Panasonic Pv Dc352 Operating Instructions Manual

							11
1
3 2
1
ZOOM
INDEX INDEX
SELECT
STORESTOP
KL∫
OSD
COUNTER
V/REW
STILL ADV
OFF/ON
P.B.DIGITAL
DATE/
TIME
RESET
TITLE T
W
sVOLr¥RECMULTI/
P-IN-PPHOTO
SHOTSTART/
STOP
A.DUB
PLAY
PAUSE
FF/W
STILL ADV
MENU
ITEMSET
61 5
;ED
VAR.
SEARCHP.B.
ZOOM21
1
15˚
15˚
15˚ 15˚
ªInserting the Button-type Battery
Before using the remote controller, insert the supplied button-type battery.
1While pressing the Stopper 1, pull out the Battery Holder.
2Insert the button-type battery with the imprint (i) facing 
upward.
3Insert the Battery Holder into the Remote Controller.
≥When the button-type battery becomes weak, replace it with a new CR2025 
battery. (A battery is normally expected to last about one year. However, it 
depends on operation frequency.)
≥Be sure to match the poles properly when inserting the battery.
................................................................................................................................
................................................................................................................................ ................................................................................................................................ ......................................................................................................................................................................
............................................................................ ......................................
Warning
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by the 
equipment manufacturer. Discard used batteries according to 
manufacturer’s instructions.
Risk of fire, explosion and burns. Do not recharge, disassemble, heat 
above 212°F (100°C) or incinerate. Keep the Button-Type battery out of 
the reach of children. Never put Button-Type battery in mouth. If 
swallowed, call your doctor.
................................................................................................................................
................................................................................................................................ ................................................................................................................................ ......................................................................................................................................................................
............................................................................ ......................................
Replace battery with Panasonic PART NO. VSBW0004 (CR2025) only. 
Use of another battery may present a risk of fire or explosion.
Caution: Battery may explode if mistreated.
Dispose of used battery promptly. Keep away from children. 
Do not recharge, disassemble or dispose of in fire.
ªUsing the Remote Controller
1
Direct the Remote Controller at the Remote Control Sensor 
on the Palmcorder and press the desired button.
≥Distance from the Palmcorder: Within approximately 15 feet (5 meters)
≥Angle: Approximately 15 degrees in the vertical and horizontal 
directions from the central axis
≥The above operating ranges are for indoor use. Outdoors, or under strong 
light, the equipment may not operate properly even within the above 
ranges.
≥Within 3 feet (1 meter) range, you can also use the Remote Controller on 
the side (the LCD Monitor side) of the Palmcorder.
Selecting Remote Controller Modes
When two Palmcorders are used simultaneously, they can be operated 
individually by selecting different Remote Controller Modes.
≥If the Remote Controller Mode on the Palmcorder and Remote Controller do 
not match, [REMOTE] is displayed.
Setting on the Palmcorder:
Set [REMOTE] on the [OTHER FUNCTIONS] Sub-Menu to the desired 
Remote Controller Mode.
Setting on the Remote Controller:
[VCR1]: Press the [D] Button and [∫] Button simultaneously. 
1[VCR2]: Press the [E] Button and [∫] Button simultaneously. 2
≥When the battery in the Remote Controller is replaced, the Mode is 
automatically reset to [VCR1] Mode.
MJ147-P.book  11 ページ  ２００２年４月２４日　水曜日　午後１時５６分 
						

							12
CGR-
CGR-
CGR-
CGP-
CGR-
3
21
1
CGR-D14A
B
A
B
A
A
B B
1 h 30 min.
2 h.
3 h 15 min. 2 h 10 min. 
(1 h 45 min.)
3 h 10 min. 
(2 h 30 min.)
5 h 25 min. 
(4 h 25 min.)
5 h 20 min.
10 h 10 min. 
(8 h 15 min.)
CGR-D08A/1BA
B1 h.
1 h 35 min. 
(1 h 15 min.)
CGR-D16A/1B
CGP-D28A/1B
CGR-D53A/1K
Power Supply
ªUsing the AC Adaptor
1
Insert the battery-shaped connector of the DC Cable into the 
Battery Holder on the Palmcorder.
2Connect the DC Cable to the [DC OUT] Jack on the AC 
Adaptor.
3Connect the AC Adaptor and AC Cable.
