Panasonic Ventilating Fan Fv-11vh2, Fv-11vhl2 Installation Instructions

I
II
III
Maintenance     (Cleaning) I
Maintenance     (Replacement of lamp) IIM
od el N o.F V -1 1 V H 2
F V -1 1 V H L2
 Ventilating Fan
Thank 
you very muc h for having  purchas ed our Ventilating  Fan.
FV -1 1V H 2FV -1 1V H L2 back cover back cover 

The Panasonic ceilin g moun t ventilating fa ns uses a siro cco fan  driven by a capacito r motor. The moto r is
design ed to h ave an extend ed service life with  reduce d energy con sumption. It a lso incorpora tes a
therma l cut-off  for safety. The gri lle covering the main body  is a spring-loaded,  quick-r elease type. A
dampe r for preventin g counterflow is prov ided. Th e blower uses  a high-capacity sirocco fan  develo ped to 
reduce  the no ise level.
The he ater for this u nit is a 1400 W...

Ventilating unitDIME
NSIONS
2 1 /8  ( 5 4.8 )
14 ( 3 57.8 )
 18 1/8 (460)
2
 1 /2  ( 6 2)
11  7 /8  ( 3 01)13 1 /4  ( 3 37.8 )
 7 5/8 (195)
5 (128.7)
1
1  1 /4  ( 2 85.5 )
 18 1/8 (460)
7
 3 /4  ( 1 96)1 ( 2 5)
 16 (407)
19 1/2 (497) 19 1/2 (497)
16 (407)
1 1  1 /4  ( 2 85.5 )
 5 (128.7)
7
 3 /4  ( 1 96)
 7 5/8 (195)
2
 1 /2  ( 6 2)
11  7 /8  ( 3 01) 

1540
3. This product must be
 properly grounded. Noise
Vent
(sone)
0.6
0.7 Only for FV-1
1VHL2. AC 120V, 60Hz.SPE
CIFIC ATION S
GENERAL SAFE TY INFO RMATION 650
720
29.5
Exhaust &
Circulation
10.  This product (FV-1 1VHL2) has a fluorescent lamp that contains mercury. Disposal may be re\
gulated in your 
       community due to environmental considerations. For disposal or re\
cycling information, please contact your 
       local authorities or the Electronics Industries Alliance:http://w\
ww.eiae.org...

GENERAL SAFE TY INFO RMATION  CON TINUED
Circulating fan unit
Red
White Black
Moto r(C)
 White
Thermal cut-off
oo
(230 F (110 C))
Heater
(1400W)
Th erm ostat
o o
(14 0F ( 60C))
 Fuse
(20A)
Ventilating fan unit Red
White
Black
Moto r(V)Capac itor
Bla ckW hit eW hit eB la ck
 Junction box
Green
Earth ground Power Supply
AC120V 60Hz
Sw it c h (n ot
i n clu ded)S w it c h (n ot
i n clu ded)
WIRI NG D IAGR AM
WARNING:
T o reduce the risk of fire, electric shock or injury to persons, observe \
the following:...

Fig.2-2 Fig.2-1
(Fig.3) Fig.2-3Illustrations in this manual common use the image of 
FV-1
1VHL2, and     mark for FV-1 1VHL2 only, others are 
same for FV-1 1VH2.INSTALLA TION   (JO IST M OUNTING -  ) Fig.3Fan body
Suspension
bracketSuspension
bracket
Suspension
bracket
Suspension
bracket
Fan body Suspension
bracket Suspension
bracket Suspension
bracket
Fan body Fan body
Joist
4 Long screws (ST4.2X20) 2 Screw   (ST4.2X8)
Suspension bracket Suspension bracket2. Insert the suspension bracket into the fan...

6. Refer to wiring diagram (Page.5)
    Follow all the local electrical safety codes. As well as
    the National Electrical Code (NEC).
    Using UL approved  wire nuts, connect house power
    wires to ventilating fan wires (Fig.6):
    Black to black; white to white; green to green.
    Make sure all connections are fastened firmly after 
    wiring is finished.
    Replace the junction box plate, and then replace
    lighting cord to hook. (Fig.5)
Fig.10 Fig.9 Fig.8Fig.5
8. Finish ceiling work....

Fig.11
Fig.12
Fig.12 Fig.11Illustrations in this manual common use the image of 
FV-1
1VHL2.INST ALLA TION     (B ETWEEN JOIS T MOUNTING) Suspension
bracket
Suspension
bracket Suspension
bracket
Fan body
Fan body Joists
Adaptor
Junction box
Suspension bracket CB
(Select the suspension bracket according to spacing A
as shown below.) Spacing A on center joists
16 inches
19.2 inches horizontal joists
19.2 inches vertical joists
B
13 1/4 ~ 15 1/2 (336~394)
14 3/4 ~ 16 3/4 (374~425)
16 1/2 ~ 18 3/4 (419~476)...

Fig.15
Fig.16
(Fig.15, Fig.16)INST
ALLATION      (W OODEN H EADER INSTALL ATION )
11 3/8 (2 90)
19 7/8 (5 05) Adaptor
Fan body
Ceiling joist
Ceiling joist
Header
Adaptor Circular
duct
Long screw (ST4.2X20) 4. Follow step 5 of installation    (page 7) to complete the
    installation work.1. Before installation, remove warning lable and the tape 
    that is securing the adapter and the damper. (Fig.1)
INST
ALLA TION     (B ETWEEN JOIS T MOUNTING)  CON TINUED Fig.13, Fig.14
Fig.14
6. Follow step 5 of...

Fig.17
Fig.18
Fig.19
Fig.20Fig.17
Fig.18
Fig.19
Fig.20 oo
60 C(140 F).
MAIN TENANC E    (CLEANIN G)
 2 1Slot
Mounting spring
Grille
Gloves
Vacuum cleaner 1
5. Replace grille.Do not allow
 any water to  get into the motor.