Philips LaserMFD 6050 WLAN User Manual

							LFF6050
- 36 -
6 - Parameters/Setup
Printing the functions guide
51 - PRINT / FUNCTIONS LIST
Press , enter 51 using the keypad.
The printing of the functions guide starts.
Printing the logs
The incoming and outgoing logs list the last 30 
transmissions (incoming and outgoing) made by your 
machine.
An automatic print out will take place after every 30 
transmissions. However, you may request a print out at 
any time.
Each log (incoming or outgoing) contains a table with the 
following information:
• date and time of the incoming or outgoing document,
• subscriber’s number or E-mail address,
• transmission mode (Normal, Fine, SFine or Photo),
• number of pages sent or received,
• call duration,
• incoming or outgoing results: noted CORRECT if 
properly transmitted, 
or 
information codes for special calls (polling, manual 
subscribers, etc.)
• reason for call error (example: your subscriber does 
not answer).
To print the logs:
54 - PRINT / LOGS
Press , enter 54 using the keypad.
The printing of the logs starts. The incoming and outgoing 
logs are printed on the same page.
11 - RX speedTransmission speed for incoming 
documents. 
For a quality telephone line 
(compatible, no echo), 
communications occur at 
maximum speed.
However, it may be necessary to 
restrict the transmission speed for 
some calls.
12 - RingsNumber of rings to automatically 
start your machine.
13 - Discard sizeThe Discard Size parameter only 
defines the printing of received 
faxes. The number of lines of a 
document can be too high for the 
printing paper format. This 
parameter defines the threshold 
beyond which the extra lines are 
printed on a second page. Below 
this threshold, extras lines are 
deleted.
If you choose ON, the threshold is 
set on 3 centimeters.
If you choose OFF, the threshold is 
set on 1 centimeter.
20 - E.C.M.This parameter helps correct the 
calls made on disturbed telephone 
lines. It is used when the lines are 
weak or too noisy. Transmission 
times may be longer.
25 - TEL ImpedanceThis parameter lets you choose 
between a complex impedance 
and a 600 Ohm impedance, 
depending on the telephone 
network your terminal is connected 
to.
80 - Toner save Makes printing lighter to save toner 
cartridge ink.
90 - RAW Port RAW network print port 
connection.
91 - Printer error 
timeoutTime-out before document being 
printed is deleted following a print 
error in PC print mode.
92 - Printer wait 
timeoutWait time-out for data from PC 
before the task is deleted in PC 
print.
93 - Replace formatPage format change. This 
parameter allows you to print a 
LETTER format document on A4 
pages using the LETTER/A4 
setting.
96 - NBR. WEP 
KeysNumber of WEP keys allowed 
(from 1 to 4).
Parameter Signification
ImportantThe printing is not possible on A5 
(or Statement) paper format.
NoteYou can also access the PRINT menu 
by pressing the   button.
ImportantThe printing is not possible on A5 
(or Statement) paper format.
NoteYou can also access the PRINT menu 
by pressing the   button.
Downloaded From ManualsPrinter.com Manuals 
						

