Panasonic Th 152ux1 Operating Instructions

							35
3D Settings
If the 3D images are not displayed correctly or seem unusual, please adjust and setup the 3D settings.
• 3D Picture Display
3D  2D
3D: Use of 3D Eyewear. You can see 3D images for 3D image signal and 2D images for 2D image signal.
2D: No use of 3D Eyewear. You can see 2D images instead of 3D images.
When set to “3D”, “3D” is displayed during 3D images.
• 3D Picture Format
3D images method is set. 
Auto: 3D images are automatically displayed according to the signal.
Side by Side/Top and Bottom: One of the formats of the 3D standard. Select these formats as necessary.
Native: Displays the input signal as it is. Use to identify the format type of the input signal.
• 3D Picture Sequence
On  Off
This function calibrates the timing to switch the right and left images as well as the timing to switch the shutter of 
right and left 3D Eyewear.
Select “On” if you feel that the sense of depth is unusual.
• Safety Precautions
Displays the precautions for viewing 3D images. 
2  access
1  select2  change
1   select
Setup menu 
Safety Precautions
3D Settings
3D Picture Format
3D Picture Sequence 3D Picture Display
3D
Auto
Off
Select the item and set.3D Settings
ScreensaverSignal
Extended life settingsInput label
Off
PC Power management
Off
Power save
Setup
OSD Language
English (
UK) Auto power off
Off
OSD Language
Select your preferred language.
   Selectable languages
Italiano Français
Deutsch
English(UK)
Español
ENGLISH(US)
.......(Chinese)
.......(Japanese)
.......(Russian) 	


PC
NANODRIFT16:9 3D
 
						

							36
Setup menu 
SIGNAL menu
Note: 
“Signal” setup menu displays a different setting condition for each input signal.
Sync
Signal
H-Freq.
V- F r e q .kHz
Hz63.98
60.02
Signal Format
1280×1024/60
[ 
RGB ]
XGA ModeAuto
Auto
 
2  access
1  select
Select the item and set.3D Settings
ScreensaverSignal
Extended life settingsInput label
Off
PC Power management
Off
Auto power off
Off
OSD Language
English (
UK) Power save
Setup
For RGB
24p SMOOTH FILM
Signal
Off
H-Freq.
Dot Clock Freq.kHz
MHz63.98
108.0 V- F r e q . H z60.02
3D 24p Film Display60Hz
[ 
Digital ]
Signal Format1280×1024/60
HDMI RangeAuto
For Digital
Input signal display 
Displays the frequency and the type of the current 
input signal.
This display is valid only for RGB / PC and Digital 
input signal.
Display range:
Horizontal 15 - 110 kHz
Vertical 48 - 120 Hz
The dot clock frequency is displayed during digital 
signal input.
• XGA Mode
This menu is displayed when the input signal is analog (PC). This unit supports three types of XGA signals with 60Hz vertical 
frequency having different aspect ratios and sampling rates (1,024 × 768 @ 60Hz, 1,280 × 768 @ 60Hz and 1,366 × 768 @ 60Hz).
Auto  1024×768  1280×768  1366×768
Auto: Automatically selected from 1024×768/1280×768/1366×768.
Switch the setting to suit the input signal for better display depends on the angle of view or display resolution condition.
Note:
After making this setting, be sure to make each adjustment (such as “Auto Setup”) on the “Pos. /Size” menu as 
necessary. (see page 22)
• Sync
This function operates only during input from PC IN terminal.
Setting RGB sync signal
Con rm that the input is set to RGB input (this setting is valid only for RGB input signal).
Auto: 
The H and V sync or synchronized signal is automatically selected. If both input, it is selected the H and V sync.
on G: Uses a synchronized signal on the Video G signal, which is input from the G connector.
VBS: Uses a synchronized signal of Composite Sync input, which is input from the HD connector.
• SDI Through
Set the active through function of the Dual Link HD-SDI Terminal Board (TY-FB11DHD).
Off 
 On
On: Enables active through.
Off: Disables active through.
Note:
Settings can only be performed for this menu when a slot mounted with a Dual Link HD-SDI Terminal Board 
(TY-FB11DHD) is selected.
• FRAME CREATION
Displays reducing screen  icker image for 50Hz/25Hz signal input.
Off 
 On
Note:
This function activates only for 50Hz/25Hz signal input with 2D images.
2  change
1  select
 