≥The AC Cable’s outlet plug cannot be pushed fully into the AC Adaptor 
Jack. A gap will remain as shown 1.
≥Before connecting or disconnecting the power supply, set the [OFF/
ON/MODE] Switch on the Palmcorder to [OFF] and make sure that 
neither [CAMERA/VCR/CARD P.B.] Lamps or Quick Start Recording 
Lamp is lit.
≥Battery cannot be charged if DC Cable is connected to AC Adapter.
ªUsing the Battery
Before use, fully charge the battery.
1Attach the Battery to AC Adaptor and charge it.
≥Since the Battery will not be charged when the DC Cable is connected 
to the AC Adaptor, disconnect it.
≥The [POWER] Lamp and [CHARGE] Lamp lights up, and charging 
starts.
≥When the [CHARGE] Lamp goes off, charging is completed.
2Attach the charged Battery to the Palmcorder.
Disconnecting the Power Source
Set the [OFF/ON/MODE] Switch 1 to [OFF], and while pressing the 
[PUSH BATT] Button 
2, slide the Battery or DC Input Lead upward to 
disconnect it.
≥When attaching or removing battery, set [OFF/ON/MODE] Switch to 
[OFF] and make sure the Operation Mode Lamp is not lit.
≥For other notes, see page 61.
~~~~~~~~~~~~~~~~~~~~~~~~
Charging Time and Available Recording Time 
A Charging Time
B Maximum Continuous Recording Time
≥“1 h 20 min.” indicates 1 hour and 20 minutes.
≥Battery CGR-D14 is supplied.
≥The hours shown in the table are approximate hours. The numeric 
characters in parentheses indicate the recording time when the LCD 
monitor is used. In actual use, the available recording time may be shorter 
in some cases.
≥The hours shown in the table are for continuous recording at a temperature 
of 68xF (20xC) and humidity of 60%. If the Battery is charged at a higher or 
lower temperature, the charging time may be longer.
1
22PUSHBAT T
1OFFONMODE
147P_text.fm  12 ページ  ２ ０ ０ ２年４月２ ４日　水曜日　午後３時３ ２分 
						

							13
1
2
3
4
1
1
2
1
2
1
Lens Cap and Grip Belt
ªAttach the Lens Cap
To protect the Lens surface, attach the Lens Cap.
1Detach the Grip Belt from the Grip Belt Holder.
2Pass the end of the Lens Cap String through the Lens Cap 
String holder.
3Pass the other end of the String through the loop made by 
the String itself and pull it toward the direction indicated by 
an arrow.
4Fit the lens cap onto the lens cap string.
≥The removed Lens Cap can be hooked onto the Grip Belt 1. (When you 
are not recording, be sure to keep the Lens Cap attached to the Lens for 
protection.)
≥Lens Cap cannot be attached when the supplied Lens Hood for Card Mode 
Picture Recording is being used.
ªAdjust the Grip Belt
Adjust the length of the Grip Belt to the size of your hand.
1
11 1Detach the tip of the Grip Belt and adjust the length of it.
2
22 2Reattach the tip of the Grip Belt.
ªTo Use as a Free Style Grip Belt
Using the Grip Belt as the Free Style Grip Belt makes it easier to handle and 
carry the Palmcorder. 1 It is also more convenient to use with the Tethered 
Remote control.
1Detach the tip of the Grip Belt from the Grip Belt Holder and 
adjust the length of it.
2Attach the Grip Belt around your wrist.
147P_text.fm  13 ページ  ２ ０ ０ ２年４月２ ４日　水曜日　午後５時１ ３分 
						

							14
Attaching the Shoulder Strap
We recommend that you attach the Shoulder Strap before going outdoors to 
record so as to avoid dropping the Palmcorder.
1Pass the tip of the Shoulder Strap through the Shoulder 
Strap Holders on the Palmcorder and pull the Shoulder 
Strap.
2Fold the tips of the Shoulder Strap, pass it through the 
Shoulder Strap Length Adjuster, and pull it.
≥Pull it out more than 1 inch (2 cm) 1 from the Shoulder Strap Length 
Adjuster so that it cannot slip off.
≥Please perform this step on the other side as well.
~~~~~~~~~~~~~~~~~~~~~~~~Inserting a Cassette
When power is supplied to the Palmcorder, the cassette can be taken out 
without turning the Palmcorder on.