							LFF6050
- 37 -
6 - Parameters/Setup
Print the list of setups
To print the list of setups:
56 - PRINT / SETUP
Press , enter 56 using the keypad.
The printing of the list of setups starts.
Lock the machine
This function prevents non-authorized people from 
accessing the machine. An access code will be required 
every time someone wants to use the device. After each 
use, the device will lock automatically.
Before that you have to enter a lock code.
811 - ADVANCED FCT / LOCK / LOCKING CODE
1Press , enter 811 using the keypad.
2Enter your lock code (4 digits) with the keyboard, 
confirm with OK.
3Enter again your lock code (4 digits) with the 
keyboard, confirm with OK.
4Quit this menu by pressing the   button.
Lock the keyboard
Every time you use your machine, you will have to enter 
your code.
812 - ADVANCED FCT / LOCK / LOCK KEYBD.
1Press , enter 812 using the keypad.
2Enter the four-digit locking code with the keypad.
3Press OK to confirm.
4With the buttons  or , choose ON and confirm 
with OK.
5Quit this menu by pressing the   button.
Lock the numbers
This function locks dialling and the numerical keypad is 
disabled. Transmissions are only possible from numbers 
included in the directory.
To access the number interlocking option:
813 - ADVANCED FCT / LOCK / LOCK NUMBER
1Press , enter 813 using the keypad.2Enter the four-digit locking code with the keypad.
3Press OK to confirm.
4With the buttons  or , choose DIRECT ONLY
and confirm with OK.
5Quit this menu by pressing the   button.
Lock the SMS service
This function prevents access to the SMS service.
To access the SMS service locking menu:
815 - ADVANCED FCT / LOCK / LOCK SMS
1Press , enter 815 using the keypad.
2Enter the four-digit locking code with the keypad.
3Press OK to confirm.
4With the buttons  or , choose ON and confirm 
with OK.
5Quit this menu by pressing the   button.
Lock the Media service
This function prevents access to the Media service. The 
access code will be required every time someone wants 
to use the USB key functions:
• analyse the contents of a connected USB key,
• print from a USB key, delete files,
• archive received faxes on a USB key.
To access the Media service locking menu:
816 - ADVANCED FCT / LOCK / LOCK MEDIA
1Press , enter 816 using the keypad.
2Enter the four-digit locking code with the keypad.
3Press OK to confirm.
4With the buttons  or , choose ON and confirm 
with OK.
5Quit this menu by pressing the   button.
Read the counters
This function allows you to view the activity counters for 
your machine at any time.
According to your needs, you can read the counters for:
• sent pages,
• received pages,
• scanned pages,
• printed pages.
Sent pages counter
To view the number of pages sent from your machine:
821 - ADVANCED FCT / COUNTERS / SENT PAGES
1Press , enter 821 using the keypad.
2The number of sent pages appears on the screen.
3Quit this menu by pressing the   button. ImportantThe printing is not possible on A5 
(or Statement) paper format.
NoteYou can also access the PRINT menu 
by pressing the   button.
ImportantIf a code is already registered, enter 
the old code before typing the new 
one.
Downloaded From ManualsPrinter.com Manuals 
						

							LFF6050
- 38 -
6 - Parameters/Setup
Received pages counter
To view the number of pages received on your machine:
822 - ADVANCED FCT / COUNTERS / RECEIVED 
PG
1Press , enter 822 using the keypad.
2The number of received pages appears on the 
screen.
3Quit this menu by pressing the   button.
Scanned pages counter
To view the number of pages scanned on your machine:
823 - ADVANCED FCT / COUNTERS / SCANNED 
PAGE
1Press , enter 823 using the keypad.
2The number of scanned pages appears on the 
screen.
3Quit this menu by pressing the   button.
Printed pages counter
To view the number of pages printed on your machine:
824 - ADVANCED FCT / COUNTERS / PRINTED PG
1Press , enter 824 using the keypad.
2The number of printed pages appears on the 
screen.
3Quit this menu by pressing the   button.
Display the consumables status
You can read at any time the remaining toner in the 
cartridge. This level appears in percentage.
86 - ADVANCED FCT / CONSUMABLES
1Press , enter 86 using the keypad.
2The available toner percentage appears on the 
screen.
3Quit this menu by pressing the   button.
Calibrate your scanner
You can do this operation when the quality of photocopied 
documents is not satisfactory anymore.
80 - ADVANCED FCT / CALIBRATION
1Press , enter 80 using the keypad. Confirm 
with OK.
2The scanner is triggered and a calibration is done 
automatically.
3At the end of the calibration, the machine comes 
back to the screen saver
.
Downloaded From ManualsPrinter.com Manuals 
						

