Panasonic Pv Dv202 Operating Instructions Manual

41
Digital Features
Digital Features
VCR mode
1Set POWER to VCR.
2Press MENU to display the VCR
MENU screen.
3Rotate JOG KEY to select PLAY
 FUNCTION , then press JOG KEY
to display the VCR PLAY FUNCTION
menu screen.
4Rotate JOG KEY to select D.ZOOM ,
then press JOG KEY to select ON.
Press MENU twice to exit.
5Press  (PLAY) to start playback.
The center portion of the image
doubles in size.
6Repeat steps 2~4 to select OFF to
cancel this feature.
5PLAY
Color recording of video or still images onto
the...

42For assistance,  please call :  1-800-211-PANA(7262) or send e-mail to : [email protected]
Digital Features
EIS ON NORMAL
1Set POWER to CAMERA.
2Press EIS to stabilize the picture.
Picture flicker may be observed when
taping under fluorescent lighting
conditions.
The EIS indicator flashes when the
light level is inadequate.
Turn D.E.I.S. OFF during recording
when using a tripod.
3Press REC/PAUSE to start recording.
4Press EIS again to cancel.
 Be sure that D.E.I.S. is turned off
when...

43
Digital Features
Digital Features
1Set POWER to CAMERA or VCR.
2Press MENU to display the menu
screen.
3Rotate JOG KEY to select
 D.FUNCTION in the CAMERA mode
menu screen or PLAY FUNCTION in
the VCR mode menu screen, then
press JOG KEY to display the
CAMERA FUNCTION or VCR PLAY
FUNCTION menu screen.
4Rotate JOG KEY to select
 D.FUNCTION , and then press JOG
KEY repeatedly to select one of the
Digital Functions listed on the left.
5To cancel the Digital Function, press
JOG KEY repeatedly to select...

44For assistance,  please call :  1-800-211-PANA(7262) or send e-mail to : [email protected]
Editing Features
External Microphone
with M3 connector (not
supplied)
External
Microphone Jack
(PV-DV402 only) The original sound can be replaced with
new sound using the built-in Palmcorder
microphone or an external microphone
(PV-DV402 only).
Audio Dubbing using the
External (PV-DV402 only) or
Built-in Microphone
1Set POWER to VCR.
With the Remote Control, you can set
the Palmcorder to stop...

45
Editing Features
Editing Features
4Press  (PAUSE) to start Audio
Dubbing.
Connect the Palmcorder to the TV in
order to monitor the sound.
(p. 39)
Only NTSC (National Television Standards
Committee) recorded tapes can be audio
dubbed. The following screen appears if
the tape was not recorded in NTSC format.
5Press  (PAUSE) to stop Audio
Dubbing. To listen to the desired audio sound, set
the AUDIO setting of the VCR mode MENU
(Menu OSD: p. 110) as follows:
If the microphone used for dubbing gets
too...

46For assistance,  please call :  1-800-211-PANA(7262) or send e-mail to : [email protected]
Editing Features
Video In
S-Video In
VHF Connecting
Cable (not
supplied)TV
(To View)
A/V Cable
(Supplied)
To Audio In
To Video In
Recording:
VCR (Rear)
To S-Video In
(If there is S-Video In)
For technical reasons, dubbing a tape
may reduce its quality.
Press DISPLAY ON TV on the
Palmcorder Remote Control to eliminate
EVF/LCD Monitor indications.
If the Time Code is displayed in the EVF
or LCD...

47
Editing Features
Editing Features
3, 4PLAY
3, 4, 5PAUSE3, 4PLAY
6STOP
4REC High quality digital-to-digital copying can
be accomplished if both Palmcorders
incorporate the DV Input/Output (i.LINK)
Connector (DV interface cable (i.LINK) is
not supplied).
1Insert a pre-recorded tape into the
source (playing) Palmcorder, and set
POWER to VCR.
2Insert a blank tape with the record
tab closed into the target (recording)
Palmcorder and set POWER to VCR.
3Press  (PLAY) on the source
Palmcorder. When the tape...

48For assistance,  please call :  1-800-211-PANA(7262) or send e-mail to : [email protected]
Card Features
You can record still images to a Memory
Card.
1Slide the M-CARD Lock Switch to
unlock, then set POWER to M-CARD.
The POWER lamp lights red.
Be sure POWER is fully turned to
M-CARD position.
“PLAY: PUSH PLAY KEY” is
displayed for 10 seconds. (p. 50)
2Press MENU to display CARD
SETTING menu, then press JOG KEY
to select NORMAL or FINE .
Press MENU to exit this menu.
3Press PHOTOSHOT...

49
Card Features
1Repeat steps 1 and 2 on page 48.
2Set POWER to VCR.
3Press  (PLAY) to start playback of
the cassette tape. And then, press 
(PAUSE) to select an image.
4Press PHOTOSHOT to record the
desired image to the Memory Card.
When PHOTOSHOT is pressed in
PLAY or SLOW mode, the screen
goes to STOP mode.
To playback the images of the
Memory Card, see page 50.
When Variable Speed Search is
done (p. 35), this feature can
not be used.
5Repeat steps 3~4 to record another
image to the Memory Card....

50For assistance,  please call :  1-800-211-PANA(7262) or send e-mail to : [email protected]
1Slide the M-CARD Lock Switch to
unlock, then set POWER to M-CARD.
“PLAY: PUSH PLAY KEY” is
displayed for 10 seconds.
2Press  (M-PLAY) to display the Multi
playback screen.
“PLEASE WAIT” appears on-screen.
Rotate JOG KEY to scroll through
Multi image screen pages (6 images
per page) and select an image.
The selected image is underlined in
green.
Press MENU to display CARD
SETTING menu screen....