Panasonic Tv Dvd Combination Pv 9d53 Operating Instructions

							21

V-CHIP SET
CONFIRM
PASSWORD :

V-CHIP SET
NEW
PASSWORD
:
<     /     /     /     /MENU>
V-CHIP SET
LANGUAGE/IDIOMA/LANGUE
Press  or  until the OPTION
menu appears.
Setting the V-Chip
Press TV to select TV mode, then press TV MENU.
The TV menu screen will appear.
Enter the password (4 digits)
using Direct Channel Selection
(0-9), then press ENTER.
Enter the same password again
for confirmation, then press
ENTER.
Now the password is registered
and the V-Chip setting menu will
appear on the display.
NOTES:
•To avoid forgetting the password, write
it down and keep in a safe place.
•If you forget the password, turn the
volume level into a minimum, then
press VOL – on the unit and 0 on the
remote control for more than 1 secondsimultaneously.
TO REGISTER PASSWORD
This TV/DVD is equipped with a V-Chip Controller which provides you with channel viewing access
controls and restrictions. This function is to prevent your children from watching violence or sexual
scenes, that you may choose to exclude.
To use the V-Chip function, you must register a password.
1
2
4
5
 appears instead of the number.
<     /     /     /     /MENU>
V-CHIP SET
LANGUAGE/IDIOMA/LANGUE
Press  or  to select the “V-
CHIP SET”, then press 
 or .3
•If you put a wrong number, press
CANCEL.
 5E90501A P18-2321/4/03, 11:57 PM 21 
						

							22
<     /     /     /     /MENU>
MOVIE RATING
CHANGE PASSWORD V-CHIP SET
V-CHIP
TV RATING
: PG-13 : ON
: TV-Y
<     /     /     /     /MENU>
MOVIE RATING
CHANGE PASSWORD V-CHIP SET
V-CHIP
TV RATING
: PG-13 : OFF
: TV-Y
<     /     /     /     /MENU>
MOVIE RATING
CHANGE PASSWORD V-CHIP SET
V-CHIP
TV RATING
: OFF : OFF
: TV-Y
<     /     /     /     /MENU>
MOVIE RATING
CHANGE PASSWORD V-CHIP SET
V-CHIP
TV RATING
: OFF : OFF
: OFF
1
NOTES:
•The V-Chip function is activated only
on programs and tapes that have
the rating signal.
•If you are changing channels using
a VCR or a cable box, while the TV
remains on channel 3 or 4, the V-
Chip operates differently.  When you
enter your password to temporarily
release the block on any channel,
you have completely disabled the V-
Chip function for all stations.  To
reset the V-Chip turn your TV off
and back on.
•Some cable boxes are built with a
delay feature, in some cases it can
take up to 10 seconds for a program
to appear after the password has
been input.Press 
 or  to select the
“MOVIE RATING”.
TO SET THE V-CHIP
Press  or  to display the
desired setting. In the V-CHIP SET menu, press
 or  to select the “TV
RATING”.
When you select TV- Y7, TV-PG, TV-14 or TV-MA, press
DISPLAY to show the contained rating. Press 
/ or /to select the desired item you want. OFF :TV RATING is not set
TV-Y :All children
TV-Y7 :7 years old and above
TV-G :General Audience
TV-PG:Parental guidance
TV-14 :14 years old and above
TV-MA:17 years old and above
2
3
Press  or  to select desired
rating.
OFF :MOVIE RATING is not set
G:All ages
PG :Parental guidance
PG-13 :Parental guidance
less than 13 years old
R:Under 17 years old
Parental guidance suggested
NC-17 :17 years old and above
X:Adult only
4
Press TV MENU until the MENU
screen is cleared. Press 
 or  to select “V-
CHIP”.
Press 
 or  to Display “ON”.
Now your settings were set into
the memory. To use after the TV is protected
When a program is received with the
V-Chip protection applied, enter the
password. Protection can be tempo-
rarily overridden.
5
6
7
Setting the V-Chip
<     /     /     /     /MENU>
MOVIE RATING
CHANGE PASSWORD V-CHIP SET
V-CHIP
TV RATING
: OFF : OFF
: TV-Y
<     /     /     /     /MENU>
MOVIE RATING
CHANGE PASSWORD V-CHIP SET
V-CHIP
TV RATING
: PG-13 : OFF
: TV-Y
 5E90501A P18-2321/4/03, 11:57 PM 22 
						

