Philips Htr5000 User Manual

							DIGITAL  A/V SURROUND RECEIVER
User manual
Thank you for choosing Philips.
Need help fast?
Read your Quick-Use Guide and/or User Manual first for quick 
tips that make using your Philips product more enjoyable. 
If you have read your instructions and still need assistance, 
you may access our online help at www.philips.com/support 
HTR5000
 
						

							2
8239 300 38591
Important notes for users in the
U.K.
Mains plug
This apparatus is fitted with an approved 13
Amp plug.  To change a fuse in this type of plug
proceed as follows:
1Remove fuse cover and fuse.
2Fix new fuse which should be a BS1362 5
Amp, A.S.T.A. or BSI approved type.
3Refit the fuse cover.
If the fitted plug is not suitable for your socket
outlets, it should be cut off and an appropriate
plug fitted in its place.
If the mains plug contains a fuse, this should
have a value of 5 Amp. If a plug without a fuse
is used, the fuse at the distribution board
should not be greater than 5 Amp.
Note:  The severed plug must be disposed of to
avoid a possible shock hazard should it be
inserted into a 13 Amp socket elsewhere.
How to connect a plug
The wires in the mains lead are coloured with
the following code: blue = neutral (N),
brown = live (L).
¶ As these colours may not correspond with the
colour markings identifying the terminals in
your plug, proceed as follows:
– Connect the blue wire to the terminal
marked N or coloured black.
– Connect the brown wire to the terminal
marked L or coloured red.
– Do not connect either wire to the ear th
terminal in the plug, marked E (or  e) or
coloured green (or green and yellow).
Before replacing the plug cover, make cer tain that the cord grip is clamped over the sheath
of the lead - not simply over the two wires.
Copyright in the U.K.
Recording and playback of material may
require consent. See Copyright Act 1956 and
The Performer’s Protection Acts 1958 to 1972.
 Norge
T ypeskilt finnes på apparatens underside.
Observer: Nettbryteren er sekundert
innkoplet. Den innebygde netdelen er
derfor ikke frakoplet nettet så lenge
apparatet er tilsluttet nettkontakten.
For å redusere faren for brann eller elektrisk
støt, skal apparatet ikke utsettes for regn eller
fuktighet.
  Italia
DICHIARAZIONE DI CONFORMITa’
Si dichiara che l’apparecchio  HTR5000 PHILIPS
r isponde alle prescrizioni dell’ar t. 2 comma 1 del
D .M. 28 Agosto 1995 n. 548.
Fatto a Eindhoven
Philips Consumer ElectronicsPhilips, Glaslaan 2
5616 JB Eindhoven, The Netherlands
CA UTION
Use of controls or adjustments or
performance of procedures other
than herein may result in hazardous
radiation exposure or other unsafe
operation.
VA ROITUS
Muiden kuin tässä esitettyjen
toimintojen säädön tai asetusten
m uutto saattaa altistaa vaaralliselle
säteilylle tai muille vaarallisille
toiminnoille.
This AV Receiver is in
conformity with the EMC
directive and low-voltage
directive.
 
						

							3
English
Français
Español
Nederlands
Italiano Deutsch
8239 300 38591
Manufactured under license from Dolby
Laboratories. “Dolby”, “Pro Logic” and
the double-D symbol are trademarks of
Dolby Laboratories.
Manufactured under license from Digital
Theater Systems, Inc. U.S. Pat. No’s.
5,451,942; 5,956,674; 5,974,380; 5,978,
762; 
6,226,616; 6,487,535 and other U.S.
and world-wide patents issued and
pending.  “DTS” and “DTS Digital
Surround” are registered trademarks of
Digital Theater Systems, Inc. Copyright
1996,  2003 Digital Theater Systems,  Inc.
All Rights Reversed.
This product complies with the radio
interference requirements of the
European Community.
Index
English ------------------------------------------------ 4
F rançais -------------------------------------------- 23
Español --------------------------------------------- 42
Deutsch --------------------------------------------- 61
Nederlands ---------------------------------------- 80
Italiano ---------------------------------------------- 99
 