1Slide the [OPEN/EJECT] Lever toward the front and pull 
down to open the Cassette Compartment Cover.
2Insert a Cassette.
3Close the Cassette Holder by pressing the [PUSH CLOSE] 
Button.
4Close the Cassette Compartment Cover.
≥For other notes, see page 61.
ªAccidental Erasure Prevention
Opening the accidental erasure prevention slider 1 on the cassette (by 
sliding it in the [SAVE] arrow direction) prevents recording. To enable 
recording, close the accidental erasure protection slider (by sliding it in the 
[REC] arrow direction.)
R E C
SAVE
1
4CLOSE
PUSH3
2
1
OPEN/EJECT
1
1
2
1
MJ147-P.book  14 ページ  ２００２年４月２４日　水曜日　午後１時５６分 
						

							15
453 2180x90x
LCD/EVF SET
PUSH MENU TO RETURNLCD BRIGHTNESS
    LOW||||----HIGH
LCD COLOR LEVEL
    LOW||||----HIGH
EVF BRIGHTNESS
    LOW||||----HIGH
12
32
1
OFFONMODE1
Turning on/off the Palmcorder and Selecting 
Modes
Turn on the power first and then select Modes.
ªHow to Turn on the Power
1
Set the [OFF/ON/MODE] Switch to [ON] while pressing the 
center Button 
1.
≥The [CAMERA] Lamp lights up.
ªHow to Switch Modes
2
Rotate the [OFF/ON/MODE] Switch.
≥With each slide of the Switch, the Mode switches in the order of Camera 
Mode, VCR Mode, and Card Playback Mode.
≥The appropriate Mode Lamp lights up.
ªHow to Turn off the Power
3
Set the [OFF/ON/MODE] Switch to [OFF] while pressing the 
center Button 
1.
~~~~~~~~~~~~~~~~~~~~~~~~~Using the Viewfinder
Before using the Viewfinder, adjust the field of view so that the displays inside 
the Viewfinder become clear and easy to read.
1Hold the Viewfinder Pull knob 1, pull out the Viewfinder and 
tilt it up.
2Adjust the Viewfinder by sliding the Eyepiece Corrector 
Knob 
2.
Using the LCD Monitor
With the LCD Monitor open, you can also record the picture while watching it.
1
11 1Set the [OFF/ON/MODE] Switch to [ON].
2
22 2Put your finger on the [OPEN 4] Tab 3 and pull the LCD 
Monitor out about 90x in the direction of the arrow.
≥The Viewfinder goes off.
3
33 3Adjust the LCD Monitor angle according to the desired 
recording angle.
≥The LCD Monitor can rotate a maximum of 180x 4 from the vertical 
position to the upward direction and a maximum of 90x 5 to the 
downward direction. Forcefully rotating the LCD monitor beyond these 
ranges will damage the Palmcorder.
Closing the LCD monitor
Push the LCD Monitor until it is securely locked.
ªAdjusting Brightness and Color Level
When [LCD/EVF SET] on the [DISPLAY SETUP] Sub-menu is set to [YES], 
the following items are displayed:
LCD Brightness [LCD BRIGHTNESS]
Adjusts the brightness of the image on the LCD screen.
LCD Color Level [LCD COLOR LEVEL]
Adjusts the color saturation of the image on the LCD screen.
Brightness of the Viewfinder [EVF BRIGHTNESS]
Adjust the brightness of the image in the Viewfinder.
1Press the [PUSH] Dial and select the item you want to adjust.
2Rotate the [PUSH] Dial and increase or decrease the number 
of the vertical bars on the Bar Indication.
≥The Bar Indication has 8 steps. A larger number of vertical bars 
indicates stronger brightness or color saturation.
Increasing the Brightness of the Entire LCD Monitor
Set the [LCD MODE] on the [DISPLAY SETUP] Sub-Menu to [BRIGHT].
≥These adjustments do not affect the recorded images.
≥For other notes, see page 69.
CAMERA
VCR
CARD 
P.B.
OFFONMODE
1, 2 3
1
MJ147-P.book  15 ページ  ２００２年４月２４日　水曜日　午後１時５６分 
						

							16
Using the Menu Screen
To facilitate the selection of a desired function or setting, this Palmcorder 
displays various function settings on menus.