							LFF6050
- 39 -
7 - Directory
Directory
Your multifunction machine lets you create a directory by 
memorising subscriber records and subscriber lists. Your 
machine can store up to 250 subscriber records, which 
you can group in 20 subscriber lists.
For all subscriber records or subscriber lists you may 
create, consult, modify or delete contents. You can also 
print the directory.
Furthermore, your machine lets you create and manage 
your phone directory from your PC Kit. For more 
information on this feature, refer to chapter PC Features, 
page 52.
Creating subscribers record
To create subscribers record:
11 - DIRECTORY / NEW CONTACT
1Press , enter 11 using the keypad.
2Enter the NAME of your contact with the 
alphanumerical keypad (20 characters maximum), 
confirm with OK.
3Enter the TEL number of your contact with the 
numerical keypad (30 digits maximum), confirm 
with OK.
4Choose the RECORD NO from your directory with 
the numerical keypad or accept the displayed 
number, and confirm with OK.
5Select W. ASSOC. KEY if you want to assign a 
shortcut key (letter) to your subscriber record. The 
first available letter appears, use  or  to choose 
another letter. Confirm with OK.
6Select the appropriate transmission RATE to send 
faxes among the values 2400, 4800, 7200, 9600, 
12000, 14400 and 33600 using  or . Confirm 
with OK. 
The maximum speed can be used if the telephone 
line is of good quality, meaning appropriate, 
without echo.
Creating subscribers list
To create subscribers list:
12 - DIRECTORY / NEW GROUP
1Press , enter 12 using the keypad.
2Enter the LIST NAME with the alphanumerical 
keypad (20 characters maximum), confirm 
with OK.
3 CALLED NUMBER: use  or  to select from 
existing records the contacts of your list and 
confirm with OK. Repeat this operation for each 
subscriber you want to add to your list.
4Enter the GROUP NUMBER assigned to your list 
with the numerical keypad or accept the displayed 
number, and confirm with OK.
Modifying a record
To modify a subscribers record or list:
13 - DIRECTORY / MODIFY
1Press , enter 13 using the keypad.
2With  or , browse the directory and select the 
record or list you want to modify by pressing OK.
3With  or , browse the entries of the selected 
record or list. Press OK when the entry you want to 
modify appears on screen.
4The cursor appears at the end of the line. Press C 
to delete characters.
5Enter the new entry and confirm with OK.
6Repeat the operations for each line you want to 
modify.
Deleting a record or a list
To delete a subscribers record or list:
14 - DIRECTORY / CANCEL
1Press , enter 14 using the keypad.
2With  or , browse the directory and select the 
record or list you want to delete by pressing OK.
3Press OK to confirm the deletion.
4Repeat the operations for each record or list you 
want to delete. ImportantIf your multifunction machine is 
connected to a PABX, you may 
insert a pause for dial tone after the 
outgoing local prefix dialling.
To insert a pause for dial tone (/ 
sign), press simultaneously the 
C
TRL and M keys, or long press the 
0 (zero) key on the numerical 
keypad until the / sign is displayed.
For more details, refer to Local 
prefix, page 32.
ImportantIn the directory, the letter G placed 
next to a name identifies a 
subscribers group.
Downloaded From ManualsPrinter.com Manuals 
						

							LFF6050
- 40 -
7 - Directory
Printing the directory
To print the directory:
15 - DIRECTORY / PRINT
Press , enter 15 using the keypad.
The printing of the directory starts, in alphabetical order.
Saving/Restoring the directory 
(Smart card option)
This function enables you to save the contents of your 
directory on a Smart card and restore them on your 
machine.
To save the contents of your directory on your Smart 
card:
161 - DIRECTORY / SAVE/LOAD / SAVE
1Press , enter 16 using the keypad.
2Select SAVE to save directory entries on the Smart 
card and confirm with OK.
3Insert your Smart card.
To restore the contents of your directory from your Smart 
card:
162 - DIRECTORY / SAVE/LOAD / LOAD
1Press , enter 16 using the keypad.
2Select LOAD to restore directory entries from the 
Smart card and confirm with OK.
3Confirm with OK.
4Insert your Smart card. ImportantThe printing is not possible on A5 
(or Statement) paper format.
NoteYou can also print the directory with 
menu 
55 - PRINT / DIRECTORY.
ImportantThis function is only available to 
service technician with Smart 
card.
Downloaded From ManualsPrinter.com Manuals 
						

