Panasonic System Controller Wv Cu161c Operating Instructions

							31
Notes:
•Alarm display On/Off and Buzzer On/Off mode can be
selected. (See page 20 and 21.)
•The camera or receiver control can be continued even
when an alarm is generated.
Alarm Reset
Automatic or manual resetting can be selected.
When the alarm is reset, [ALARM] disappears from the
monitor screen and the alarm reset signal is output to the
time lapse VCR.
Automatic Reset
The alarm is automatically reset after the programmed
alarm output time has elapsed.
The alarm indicator changes from blinking to steady light,
and [ALARM] disappears from the monitor screen.
Press the ALARM RESET/SUSPEND button to turn off the
steady light.
Note:Alarm can also be reset by input of the alarm recover
signal (no-voltage contact) from the time lapse VCR.
The reset mode in this case is the same as for automat-
ic reset.
Manual Reset
Press the ALARM RESET/SUSPENDbutton.
The alarm indicator goes off, [ALARM] disappears from the
monitor screen, and alarm is reset.
Alarm Suspend
The alarm suspension function allows you to suspend the
alarm function while setting up the camera or the WV-
CU161C.
1. Press the ALARM RESET/SUSPENDbutton while the
SHIFT indicator is lit.
The ALARM SUSPENDindicator lights up.
Alarm input is ignored while the ALARM SUSPEND indi-
cator is lit.
2. To cancel the alarm suspension, press the ALARM
RESET/SUSPENDbutton while the SHIFT indicator is
lit.
The ALARM SUSPENDindicator goes off.
ALARM CONTROL FUNCTIONS
When the WV-CU161C receives an alarm signal from a
camera site, an alarm is activated. The WV-CU161C can
handle the following alarms.
Camera Site Alarm
Coaxial Multiplex Communication:
Alarm is multiplexed with video signals from the cam-
era.
RS-485 Site Communication
Alarm is transmitted via RS-485.
Terminal Alarm
Alarm is input via the alarm input terminal on the rear
panel from external devices such as sensors.
Alarm Operation
[ALARM] appears on the monitor screen when the alarm
signal is supplied in the Alarm On mode
The alarm indicator starts to blink and the buzzer sounds.
(ALARM BUZZER is preset to ON at the factory.)
If the preset number is set for the ALARM PRESET or
ALARM TERMINAL parameter in ALARM SETUP menu,
then the camera moves to the preset position when an
alarm is activated. The camera picture at that position is
displayed on the monitor.
The alarm output signal is supplied to the time lapse VCR
until the alarm is reset.
RESET
SUSPENDALARMCharacter display
(ALARM DISPLAY ON)
ALARM
RESET
SUSPENDALARM
SHIFT
OPERATE ALARM
ALARM
Blinking: Alarm has been activated.
Light on: Alarm has been reset automatically
, 
or by input signal from external devices 
(when the alarm switch is in the upper position).
Light off: Alarm has been reset manually, or the 
ALARM RESET/SUSPEND button has
been pressed while the alarm indicator is on. 
						

							32
PRESET/SET/PROGRAM PRESET
To enter a submenu.
HOME/ESC button:
To return to the previous menu.
CAMERA SETUP
The camera setup operations are available using the WV-
CU161C controller on the CAMERA SETUP menus.
For further information, refer to the Operating Instructions
for the individual combination cameras.
Camera Setup
1. Hold down the CAMERA SETUP/SETUP/PROGRAM
button for 2 seconds or more to access the Camera
Setup menu. The CAMERA SETUPindicator lights up.
2. Select an item and parameter by pressing numeric but-
tons 2, 4, 6and 8.
3. Press the PRESET/SET/PROGRAM PRESETbutton to
execute the parameter or enter a submenu.
4. Press the HOME/ESCbutton to return to the previous
menu.
5. Hold down the CAMERA SETUP/SETUP/PROGRAM
button for 2 seconds or more to complete the Camera
Setup.
   *** SET UP MENU ***
PRESET 1*
 MAP 
 HOME POSITION
 SELF RETURN
 AUTO MODE
 AUTO PAN KEY
 DIGITAL FLIP
 LOCAL/REMOTE
 SPECIAL1
CAMERA
RS485 SET UP15
10MIN
AUTO PAN
SEQ
OFF
LOCAL
(Example of Camera Setup menu)
CAMERA
SETUP
SETUP
PROGRAM
CAMERA
SETUP
SETUP
PROGRAM
123
46
789
0
5
PROGRAM
PRESET ESC HOME
SET PRESET
PROGRAM
PRESETSET PRESET
PROGRAM
PRESETSET PRESETESC HOME
Notes:
•To display the special menu, move the cursor to [SPE-
CIAL] on the setup menu and simultaneously hold down
numeric buttons 4and 6for 2 seconds or more.
•To restore all default values, move the cursor to [CAM-
ERA RESET]* on the setup menu and simultaneously
hold down buttons 4, 5and 6for 2 seconds or more.
•The menu for restoring the camera defaults differs
depending on the camera type.
For example, [SPECIAL] for the WV-CS654, [SPECIAL
2] for the WV-CS854, and [END] for fixed cameras.
•If camera setup is started using the buttons on the cam-
era, then all future setup operations must be performed
with the buttons.
If camera setup is started using the System Controller,
then all future setup operations must be performed
using the same controller.
•For further information, refer to the Operating
Instructions for the selected camera.
Keys Used in the Camera Setup Menu
CAMERA SETUP/SETUP/PROGRAM button:
Hold down this button for 2 seconds or more to display
the camera SETUP MENU.
CAMERA
SETUP
SETUP
PROGRAM
ESC HOME
Numeric buttons:
To move the cursor.
To select modes.
28
4
6 
						