1Press the [MENU] Button.
≥The Menu corresponding to the Mode selected by using the [OFF/ON/
MODE] Switch 1 is displayed.
≥When the [CAMERA] Lamp is on, the Camera Function Menu is 
displayed. 
2≥When the [VCR] Lamp is on, the VCR Function Menu is displayed. 3≥When the [CARD P.B.] Lamp is on, the Card Function Menu is 
displayed. 
4
2
Rotate the [PUSH] Dial to select a desired Sub-Menu.
3Press the [PUSH] Dial to display the selected Sub-Menu.
4Rotate the [PUSH] Dial to select the item to be set.
5Press the [PUSH] Dial to set the selected item to a desired 
Mode.
≥With each press of the [PUSH] Dial, the cursor [1] brings up a 
subsequent Mode. Menu items that cannot be used in combination with 
the selected menu items are displayed in dark blue.
≥While a Menu is displayed, you cannot begin to record or play back. Menus 
can be displayed during playback but not during recording. 
≥The above operations can be carried out using the Remote Controller. 
(l10)
≥To display the Menu, press the [MENU] Button 
5 on the Remote 
Controller.
≥To select items on the Menu, press the [ITEM] Button 
6 on the 
Remote Controller.
≥To set the mode for the selected items, press the [SET] Button 
7 
on the Remote Controller.
To Exit the Menu Screen
Press the [MENU] Button again.
About the Menu Mode Setting
The setting selected on the Menu will be retained even when the Palmcorder 
is turned off. However, if the Battery or AC Adaptor is disconnected before 
turning the Palmcorder off, the selected setting may not be retained.
(But, the setup of [EFFECT2] (l29) is not retained.)
≥Menu operation flow is shown in this text by >>.
ªFile Selection in the Card Playback Mode
A File Selection Operation may be necessary during Menu Operations. In this 
case, carry out the following procedure.
1
11 1Turn the [PUSH] Dial and select a file.
≥The selected file is marked by a frame 8.
2
22 2Press the [PUSH] Dial to confirm the selection of the file.
≥After the above File Selection Procedure, carry out the various Menu 
Operations. (The above procedure will not be repeated in the following 
instructions.)
PICTURE
No.25     100-0012
8
2CAMERA FUNCTIONS
PUSH MENU TO EXIT
1.CAMERA SETUP2.DIGITAL EFFECT3.CARD SETUP5.RECORDING SETUP6.DISPLAY SETUP7.OTHER FUNCTIONS
PUSH MENU TO EXIT
2.DIGITAL EFFECT3.CARD SETUP4.MULTI-PICTURES5.RECORDING SETUP6.AV IN/OUT SETUP7.DISPLAY SETUP8.OTHER FUNCTIONS
1.PLAYBACK FUNCTIONS
CARD FUNCTIONS
PUSH MENU TO EXIT
1.DELETE CARD FILE2.CARD EDITING3.DISPLAY SETUP4.OTHER FUNCTIONS
VCR FUNCTIONS3
4
4.MULTI-PICTURES
1
2, 3, 4, 5
1, 2
CAMERA
VCR
CARD 
P.B.
2
3
4
ZOOM
INDEX INDEX
SELECT
STORESTOP
KL∫
OSD
COUNTER
V/REW
STILL ADV
OFF/ONP.B.DIGITAL
DATE/
TIME
RESET
TITLE T
W
sVOLr¥RECMULTI/
P-IN-PPHOTO
SHOTSTART/
STOP
A.DUB
PLAY
PAUSE
FF/W
STILL ADV
MENU
ITEMSET
61 5
;ED
VAR.
SEARCHP. B .