						

							English
4
8239 300 38591
General Information
Supplied accessories ............................................ 5
Care and safety information .............................. 5
Connections
Step 1: Set up the speakers ................................ 6
Step 2: Placing the speakers and subwoofer .. 6
Step 3: Connecting speakers and subwoofer 7
Step 4: Connecting FM/MW antennas ............ 8
Step 5: Connecting the power cord ................ 8
Optional Connections - Playback
Connecting to TV/VCR/other audio
devices .................................................................... 9
Connecting to a DVD/SACD player .............. 10
Option 1: Using 6 Channel In jacks .......... 10
Option 2: Using Coaxial In jack ................ 10
Option 3: Using Optical In jack ................. 10
Optional Connections - Recording
Connecting to a recording device .................. 11
Functional Overview
Main unit and remote control ......................... 12
Control buttons available on the
remote only ................................................... 13
Getting Started
Step 1: Inserting batteries into the
remote control ................................................... 14
Using the remote control to operate
the system ...................................................... 14
Step 2: Switching On/Off .................................. 14
Switching to an active mode ...................... 14
Switching to standby mode ........................ 14
Step 3: Setting the speakers ...................... 14–15
Adjusting the speaker output levels ......... 15
Sound  Controls
Selecting surround sound ................................. 16
Selecting digital sound effects .......................... 16
Adjusting the Bass/Treble level ........................ 16
Volume Controls and Other
Features
Volume Control .................................................. 17
Night Mode - turning on/off ............................ 17
Dimming system’s display screen .................... 17
Setting the Sleep Timer ..................................... 17
Tuner Operations
Tuning to radio stations .................................... 18
Presetting radio stations ................................... 18
Automatic presetting ................................... 18
Manual presetting ......................................... 18
Selecting a preset radio station ....................... 19
Troubleshooting......................................... 20
Specifications............................................... 21
Glossary........................................................22
Contents
 
						

							English
5
8239 300 38591
Supplied accessories
General Information
Audio cables
(red, white)
Coaxial cable
FM wire antenna
MW loop antenna
Remote control and
two batteries
Power cable
Speaker brackets
and screws
Care and safety information
Av oid high temperatures, moisture,
water and dust
–A pparatus shall not be exposed to
dripping or splashing.
– Do not place any sources of danger on
the apparatus (e.g. liquid filled objects,
lighted candles).
Do not block any ventilation
openings
– Place the apparatus in a location with
adequate ventilation to prevent internal
heat build up.  Allow at least 10cm
(4 inches) of free space all around the
a pparatus for adequate ventilation.
Finding a suitable location
– Place the player on a flat, hard, stable
surface.
– Do not position the set on top of
other equipment that might heat it up (e.
g. DVD player or amplifier).
Care of the cabinet
– Use a soft cloth slightly moistened
with a mild detergent solution. Do not
use a solution containing alcohol, spirits,
ammonia or abrasives.
10 cm
(4 inches)
10 cm
(4 inches) 10 cm
(4 inches
)DVD Home Cinema SystemPHILIPS
(5x)
TV DISC TUNER AUX
DVD MENUDISC
SYSTEMVOL
PLAY/PAUSE
STOP RESUME
SUBW REAR CENTER TV VOL
REPEAT REPEAT
SLEEP DIM
SURROUND SOUND NIGHT MUTE
 
						