						

							37
• 24p SMOOTH FILM
During 2D or 3D viewing, images captured at 24 
frames per second are provided in a smooth manner.
Off 
 On
Note:
This function can be set only for 24p signal input with 2D 
or 3D images
• 3D 24p Film Display
For 3D images, images captured at 24 frames per second are set.
60Hz  48Hz
60Hz: Increases the number of frames to reproduce 
more natural movement images.
48Hz: Reproduces images like  lm-speci c.
Note:
This function can be set only for 24p signal input with 3D images.
Setup menu 
1Function selection
Negative image : Negative image will be displayed on the screen.
Scrolling bar only : 
A white bar will scroll from left to right. The image won't be displayed.
Overlay scrolling bar : The brightness of the image will be decreased and a white bar will scroll on it.
White screen : The whole screen will be white.
Note:
 
When the input signal is a 4k2k signal, only “Scrolling bar only” and “White screen” can be selected.
2Start setting
Select “Start”.
Screensaver 
Start
FunctionNegative image
Screensaver 
Start
Function Negative image
3D Settings
ScreensaverExtended life settingsInput label
Off
PC Power management
Off
Auto power off
Off
OSD Language
English (
UK) Power save
Setup
Signal
Screensaver
Do not display a still picture, especially in 4:3 mode, for any length of time.
If the display must remain on, a Screensaver should be used.
Screensaver 
Start
Function Negative image
 
2  access
1  select
Scrolling bar only
Overlay scrolling bar
Negative image
White screen
2  change
1  select
The menu screen will disappear and the 
SCREENSAVER will be activated. To stop the 
Screensaver under On, press any button.
Note: When the display is turned off, the 
Scrensaver will be deactivated.2  set
1  select
• HDMI Range
Switches the dynamic range according to the input signal from HDMI 1 and HDMI 2 terminals.
Video(16-235) 
 Full(0-255)  Auto
Video(16-235): If the input signal is the video range,  Example: HDMI terminal output for DVD player
Full(0-255): If the input signal is full range,  Example: HDMI terminal output for personal computer
Auto: 
Switches the dynamic range automatically between “Video(16-235)” and “Full(0-255)” according to the input signal.
Note:
This function can be set only for HDMI 1 and HDMI 2 terminal input.
• SDI Signal Format
Enabled only when the signal is input to the 4K SDI IN terminal.
Selects the format of the input signal for the 4K SDI IN terminal.
For 3,840/30p or 3,840/24p signal input:
Auto 
 YCbCr(4:4:4) 10bit  RGB(4:4:4) 10bit  YCbCr(4:2:2) 12bit  YCbCr(4:4:4) 12bit  
RGB(4:4:4) 12bit 
For 4,096/24p signal input:
Auto 
 RGB(4:4:4) 12bit  XYZ(4:4:4) 12bit
Auto: Automatically selects the signal format according to the input signal.
 
						

							38
3D Settings
ScreensaverSignal
Extended life settingsInput label
Off
PC Power management
Off
Auto power off
Off
OSD Language
English (
UK) Power save
Setup
Express settings
Custom settings
Reset
Extended life settings
30 Picture Mode
Contrast
Extended life settings
Dynamic
Side panel
NANODRIFT Saver
Lock settings Peak limitHigh
Mid
unlock
Apply to current input
Apply to all inputsOffRecommended settings
Extended life settings
Side panel
Do not display a picture in 4:3 mode for an extended period, 
as this can cause an image retention to remain on the side 
panels on either side of the display  eld.
To reduce the risk of such an image retention, illuminate 
the side panels.
This function may be applicable to the non-picture area.
  Off:   Darken both ends.
  Low:    Make it dark gray.
  Mid:   Make it gray.
  High:   Make it light gray.
Notes: 
•  To reduce the occurrence of image retention, set the Side panel to High.
•  The side panel may  ash (alternate black/white) depending on the picture being shown on the screen. Using Cinema 
mode will reduce such  ashing.side panel
4:3 Screen 
Display
image 
retention
The following settings are setup to reduce image retention:
Image Retention Reduction Menu
“Extended life settings” enables you to set the following 5 menus (Image Retention Reduction Menu) as recommended 
values or set them individually.
Picture Mode
Contrast
“Picture Mode” and “Contrast” are same as “Picture” menu items (see page 25). The settings of this menu will be 
re ected to the “Picture” menu.
Set to the recommended value
Set individually
Reset to the factory settings
Image Retention Reduction 
Menu
Setup menu 
2  access
1  select
 
