change the position of the operation mode selector switch to “Projector”.
However, if the ID ALL button is pressed, the projector can be controlled regardless of the ID number of the
projector (simultaneous control mode).
• Do not press the ID SET button accidentally or carelessly because the ID number on the remote
control can be set even when no projector is around.
If the ID SET button is pressed, the ID number goes back to the one set before pressing the ID
SET button unless a numeric button is pressed within five seconds after the ID SET button is
pressed.
• Your specified ID number is stored in the remote control unit unless another one is specified later.
However, the stored ID will be erased if the batteries of the remote control are left exhausted.
When the dry cells are replaced, set the same ID number again.
• When specifying the ID number, enter a 2-digit number even if the ID has only one digit.
(Example: set “02” if the ID number is “2.”)Attention 
						

							16
Using a wired remote control
When multiple main units are connected in the
system, connect the units with the M3 stereo mini
jack cable available in the market to simultaneously
control the multiple main units with a single remote
control unit through the REMOTE1 IN/OUT
terminal. It is effective to use the wired remote
control in the environment in which an obstacle
stands in the light path or where devices are
susceptible to outside light.
SB/PBG/YRR/P
REMOTE 1
REMOTE 2RGB 1 INVIDEO INS-VIDEO  IN
IN OUT
Connect to the 
secondary projector
M3 stereo mini 
jack cable 
(available in the 
market)
Using the remote control unit
• Use two-core shielded cable of
length smaller than 15 m. If the
cable length exceeds 15 m, or if the
shielding of the cable is inadequate,
the operation may be unsatisfactory.Attention
Installation
Projection schemes
Any of the following four projection schemes can be used
depending on user’s needs or viewing conditions.
Use “OPTION2” menu (chosen from the MAIN
MENU) to choose the appropriate projection
scheme (see page 34).
Projection Scheme 1
Front projection Rear projection
Table standingProjection Scheme 2
Ceiling mount
(Default position)
Installation geometry
After the projector is roughly positioned, picture size
and vertical picture positioning can be finely
adjusted with the powered zoom lens and lens tilt
mechanism.
Side view
With optional ceiling mount
bracket (ET-PKD55)
261
HH
ScreenSH180
L
L
 421-541
Top view
314 157
175 87.5 LScreen
SW
L : Projection distance
SH : Image height
SW : Image width
H : Distance from centre of lens to bottom edge
of projected image.
• Do not place or use one projector on
top of another projection unit.
• Leave a clearance of at least 50 cm so
that the ventilation opening on the rear
panel will not be blocked.Attention 
						

							17
ENGLISH
Projection distance by projection lens
Listed in the table below are the lens projection distances for the PT-D5600E (lens included), PT-D5600EL (lens
sold separately), PT-DW5000E (lens included) and PT-DW5000EL (lens sold separately).
• PT-D5600E, PT-D5600EL
50
60
70
80
90
100
120
150
200
250
300
350
400
500
600
Diagonal
length
(SD)
0.76
0.91
1.07
1.22
1.37
1.52
1.83
2.29
3.05
3.81
4.57
5.33
6.10
7.62
9.14 Height
(SH)
1.02
1.22
1.42
1.63
1.83
2.03
2.44
3.05
4.06
5.08
6.10
7.11
8.13
10.16
12.19 Width
(SW)
1.33
1.61
1.89
2.16
2.44
2.71
3.27
4.09
5.47
6.85
8.23
9.61
10.99