							English
6
8239 300 38591
Connections
11
33
2
4
2
Step 2: Placing the speakers
and subwoofer
Front Speaker
(Left)Front Speaker
(Right) AV Receiver
SubwooferRear speaker
(Right) Rear speaker
(Left)Centre
speaker
You can choose to hang the speakers on
the wall.  Attach the supplied bracket
firmly to the rear of speakers using the
supplied screws.  Then mount a screw
(not supplied) on the wall where the
speaker is to be hung and hook the
speaker securely onto the mounted
screw.
CAUTION!
You should get a qualified person to
attach the brackets to the wall.  DO
NOT do it by yourself to avoid
unexpected damage to the
equipment or injury to personnel.
Helpful Hints:
–The rear speakers are labelled as REAR L
(left) or REAR R (right).
–The front speakers are labelled as
FRONT L (left) or FRONT R (right).
Step 1: Set up the speakers
For best possible surround sound, all the
speakers (except subwoofer) should be
placed at the same distance from the
listening position.
1Place the front left and right speakers at
equal distances from the TV and at an
angle of approximately 45 degrees from
the listening position.
2Place the centre speaker above the TV or
the AV receiver so that the centre
channel’s sound is localised.
3Place the rear speakers at normal
listening ear level facing each other or
mounted on the wall.
4Place the subwoofer on the floor near
the TV.
Helpful Hints:
–To avoid magnetic interference, do not
position the front speakers too close to your
TV.
–Allow adequate ventilation around the AV
receiver.
 
						

							English
7
8239 300 38591
Step 3: Connecting speakers
and subwoofer
Front Right
Rear Right Rear LeftCentre
Connections
Subwoofer Front Left
●Connect the supplied speaker systems by
matching the colours of the jacks and
speaker cables.  Fully insert the stripped
portion of the speaker wire into the
jacks.
Speakers / Subwoofer   - +FRONT LEFT (FL) black white
FRONT RIGHT (FR) black red
FRONT CENTER (FC) black green
REAR LEFT (RL) black blue
REAR RIGHT (RR) black gray
SUBWOOFER (SUBW) black purple
Helpful Hints:
–Ensure that the speaker cables are
correctly connected.  Improper connections
may damage the system due to short-circuit.
–Do not connect more than one speaker to
any one pair of +/- speaker jacks.
–Do not connect speakers with an
impedance lower than the speakers supplied.
Please refer to the SPECIFIC ATIONS section
of this manual.
(75     )   L              L           
R    
++  
(     )   SPEAKERS  3   SPEAKERS  3
FRONT 
RIGHTFRONT 
LEFTREAR
LEFT REAR
RIGHT FRONT
CENTERSUB-
WOOFERFRONT RIGHTFRONT LEFT
REAR RIGHTREAR LEFT FRONT CENTER
SUBWOOFER6 CHANNEL IN
COAXIAL IN
OPTICAL IN
AUX TV
AUDIO
ANTENNA
MW
FM
AC MAINS
IN                        OUTCOAXIAL OUT
 
						

							English
8
8239 300 38591
   L              L           
R    
+ +   SPEAKERS  3
RIGHT
LEFT
REAR RIGHTREAR LEFT FRONT CENTER
SUBWOOFER
6 CHANNEL IN
COAXIAL IN
COAXIAL OUT
OPTICAL IN
AUX TV
IN                        OUT
AUDIOANTENNA
MW
(75    )FM
2
➠
1
                             OUTCOAXIAL OUT
FM
antenna
MW
antenna fix the claw into
the slot
Step 4: Connecting FM/MW
antennasStep 5: Connecting the
power cord
After everything is connected
properly, plug in the AC power cord
to the power outlet.
Never make or change any connections
with the power switched on.
Helpful Hint:
–Refer to the type plate on the rear or
bottom of the system for identification and
supply ratings.
Connections
1Connect the supplied MW loop antenna
to the MW jack.  Place the MW loop
antenna on a shelf or attach it to a stand
or wall.
2Connect the supplied FM antenna to the
FM jack.  Extend the FM antenna and fix
its ends to the wall.
For better FM stereo reception, connect
an external FM antenna (not supplied).
 
Helpful Hints:
–Adjust the position of the antennas for
optimal reception.
–Position the antennas as far as possible
from your TV, VCR or other radiation source
to prevent unwanted interference.
 