ZOOM5
7
6
PUSHW.B./SHUTTER/IRIS/
MF/VOL/JOGMENU1
OFFONMODE
MJ147-P.book  16 ページ  ２００２年４月２４日　水曜日　午後１時５６分 
						

							17
PROG.AE   OFF 5        7    4  Ω   º
RETURN   ---- YESPROGRESSIVE AUTO ON OFFEIS
D.ZOOM  OFF     ON
  OFF 25  700
CINEMA   OFF     ON
RETURN
CAMERA SETUP
PUSH MENU TO EXIT
1)
2)
3)
4)
5)
6)
7)
8)
DATE/TIME
C.DISPLAY  LINEAR MEMORY
 T.CODE
RETURN   ---- YES OFF D/T DATE
C.RESET ---- YESDISPLAY ALL PARTIAL OFF
LCD/EVF SET ---- YESLCD MODE  NORMAL  BRIGHT
DISPLAY SETUP
PUSH MENU TO EXIT
25)
26)
27)
28)
29)
30)
13)
14)
15)
16)SCAN MODE
SPEED  FAST NORMAL SLOW
RETURN   ---- YESSTROBE MANUAL
SWING OFF      ONP-IN-P 1  2  3  4
MULTI-PICTURES
PUSH MENU TO EXIT
 WIPE MIX  STROBE
 GAIN-UP   TRAIL
 MOSAIC    MIRROR
  EFFECT1
 MONO  SOLARI  OFF MULTI P-IN-P
EFFECT2 OFF  NEGA SEPIA
RETURN   ---- YES
DIGITAL EFFECT
PUSH MENU TO EXIT
9)
10)
11)
12)
CARD SETUP
PUSH MENU TO EXIT PICTURE SIZE 
     
1280 960 640 480
RETURN ---- YES
FINE NORMAL
PICTURE QUALITY
     FINE NORMAL ECONOMY
MPEG4 MODE
----  YES
CREATE TITLE
REC-SPEED
AUDIO-REC  12bit
16bit
RETURN   ---- YES SP      LP
INDEX  2HOUR   DAYWIND-CUT  OFF     ON
RECORDING SETUP
PUSH MENU TO EXIT
17)
18)
19)
20)
 OFF     ONZOOM MIC
FLASH ON      AUTORED EYE REDUCTIONOFF ON 22)
23) 21)FLASH LEVEL
24)
s NORMAL r
REMOTE
TALLY LED   OFF    ON VCR1 VCR2 OFF
BEEP  OFF    ONSHUTTER  OFF    ON
SELF-REC  NORMAL MIRRORCLOCK-SET
  ----  YES
OTHER FUNCTIONS
PUSH MENU TO EXIT
31)
32)
33)
34)
35)
36)
 
37)
VOICE POWER SAVE OFF ON
RETURN   ---- YES
List of Menus
The illustrations of the Menus are for explanation purposes only, and they are 
different from the actual Menus.
Camera Mode Main-Menu [CAMERA FUNCTIONS]
[CAMERA SETUP] Sub-Menu
1) Auto Exposure Mode [PROG.AE] (l 25)
2) Progressive PhotoShot Mode [PROGRESSIVE] (l 22)
3) Digital Effect Image Stabilizer [EIS] (l23)
4) Digital Zoom [D.ZOOM] (l 23)
5) Cinema-like Format Recording [CINEMA] (l24)
6) Returning to the Main-Menu [RETURN]
[DIGITAL EFFECT] Sub-Menu
7) Digital Effects 1 [EFFECT1] (l 29)
8) Digital Effects 2 [EFFECT2] (l 29)
[CARD SETUP] Sub-Menu
9) Picture Size [PICTURE SIZE] (l37)
10) Picture Quality [PICTURE QUALITY] (l 38)
11) MPEG4 Picture Quality [MPEG4 MODE] (l 39)
12) Title Creation [CREATE TITLE] (l 43)
[MULTI-PICTURES] Sub-Menu 
13) Multi-Picture Mode [SCAN MODE] (l 30)
14) Strobe Multi-Picture Speed [SPEED] (l 30)
15) Swing Mode [SWING] (l 30)
16) Position of Small Picture inside Normal Picture [P-IN-P] (l 30)
[RECORDING SETUP] Sub-Menu
17) Recording Speed Mode [REC-SPEED] (l 20)
18) Audio Recording Mode [AUDIO-REC] (l 20, 36)
19) Index Mode [INDEX] (l 33)
20) Wind Noise Reduction [WIND-CUT] (l 25)
≥If this function is set to [ON], the sound of wind hitting the microphone 
can be reduced for recording.
21) Zoom Microphone [ZOOM MIC] (l22)
22) Flash [FLASH] (l28) 
23) Red Eye Reduction [RED EYE REDUCTION] (l28) 
24) Flash Level [FLASH LEVEL] (l28)
[DISPLAY SETUP] Sub-Menu
25) Date and Time Indication [DATE/TIME] (l 60)
26) Counter Display Mode [C.DISPLAY] (l 60)
27) Counter Reset [C.RESET] (l 70)
≥Set the counter value to zero. However, it cannot reset the Time Code.