						

							39
Express settings
Set the “Image Retention Reduction” menu to the recommended settings.
All menus will be locked.
   Picture Mode: Normal
      Contrast: Recommended setting for each model
   Side panel: High
   NANODRIFT Saver: Mid
   Peak limit: On
1Select “Express settings”.
Express settings
Custom settings
Reset
Extended life settings
2Select the input to apply the settings.
Apply to current input
Apply to all inputs
Extended life settings
3Select “Yes”.
Apply to current input
No Ye s
Extended life settings
2 access
1 select Peak limit
On:  Suppresses image contrast (peak brightness).
Note: When a still picture is viewed for an extended time, the screen may become slightly darker. (see page 45)
Setup menu 
NANODRIFT Saver
Moves the display position of the screen slightly to reduce image retention on the display panel. 
Low–High:  NANODRIFT Saver operates. The display position of the screen moves at set time intervals. You can set 
the screen movement range. Some of the screen may appear to be missing as a result of this operation. 
If you change the value, a mask is displayed in the range where the picture is missing as a result of 
position movement.
          Note: 
           A mask is not displayed when the input signal is a 4k2k signal.
When “NANODRIFT” Image Retention Reduction is 
operating, “NANODRIFT” is displayed.PC
NANODRIFT16:9
2 set
1 select
1 select
2 set
 
						

							40
Custom settings
Set the individual “Image Retention Reduction” menu.
1Select “Custom settings”.
Express settings
Custom settings
Reset
Extended life settings
2To set each menu to the recommended setting:
Select “Recommended settings”.
Picture Mode
Contrast
Extended life settings
Dynamic
Side panel
NANODRIFT Saver
Lock settingsPeak limit
High
Mid
Unlock
Apply to current inputApply to all inputsOff
30
Recommended settings
Each menu will be set as same 
as the “Express settings”.
3Set each menu.
Picture Mode
Contrast
Extended life settings
Dynamic
Side panel
NANODRIFT Saver
Lock settingsPeak limit
High
Mid
Unlock
Apply to current inputApply to all inputsOff
30
Recommended settings
4To lock each menu setting:
Set the “Lock settings” to “Lock”.
Picture Mode
Contrast
Extended life settings
Dynamic
Side panel
NANODRIFT Saver
Lock settingsPeak limit
High
Mid
Lock
Apply to current inputApply to all inputsOff
30
Recommended settings
Reset
Reset the “Image Retention Reduction” menu to the factory settings. Each menu will be unlocked.
1Select “Reset”.3Select “Yes”.
Express settings
Custom settings
Reset
Extended life settings
Reset current input
No Ye s
Extended life settings
2Select the input to reset the settings.
Reset current input
Reset all inputs
Extended life settings
When a menu is locked, it is grayed out and cannot 
be set.
“Picture Mode” and “Contrast” will no longer be able 
to set in the “Picture” menu, and they are labeled 
with icon to indicate their locked status. Also, 
“Normalise”, “Memory save” and “Memory load” 
are not available.
30
0
0
0
5
Picture
NormalNormalise
Brightness
Sharpness Picture Mode
Colour Contrast
Hue
Advanced settings
Memory save White balanceNormal
Memory load
Memory edit
Extended life settingsDynamic
5Select the input to apply the settings.
Picture Mode
Contrast
Extended life settings
Dynamic
Side panel
NANODRIFT Saver
Lock settingsPeak limit
High
Mid
Lock
Apply to current inputApply to all inputsOff
30
Recommended settings
6Select “Yes”.
Apply to current input
No Ye s
Extended life settings
Setup menu
2  access
1  select
2  set
1  select
2   adjust
1   select
2   adjust
1   select
2  access
1  select
2  set
1  select
2  set
1  select
1  select
2  set
1  select
2  set
 