						

							English
9
8239 300 38591
IMPORTANT!
–You can connect other audio and audio/visual equipments to this AV receiver
in order to use the Home Cinema Audio System’s surround sound capabilities.
–F or connection to additional components, the audio/video cables are not
supplied.
– When making connections, make sure the colour of cables matches the
colour of jacks.
–A lways refer to the instruction manual of the connected equipment to make
an optimal connection.
Optional Connections - Playback
Connecting to TV/VCR/other
audio devices
● To hear the TV channels through this AV
r eceiver, use the audio cables (white/red)
to connect AUDIO IN- TV jacks  to the
corresponding AUDIO OUT jacks on the
TV (see fig  A).
TV
DISC TUNER AUX
VOL
TV
VOL  +-
Before starting operation,
1 Start  playing back  the connected source
as usual.
2Press  TV on the remote to activate the
input source, then press  VO L +-  to
adjust the volume level.
● To hear the playback of other audio/visual
devices (such as VCR, MP3 player,
cassette player), use the audio cables
(white/red) to connect AUDIO IN- AUX
jacks  to the corresponding AUDIO OUT
jacks on the connected audio device (see
fig  B).
TV/AV
DISC TUNER AUX
VOL
AUX
VOL  +-
Before starting operation,
1 Start  playing back  the connected source
as usual.
2Press  AUX on the remote to activate
the input source, then press  VO L +-
to adjust the volume level.
BVCR/CD/Tape player (for example)
AUDIOOUTS-VIDEO IN
VIDEO IN
SCART IN
AUDIO OUTS-VIDEO
IN
VIDEO INSCART IN
   L              L           
R
  \b
    
++  
(     )   SPEAKERS  3   SPEAKERS  3
FRONT  RIGHT FRONT 
LEFT REAR
LEFT
REAR
RIGHT
FRONT
CENTER SUB-
WOOFERFRONT RIGHT
FRONT LEFT
REAR RIGHTREAR LEFT
FRONT CENTER
SUBWOOFER6 CHANNEL IN
COAXIAL IN
COAXIAL OUT
OPTICAL IN
AUX TV
AUDIO
ANTENNAMW
(75     )FM
IN                         OUTCOAXIAL OUT
AUDIO OUTL
R
A
 
						

							English
10
8239 300 38591
Optional Connections - Playback
OR
Connecting to a DVD/SACD
player
ABC
OR
D
VD/SACD
player
Y ou only need to make 
one connection
to your DVD/SACD player from the
f ollowing options, depending on the
capabilities of your DVD/SACD player.
Option 1: Using 6 Channel In jacks
● If your DVD/SACD player has a built-in
multichannel decoder (e.g. Dolby Digital,
DTS) and has 6-channel (multichannel)
output jacks, you may use the audio
cables (not supplied) to connect the AV
r eceiver’s  6 CHANNEL IN  jacks to the
corresponding output jacks on the
D VD/SACD player (see fig  A).
Before starting operation,
1 Start  playing back  the connected source
as usual.
2Press  DISC  on the remote to select
“ DISC 6CH ” in order to activate the
input source, then press  VO L +-  to
adjust the volume level.
Helpful Hints:
– The audio signals produced by 6 channel is
m ultichannel surround.  Therefore, switching to
Stereo mode has no effect.
– Making recording from this input is not
possible. Option 2: Using Coaxial In jack
● Or, use an coaxial cable to connect the
AV receiver’s  COAXIAL IN  jack to the
COAXIAL output jack on the
D VD/SACD player (see fig  B).
Before starting operation,
1  Start  playing back the connected source
as usual.
2 Press  DISC  on the remote to select
“ DISC COAX ” in order to activate the
input source, then press  VO L +-  to
adjust the volume level.
Option 3: Using Optical In jack
● Or, use an optical fiber-optic cable (not
supplied) to connect the AV receiver’s
OPTICAL IN  jack to the OPTICAL
output jack on the DVD/SACD player
(see fig  C).
Before starting operation,
1 Start  playing back  the connected source
as usual.
2Press  DISC  on the remote to select
“ DISC OPTI ” in order to activate the
input source, then press  VO L +-  to
adjust the volume level.