28) Display Mode [DISPLAY] (l 60)
29) LCD Brightness [LCD MODE] (l 15)
30) LCD and Viewfinder Adjustment [LCD/EVF SET] (l 15)
[OTHER FUNCTIONS] Sub-Menu
31) Remote Controller Mode [REMOTE] (l 11)
32) Recording Lamp [TALLY LED] (l 21)
33) Beep Sound [BEEP] (l61)
34) Shutter Effect [SHUTTER] (l 22)
35) Date and Time Setting [CLOCK-SET] (l 20)
36) Self-Recording [SELF-REC] (l 21)
37) Voice Power Save [VOICE POWER SAVE] (l65)
MJ147-P.book  17 ページ  ２００２年４月２４日　水曜日　午後１時５６分 
						

							18
BLANK SEARCH    ---- YES
RETURN    ---- YESRECORD TO CARD  ---- YES
PLAYBACK FUNCTIONS 
PUSH MENU TO EXIT INDEX        PHOTO SCENE
AUDIO OUT    STEREO  L RAUDIO  ST1 ST2 MIX
2) 1)
3)
4)
6)
7)
8)
9)
OTHER FUNCTIONS
PUSH MENU TO EXIT REMOTE   VCR1 VCR2 OFF
RETURN          ---- YES
CLOCK-SET     ---- YES
RECORDING SETUP
PUSH MENU TO EXIT REC-SPEED  SP      LP
AUDIO-REC  12bit  
   16bit
RETURN          ---- YES
DISPLAY SETUP
PUSH MENU TO EXIT DATE/TIME OFF D/T DATE
C.DISPLAY LINEAR MEMORY
          T.CODE
C.RESET    ---- YES
DISPLAY  ALL PARTIAL OFF
RETURN          ---- YES
REC DATA  OFF     ON
LCD MODE  NORMAL  BRIGHT
LCD/EVF SET   ---- YES
15)
16) 10)
11)
5)
CARD SETUP
PUSH MENU TO EXIT PICTURE QUALITY
     FINE NORMAL ECONOMY
RETURN ---- YES
MPEG4 MODE
FINE NORMAL
----  YESCREATE TITLE
DIGITAL EFFECT
PUSH MENU TO EXIT RETURN     ---- YES
EFFECT    OFF    ONEFFECT SELECT
   OFF    MULTI WIPE MIX
   STROBE NEGA   SEPIA
   MONO   TRAIL  SOLARI
   MOSAIC MIRROR
AV IN/OUT SETUP
PUSH MENU TO EXIT AV JACK
RETURN   ---- YES
  OFF   ONMIC AV IN
IN/OUT OUT/PHONES
A.DUB INPUT
DV OUT
17)
18)
19)
20)
12)
13)
14)SCAN MODE
SPEED  FAST NORMAL SLOW
RETURN   ---- YESSTROBE MANUAL
SWING OFF      ON
MULTI-PICTURES
PUSH MENU TO EXIT
VCR Mode Main-Menu [VCR FUNCTIONS]
[PLAYBACK FUNCTIONS] Sub-Menu
1) Blank Search [BLANK SEARCH] (l 32)
2) Recording to Card [RECORD TO CARD] (l38)
3) Index Search Mode [INDEX] (l 33)
4) Audio Selector [AUDIO] (l 36)
5) Audio Output Mode [AUDIO OUT] (l 64)
6) Returning to the Main-Menu [RETURN]
[DIGITAL EFFECT] Sub-Menu
7) Digital Effect On/Off [EFFECT] (l 34)
8) Digital Effect Selection [EFFECT SELECT] (l 34)
[CARD SETUP] Sub-Menu
9) Picture Quality [PICTURE QUALITY] (l 38)
10) MPEG4 Picture Quality [MPEG4 MODE] (l 40)
11) Title Creation [CREATE TITLE] (l 43)
[MULTI-PICTURES] Sub-Menu 
12) Multi-Picture Mode [SCAN MODE] (l 35)
13) Strobe Multi-Picture Speed [SPEED] (l 30, 35)
14) Swing Mode [SWING] (l 35)
[RECORDING SETUP] Sub-Menu
15) Recording Speed Mode [REC-SPEED] (l 20)
16) Audio Recording Mode [AUDIO-REC] (l 20, 36)
[AV IN/OUT SETUP] Sub-Menu 
17) AV Jack [AV JACK] (l36, 46, 63)
18) Audio Dubbing Input [A.DUB INPUT] (l36)
19) AD Conversion Output [DV OUT] (l47)
[DISPLAY SETUP] Sub-Menu
20) Camera Data [REC DATA]
≥If you set [REC DATA] to [ON], the settings (shutter speed (l26), iris 
(l26) and white balance settings (l27), etc.) used during the 
recordings are displayed during playback. [---] appears on the display 
when there is no data.