							23
MOVIE RATING
CONFIRM
PASSWORD CHANGE PASSWORD V-CHIP SET
V-CHIP
TV RATING
: OFF
:: OFF
: OFF

MOVIE RATING
NEW
PASSWORD CHANGE PASSWORD V-CHIP SET
V-CHIP
TV RATING
: OFF
:: OFF
: OFF

<     /     /     /     /MENU>
V-CHIP SET
LANGUAGE/IDIOMA/LANGUE
<     /     /     /     /MENU>
V-CHIP SET
LANGUAGE/IDIOMA/LANGUE
<     /     /     /     /MENU>
MOVIE RATING
CHANGE PASSWORD V-CHIP SET
V-CHIP
TV RATING
: OFF : OFF
: OFF
TO CHANGE PASSWORD
Press TV to select TV mode,
then press TV MENU. The TV
menu screen will appear.
Press 
 or  until OPTION
menu appears.
Press 
 or  to select the “V-
CHIP SET”, then press  or .
Press 
 or  to select
“CHANGE PASSWORD”, then
press 
 or .
Enter the new password using
Direct Channel Selection (0-9),
then press ENTER.
Enter the new password again
for confirmation, then press
ENTER.
Press TV MENU repeatedly to
return to normal screen.
1
2
3
5
6
7
8

V-CHIP SET
PASSWORD
:
Enter the Password using Direct
Channel Selection (0-9), then
press ENTER.4
•If you put a wrong number, press
CANCEL.
 5E90501A P18-2321/4/03, 11:57 PM 23 
						

							24
<     /     /     /     /CANCEL/MENU>
BRIGHTNESS
CONTRAST0
+32
0
0
0 COLOR
TINT
SHARPNESS
<     /     /     /     /MENU>
BRIGHTNESS
CONTRAST0
+32
0
0
0 COLOR
TINT
SHARPNESS
Picture controls are factory preset but you can adjust them individually as follows:
Picture control adjustment
Press  or  until PICTURE
menu appears.Press TV to select TV mode,
then press TV MENU. The TV
menu screen will appear.
CANCELPressing CANCEL while making
picture adjustments will return all
adjustments to the factory preset
levels.
NOTE:
The CONTRAST default setting is set
to maximum at the factory.Press 
 or  to select the item
you want to adjust.
1
2
3
4
Press  or  to adjust the
setting.
5After your desired setting
changes press TV MENU until
the MENU screen is cleared.
BRIGHTNESS
CONTRAST
COLOR
TINT
SHARPNESSincrease brightness
increase contrast
brilliant color
greenish colordecrease brightness
decrease contrast
pale color
reddish color
makes picture softer
makes picture clearer
 5E90501A P24-3221/4/03, 11:57 PM 24 
						

							25
The TV/DVD is equipped with a feature known as Multi-channel TV Sound or MTS. MTS broadcasts greatly
enhance TV viewing by bringing you programs with high fidelity stereo sound.
MTS also provides an extra channel called the Second Audio Program or SAP which broadcasters can use to
transmit a second language for bilingual transmission or for other purposes.
When the TV is turned on or a
channel selection is made, make
certain the STEREO appears on
the screen. This means that
Stereo broadcasting is
available. You can enjoy stereo
sound from the left and right
speakers.
•When Mono broadcasting is
received, no indication is
displayed.
•If the broadcast signal is not
strong enough or clear stereo
sound is not available, press
AUDIO to change to mono
sound. The noise should be
eliminated. Press it again to
return to the stereo sound.
LISTENING TO SAP (SECOND AUDIO PROGRAM)
TO SELECT DESIRED SOUND
MONO+SAP BROADCASTING
SAP SOUND MONO SOUND
(MAIN)
STEREO SOUND
(MAIN)MONO + SAP SOUND
(MONO)
STEREO+SAP BROADCASTING
MONO + SAP SOUND
(MAIN)MONO SOUND
(MAIN)SAP SOUND
Stereo and second audio program (SAP)
STEREO  SAP CH  013
STEREO CH  013
When the TV is turned on or a
channel selection is made, make
certain the SAP appears on the
screen. This means that the
Second Audio Program
broadcasting is available.
Press AUDIO to select the
desired sound. LISTENING TO STEREO SOUND
SEL. STEREO
 5E90501A P24-3221/4/03, 11:57 PM 25 
						