							LFF6050
- 41 -
8 - Games and Calendar
Games and 
Calendar
Sudoku
Sudoku is a Japanese puzzle. The game is in a grid 
format of three squares by three squares to be distributed 
in fields in zones of 3 × 3. Depending on the level of 
difficulty, more or fewer numbers are already entered at 
the start of the game. The aim of the game is to distribute 
the numbers 1 to 9 between the boxes in such a way that 
each number appears only once in each row, column and 
in each of the nine grids. There is only one solution.
Print a grid
There are 400 Sudoku grids available in total, 100 for 
each difficulty level.
 521 - PRINT / SUDOKU / PRINT GRID
1Press , enter 5 using the keypad. Confirm 
with OK.
2Select SUDOKU using the  or  button.
3Confirm with OK.
4Select PRINT GRID using the  or  button.
5Select the level of difficulty EASY, MEDIUM, 
HARD, EVIL using the  or  button.
6Confirm with OK.
7Choose the grid you want by entering the number 
on the numeric keypad (1 to 100).
8Confirm with OK.
9Choose the number of copies you want by entering 
a number from 1 to 9 on the numeric keypad.
10Confirm with OK.
The number of copies of the grid requested is printed.
Print the solution to a grid
 522 - PRINT / SUDOKU / PRT SOLUTION
1Press , enter 5 using the keypad. Confirm 
with OK.
2Select SUDOKU using the  or  button.3Confirm with OK.
4Select PRT SOLUTION using the  or  button.
5Select the level of difficulty EASY, MEDIUM, 
HARD, EVIL using the  or  button.
6Confirm with OK.
7Choose the grid you want by entering the number 
on the numeric keypad (1 to 100).
8Confirm with OK.
9Choose the number of copies you want by entering 
a number from 1 to 9 on the numeric keypad.
10Confirm with OK.
The number of copies of the solution to the grid requested 
is printed.
Calendar
This function enables you to print the calendar for a year 
of your choice.
 53 - PRINT / CALENDAR
1Press , enter 5 using the keypad. Confirm 
with OK.
2Select CALENDAR using the  or  button.
3Confirm with OK.
4Choose the year you want to print as calendar by 
entering the number on the numeric keypad (for 
example: 2009).
5Confirm with OK.
The calendar of the year requested is printed. ImportantThe printing is not possible on A5 
(or Statement) paper format.
NoteYou can also access the PRINT menu 
by pressing the   button.
ImportantThe printing is not possible on A5 
(or Statement) paper format.
NoteYou can also access the PRINT menu 
by pressing the   button.
ImportantThe printing is not possible on A5 
(or Statement) paper format.
NoteYou can also access the PRINT menu 
by pressing the   button.
NoteThe year must be between 1900 and 
2099. Use the C key to correct an 
entry.
Downloaded From ManualsPrinter.com Manuals 
						

							LFF6050
- 42 -
9 -  Network features
Network features
You may connect your multifunction terminal to a wireless 
network.
However, practical knowledge of your computer 
configuration is required to set up a network.
You can connect your machine to a PC using a USB cable 
or make a wireless connection (via radio) with a PC or 
network.
Type of radio network
A radio network or WLAN (Wireless Local Area Network) 
is created when at least two computers, printers or other 
peripheral devices communicate with each other in a 
network via radio waves (high frequency waves). The 
transmission of data in the radio network is based on the 
standards 802.11b and 802.11g. According to how the 
network is set up, it may be described as an infrastructure 
network or an ad-hoc network.
Radio infrastructure network
In an infrastructure network, several devices 
communicate via a central access point (a gateway or 
router). All data is sent to the access point (gateway or 
router) from where it is re-distributed.
Radio ad-hoc network
In an ad-hoc network, the devices communicate directly 
with each other without passing through an access point. 
The speed of communication across the whole radio 
network is as fast as the weakest connection in the 
network. The speed of communication is also dependent 
on spatial distance between transmitter and receiver, as 
well as the number of barriers, such as walls or ceilings.
Radio networks (WLAN)
Three steps are necessary to incorporate your machine 
into a radio network (WLAN):
1Configure the network to your PC.
2Set up the parameters for your machine so that it 
can function in a network.
3Having set up the parameters for your device, 
install the Companion Suite Pro software onto your 
PC with the necessary printer drivers.
Once the machine is incorporated into a WLAN network, 
you can from your PC:
• print documents on the multifunction machine from 
your usual applications,
• scan colour, grey scale or black and white documents 
on your PC. ImportantIf you have a WLAN adaptor, you 
can incorporate your machine as a 
network printer into a radio network. 
This works only with an approved 
adaptor that you can obtain from our 
ordering department. For further 
information, contact 
 