13.75
16.51
Minimum
(LW)
1.81
2.18
2.56
2.93
3.30
3.67
4.42
5.53
7.39
9.25
11.11
12.97
14.83
18.55
22.27
Maximum
(LT)
1.79
2.16
2.53
2.90
3.27
3.64
4.38
5.49
7.34
9.19
11.04
12.89
14.74
18.44
22.14
Minimum
(LW)
2.38
2.86
3.35
3.84
4.33
4.82
5.79
7.26
9.70
12.14
14.58
17.02
19.46
24.34
29.22
Maximum
(LT)
3.84
4.63
5.43
6.22
7.02
7.81
9.40
11.79
15.76
19.74
23.71
27.69
31.66
39.61
47.56
Minimum
(LW)
6.03
7.26
8.49
9.73
10.96
12.19
14.65
18.35
24.51
30.67
36.83
42.99
49.15
61.47
73.79
Maximum
(LT)
0.79
0.96
1.13
1.29
1.46
1.62
1.96
2.45
3.28
—
—
—
—
—
—
Model No. :
ET-DLE050Projected screen size
(4:3 aspect ratio)Wide-angle
zoom lens
Model No. :
ET-DLE100  Standard 
zoom lens
2.45
2.96
3.46
3.97
4.47
4.97
5.98
7.49
10.01
12.53
15.05
17.57
20.09
25.13
30.17
Minimum
(LW)
4.04
4.87
5.69
6.52
7.34
8.16
9.81
12.28
16.40
20.52
24.64
28.76
32.88
41.12
49.36
Maximum
(LT)
Intermediatefocus
zoom lens
Model No. :
ET-DLE200Optional lens
Long-focus
zoom lens
Model No. :
ET-DLE300
Wide-angle
fixed-focus
lens
(0.8)
(L)(1.33 - 1.78) (1.8–2.5) (2.5 - 4.0) (3.7 - 5.7)
5.90
7.08
8.26
9.43
10.61
11.78
14.14
17.66
23.54
29.42
35.30
41.18
47.06
58.82
70.58Minimum
(LW)
8.30
9.94
11.59
13.23
14.88
16.53
19.82
24.76
32.99
41.22
49.45
57.68
65.91
82.37
98.830 - 0.38
0 - 0.46
0 - 0.53
0 - 0.61
0 - 0.69
0 - 0.76
0 - 0.91
0 - 1.14
0 - 1.52
0 - 1.91
0 - 2.29
0 - 2.67
0 - 3.05
0 - 3.81
0 - 4.57
Maximum
(LT)
Ultra-long-focus
zoom lens
Model No. :
ET-DLE400Height
position
: H (5.7 - 8.0) Unit : m, (SD : inch)
Screen aspect ratio 4:3
Unit : m, (SD : inch)
50
60
70
80
90
100
120
150
200
250
300
350
400
500
6000.62
0.75
0.87
1.00
1.12
1.25
1.49
1.87
2.49
3.11
3.74
4.36
4.98
6.23
7.471.11
1.33
1.55
1.77
1.99
2.21
2.66
3.32
4.43
5.53
6.64
7.75
8.86
11.07
13.281.46
1.76
2.06
2.36
2.66
2.96
3.57
4.47
5.97
7.48
8.98
10.49
11.99
15.00
18.011.98
2.38
2.79
3.19
3.60
4.00
4.81
6.03
8.05
10.08
12.10
14.13
16.15
20.20
24.25 1.95
2.35
2.76
3.16
3.56
3.97
4.77
5.98
8.00
10.01
12.03
14.04
16.06
20.09
24.122.60
3.13
3.66
4.19
4.72
5.26
6.32
7.92
10.58
13.24
15.90
18.56
21.22
26.54
31.864.19
5.06
5.92
6.79
7.66
8.52
10.25
12.85
17.18
21.51
25.84
30.17
34.50
43.16
51.826.58
7.92
9.26
10.61
11.95
13.29
15.97
20.00
26.71
33.42
40.13
46.84
53.55
66.97
80.39 0.87
1.05
1.23
1.41
1.59
1.77
2.14
2.68
3.58
—
—
—
—
—
—2.68
3.23
3.78
4.33
4.88
5.42
6.52
8.17
10.91
13.66
16.40
19.15
21.89
27.38
32.874.41
5.31
6.21
7.11
8.01
8.90
10.70
13.39
17.88
22.37
26.86
31.35
35.84
44.82
53.806.43
7.71
8.99
10.27
11.55
12.83
15.40
19.24
25.64
32.05
38.45
44.86
51.26
64.07
76.889.03
10.82
12.62
14.41
16.20
18.00
21.58
26.96
35.93
44.89
53.86
62.82
71.79
89.72
107.650 - 0.38
0 - 0.46
0 - 0.53
0 - 0.61
0 - 0.69
0 - 0.76
0 - 0.91
0 - 1.14
0 - 1.52
0 - 1.91
0 - 2.29
0 - 2.67
0 - 3.05
0 - 3.81
0 - 4.57
Diagonal
length
(SD)Height
(SH)Width
(SW)Minimum
(LW)
Maximum
(LT)
Minimum
(LW)
Maximum
(LT)
Minimum
(LW)
Maximum
(LT)
Model No. :
ET-DLE050Projected screen size
(16:9 aspect ratio)Wide-angle
zoom lens
Model No. :
ET-DLE100  Standard 
zoom lens
Minimum
(LW)
Maximum
(LT)
Intermediatefocus
zoom lens
Model No. :
ET-DLE200Optional lens
Long-focus
zoom lens
Model No. :
ET-DLE300
Wide-angle
fixed-focus
lens
(0.8)
(L)(1.33 - 1.78) (1.8–2.5) (2.5 - 4.0) (3.7 - 5.7)Minimum
(LW)
Maximum
(LT)
Ultra-long-focus
zoom lens
Model No. :
ET-DLE400Height
position
: H (5.7 - 8.0)
Screen aspect ratio 16:9
The height position (H) of the ET-DLE050 is SH/2. 