							33
Camera Patrol Learning
There are two ways of setting the camera patrol learning.
One is to use the setup menu and the other is to operate
the camera.
Follow the procedures described below to set the camera
patrol learning up while operating the combination camera.
1. Press the PATROL LEARNbutton while holding down
the PROGRAMbutton. 
[LEARNING] appears on the monitor.
Note:Pressing the PROGRAM button alone for 2 sec-
onds will change the screen to the WV-CU161C
SETUP MENU or camera SETUP MENU.
2. Operate the camera using the following controls so that
it traces the routine course that is the most frequently
patrolled. The learning is programmed for 30 seconds.
•Pan/Tilt (Joystick)
•Iris (Open/Close)
•Focus (Near/Far)
•Zoom (Tele/Wide)
•Preset position
Note:The memorized parameters may differ somewhat
depending on the camera type. Refer to the manual
included with the camera.
3. To stop the learning, press the PATROL STOPbutton
while holding down the PROGRAMbutton.
[LEARNING] appears on the monitor.
LEARNING
B/W AUTO
PATROL STOP
CAMERA
SETUP
SETUP
PROGRAM
Camera Preset Position
There are two ways of presetting camera positions. One is
to use the setup menu of the combination camera and the
other is to operate the camera.
Follow the procedures described below to set up the cam-
era preset position while operating the combination cam-
era.
1. Move the camera to the position you wish to preset
using the joystick. 
Adjust the picture using the following controls.
•Iris (Open/Close)
•Focus (Near/Far)
•Zoom (Tele/Wide)
Note:The memorized parameters may differ somewhat
depending on the camera type. Refer to the manual
included with the camera.
2. Type a number with the numeric buttons for the preset
position. The typed number appears in the CAMERA
section of the LED display.
3. Press the PRESET/SET/PROGRAM PRESETbutton
while holding down the CAMERA SETUP/SETUP/PRO-
GRAMbutton.
The position and its number are memorized for future
recall.
UP
LR
DOWN
123
46
789
0
5
PROGRAM
PRESET ESC HOME
SET PRESET
PROGRAM
PRESETSET PRESET
CAMERA
SETUP
SETUP
PROGRAM
PATROL
PLAY
PATROL LEARN
CAMERA
SETUP
SETUP
PROGRAM 
						

							34
The WV-CU161C System Controller can be reset to the
default settings as follows:
1. Turn off the Power Switch.
2. Turn on the Power Switch while simultaneously pressing
numeric buttons 2, 4and 6.
ALL RESET
3. Resetting has been completed when all LEDs light up
for a few seconds and then go off (except for the
Operate Indicator).
Note:The downloaded data for the camera remains as
it is.
123
46
789
0
5
PROGRAM
PRESET ESC HOME
SET PRESET 
						

							35
Power Source: 120 V AC, 60 Hz
Power Consumption:  6 W
Camera Input: Composite Video Signal: 1 V[p-p]/75 Ω
Alarm Input: No-voltage contact
Alarm Recover Input: No-voltage contact
Video Output: Composite Video Signal: 1 V[p-p]/75 Ω
Alarm Output: Open collector: 16 V DC, 100 mA max.
Alarm Reset Output: Open collector: 16 V DC 100 mA max.
Pulse (VCR): +5 V DC approx. 500 m sec. internally switchable
Data Input/Output: Equivalent to RS-485: 4-Line (Full-Duplex)/2-Line (Half-Duplex) switchable
Lens Control: Zoom: Tele/Wide
Focus: Near/Far/Auto Focus
Iris: Open/Close/Preset
Pan/Tilt Control: Manual Pan/Manual Tilt: 8-directions, 8-steps/4-steps (slow) speed
Auto Pan: On/Off
Random Pan: On/Off
Housing Control: Wiper: On/Off
Defroster: On/Off
AUX 1 - 2
Camera Control: Position Select: Preset Position, Home Position
Camera Patrol: Learn/Play/Stop
Electronic Zoom
Color/Black and white selectable
Camera function
Camera Setup
Camera Data Upload/Camera Data Download (Up to eight video cameras)
Alarm: Alarm Buzzer: On/Off
Alarm Title Display: On/Off
Auto Alarm Reset/Manual Alarm Reset
Alarm Suspension/Alarm Suspension Reset
Ambient Operating Temperature:–10˚C - +50˚C (14˚F - 122˚F)
Ambient Operating Humidity:  Less than 90 %
Dimensions: 330 mm (W) x 74.5 mm (H) x 221 (D) mm
13” (W) x 2-15/16” (H) x 8 11/16” (D)
Weight: 2.4 kg(5.3 lbs.)
Dimensions and weight are approximate.
Specifications are subject to change without notice.
SPECIFICATIONS 
						

							N1201-0 V8QA5895AN Printed in Japan
N19 2001 © Matsushita Communication Industrial Co., Ltd.  All rights reserved.Panasonic Canada Inc.
5770 Ambler Drive, Mississauga,
Ontario, L4W 2T3 Canada (905)624-5010
Panasonic Sales Company
Division of Matsushita Electric of Puerto Rico Inc.
Ave. 65 de Infanteria. Km. 9.5
San Gabriel Industrial Park, Carolina,
Puerto Rico 00985 (809)750-4300
Panasonic Security and Digital Imaging Company
A Division of Matsushita Electric Corporation of America
Executive Office:One Panasonic Way 3E-7, Secaucus, New Jersey 07094
Regional Offices:
Northeast: One Panasonic Way, Secaucus, NJ 07094 (201) 348-7303
Southern: 1225 Northbrook Parkway, Suite 1-160, Suwanee, GA 30024 (770) 338-6838
Midwest: 1707 North Randall Road, Elgin, IL 60123 (847) 468-5211
Western: 6550 Katella Ave., Cypress, CA 90630 (714) 373-7840