www.sagem-communications.com.
CAUTIONBeware, when you are using a 
wireless connection, that certain 
items of medical equipment, 
sensitive or security systems may 
be affected by the radio 
transmissions of your device; in all 
cases, please follow safety 
guidelines closely.
ImportantPlease note that in ad-hoc mode, 
the WPA/WPA2 encryption method 
is not available.
ImportantThe PC and all other devices must 
have their parameters set up to the 
same network as the multifunction 
machine. All the details needed for 
setting up the device, such as the 
network names (SSID), type of radio 
network, encryption key, IP address 
or subnetwork mask, must match 
the specifications of the network.
You will find these details on your 
PC or on the Access Point.
To find out how to set up the 
parameters for your PC, please 
consult the users’ manual for your 
WLAN adaptor. For large networks, 
please seek the advice of your 
network administrator.
Downloaded From ManualsPrinter.com Manuals 
						

							LFF6050
- 43 -
9 -  Network features
Connect your WLAN adaptor
Your machine belongs to a new generation of terminals 
that you can incorporate into a WLAN network using a 
WLAN USB key.
1Plug your WLAN USB key into the USB port of your 
machine.
Configure your network
Creating or rejoining a network
Before attempting to use a WLAN adaptor on your 
machine, you must enter the parameters that will allow a 
WLAN network to recognise your machine.
On your machine you will find simple instructions 
that guide you step by step through the set-up of your 
network. Just follow them! 
 281 - SETUP / WLAN / CONFIG. ASS. 
1Type in , select the menu SETUP using the keys 
 or  and confirm with OK.
2Select WLAN using the keys  or  and confirm 
with OK.
3Select CONFIG. ASS. using the keys  or  and 
confirm with OK. 
The machine searches for existing networks.
4Select your existing network, or select NEW 
NETWORK to create it, using the keys  or  and 
confirm with OK.
5 SSID appears on the screen, enter the name of 
your network using the numerical keypad, pressing 
the keys one after the other until you obtain the 
name you want (32 characters maximum) and 
confirm with OK.
6 AD-HOC MODE or INFRA. MODE appear on the 
screen. Go back to the beginning of the chapter 
and make your choice. 
Select one of these modes and confirm with OK.
- If you choose AD-HOC mode, the sub-menu 
CHANNEL appears, enter a figure between 1 
and 13 (1 to 11 for the US) and confirm with OK.
7Select your encryption method, OFF, WEP or 
WPA, and confirm with OK:
- If you choose WEP, enter the WEP key that you 
are using on your network.
- If you choose WPA, enter the WPA or WPA2 
key that you are using on your network. NoteYou can be sure of perfect 
communication if you use an 
approved adaptor in conjunction with 
your PC.
All of the latest printer drivers for the 
approved adaptor may be found on 
our website together with further 
information: 
 
www.sagem-communications.com.
ImportantYour machine’s network radio 
adaptor transmits data using the 
radio protocol IEEE 802.11g; it can 
also be incorporated into an existing 
IEEE 802.11b network.
When connecting to your machine, 
only use the approved adaptor. 
Other transmitting or receiving 
adaptors may damage your device.
Irrespective of whether you use your 
machine in an infrastructure or ad-
hoc network, you must set up certain 
network and security parameters 
(for example, the Service-Set-ID 
(SSID) and the encryption key). 
These must match the network’s 
specifications.
NoteWe recommend that the settings of 
your WLAN network should only be 
changed by a person with a good 
knowledge of the configuration of your 
computer.
NoteIf you choose an existing network, 
steps 5 and 6 (and possibly 7) are 
carried out automatically.
ImportantPlease note that in ad-hoc mode, 
the WPA/WPA2 encryption method 
is not available.
NoteThe WEP key number may be 
configured in the menu:  29 - 
SETUP / TECHNICALS / WEP KEYS 
NBR.
Downloaded From ManualsPrinter.com Manuals 
						