							26
Preparation/Status display of disc
NOTE:
If the unit does not operate properly:
Static electricity, etc., may affect the play-
ers operation. Disconnect the AC power
cord once, then connect it again.
PlaylistPBC
123456780:02:31 0:53:09 1/8
T
DVD
1/11/8 Eng DolbyDigital1/8 Eng1/8
1/19TC0:07:18 2:02:31
Audio CD/Video CD To make status display disappear, press DISPLAY again.
Status display of discPress DISPLAY. The status display of the disc will appear on the
screen.
•When you play a CD disc, the status display will appear
and remain on the screen.
•When you play the Video CD, Play list will not appear on
the screen.
PreparationBefore DVD/CD operation, please make preparations as follows.
1
2
3Insert the AC cord plug into a standard 120V 60Hz polarized
AC outlet.
•If the AC cord plug is plugged in for the first time, wait for
about 5 seconds before pressing POWER.
NOTE: When connecting to other equipment, unplug the unit
from the AC outlet.
Press POWER on the unit or on the remote control to turn on
the unit. The POWER indicator will light.
•Every time you press POWER, the TV/DVD starts from TV
mode.
•When using an amplifier, switch on the amplifier.
Press DVD on the remote
control to select DVD mode.
The DVD startup screen will
appear on the screen.
Disc operation
Chapter number Title number Title elapsed playing time
Title total time
Audio language
A kind of audioSubtitle languageCamera angle
Disc operation
Track elapsed playing time
Track numberTrack total time
Play list
The following pages describe the
setup/operation in DVD mode.
PBC (PlayBack Control) on Video CD
 5E90501A P24-3221/4/03, 11:57 PM 26 
						

							27
Playback procedure
6
Press OPEN/CLOSE or
PLAY.
The disc tray closes auto-
matically.
The TV-screen,   changes
to “” and then playback
commences.
• A menu screen will
  appear on the TV screen,
  if the disc has a menu
  feature.
1Press DVD on the remote
control to select DVD
mode.
Press OPEN/CLOSE on
the unit or the remote con-
trol.
The disc tray will open.
2Place a disc onto the tray.
Position it with the printed
label side up, align it with
the guides, and place it in
its proper position.
3
Press / or /to make a selection.4
Press ENTER.
• Title is selected and play commences.5
Press STOP to end playback.
•The unit memorizes the stopped point, depending on the
disc. “
” appears on the screen. Press PLAY to resume
playback (from the scene point).
•If you press STOP again or unload the disc (“
  ” appears
on the screen.), the unit will clear the stopped point.
7Press OPEN/CLOSE.
The disc tray opens.
Remove the disc and press OPEN/CLOSE then press
POWER.
The disc tray closes and unit turns off.
NOTES:
•If a non-compatible disc is loaded, “In-
correct Disc”, “Region Code Error” or
“Parental Error” will appear on the TV
screen according to the type of loaded
disc. If these appear, check your disc
again (see pages 9 and 38).
•Some discs may take a minute or so to
start playback.
•When you set a single-faced disc label
downwards (ie. the wrong way up) and
press PLAY or OPEN/CLOSE on the
unit, “
” will appear on the display for
about 3 seconds and then “No Disc” or
“Incorrect Disc” will be displayed.
•Some playback operations of DVDs
may be intentionally fixed by software
producers. Since this unit plays DVDs
according to the disc contents the soft-
ware producers designed, some play-
back features may not be available. Also
refer to the instructions supplied with the
DVDs.
 5E90501A P24-3221/4/03, 11:57 PM 27 
						

							28
Special playback
Press SEARCH + during normal playback.
Each press of the SEARCH + will increase the speed of the
search 
 (x 2),  (x 4),  (x 8),  (x 15).
(CD: 
 (x 2),  (x 4),  (x 8),  (x 20))
• To resume normal playback, press PLAY.
Fast Forward Playback
Press SEARCH – during normal playback.
Each press of the SEARCH – will increase the speed of the
search 
 (x 2),  (x 4),  (x 8),  (x 15).
(CD:  (x 2),  (x 4),  (x 8),  (x 20))
• To resume normal playback, press PLAY.
Review Playback
Press PAUSE/STILL during
normal playback to pause play-
back.
Still Playback
To resume normal playback, press PLAY. Press PAUSE/STILL during still playback.
One frame is advanced each time you press PAUSE/STILL.
Frame Advance
• To resume normal playback, press PLAY.
• To resume the still playback, press PAUSE/STILL.
Press SLOW – Reverse or SLOW + Forward during normal
playback or still playback.
Each press of SLOW will change the speed of the slow x1/2,
x1/4, x1/6, x1/8.
Slow-motion Playback
To resume normal playback,
press PLAY.
Locating a chapter or trackNOTE:
The unit is capable of holding a still video
image or On screen display image on your
television screen indefinitely. If you leave
the still video image or On screen display
image displayed on your TV for an ex-
tended period of time, you risk permanent
damage to your television screen.  Pro-
jection televisions are very susceptible.Press SKIP + Forward or SKIP – Reverse during playback to
locate a chapter that you want to watch.
Each time you press the button, a chapter or track is skipped. Note: There may be a slight delay be-
tween when you press the button and
the function activating.
 5E90501A P24-3221/4/03, 11:57 PM 28 
						