						

							18
Installation
0.62 
0.75 
0.87 
1.00 
1.12 
1.25 
1.49 
1.87 
2.49 
3.11 
3.74 
4.36 
4.98 
6.23 
7.47 1.11
1.33
1.55
1.77
1.99
2.21
2.66
3.32
4.43
5.53
6.64
7.75
8.86
11.07
13.281.48
1.78
2.09
2.39
2.70
3.00
3.61
4.53
6.05
7.58
9.10
10.63
12.15
15.20
18.252.01
2.42
2.83
3.24
3.65
4.06
4.88
6.12
8.17
10.23
12.28
14.34
16.39
20.50
24.61 1.98
2.39
2.80
3.21
3.62
4.03
4.84
6.07
8.12
10.16
12.21
14.25
16.30
20.39
24.482.63
3.17
3.71
4.25
4.79
5.33
6.40
8.02
10.72
13.41
16.11
18.80
21.50
26.89
32.283.89
4.69
5.49
6.29
7.08
7.88
9.48
11.88
15.87
19.87
23.86
27.86
31.85
39.84
47.835.11
6.15
7.20
8.24
9.28
10.32
12.41
15.54
20.75
25.97
31.18
36.40
41.61
52.04
62.47 0.88
1.06
1.24
1.43
1.61
1.79
2.16
2.71
3.62
—
—
—
—
—
—2.71
3.27
3.83
4.38
4.94
5.49
6.61
8.27
11.05
13.83
16.61
19.39
22.17
27.73
33.294.47
5.38
6.29
7.20
8.11
9.02
10.84
13.57
18.12
22.67
27.22
31.77
36.32
45.42
54.525.17
6.23
7.29
8.35
9.41
10.47
12.59
15.78
21.08
26.39
31.69
37.00
42.30
52.91
63.529.78
11.76
13.75
15.73
17.71
19.69
23.66
29.61
39.52
49.44
59.35
69.27
79.18
99.01
118.84 Unit : m, (SD : inch)
50
60
70
80
90
100
120
150
200
250
300
350
400
500
6000 - 0.38
0 - 0.46
0 - 0.53
0 - 0.61
0 - 0.69
0 - 0.76
0 - 0.91
0 - 1.14
0 - 1.52
0 - 1.91
0 - 2.29
0 - 2.67
0 - 3.05
0 - 3.81
0 - 4.57
Diagonal
length
(SD)Height
(SH)Width
(SW)Minimum
(LW)
Maximum
(LT)
Minimum
(LW)
Maximum
(LT)
Minimum
(LW)
Maximum
(LT)
Model No. :
ET-DLE050Projected screen size
(16:9 aspect ratio)Wide-angle
zoom lens
Model No. :
ET-DLE100  Standard 
zoom lens
Minimum
(LW)
Maximum
(LT)
Intermediatefocus
zoom lens
Model No. :
ET-DLE200Optional lens
Long-focus
zoom lens
Model No. :
ET-DLE310
Wide-angle
fixed-focus
lens
(0.8)
(L)(1.33 - 1.78) (1.8–2.5) (2.5 - 4.0) (3.4 - 4.5)Minimum
(LW)
Maximum
(LT)
Ultra-long-focus
zoom lens
Model No. :
ET-DLE410Height
position
: H (4.5 - 8.4)
Screen aspect ratio 16:9
The height position (H) of the ET-DLE050 is SH/2.
• PT-DW5000E, PT-DW5000EL
Note• Black bands will appear at the top and bottom of the screen. 