							LFF6050
- 44 -
9 -  Network features
8 IP CONF.: MANU or IP CONF.: AUTO appear on 
the screen. 
If you choose to set up the system manually, go to 
the next paragraph and enter the parameters 
IP ADDRESS, SUBNET MASK and GATEWAY.
9At the end of this procedure, you return to the main 
menu of CONFIG. ASS.
10Exit this menu by pressing the 
 key.
Once the network has been set up, the LED of the WLAN 
USB key should be on.
Referring to or changing your 
network parameters
Each of the parameters of your network may be changed 
as your network develops.
 2822 - SETUP / WLAN / PARAMETERS / IP 
ADDRESS
1Type in , select the menu SETUP using the keys 
 or  and confirm with OK.
2Select WLAN using the keys  or  and confirm 
with OK.
3Select PARAMETERS using the keys  or  and 
confirm with OK.
4Select IP ADDRESS using the keys  or  and 
confirm with OK.
5The number of your IP address will appear in the 
format 000.000.000.000. Enter the new IP address 
for your machine in the format displayed and 
confirm with OK.
6Exit this menu by pressing the 
 key.
 2823 - SETUP / WLAN / PARAMETERS / SUBNET 
MASK
1Type in , select the menu SETUP using the keys 
 or  and confirm with OK.
2Select WLAN using the keys  or  and confirm 
with OK.
3Select PARAMETERS using the keys  or  and 
confirm with OK.
4Select SUBNET MASK using the keys  or  and 
confirm with OK.
5The number of your subnet mask will appear in the 
format 000.000.000.000. Enter the new submask 
of your machine in the format displayed and 
confirm with OK.
6Exit this menu by pressing the 
 key.
 2824 - SETUP  /  WLAN  /  PARAMETERS  /  GATEWAY
1Type in , select the menu SETUP using the keys 
 or  and confirm with OK.
2Select WLAN using the keys  or  and confirm 
with OK.3Select PARAMETERS using the keys  or  and 
confirm with OK.
4Select GATEWAY using the keys  or  and 
confirm with OK.
5The number of your gateway will appear in the 
format 000.000.000.000. Enter the new gateway 
for your machine in the format displayed and 
confirm with OK.
6Exit this menu by pressing the 
 key.
 2825 - SETUP /WLAN / PARAMETERS / SSID
1Type in , select the menu SETUP using the keys 
 or  and confirm with OK.
2Select WLAN using the keys  or  and confirm 
with OK.
3Select PARAMETERS using the keys  or  and 
confirm with OK.
4Select SSID using the keys  or  and confirm 
with OK.
5The name of your network will appear on the 
screen. Enter the new name of your network and 
confirm with OK.
6Exit this menu by pressing the 
 key.
 2826 - SETUP / WLAN / PARAMETERS / MODE
1Type in , select the menu SETUP using the keys 
 or  and confirm with OK.
2Select WLAN using the keys  or  and confirm 
with OK.
3Select PARAMETERS using the keys  or  and 
confirm with OK.
4Select MODE using the keys  or  and confirm 
with OK.
5The symbol >>, tells you that your network is in 
active mode.
6Select one of the modes and confirm with OK.
- If you choose the AD-HOC MODE, the sub-
menu CHANNEL will appear; enter a number 
between 1 and 13 (1 to 11 for the US) and 
confirm with OK.
7Exit this menu by pressing the 
 key.
ImportantIn an AD-HOC network, the devices 
communicate directly with each 
other without passing through an 
access point. The speed of 
communication across the whole 
AD-HOC radio network is as fast as 
the weakest connection in the 
network. The speed of 
communication is also dependent on 
spatial distance between transmitter 
and receiver, as well as the number 
of barriers, such as walls or ceilings.
Downloaded From ManualsPrinter.com Manuals 
						