						

							41
The input label changes as follows each time the  or  button is pressed.
 : The INPUT button press will skip its input.
Setup menu
This function can change the label of the Input signal to be displayed. (see page 15)
Customizing the Input labels
HDMI1
HDMI2
Input label
SLOT INPUT4K-SDI4K-DVI
PCHDMI1
HDMI2
SLOT INPUT
4K-SDI
4K-DVI
PC
 
Note:
The setting items are the same as the input terminal list of 
“Selecting the input signal” (page 15).
2  access
1  select
Select an input terminal and set.
3D Settings
ScreensaverSignal
Extended life settingsInput label
Off
PC Power management
Off
Auto power off
Off
OSD Language
English (
UK) Power save
Setup
2  change
1  select
(Skip)Blu-ray3
Blu-ray2 Blu-ray1Original
CATV VCR STB
DVD2 DVD1 DVD3
(Skip)
DVD4
Blu-ray4
 
						

							42
Options Adjustments
3D Settings
ScreensaverSignal
Extended life settingsInput label
Off
PC Power management
Off
Auto power off
Off
OSD Language
English (
UK) Power save
Setup
Item Adjustments
Onscreen displayOn:  Displays all the following on screen.
• Power on display
• Input signal switch display
• No signal display
• Mute and the remaining time of off-timer after 
 was pressed.
Off:  Hides all the items above from view.
Initial inputAdjusts the input signal when the unit is turned on.
Off 
 HDMI  HDMI2  SLOT INPUT*  4K-SDI  4K-DVI  PC
* “SLOT INPUT” is displayed when an optional Terminal Board is installed.
  Notes:
• Only the adjusted signal is displayed. (see page 15)
• This menu is available only when “Input lock” is “Off”.
Input lockLocks the input switch operation.
Off 
 HDMI  HDMI2  SLOT INPUT*  4K-SDI  4K-DVI  PC
*  “SLOT INPUT” is displayed when an optional Terminal Board is installed.
  Notes:
• Only the adjusted signal is displayed (see page 15).
• Input switch can be used when this is set to “Off”.
1Press to display the Setup menu.
2
Press to select “OSD Language”.
Press for more than 3 seconds.
Options
On
Onscreen displayOff
Initial input
Off
Input lock
Off
Button lock
Off
Remocon User level
Enable
Off-timer function
Mode1
Aspect Mode
Manual
Auto Setup
Off
Studio mode
3D settings
Function button assign 1Scrolling barFunction button assign 2Test patternsFunction button assign 3Blue onlyFunction button assign 4
On
3D Safety PrecautionsV-PositionH-Position00
5Press to exit from Options menu.
4 3
Press to select “Options”.
Press to display the Options menu.
Press to select your preferred menu.
Press to adjust the menu.Options
Shipping
 
						