						

							19
ENGLISH
Calculation formulas for projection distance by lens types
• PT-D5600E, PT-D5600EL
Standard 
zoom lens
Wide-angle fixed-
focus lens
Wide-angle
zoom lens
Intermediate-focus
zoom lens
Long-focus
zoom lens
Ultra-long-focus 
zoom lensModel No. :
ET-DLE050
Model No. :
ET-DLE100
Model No. :
ET-DLE200
Model No. :
ET-DLE300
Model No. :
ET-DLE400Minimum (LW)
Maximum (LT)
Minimum (LW)
Maximum (LT)
Minimum (LW)
Maximum (LT)
Minimum (LW)
Maximum (LT)
Minimum (LW)
Maximum (LT)L=0.0370 x SD-0.0650
L=0.0488 x SD-0.0638
L=0.0166 x SD-0.0361
L=0.0276 x SD-0.0452
L=0.0372 x SD-0.0478
L=0.0504 x SD-0.0657
L=0.0824 x SD-0.0758
L=0.0795 x SD-0.1380
L=0.1232 x SD-0.1310
L=0.1176 x SD+0.0244
L=0.1646 x SD+0.0651(L, LW, LT : m    SD : inch) Screen aspect ratio 4:3
Standard 
zoom lens
Wide-angle fixed-
focus lens
Wide-angle
zoom lens
Intermediate-focus
zoom lens
Long-focus
zoom lens
Ultra-long-focus 
zoom lensModel No. :
ET-DLE050
Model No. :
ET-DLE100
Model No. :
ET-DLE200
Model No. :
ET-DLE300
Model No. :
ET-DLE400Minimum (LW)
Maximum (LT)
Minimum (LW)
Maximum (LT)
Minimum (LW)
Maximum (LT)
Minimum (LW)
Maximum (LT)
Minimum (LW)
Maximum (LT)L=0.0403 x SD-0.0650
L=0.0532 x SD-0.0638
L=0.0181 x SD-0.0361
L=0.0301 x SD-0.0452
L=0.0405 x SD-0.0478
L=0.0549 x SD-0.0657
L=0.0898 x SD-0.0758
L=0.0866 x SD-0.1380
L=0.1342 x SD-0.1310
L=0.1281 x SD+0.0244
L=0.1793 x SD+0.0651(L, LW, LT : m    SD : inch) Screen aspect ratio 16:9
• PT-DW5000E, PT-DW5000EL
Screen aspect 16:9
Standard 
zoom lens
Wide-angle fixed-
focus lens
Wide-angle
zoom lens
Intermediate-focus
zoom lens
Long-focus
zoom lens
Ultra-long-focus 
zoom lensModel No. :
ET-DLE050
Model No. :
ET-DLE100
Model No. :
ET-DLE200
Model No. :
ET-DLE310
Model No. :
ET-DLE410Minimum (LW)
Maximum (LT)
Minimum (LW)
Maximum (LT)
Minimum (LW)
Maximum (LT)
Minimum (LW)
Maximum (LT)
Minimum (LW)
Maximum (LT)L=0.0409 x SD-0.0650
L=0.0539 x SD-0.0638
L=0.0183 x SD-0.0361
L=0.0305 x SD-0.0452
L=0.0411 x SD-0.0478
L=0.0556 x SD-0.0657
L=0.0910 x SD-0.0758
L=0.0799 x SD-0.1062
L=0.1043 x SD-0.1056
L=0.1061 x SD-0.1374
L=0.1983 x SD-0.1352(L, LW, LT : m    SD : inch)
Note• The dimensions in the table in pages 17-18 and the values obtained from the above formulas may
contain slight errors.
• When an SXGA signal is input and projected, the right and left ends of the picture will be blanked
and the aspect ratio will be 5:4.
• The brightness is different between the wide lens position settings and telephoto lens position
settings. 
						

							20
Connection
Setup precautions
• Before connecting any of your video/audio equipment to the projector, carefully read the owners manual
supplied with the equipment once again.
• All cable connections should be made with the entire system devices, including the projector, first turned off.
• Obtain commercial interconnecting cables for devices supplied with no accessory or optional interconnect
cables.
• Video signals containing too much jitter may cause the images on the screen to randomly wobble or shake.
Inserting a time base corrector (TBC) in the projector’s video line will relieve this problem.
• The projector only accepts composite-video, S-video, analogue-RGB (with TTL sync. level), and digital signal.
• Some PC models are not compatible with PT-D5600E/PT-D5600EL/PT-DW5000E/PT-DW5000EL projectors.
• The pin assignments on the S-VIDEO IN terminal are
as follows:• The pin assignments on the DVI-D input terminal
are as follows (interface with DVI-D output
terminal on PC):
• The pin assignments on the RGB2 input terminal are
as follows:
Viewed from mating side
Pin No.           Signal
Ground (luminance)
Ground (colour)
Luminance signal
Colour signal
Pin  : Not used.
Pins - , and : Ground.
 Viewed from mating side
            Signal
R/P
R
G/G · SYNC/Y
B/P
B
HD/SYNC
VD
Pin No.
Viewed from mating side
Pin No.            Signal
T. M. D. S data 2-
T. M. D. S data 2+
T. M. D. S data 2
shield
DDC clock
DDC data
T. M. D. S data 1-
T. M. D. S data 1+
T. M. D. S data 1
shield            Signal
+5 V
Ground
Hot plug sense
T. M. D. S data 0-
T. M. D. S data 0+
T. M. D. S data 0
shield
T. M. D. S clock 
shield
T. M. D. S clock+
T. M. D. S clock-Pin No.
• The DVI-D input terminal supports single link only.
• EDID settings should be performed to suit the DVI
equipment being connected. (Page 33)
• The DVI-D input terminal can be used to connect to a
DVI equipment, but note that images may not appear
or the projector may not work properly when
connected to certain DVI equipment. 
• This projector supports HDCP.