							LFF6050
- 45 -
9 -  Network features
 2827 - SETUP / WLAN / PARAMETERS / SECURITY
This parameter allows you to make your network secure 
by setting the encryption method to use in your WLAN 
network.
1Type in , select the menu SETUP using the keys 
 or  and confirm with OK.
2Select WLAN using the keys  or  and confirm 
with OK.
3Select PARAMETERS using the keys  or  and 
confirm with OK.
4Select SECURITY using the keys  or  and 
confirm with OK.
5Choose WEP, WPA or OFF and confirm with OK.
- If you choose WEP, enter a password: 
- In a 64 bit security configuration, the password 
must contain five characters exactly. 
- In a 128 bit security configuration, the 
password must contain 13 characters exactly.
- If you choose WPA, enter a WPA or WPA2 
password (min. 8 characters to 63 characters 
max.). 
The password can contain alphanumerical 
characters - numbers and letters - and any other 
symbol available on the keypad. The only 
invalid character is 
€ (euro currency sign).
6Exit this menu by pressing the 
 key.
 2828 - SETUP / WLAN / PARAMETERS /
HOSTNAME
The machine name allows you to identify your machine on 
the network via a PC (for example with the name PRINT-
NETWORK-1).
1Type in , select the menu SETUP using the keys 
 or  and confirm with OK.
2Select WLAN using the keys  or  and confirm 
with OK.
3Select PARAMETERS using the keys  or  and 
confirm with OK.
4Select HOSTNAME using the keys  or  and 
confirm with OK.
5Type in the desired name (15 characters 
maximum) and confirm with OK.
6Exit this menu by pressing the 
 key.
Once your connection has been set up, you must install 
the network printer driver on your PC so that you can print 
your documents.  
Refer to the paragraph Software installation, page 52.
An example of how an AD-HOC network 
may be set up
An example of how to configure an Ad-hoc network 
without security protection using the following 
parameters:
• network name: house
• radio type: ad-hoc
• channel: 1
• PC’s IP address: 169.254.0.1
• PC’s subnetwork mask: 255.255.0.0
• PC’s gateway: 0.0.0.0
• IP address of the multifunction machine: 169.254.0.2
• subnetwork mask of the multifunction machine: 
255.255.0.0
• multifunction machine’s gateway: 0.0.0.0
Setting up a multifunction machine
1Plug the WLAN USB key into the USB connector of 
the multifunction machine.
2Type in , select the menu SETUP using the keys 
 or  and confirm with OK.
3Select WLAN using the keys  or  and confirm 
with OK.
4Select CONFIG. ASS. using the keys  or  and 
confirm with OK.
5Select NEW NETWORK using the keys  or  
and confirm with OK.
6 SSID appears on the screen, enter house using 
the numerical keypad and confirm with OK.
7Select the mode AD-HOC MODE and confirm 
with OK.
8Enter 1 in the field CHANNEL and confirm 
with OK.
9Select OFF and confirm with OK.
10Select IP CONF.: MANU and confirm with OK.
11Enter 169.254.0.2 in the field IP ADDRESS and 
confirm with OK.
12Enter 255.255.0.0 in the field SUBNET MASK 
and confirm with OK.
13Enter 0.0.0.0 in the field GATEWAY and confirm 
with OK.
14At the end of this process, you return to the main 
menu of ASS. CONFIG.
15Exit this menu by pressing the 
 key.
Once the network has been set up, the LED of the WLAN 
USB key should be on.
You must now set up the PC. NoteYou may also enter the password 
using the hexadecimal system, if this 
is the case:
- For a 64 bit security configuration, 
the password must contain exactly 
10 hexadecimal characters.
 
- For a 128 bit security configuration, 
the password must contain exactly 
26 hexadecimal characters.
Downloaded From ManualsPrinter.com Manuals