Panasonic TV/DVD/VCR Combination AG-527DVDE Operating Instructions

31
Timer Operation
Repeat steps 1 and 2 on page 30.1
Press PROG twice to exit this mode.
2
3
To Replace program...
To Clear program...
4
Press  to select
the desired program.
1)Press SET to display.
2)
Press  to select
and press SET or
  to set new
program contents.
3)Press PROG.
Cancel a Timer Recording:
(Recording is in progress)
Hold down STOP for a few seconds
to cancel the Timer Recording.
 Any future daily or weekly recordings
will be performed as programmed.
Press ADD/DLT.
Review, Replace or...

32
Universal Remote Control is...
The Remote Control may be set up to control some
basic DSS or Cable box functions.
The Universal Remote Control Setup
1
Cable Box Universal Remote Control Feature
Press , FM, DVD or DSS CABLE on the
remote control to select the desired mode. (See below
for buttons available in each mode.)Once the remote control has been properly set up,
you can select TV-VCR, FM, DVD, DSS or CABLE
mode depending on which functions you wish to
control.
Find your DSS box or Cable box
Brand...

33
Advanced Operation
 In DSS or CABLE mode, it may be necessary to press ENTER after pressing number
keys for channel selection.
 In DSS or CABLE mode, POWER, CH Up/Down, Number Keys, ACTION, PROG,
DISPLAY/ENTER, SEARCH/SKIP-, R-TUNE, SELECT, SET, CM SKIP/ZERO/SKIP+,
COUNTER RESET/ZOOM, ANGLE, AUDIO, TITLE, SUB TITLE, MENU, or ADD/DLT are
not available. Press 
, FM, DVD to use these functions.
 Depending on your DSS receiver or Cable box brand, some of the functions listed may not
be remote...

34
Search System is ...Each time a recording is made, an invisible index mark is placed on the tape.
When timer recordings are made, program index and information are also included.
These index marks can be used to access or scan recordings.
Tape Operation
1
Press SEARCH*
in Playback or
Stop mode to
display INDEX
SEARCH screen,
and then press
number keys
to select the
recording number.
 To calculate
number, see below.
Press FF or REW
to start search.
Index Search
Go directly to the desired recording.
...

35
Advanced Operation
Program End Search
Locates end point of recording for continuity.
Press SEARCH twice in Playback or
Stop mode to display PROGRAM
END SEARCH screen .
1
SEARCH  START : FF
EX
 I T    :   SEARCH   
PROGRAM END SEARCHPress FF
to start search.
Example of Program End Search operation.
Fig.1
Fig.2
Fig.3If search exceeds a few seconds in BLANK area.
  PLAYBACK DIRECTIONProgram 1
Program 2 or BLANKINDEX
Program 2 
BLANKINDEXBLANKProgram 1 
         Program 2
BLANK         Program 1INDEX...

36
Tape Operation (continued)
Repeat Play
Set to see a recording over and over.
Zero Search
To quickly return to a specific tape counter location.
1
2
Press STOP.4
53
Continue playback, rewind, or
fast forward.
Press COUNTER
RESET at the
desired position to
reset to “0:00:00.”
Press DISPLAY* during playback
to display the Counter.
Press CM/ZERO in stop mode to
start ZERO SEARCH.
0 : 00 : 00SLP
PLAY  12 : 00   PM
PLAY REPEAT  ON
To turn “ON,”
press PLAY/REPEAT on the unit
repeatedly in Play mode to...

37
Advanced Operation
Press CM/ZERO repeatedly to select skip
time in Playback mode.
Commercial Skip
By pressing the CM/ZERO button in Playback mode
you can skip over 1 to 3 minutes of recorded tape in
just a few seconds.
 No indication appears.
 

 


Auto Shut Off
No broadcast signal in TV mode (Only when
Weak Signal Display is set to OFF.), DVD
stops, or blank tape is played for 5 minutes
➛ Power turns off
 This feature is canceled if any button is
pressed during above conditions.

 

 


Auto...

38
ANTENNA  :   CABLE
AUTO   SETCHANNEL  CAPT I ONWEAK  S I GNAL   D I SPLAY : OFF
SELECT :          SET       : SET      
END       : ACT I ON   
           SET  UP  CHANNEL  
1
2
Press ACTION*
to display MAIN MENU.
Channel Caption
1)Press   to
select “CH.”
2)Press SET to
display SET UP
CHANNEL screen.
3
1)Press  to select
CHANNEL CAPTION.
2)Press SET to
display  screen.
5
Press ACTION three times
to end setup.
Special VCR  Features
4- -
- -
- -
- -
CHANNEL  CAPT I ON  
SELE
CT :          SET       :...

39
Advanced Operation
Remote Warning Feature
1
Press ACTION twice
to return to normal screen.
When Universal Remote Control (page 32) is
used, and this feature is set to “ON,” a warning
appears whenever an invalid key is pressed in
DSS or Cable mode.
2
43
Press ACTION
to display MAIN MENU.
1)Press 
  to
select “TV.”
2)Press SET to
display SET UP
TV screen.
1)Press 
 to
select REMOTE
WARNING.
2)Press SET to
set “ON” or
“OFF.”
“REMOTE WARNING : OFF”
➛Remote warning will not appear
even if invalid key is...

40
V-Chip Control Feature
Press ACTION*
to display MAIN MENU.
Enter Secret Code
A 4-digit code must be entered to view a blocked
program or change rating settings.
1
 Some rental movies do not
include V-Chip data.
 DO NOT forget your secret code.
 Once ratings are set, restricted
tapes or programs cannot be
accessed unless the secret code
is entered.Changing your secret code
 You will need your current code.
Do steps 1 ~ 3. In step 4, press CLEAR
to clear current code.
Repeat steps 3 and 4 to enter...