							29
3
MP3 playback
This player can play back the MP3-data
which has been recorded on CD-R or CD-
RW. To produce the MP3-data, you need a
Windows-PC with CD-ROM drive and a MP3-
encoding Software (not supplied).
The Apple-HFS-System can not be played.
Limitations on MP3 CD playback
•MP3 CD is the disc that is standardized by
ISO9660, its file name must include 3-digits
extension letters, “mp3”.
•The directory and file names of the MP3
CD must correspond to the ISO
standardized files.
•This unit can read 200 files per disc. If
one directory has more than 200 files, it
reads up to 200 files, the remaining files will
be omitted.
•MP3 CD’s cannot be used for playback for
the purpose of recording.
•It may take more than one minute for this
unit to read MP3 files depending on its
structure.
•Music recorded by “Joliet Recording
Specification” can be played back, the file
name is displayed on the screen. Long file
names will be condensed.
•The music files recorded by “Hierarchical
File System” (HFS) cannot be played.A MP3 menu screen will appear
on the TV screen.
Press 
/ or / or Number
buttons (0-9) to select the desired
track, then press ENTER. Track
is selected and play commences.
• In case the folder includes more than 11 tracks, press 
or  to display next track list.
Notes on MP3 files
To play back MP3 CD in the recorded order,
1. Use MP3 software that records data
alphabetically or numerically.
2. Name each file including two-digit or three-
digit number (e.g. “01” “02” or “001” “002”).
3. Refrain from making too many sub-folders.
CAUTION:
•Some MP3 CDs can not be played back
depending on the recording conditions.
•The CD-R/RW that has no music data or
non-MP3 files can not be played back.
4Press STOP to end playback.
• The unit records the stopped point. “” appears on the
screen. Press PLAY to resume playback (from the scene
point).
• If you press STOP again or unload the disc, the unit will
clear the stopped point.
5Then press OPEN/CLOSE.
The disc tray opens.
Remove the disc and press POWER.
The disc tray closes automatically and the unit turns off.
1Press OPEN/CLOSE.
The disc tray will open.
Place a disc onto the tray.
2Press DVD to select the DVD
mode. Press PLAY or OPEN/
CLOSE. The disc tray closes au-
tomatically. On the TV-screen,
“Scanning...” will appear.
Scanning will take as much time
as the number of file.
MP3 CD Information
NOTES:
During MP3 Playback, you can not use SEARCH, A-B
Repeat functions.
You can use Repeat (Track or All), Random functions and
Program playback for MP3 CD Playback. (See page 31) •
•
-/18
0:00:00
/Enter/0-9/PlayMode
/01Ð02Ð03Ð04Ð05Ð
Japan
Bay Bridge
CLOSE MY EYES
DIVE TO BLUE
Honey
06ÐBLUE EYES07ÐBlurry Eyes08Ð09Ð10Ðflower
Lies and Truth-
winter fall
T
Scanning...
 5E90501A P24-3221/4/03, 11:57 PM 29 
						

							30
Zooming/Locating desired scene
1
NOTES:
•You can select the Pause, Slow or
Search playback in the zoom mode.
• Some discs may not respond to zoom
feature.This unit will allow you to zoom in on the frame image. You
can then make selections by switching the position of the
frame.
In the zoom mode press ZOOM repeatedly to return to a
1:1 view (
 Off).
1Press ZOOM during play-
back.
The center part of the
image will be zoomed in.
Each press of ZOOM will
change the ZOOM 
1
(x 2), 2 (x 3) and 3
(x 4).
2
3
Zooming
Use the title, chapter and time recorded on the disc to
locate the desired point to play back.
Press Number buttons (0–9) to input the number.
• If you input a wrong number, press CANCEL.
• Refer to the package supplied with the disc to check the
  numbers.
1Press JUMP during play-
back.
3
Locating Desired Scene
Press ENTER.4
• Playback starts.
• When you change the title, playback starts from
Chapter 1 of the selected title.
• Some discs may not work in the above operation. Press 
/// to view a different part of the frame.
You may move the frame from the center position to UP,
DOWN, LEFT or RIGHT direction.
2Press  or  to select the “C (Chapter)”, “T (Title/
Track)” or “ (Time)”.
Jump
0:00:00 / 2:02:31 1 / 8 _ _ / 19
/Enter/0   9/Cancel/Jump
 5E90501A P24-3221/4/03, 11:57 PM 30