							43
Options Adjustments
Item Adjustments
Button lockOff 
 MENU&ENTER  On 
Off:  All the buttons at the right side of the main unit can be used.
MENU&ENTER:
  Locks 
MENUMENU and ENTER/ENTER/ buttons on right side of main unit.
On:  Locks all the button on right side of main unit.
Sets Button lock with the unit buttons in the following procedure.
Off:  Press 
 four timesPress INPUT four timesPress  four timesPress ENTER/ENTER/
MENU&ENTER:  Press ENTER/ENTER/ four timesPress  four timesPress INPUT four timesPress ENTER/ENTER/
On:  Press  four timesPress ENTER/ENTER/ four timesPress  four timesPress ENTER/ENTER/
Remocon User levelOff 
 User1  User2  User3 
Off:  You can use all of the buttons on the remote control.
User1: You can only use 
, , , , , ,  buttons on the remote control.
User2: You can only use 
 button on the remote control.
User3:
 Locks all the buttons on remote control.
Off-timer functionEnable: Enables the “Off-timer function”.
Disable: Disables the “Off-timer function”.
Note: When “Disable” is set, the Off-timer is cancelled.
Aspect ModeSelect the aspect switching pattern on pressing 
 from the 3 modes.
Mode1: Aspect mode suitable for regions such as Europe and China (PAL/SECAM system)
Mode2: Aspect mode suitable for regions such as North America and Japan (NTSC system)
All Aspect: Aspect mode for all aspect options
Auto SetupSets the operational mode of the automatic position adjustment in the Pos./Size menu.
Manual:  Automatic position adjustment starts when 
 is pressed on the remote control or automatic 
position adjustment is executed from the Pos./Size menu.
Auto:    Other than remote control or menu operation, automatic position adjustment starts:
          When the display power is turned ON.
     When the input signal is switched.
Studio modeFor switching functions in setting menus used for television studio applications. 
Studio mode: On Studio mode: Off
White balance
“Studio” can be selected.  “Studio” not available. 
Studio GainCan be switched On and Off. Cannot be speci ed 
(set to “Off” and cannot be changed). 
Under scanCan be switched On and Off.Cannot be speci ed 
(set to “Off” and cannot be changed). 
Function button 
assign 1
Function button 
assign 2
Function button 
assign 3
Function button 
assign 4Set the function to operate when the FUNCTION button 1 to 4 on the remote control is pressed.
3D settings: The “3D Settings” menu is displayed.
Scrolling bar: The screen saver activates, and after 15 minutes, the display power shuts down 
(standby).
Test patterns: The test pattern is displayed by switching among seven patterns.
Blue only: The screen displays only blue color for image adjustment.
Signal: The “Signal” menu is displayed.
H-PositionWhen the input signal is a 4k2k signal, adjust the horizontal position.
V-PositionWhen the input signal is a 4k2k signal, adjust the vertical position.The four split screens respectively 
move in the horizontal direction.
The four split screens respectively 
move in the vertical direction.
 
						

							44
Pressing the FUNCTION button activates one of the following  ve functions. The settings of 
functions are performed with the “Function button assign 1” to “Function button assign 4” on 
the Options menu. (see page 43)
3D Settings / Signal
The menu screen is displayed.
(Example: 3D Settings)
Safety Precautions
3D Settings
3D Picture Format
3D Picture Sequence 3D Picture Display
3D
Auto
Off
Pressing the FUNCTION button clears the menu.
Scrolling bar / Test patterns / Blue only
Con rmation screen (Example: Scrolling bar)
The operation 
starts.
Scrolling bar
Activates the “Scrolling bar only” screensaver. After 
15 minutes, the display enters standby mode.
To exit this mode, press any button.
Blue only
The screen displays only blue color for image 
adjustment.
To exit this mode, press FUNCTION button.
Test patterns
Each time you press , a different test pattern is 
displayed (seven in all).
Color Bars Red Green
Blue Frame
(2 lines × 2 dots)
Black
1% window
To exit this mode, press any button other than .
Note:
“PC Power management” and “Auto power off” are deactivated during “Scrolling bar” or “Test patterns” operation. 
(see page 34)
Item Adjustments
3D Safety Precautions3D Safety Precautions show/hide is set during power ON.
On:  3D Safety Precaution is shown every time when the power is ON.
Off:  3D Safety Precaution is not shown when the power is ON.
When the setting changes from “On” to “Off”, the con rmation screen is displayed as below. 
Pressing “YES” switches the setting.
YES      NO 3D Safety Precautions
If Off is selected, the 3D safety precautions 
will not be displayed when power is turned on.
Change Setting?
Using FUNCTION button
Options Adjustments
Ye sNo Scrolling bar
Function 1Press to 
select 
“Yes”.
Press.
Normalization
When both main unit buttons and remote control are disabled due to the “Button lock” or “Remocon User level” 
adjustments, set all the values “Off” so that all the buttons are enabled again.
Press the 
 button on main unit together with  button on the remote control and hold for more than 5 seconds.
The “Shipping” menu is displayed and the lock is released when it disappears.