Panasonic Ventilation Fan Fv 05vs1 Installation Instructions

Ventilating Fan
FV-05VS1
FV-08VS1
READ AND SAVE THESE INSTRUCTIONS.R
Please
readthese
instructionscarefullybeforeattempting
toinstall,
operate or service the Panasonic Ventilating Fan. Failure to comply
with instructions could result in personal injury and/or property
damage. Please retain this booklet for future reference.
Description
Dimensions
Specifications
Table of Contents
Supplied Accessories
Unpacking
General Safety Information
4
4-54 32 2
5
Wiring Diagram
13 12 8-9
10
10-11
Installation( In...

FV-05VS1
FV-08VS1
These Panasonic ceiling mount ventilation fans use a sirocco fan driven by a capacitor motor. The motor
is designed to have an extended service life with reduced energy consumption. It also incorporates a
thermal-cutoff for safety. The grille covering the main body is a spring-loaded, quick-release type. A damper
for preventing counterflow is provided.
1 81Thumb screwLong screw
(M4X30)Quantity Appearance
Part name
Grille
Suspension
bracketI
Suspension
bracketII
1
1
Screw
(M4X8)I2...

Unit: ( )inches mm
(For 16 inches on center joists, only use suspension bracket . For 19.2 inches on center joists, only use
suspension bracket . If more than 19.2 inches on center joists, use suspension bracket & .)I
III II III
FV-05VS1 FV-08VS1
Junction box cover
Junction box
Motor
Blade
Part name No. Part nameNo.
1
2
3
4
56
7
8
9
10
Damper Fan bodyAdaptor
Grille
Suspension bracketBracket cover
1/2 13()
36/895()
31/8 78()
31/8 78()
11/2 38()
125()23/860()
7
10 1/4 261()
12 300()
3 (76)
13 330()
10 1/4...

Specifications are based on HVI standard.
Unpack and carefully remove unit from carton.
Refer to the Supplied Accessories list to verify that all parts are present.
1. Do not install this ventilating fan where air temperature may exceed 40 C (104 F).oo
2. Make sure that the electric service supply voltage is 120V, 60 Hz.
3. Follow all local electrical and safety codes, as well as the National Electrical Code (NEC) and the Occupation
Safety and Health Act (OSHA).
4. Always disconnect the power source...

CAUTION:
1. For general ventilating use only. Do not use to exhaust
hazardous or explosive materials and vapors.
2. Not for use in cooking area. (Fig. B)
3. This product must be properly grounded.Floor
Do not install above or(Cooking area)
inside this area
45o45o
equipmentCooking
Fig. B
WARNING:
To reduce the risk of fire, electric shock or injury to persons, observe the following:
A. Use this unit only in the manner intended by the manufacturer. If you have any questions, contact
to the manufacturer.
B....

6
2 Screw (M4X8)I
Suspension bracketIIISuspension bracketII
2. Insert the supension bracket into the fan body and
adaptor. (Select the suspension bracket as shown below)
Spacing A on center joists
Insert Suspension bracket
12 inches
16 inches
19.2 inches vertical joists
24 inchesRefer to Fig. 2-1
Refer to Fig. 2-2
Refer to Fig. 2-3
Refer to Fig. 2-4
If spacing A on center joists is 24 inches, connect
suspension bracket and (C4 mark to C4 mark)
as shown below :II III
Joists
ASuspension
bracketI
Fig.2-1...

2 Long screws
(M4X30)
screw (M4X10)II
Fan bodyJoist
2 Long screws
(M4X30)
Joist
4 Long screws (M4X30)Fan body
5. Remove junction box cover and secure conduit or
stress relief to junction box knock-out hole. (Fig. 5)
6. Refer to wiring diagram (page 5).
Using wire nuts, connect house power wires to
ventilating fan wires:
black to black; white to white; green to green;
Replace the junction box cover. (Fig. 5)
CAUTION:Mount junction box cover carefully so that lead
wires are not pinched. 4. Install the...

CAUTION:Joists Adaptor
2 Long screws
(M4X30)
Fig. 7
CeilingSlotMounting spring
Grille
12 1/8(305)
inches mm()Fig. 8
8. Finish ceiling work. Ceiling hole should be aligned
with the edge of the flange. (Fig. 6)
9. Insert mounting springs into slots as shown and
mount grille to fan body. (Fig. 7)
8
1. Disconnect plug connector from receptacle and
remove adaptor from fan body before starting
installation.
2. Insert the suspension bracket into the adaptor and
secure it to joists by using long screws (M4X30)....

9
Fig. 9
Fig. 11
2 Long screws
(M4X30)screw (M4X10)II
Conduit
Junction box cover
Circular duct
Joist
Fan body
Adaptor
claws
9
Make sure that adaptor claws are properly inserted
into body slots.
IMPORTANT:
5. Insert the fan body into joists. (Fig. 9)
6. Secure the fan body to adaptor by using thumb
screw and plug connector to receptacle. (Fig. 10)
7. Secure to joists by using
long screws (M4X30) and secure it to fan body by
using screw (M4X10) in vertical direction. (Fig. 11)the suspension bracket
II
8....

10
C1
C2
C3
C44 kinds of -joist
inches (mm)I
9/16 ( )14.3
11/16 (17.5)
31/32 (24.6)
1 17/32 38.9()
Suspension bracket
The suspension can comply with
different kinds of -joist.III
III
I bracket
1. Before installation, Secure the fan body to adaptor by
using thumb screw. (Fig. 1 of page 6)
2. Connect the suspension to fan body. (Fig. 13)
(Select the hole by checking joist size fix the screw
to the frame hole.)bracketIII
I-
3. Connect the ventilating fan to the joist. (Fig. 14)I-
4. Follow step 5 to 9 of...