≥The settings information may not displayed properly if the camera data 
of this Palmcorder are played back on other equipment.
The camera data will not be recorded in the following cases:
≥When the data are recorded from a card to a tape.
≥When recording proceeds with no input signals supplied.
≥When recording involves the use of the S-Video or AV Input Jack.
≥When pictures with no camera data are recorded using the DV 
Terminal.
≥When displaying a list of titles.
All of the other items on the [DISPLAY SETUP] Sub-Menu are the same as 
those on the [DISPLAY SETUP] Sub-Menu of the [CAMERA FUNCTIONS] 
Main-Menu.
[OTHER FUNCTIONS] Sub-Menu
≥Same as described on page 17.
MJ147-P.book  18 ページ  ２００２年４月２４日　水曜日　午後１時５６分 
						

							19
Card Playback Mode Main-Menu [CARD FUNCTIONS]
[DELETE CARD FILE] Sub-Menu
1) Selecting and deleting a File [DELETE FILE BY SELECTION] (l 44)
2) Deleting All Files [DELETE ALL FILES] (l 44)
3) Selecting and Deleting a Title [DELETE TITLE BY SELECTION] (l 44)
[CARD EDITING] Sub-Menu
4) Recording to Cassette [RECORD TO TAPE] (l 41)
5) Searching a File [FILE SEARCH] (l 41)
6) Setting the Lock [FILE LOCK] (l 44)
7) Setting a Slide Show [SLIDE SHOW] (l42)
8) Setting DPOF [DPOF SETTING] (l 45)
9) Formatting a Card [CARD FORMAT] (l 45)
[DISPLAY SETUP] Sub-Menu
≥Same as described on page 17.
[OTHER FUNCTIONS] Sub-Menu
≥Same as described on page 17.
Short-Cut Menus of the Card Playback Mode
 A
If you use the Short-Cut Menu, the Card Playback Mode Menu can be called 
up quickly. Press the [PUSH] Dial to display the Short-Cut Menu, and turn the 
[PUSH] Dial to select the desired Menu.
10) [FILE SEARCH]:
The [FILE SEARCH] Menu for finding files by number appears. (l41)
11) [DELETE FILE]:
The [DELETE FILE] Menu for deleting the file being displayed appears. 
(l44) Use this Menu after the file to be erased appears.
12) [FILE LOCK]:
The [FILE LOCK] Menu to prevent the accidental erasure of files (Lock 
Setting) being displayed appears. (l44) Use this Menu after the file to 
be locked appears.
13) [DPOF SETTING]:
The [DPOF SETTING] Menu for performing the DPOF settings for the 
displayed picture appears. (l45) Use this Menu after the picture whose 
DPOF settings are to be performed has appeared.
14) [EXIT]:
For terminating the Short-Cut Menu.
PUSH MENU TO EXIT RETURN          ---- YES
DISPLAY SETUP
PUSH MENU TO EXIT DATE/TIME OFF D/T  DATE
C.DISPLAY LINEAR MEMORY
          T.CODE 
C.RESET    ----   YES
DISPLAY  ALL PARTIAL OFF
LCD MODE  NORMAL  BRIGHT
LCD/EVF SET   ---- YES
DPOF SETTING    ---- YES
CARD EDITING
PUSH MENU TO EXIT RECORD TO TAPE  ---- YES
FILE SEARCH     ---- YES
RETURN          ---- YES
RETURN            ---- YES
FILE LOCK       ---- YESSLIDE SHOW      ---- YES
CARD FORMAT     ---- YES
DELETE CARD FILE1.DELETE FILE
BY SELECTION2.DELETE ALL FILES3.DELETE TITLE
BY SELECTION
1)
2)
3)
4)
5)
6)
7)
8)
9)
10)
11)
12)
13)
14)
FILE SEARCH
DELETE FILE
FILE LOCK
DPOF SETTING
EXIT
A
RETURN          ---- YES
OTHER FUNCTIONS
PUSH MENU TO EXIT REMOTE    VCR1 VCR2 OFF
CLOCK-SET  ----     YES
VOICE POWER SAVE OFF  ON
MJ147-P.book  19 ページ  ２００２年４月２４日　水曜日　午後１時５６分 
						

							20
CLOCK-SET
PUSH MENU TO RETURNYEAR  :2002
MONTH :OCT
DAY   :20
HOUR  : 8PM
MINUTE:46
1, 3 1, 2
PUSHW.B./SHUTTER/IRIS/
MF/VOL/JOG
MENU
CAMERA FUNCTIONS
PUSH MENU TO EXIT
1.CAMERA SETUP2.DIGITAL EFFECT3.CARD SETUP4.MULTI-PICTURES5.RECORDING SETUP6.DISPLAY SETUP7.OTHER FUNCTIONS
1
2
AUDIO-REC 
REC-SPEED
AUDIO-REC  12bit
RETURN   ---- YES SP      LPINDEX  2HOURWIND-CUT  OFF
RECORDING SETUP
PUSH MENU TO EXIT ZOOM MIC
 ON
REC-SPEED
 12bit    16bit
RETURN   ---- YES
 SPINDEX  2HOURWIND-CUT  OFF
RECORDING SETUP
PUSH MENU TO EXIT ZOOM MIC
 ON
FLASH ONRED EYE REDUCTION
OFFFLASH LEVELNORMAL
FLASH ONRED EYE REDUCTION
OFFFLASH LEVELNORMAL
Setting Date and Time
1Press the [MENU] Button and rotate the [PUSH] Dial to select 
[OTHER FUNCTIONS] >> [CLOCK-SET] >> [YES].
2Rotate and press the [PUSH] Dial to select [YEAR]/[MONTH]/
[DAY]/[HOUR]/[MINUTE] and set it to a desired value.
≥Year will cycle in the order shown below.
2000 ) 2001 ) ... ) 2089 ) 2000 ) ...
3Press the [MENU] Button to finish setting the date and time.
≥The clock operation starts from [00] seconds.
≥The menu will disappear when the [MENU] button is pressed again.
≥It is possible that the built-in clock in the Palmcorder may become 
inaccurate. Please check the time before recording. If the [0] Indication is 
flashing, charge the built-in lithium battery and reset the date and time.
~~~~~~~~~~~~~~~~~~~~~~~~Internal Lithium Battery Recharge
The internal lithium battery sustains the operation of the clock. When the [0] 
Indication 1 is lit, the internal lithium battery is near exhaustion.
1Connect the AC Adaptor to the Palmcorder with the power 
turned off and then connect to the AC Jack.
≥After charging for 4 hours, the built-in lithium battery can power the 
clock for approximately 3 months.
~~~~~~~~~~~~~~~~~~~~~~~~LP Mode
A desired recording speed can be selected with [REC-SPEED] on the 
[RECORDING SETUP] Sub-Menu. 1
If LP Mode is selected, the recording time becomes 1.5 times longer 
than that of SP Mode.
Although the image quality does not decrease with the LP Mode recording, 
mosaic-like noise patterns may appear on a playback image, or some normal 
functions may be restricted.
≥The contents that are recorded in LP Mode are not completely compatible 
with other equipment.
≥Audio Dubbing is not possible with LP Mode. (l 36)
~~~~~~~~~~~~~~~~~~~~~~~~Audio Recording Mode
The sound quality of the recorded sound can be selected with [AUDIO-REC] 
on the [RECORDING SETUP] Sub-Menu. 2High sound-quality recording is possible with “16bit 48kHz 2 track” Mode. 
With the “12bit 32kHz 4 track” Mode, the original sound can be recorded on 
2 tracks in stereo, while the other 2 tracks can be used for re-recording.
1
1
MJ147-P.book  20 ページ  ２００２年４月２４日　水曜日　午後１時５６分